From: nicolas.ferre@atmel.com (Nicolas Ferre)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: at91: add Acme Systems Aria G25 board
Date: Mon, 25 Mar 2013 09:49:29 +0100 [thread overview]
Message-ID: <1364201369-12047-1-git-send-email-nicolas.ferre@atmel.com> (raw)
From: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/ariag25.dts | 168 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 168 insertions(+)
create mode 100644 arch/arm/boot/dts/ariag25.dts
diff --git a/arch/arm/boot/dts/ariag25.dts b/arch/arm/boot/dts/ariag25.dts
new file mode 100644
index 0000000..d18ef50
--- /dev/null
+++ b/arch/arm/boot/dts/ariag25.dts
@@ -0,0 +1,168 @@
+/*
+ * ariag25.dts - Device Tree file for Acme Systems Aria G25 (AT91SAM9G25 based)
+ *
+ * Copyright (C) 2013 Douglas Gilbert <dgilbert@interlog.com>,
+ * Robert Nelson <robertcnelson@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+/include/ "at91sam9g25.dtsi"
+
+/ {
+ model = "Acme Systems Aria G25";
+ compatible = "acme,ariag25", "atmel,at91sam9g25ek", "atmel,at91sam9x5ek",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+
+ aliases {
+ serial4 = &usart3;
+ serial5 = &uart0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
+ };
+
+ memory {
+ /* 128 MB, change this for 256 MB revision */
+ reg = <0x20000000 0x8000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock at 0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc at f0008000 {
+ /* N.B. Aria has no SD card detect (CD), assumed present */
+
+ pinctrl-0 = <
+ &pinctrl_mmc0_slot0_clk_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot at 0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+ };
+
+ i2c0: i2c at f8010000 {
+ status = "okay";
+ };
+
+ i2c1: i2c at f8014000 {
+ status = "okay";
+ };
+
+ /* TWD2+TCLK2 hidden behind ethernet, so no i2c2 */
+
+ usart0: serial at f801c000 {
+ pinctrl-0 = <&pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts>;
+ status = "okay";
+ };
+
+ usart1: serial at f8020000 {
+ pinctrl-0 = <&pinctrl_usart1
+ /* &pinctrl_usart1_rts */
+ /* &pinctrl_usart1_cts */
+ >;
+ status = "okay";
+ };
+
+ usart2: serial at f8024000 {
+ /* cannot activate RTS2+CTS2, clash with
+ * ethernet on PB0 and PB1 */
+ pinctrl-0 = <&pinctrl_usart2>;
+ status = "okay";
+ };
+
+ usart3: serial at f8028000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8028000 0x200>;
+ interrupts = <8 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3
+ /* &pinctrl_usart3_rts */
+ /* &pinctrl_usart3_cts */
+ >;
+ status = "okay";
+ };
+
+ macb0: ethernet at f802c000 {
+ phy-mode = "rmii";
+ /* following can be overwritten by uboot 'ftd set' command */
+ local-mac-address = [00 04 25 dd 10 01];
+ status = "okay";
+ };
+
+ uart0: serial at f8040000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8040000 0x200>;
+ interrupts = <15 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ status = "okay";
+ };
+
+ adc0: adc at f804c000 {
+ status = "okay";
+ atmel,adc-channels-used = <0xf>;
+ atmel,adc-num-channels = <4>;
+ };
+
+ dbgu: serial at fffff200 {
+ status = "okay";
+ };
+
+ pinctrl at fffff400 {
+ w1_0 {
+ pinctrl_w1_0: w1_0-0 {
+ atmel,pins = <0 21 0x0 0x1>; /* PA21 PIO, pull-up */
+ };
+ };
+ };
+
+ rtc at fffffeb0 {
+ status = "okay";
+ };
+ };
+
+ usb0: ohci at 00600000 {
+ status = "okay";
+ num-ports = <3>;
+ };
+
+ usb1: ehci at 00700000 {
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ /* little green LED in middle of Aria G25 module */
+ aria_led {
+ label = "aria_led";
+ gpios = <&pioB 8 0>; /* PB8 */
+ linux,default-trigger = "heartbeat";
+ };
+
+ };
+
+ onewire at 0 {
+ compatible = "w1-gpio";
+ gpios = <&pioA 21 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_w1_0>;
+ };
+};
--
1.8.0
next reply other threads:[~2013-03-25 8:49 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-25 8:49 Nicolas Ferre [this message]
2013-03-25 12:22 ` [PATCH] ARM: at91: add Acme Systems Aria G25 board Jean-Christophe PLAGNIOL-VILLARD
2013-03-25 12:33 ` Douglas Gilbert
2013-03-25 13:48 ` Douglas Gilbert
2013-03-25 14:10 ` Nicolas Ferre
2013-03-25 14:31 ` Jean-Christophe PLAGNIOL-VILLARD
2013-03-25 15:23 ` Douglas Gilbert
2013-03-25 17:04 ` Jean-Christophe PLAGNIOL-VILLARD
2013-03-25 14:11 ` Nicolas Ferre
2013-03-25 14:34 ` Jean-Christophe PLAGNIOL-VILLARD
2013-03-26 11:39 ` [PATCH v2] " Nicolas Ferre
2013-04-02 18:48 ` Olof Johansson
2013-04-03 19:10 ` Douglas Gilbert
2013-04-04 15:29 ` Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1364201369-12047-1-git-send-email-nicolas.ferre@atmel.com \
--to=nicolas.ferre@atmel.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).