From: rnayak@ti.com (Rajendra Nayak)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 1/6] ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
Date: Wed, 15 May 2013 20:18:37 +0530 [thread overview]
Message-ID: <1368629322-3170-2-git-send-email-rnayak@ti.com> (raw)
In-Reply-To: <1368629322-3170-1-git-send-email-rnayak@ti.com>
_enable_sysc() and _idle_sysc() handle the midle mode programming correctly
and program HWMOD_IDLEMODE_SMART or HWMOD_IDLEMODE_SMART_WKUP respectively
for supported IPs (The ones which support hardware controlled midle modes)
However the same programming logic is missing when it comes to sidle mode
programming. Here they seem to just set HWMOD_IDLEMODE_SMART (Again for the
ones which support hardware controlled sidle modes)
This problem was hidden due to the fact that a call to _enable_wakeup()
in those same functions would overwrite the idlemodes and program them
correctly (to HWMOD_IDLEMODE_SMART_WKUP in the supported cases)
So fix the sidlemode handling correctly in these functions and handle the
_enable_wakeup() for SIDLEMODE supported IPs same as the way its handled
for MIDLEMODE supported ones.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
---
arch/arm/mach-omap2/omap_hwmod.c | 42 +++++++++++++++++++++++---------------
1 file changed, 25 insertions(+), 17 deletions(-)
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index d25a95f..c28552b 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -1356,13 +1356,26 @@ static void _enable_sysc(struct omap_hwmod *oh)
clkdm = _get_clkdm(oh);
if (sf & SYSC_HAS_SIDLEMODE) {
+ if (oh->flags & HWMOD_SWSUP_SIDLE) {
+ idlemode = HWMOD_IDLEMODE_NO;
+ } else {
+ if (sf & SYSC_HAS_ENAWAKEUP)
+ _enable_wakeup(oh, &v);
+ if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+ idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
+ }
+
+ /*
+ * This is special handling for some IPs like
+ * 32k sync timer. Force them to idle!
+ */
clkdm_act = (clkdm && clkdm->flags & CLKDM_ACTIVE_WITH_MPU);
if (clkdm_act && !(oh->class->sysc->idlemodes &
(SIDLE_SMART | SIDLE_SMART_WKUP)))
idlemode = HWMOD_IDLEMODE_FORCE;
- else
- idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
- HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
+
_set_slave_idlemode(oh, idlemode, &v);
}
@@ -1391,10 +1404,6 @@ static void _enable_sysc(struct omap_hwmod *oh)
(sf & SYSC_HAS_CLOCKACTIVITY))
_set_clockactivity(oh, oh->class->sysc->clockact, &v);
- /* If slave is in SMARTIDLE, also enable wakeup */
- if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
- _enable_wakeup(oh, &v);
-
_write_sysconfig(v, oh);
/*
@@ -1430,13 +1439,16 @@ static void _idle_sysc(struct omap_hwmod *oh)
sf = oh->class->sysc->sysc_flags;
if (sf & SYSC_HAS_SIDLEMODE) {
- /* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */
- if (oh->flags & HWMOD_SWSUP_SIDLE ||
- !(oh->class->sysc->idlemodes &
- (SIDLE_SMART | SIDLE_SMART_WKUP)))
+ if (oh->flags & HWMOD_SWSUP_SIDLE) {
idlemode = HWMOD_IDLEMODE_FORCE;
- else
- idlemode = HWMOD_IDLEMODE_SMART;
+ } else {
+ if (sf & SYSC_HAS_ENAWAKEUP)
+ _enable_wakeup(oh, &v);
+ if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+ idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
+ }
_set_slave_idlemode(oh, idlemode, &v);
}
@@ -1455,10 +1467,6 @@ static void _idle_sysc(struct omap_hwmod *oh)
_set_master_standbymode(oh, idlemode, &v);
}
- /* If slave is in SMARTIDLE, also enable wakeup */
- if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
- _enable_wakeup(oh, &v);
-
_write_sysconfig(v, oh);
}
--
1.7.9.5
next prev parent reply other threads:[~2013-05-15 14:48 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-15 14:48 [PATCH v3 0/6] ARM: OMAP2+: hwmod and SERIAL: Remove sysc handling from driver Rajendra Nayak
2013-05-15 14:48 ` Rajendra Nayak [this message]
2013-05-15 14:48 ` [PATCH v3 2/6] ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active Rajendra Nayak
2013-05-15 14:48 ` [PATCH v3 3/6] ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes Rajendra Nayak
2013-05-15 14:48 ` [PATCH v3 4/6] ARM: OMAP2+: serial: Remove the un-used slave idle hooks Rajendra Nayak
2013-05-15 14:48 ` [PATCH v3 5/6] SERIAL: OMAP: Remove the slave idle handling from the driver Rajendra Nayak
2013-05-15 14:48 ` [PATCH v3 6/6] ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis Rajendra Nayak
2013-05-16 18:32 ` [PATCH v3 0/6] ARM: OMAP2+: hwmod and SERIAL: Remove sysc handling from driver Paul Walmsley
2013-05-17 14:29 ` Kevin Hilman
2013-05-19 23:07 ` Paul Walmsley
2013-05-20 5:42 ` Rajendra Nayak
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1368629322-3170-2-git-send-email-rnayak@ti.com \
--to=rnayak@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).