From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2] rtc: rtc-mv: Add support for clk to avoid lockups
Date: Sun, 3 Feb 2013 12:32:06 +0100 [thread overview]
Message-ID: <1359891126-21909-1-git-send-email-andrew@lunn.ch> (raw)
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz gmbnomis at gmail.com
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
Since v1:
Enable clock before accessing RTC registers.
arch/arm/boot/dts/kirkwood.dtsi | 1 +
drivers/rtc/rtc-mv.c | 28 ++++++++++++++++++++++++----
2 files changed, 25 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 6c5d75f..c57b9c6 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -77,6 +77,7 @@
compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
reg = <0x10300 0x20>;
interrupts = <53>;
+ clocks = <&gate_clk 7>;
};
spi at 10600 {
diff --git a/drivers/rtc/rtc-mv.c b/drivers/rtc/rtc-mv.c
index 57233c8..8f87fec 100644
--- a/drivers/rtc/rtc-mv.c
+++ b/drivers/rtc/rtc-mv.c
@@ -14,6 +14,7 @@
#include <linux/platform_device.h>
#include <linux/of.h>
#include <linux/delay.h>
+#include <linux/clk.h>
#include <linux/gfp.h>
#include <linux/module.h>
@@ -41,6 +42,7 @@ struct rtc_plat_data {
struct rtc_device *rtc;
void __iomem *ioaddr;
int irq;
+ struct clk *clk;
};
static int mv_rtc_set_time(struct device *dev, struct rtc_time *tm)
@@ -221,6 +223,7 @@ static int mv_rtc_probe(struct platform_device *pdev)
struct rtc_plat_data *pdata;
resource_size_t size;
u32 rtc_time;
+ int ret = 0;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res)
@@ -239,11 +242,17 @@ static int mv_rtc_probe(struct platform_device *pdev)
if (!pdata->ioaddr)
return -ENOMEM;
+ pdata->clk = devm_clk_get(&pdev->dev, NULL);
+ /* Not all SoCs require a clock.*/
+ if (!IS_ERR(pdata->clk))
+ clk_prepare_enable(pdata->clk);
+
/* make sure the 24 hours mode is enabled */
rtc_time = readl(pdata->ioaddr + RTC_TIME_REG_OFFS);
if (rtc_time & RTC_HOURS_12H_MODE) {
dev_err(&pdev->dev, "24 Hours mode not supported.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
/* make sure it is actually functional */
@@ -252,7 +261,8 @@ static int mv_rtc_probe(struct platform_device *pdev)
rtc_time = readl(pdata->ioaddr + RTC_TIME_REG_OFFS);
if (rtc_time == 0x01000000) {
dev_err(&pdev->dev, "internal RTC not ticking\n");
- return -ENODEV;
+ ret = -ENODEV;
+ goto out;
}
}
@@ -268,8 +278,10 @@ static int mv_rtc_probe(struct platform_device *pdev)
} else
pdata->rtc = rtc_device_register(pdev->name, &pdev->dev,
&mv_rtc_ops, THIS_MODULE);
- if (IS_ERR(pdata->rtc))
- return PTR_ERR(pdata->rtc);
+ if (IS_ERR(pdata->rtc)) {
+ ret = PTR_ERR(pdata->rtc);
+ goto out;
+ }
if (pdata->irq >= 0) {
writel(0, pdata->ioaddr + RTC_ALARM_INTERRUPT_MASK_REG_OFFS);
@@ -282,6 +294,11 @@ static int mv_rtc_probe(struct platform_device *pdev)
}
return 0;
+out:
+ if (!IS_ERR(pdata->clk))
+ clk_disable_unprepare(pdata->clk);
+
+ return ret;
}
static int __exit mv_rtc_remove(struct platform_device *pdev)
@@ -292,6 +309,9 @@ static int __exit mv_rtc_remove(struct platform_device *pdev)
device_init_wakeup(&pdev->dev, 0);
rtc_device_unregister(pdata->rtc);
+ if (!IS_ERR(pdata->clk))
+ clk_disable_unprepare(pdata->clk);
+
return 0;
}
--
1.7.10.4
next reply other threads:[~2013-02-03 11:32 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-03 11:32 Andrew Lunn [this message]
2013-02-03 19:44 ` [PATCH v2] rtc: rtc-mv: Add support for clk to avoid lockups Simon Baatz
2013-02-03 22:14 ` Jason Cooper
2013-02-04 1:50 ` Jason Cooper
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1359891126-21909-1-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox