From: kishon@ti.com (Kishon Vijay Abraham I)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 3/3] ARM: dts: omap: Add usb_otg and glue data
Date: Fri, 25 Jan 2013 07:54:37 +0530 [thread overview]
Message-ID: <1359080677-5381-4-git-send-email-kishon@ti.com> (raw)
In-Reply-To: <1359080677-5381-1-git-send-email-kishon@ti.com>
Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI), mode
which is mostly OTG, power that specifies the amount of power this can supply
when in host mode.
The information about this node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
Documentation/devicetree/bindings/usb/omap-usb.txt | 2 ++
arch/arm/boot/dts/omap3-beagle-xm.dts | 6 ++++++
arch/arm/boot/dts/omap3-evm.dts | 6 ++++++
arch/arm/boot/dts/omap3-overo.dtsi | 6 ++++++
arch/arm/boot/dts/omap3.dtsi | 12 ++++++++++++
arch/arm/boot/dts/omap4-panda.dts | 6 ++++++
arch/arm/boot/dts/omap4-sdp.dts | 6 ++++++
arch/arm/boot/dts/omap4.dtsi | 13 +++++++++++++
arch/arm/boot/dts/twl4030.dtsi | 2 +-
9 files changed, 58 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 704b684..90360e3 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -18,6 +18,7 @@ OMAP MUSB GLUE
represents PERIPHERAL.
- power : Should be "50". This signifies the controller can supply upto
100mA when operating in host mode.
+ - usb_phy : the phandle for the PHY device
Optional properties:
- ctrl_module : phandle of the control module this glue uses to write to
@@ -32,6 +33,7 @@ usb_otg_hs: usb_otg_hs at 4a0ab000 {
num_eps = <16>;
ram_bits = <12>;
ctrl_module = <&omap_control_usb>;
+ usb_phy = <&usb2_phy>;
};
Board specific device node entry
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 3705a81..cb07583 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -107,3 +107,9 @@
*/
ti,pulldowns = <0x03a1c4>;
};
+
+&usb_otg_hs {
+ interface_type = <0>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index e8ba1c2..afb9ba9 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -59,3 +59,9 @@
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface_type = <0>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
index 89808ce..4b3d157 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/omap3-overo.dtsi
@@ -55,3 +55,9 @@
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface_type = <0>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 1acc261..176561b 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -397,5 +397,17 @@
ti,timer-alwon;
ti,timer-secure;
};
+
+ usb_otg_hs: usb_otg_hs at 480ab000 {
+ compatible = "ti,omap3-musb";
+ reg = <0x480ab000 0x1000>;
+ interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupt-names = "mc", "dma";
+ ti,hwmods = "usb_otg_hs";
+ usb_phy = <&usb2_phy>;
+ multipoint = <1>;
+ num_eps = <16>;
+ ram_bits = <12>;
+ };
};
};
diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
index 4122efe..612c9bb 100644
--- a/arch/arm/boot/dts/omap4-panda.dts
+++ b/arch/arm/boot/dts/omap4-panda.dts
@@ -206,3 +206,9 @@
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usb_otg_hs {
+ interface_type = <1>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 43e5258..582d7ee 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -428,3 +428,9 @@
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usb_otg_hs {
+ interface_type = <1>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 5f68d68..a57ec29 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -541,5 +541,18 @@
reg-names = "control_dev_conf", "otghs_control";
ti,type = <1>;
};
+
+ usb_otg_hs: usb_otg_hs at 4a0ab000 {
+ compatible = "ti,omap4-musb";
+ reg = <0x4a0ab000 0x7ff>;
+ interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupt-names = "mc", "dma";
+ ti,hwmods = "usb_otg_hs";
+ usb_phy = <&usb2_phy>;
+ multipoint = <1>;
+ num_eps = <16>;
+ ram_bits = <12>;
+ ti,has_mailbox;
+ };
};
};
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
index ed0bc95..398d2c3 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -67,7 +67,7 @@
#interrupt-cells = <1>;
};
- twl4030-usb {
+ usb2_phy: twl4030-usb {
compatible = "ti,twl4030-usb";
interrupts = <10>, <4>;
usb1v5-supply = <&vusb1v5>;
--
1.7.9.5
prev parent reply other threads:[~2013-01-25 2:24 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-01-25 2:24 [PATCH v2 0/3] ARM: dts: omap: add dt data for MUSB Kishon Vijay Abraham I
2013-01-25 2:24 ` [PATCH v2 1/3] ARM: dts: omap: Add omap control usb data Kishon Vijay Abraham I
2013-01-25 2:24 ` [PATCH v2 2/3] ARM: dts: omap: Add omap-usb2 dt data Kishon Vijay Abraham I
2013-01-25 2:24 ` Kishon Vijay Abraham I [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1359080677-5381-4-git-send-email-kishon@ti.com \
--to=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).