[RESEND][PATCH 1/2] clk: wm831x: Fix update wrong register for enable/disable FLL

[RESEND][PATCH 1/2] clk: wm831x: Fix update wrong register for enable/disable FLL

[Axel Lin]

According to the datasheet, FLL Enable is controlled by
R16530 (4092h) FLL Control1
        BIT 0: FLL Enable
                0 = Disable
                1 = Enable

Thus the code should update WM831X_FLL_CONTROL_1 register rather than
WM831X_FLL_CONTROL_2 register.

Also fixes a trivial typo in dev_crit message.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
Hi Mike,
This patch serial was sent on http://lkml.org/lkml/2013/5/1/152
With Mark's Ack.

Regards,
Axel
 drivers/clk/clk-wm831x.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/clk-wm831x.c b/drivers/clk/clk-wm831x.c
index 16ed068..4bdf0b0 100644
--- a/drivers/clk/clk-wm831x.c
+++ b/drivers/clk/clk-wm831x.c
@@ -97,7 +97,7 @@ static int wm831x_fll_prepare(struct clk_hw *hw)
 	struct wm831x *wm831x = clkdata->wm831x;
 	int ret;
 
-	ret = wm831x_set_bits(wm831x, WM831X_FLL_CONTROL_2,
+	ret = wm831x_set_bits(wm831x, WM831X_FLL_CONTROL_1,
 			      WM831X_FLL_ENA, WM831X_FLL_ENA);
 	if (ret != 0)
 		dev_crit(wm831x->dev, "Failed to enable FLL: %d\n", ret);
@@ -114,9 +114,9 @@ static void wm831x_fll_unprepare(struct clk_hw *hw)
 	struct wm831x *wm831x = clkdata->wm831x;
 	int ret;
 
-	ret = wm831x_set_bits(wm831x, WM831X_FLL_CONTROL_2, WM831X_FLL_ENA, 0);
+	ret = wm831x_set_bits(wm831x, WM831X_FLL_CONTROL_1, WM831X_FLL_ENA, 0);
 	if (ret != 0)
-		dev_crit(wm831x->dev, "Failed to disaable FLL: %d\n", ret);
+		dev_crit(wm831x->dev, "Failed to disable FLL: %d\n", ret);
 }
 
 static unsigned long wm831x_fll_recalc_rate(struct clk_hw *hw,
-- 
1.8.1.2

[RESEND][PATCH 2/2] clk: wm831x: Fix wm831x_clkout_get_parent

[Axel Lin]

Current code looks strange because calling wm831x_clkout_set_parent() with 0 as
parent parameter, wm831x_clkout_get_parent() will return 1.

According to the datasheet:
R16528 (4090h) Clock Control1
        BIT 0: CLKOUT output source select
                0 = FLL output
                1 = 32.768kHz oscillator

Thus fix the entry order in wm831x_clkout_parents[] to make it has
the same meaning as the datasheet and make the return value
of wm831x_clkout_get_parent() consistent with the parent pass to
wm831x_clkout_set_parent().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 drivers/clk/clk-wm831x.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/clk-wm831x.c b/drivers/clk/clk-wm831x.c
index 4bdf0b0..58d08a6 100644
--- a/drivers/clk/clk-wm831x.c
+++ b/drivers/clk/clk-wm831x.c
@@ -299,8 +299,8 @@ static void wm831x_clkout_unprepare(struct clk_hw *hw)
 }
 
 static const char *wm831x_clkout_parents[] = {
-	"xtal",
 	"fll",
+	"xtal",
 };
 
 static u8 wm831x_clkout_get_parent(struct clk_hw *hw)
@@ -318,9 +318,9 @@ static u8 wm831x_clkout_get_parent(struct clk_hw *hw)
 	}
 
 	if (ret & WM831X_CLKOUT_SRC)
-		return 0;
-	else
 		return 1;
+	else
+		return 0;
 }
 
 static int wm831x_clkout_set_parent(struct clk_hw *hw, u8 parent)
-- 
1.8.1.2