linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: b32955@freescale.com (Huang Shijie)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/2] mtd: gpmi: set the Golois Field bit for mx6q's BCH
Date: Fri, 25 Jan 2013 14:04:07 +0800	[thread overview]
Message-ID: <1359093848-22301-1-git-send-email-b32955@freescale.com> (raw)

The GF13 can be only used in the following case:
    The ECC data chunk is less then 1K bytes.

In mx23/mx28, the ecc data chunk is 512 bytes. So it is okay.

But in mx6q, we begin to use some large nand chip whose ecc
data chunk maybe 1K bytes long.  So when the data chunk is 1K bytes,
we have to use the GF14.

This patch sets the Golois Field bit when the GF14 is needed.

Signed-off-by: Huang Shijie <b32955@freescale.com>
---
 drivers/mtd/nand/gpmi-nand/bch-regs.h  |   20 ++++++++++++++++++++
 drivers/mtd/nand/gpmi-nand/gpmi-lib.c  |    4 ++++
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c |    6 ++++--
 3 files changed, 28 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/gpmi-nand/bch-regs.h
index d67bca5..588f537 100644
--- a/drivers/mtd/nand/gpmi-nand/bch-regs.h
+++ b/drivers/mtd/nand/gpmi-nand/bch-regs.h
@@ -61,6 +61,16 @@
 			& BM_BCH_FLASH0LAYOUT0_ECC0)		\
 	)
 
+#define MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14	10
+#define MX6Q_BM_BCH_FLASH0LAYOUT0_GF_13_14			\
+				(0x1 << MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14)
+#define BF_BCH_FLASH0LAYOUT0_GF(v, x)				\
+	((GPMI_IS_MX6Q(x) && ((v) == 14))			\
+		? (((1) << MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT0_GF_13_14)	\
+		: 0						\
+	)
+
 #define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE		0
 #define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE		\
 			(0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)
@@ -93,6 +103,16 @@
 			& BM_BCH_FLASH0LAYOUT1_ECCN)		\
 	)
 
+#define MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14	10
+#define MX6Q_BM_BCH_FLASH0LAYOUT1_GF_13_14			\
+				(0x1 << MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14)
+#define BF_BCH_FLASH0LAYOUT1_GF(v, x)				\
+	((GPMI_IS_MX6Q(x) && ((v) == 14))			\
+		? (((1) << MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT1_GF_13_14)	\
+		: 0						\
+	)
+
 #define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE		0
 #define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE		\
 			(0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE)
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
index 01cc570..4f8857f 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
@@ -237,6 +237,7 @@ int bch_set_geometry(struct gpmi_nand_data *this)
 	unsigned int metadata_size;
 	unsigned int ecc_strength;
 	unsigned int page_size;
+	unsigned int gf_len;
 	int ret;
 
 	if (common_nfc_set_geometry(this))
@@ -247,6 +248,7 @@ int bch_set_geometry(struct gpmi_nand_data *this)
 	metadata_size = bch_geo->metadata_size;
 	ecc_strength  = bch_geo->ecc_strength >> 1;
 	page_size     = bch_geo->page_size;
+	gf_len        = bch_geo->gf_len;
 
 	ret = gpmi_enable_clk(this);
 	if (ret)
@@ -268,11 +270,13 @@ int bch_set_geometry(struct gpmi_nand_data *this)
 	writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count)
 			| BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size)
 			| BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this)
+			| BF_BCH_FLASH0LAYOUT0_GF(gf_len, this)
 			| BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this),
 			r->bch_regs + HW_BCH_FLASH0LAYOUT0);
 
 	writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size)
 			| BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this)
+			| BF_BCH_FLASH0LAYOUT1_GF(gf_len, this)
 			| BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this),
 			r->bch_regs + HW_BCH_FLASH0LAYOUT1);
 
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
index 38c8b8b..2521678 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
@@ -112,10 +112,12 @@ int common_nfc_set_geometry(struct gpmi_nand_data *this)
 	/* The default for the length of Galois Field. */
 	geo->gf_len = 13;
 
-	/* The default for chunk size. There is no oobsize greater then 512. */
+	/* The default for chunk size. */
 	geo->ecc_chunk_size = 512;
-	while (geo->ecc_chunk_size < mtd->oobsize)
+	while (geo->ecc_chunk_size < mtd->oobsize) {
 		geo->ecc_chunk_size *= 2; /* keep C >= O */
+		geo->gf_len = 14;
+	}
 
 	geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size;
 
-- 
1.7.0.4

             reply	other threads:[~2013-01-25  6:04 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-01-25  6:04 Huang Shijie [this message]
2013-01-25  6:04 ` [PATCH 2/2] mtd: gpmi: add sanity check for the ECC strength Huang Shijie
2013-01-29  1:23   ` [PATCH v2] mtd: gpmi: add sanity check for the ECC Huang Shijie
2013-02-04  8:31 ` [PATCH 1/2] mtd: gpmi: set the Golois Field bit for mx6q's BCH Artem Bityutskiy
2013-02-04  9:11   ` Huang Shijie

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1359093848-22301-1-git-send-email-b32955@freescale.com \
    --to=b32955@freescale.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).