From mboxrd@z Thu Jan 1 00:00:00 1970 From: ezequiel.garcia@free-electrons.com (Ezequiel Garcia) Date: Fri, 7 Jun 2013 13:47:51 -0300 Subject: [PATCH 14/14] ARM: mvebu: Relocate Armada XP PCIe device tree nodes In-Reply-To: <1370623671-7748-1-git-send-email-ezequiel.garcia@free-electrons.com> References: <1370623671-7748-1-git-send-email-ezequiel.garcia@free-electrons.com> Message-ID: <1370623671-7748-15-git-send-email-ezequiel.garcia@free-electrons.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Now that mbus has been added to the device tree, it's possible to move the PCIe nodes out of internal registers, placing it directly below the mbus. This is a more accurate representation of the hardware. Signed-off-by: Ezequiel Garcia --- arch/arm/boot/dts/armada-xp-db.dts | 66 ++-- arch/arm/boot/dts/armada-xp-gp.dts | 42 +-- arch/arm/boot/dts/armada-xp-mv78230.dtsi | 209 ++++++------- arch/arm/boot/dts/armada-xp-mv78260.dtsi | 245 +++++++-------- arch/arm/boot/dts/armada-xp-mv78460.dtsi | 377 ++++++++++++----------- arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 18 +- 6 files changed, 480 insertions(+), 477 deletions(-) diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts index d6cc8bf..32e25fe 100644 --- a/arch/arm/boot/dts/armada-xp-db.dts +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -30,6 +30,39 @@ }; soc { + pcie-controller { + status = "okay"; + + /* + * All 6 slots are physically present as + * standard PCIe slots on the board. + */ + pcie at 1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie at 2,0 { + /* Port 0, Lane 1 */ + status = "okay"; + }; + pcie at 3,0 { + /* Port 0, Lane 2 */ + status = "okay"; + }; + pcie at 4,0 { + /* Port 0, Lane 3 */ + status = "okay"; + }; + pcie at 9,0 { + /* Port 2, Lane 0 */ + status = "okay"; + }; + pcie at 10,0 { + /* Port 3, Lane 0 */ + status = "okay"; + }; + }; + internal-regs { serial at 12000 { clock-frequency = <250000000>; @@ -122,39 +155,6 @@ spi-max-frequency = <20000000>; }; }; - - pcie-controller { - status = "okay"; - - /* - * All 6 slots are physically present as - * standard PCIe slots on the board. - */ - pcie at 1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - pcie at 2,0 { - /* Port 0, Lane 1 */ - status = "okay"; - }; - pcie at 3,0 { - /* Port 0, Lane 2 */ - status = "okay"; - }; - pcie at 4,0 { - /* Port 0, Lane 3 */ - status = "okay"; - }; - pcie at 9,0 { - /* Port 2, Lane 0 */ - status = "okay"; - }; - pcie at 10,0 { - /* Port 3, Lane 0 */ - status = "okay"; - }; - }; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index d045d6e..333dd3b 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -68,6 +68,27 @@ }; }; + pcie-controller { + status = "okay"; + + /* + * The 3 slots are physically present as + * standard PCIe slots on the board. + */ + pcie at 1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie at 9,0 { + /* Port 2, Lane 0 */ + status = "okay"; + }; + pcie at 10,0 { + /* Port 3, Lane 0 */ + status = "okay"; + }; + }; + internal-regs { serial at 12000 { clock-frequency = <250000000>; @@ -141,27 +162,6 @@ spi-max-frequency = <108000000>; }; }; - - pcie-controller { - status = "okay"; - - /* - * The 3 slots are physically present as - * standard PCIe slots on the board. - */ - pcie at 1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - pcie at 9,0 { - /* Port 2, Lane 0 */ - status = "okay"; - }; - pcie at 10,0 { - /* Port 3, Lane 0 */ - status = "okay"; - }; - }; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi index f8eaa38..e0265e5 100644 --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi @@ -44,6 +44,111 @@ }; soc { + /* + * MV78230 has 2 PCIe units Gen2.0: One unit can be + * configured as x4 or quad x1 lanes. One unit is + * x4/x1. + */ + pcie-controller { + compatible = "marvell,armada-xp-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x40000 0 0x40000 0 0x00002000 /* Port 0.0 registers */ + 0x82000000 0 0x42000 0 0x42000 0 0x00002000 /* Port 2.0 registers */ + 0x82000000 0 0x44000 0 0x44000 0 0x00002000 /* Port 0.1 registers */ + 0x82000000 0 0x48000 0 0x48000 0 0x00002000 /* Port 0.2 registers */ + 0x82000000 0 0x4c000 0 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0xe0000000 0xffff0000 0xe0000000 0 0x08000000 /* non-prefetchable memory */ + 0x81000000 0 0 0xffff0000 0xe8000000 0 0x00100000>; /* downstream I/O */ + + pcie at 1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 58>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + pcie at 2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 59>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + pcie at 3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 60>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + + pcie at 4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 61>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + pcie at 9,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 26>; + status = "disabled"; + }; + }; + internal-regs { pinctrl { compatible = "marvell,mv78230-pinctrl"; @@ -77,110 +182,6 @@ #interrupts-cells = <2>; interrupts = <87>, <88>, <89>; }; - - /* - * MV78230 has 2 PCIe units Gen2.0: One unit can be - * configured as x4 or quad x1 lanes. One unit is - * x4/x1. - */ - pcie-controller { - compatible = "marvell,armada-xp-pcie"; - status = "disabled"; - device_type = "pci"; - -#address-cells = <3>; -#size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */ - 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */ - 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */ - 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */ - 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */ - 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */ - 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */ - - pcie at 1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 58>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 5>; - status = "disabled"; - }; - - pcie at 2,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; - reg = <0x1000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 59>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <1>; - clocks = <&gateclk 6>; - status = "disabled"; - }; - - pcie at 3,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; - reg = <0x1800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 60>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <2>; - clocks = <&gateclk 7>; - status = "disabled"; - }; - - pcie at 4,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>; - reg = <0x2000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 61>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <3>; - clocks = <&gateclk 8>; - status = "disabled"; - }; - - pcie at 9,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; - status = "disabled"; - }; - }; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index f4029f0..f2bb74b 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -45,6 +45,129 @@ }; soc { + /* + * MV78260 has 3 PCIe units Gen2.0: Two units can be + * configured as x4 or quad x1 lanes. One unit is + * x4/x1. + */ + pcie-controller { + compatible = "marvell,armada-xp-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x40000 0 0x40000 0 0x00002000 /* Port 0.0 registers */ + 0x82000000 0 0x42000 0 0x42000 0 0x00002000 /* Port 2.0 registers */ + 0x82000000 0 0x44000 0 0x44000 0 0x00002000 /* Port 0.1 registers */ + 0x82000000 0 0x48000 0 0x48000 0 0x00002000 /* Port 0.2 registers */ + 0x82000000 0 0x4c000 0 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 0 0x80000 0 0x00002000 /* Port 1.0 registers */ + 0x82000000 0 0x82000 0 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0xe0000000 0xffff0000 0xe0000000 0 0x08000000 /* non-prefetchable memory */ + 0x81000000 0 0 0xffff0000 0xe8000000 0 0x00100000>; /* downstream I/O */ + + pcie at 1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 58>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + pcie at 2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 59>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + pcie at 3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 60>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + + pcie at 4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 61>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + pcie at 9,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 26>; + status = "disabled"; + }; + + pcie at 10,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x82000 0 0x2000>; + reg = <0x5000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 103>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 27>; + status = "disabled"; + }; + }; + internal-regs { pinctrl { compatible = "marvell,mv78260-pinctrl"; @@ -97,128 +220,6 @@ clocks = <&gateclk 1>; status = "disabled"; }; - - /* - * MV78260 has 3 PCIe units Gen2.0: Two units can be - * configured as x4 or quad x1 lanes. One unit is - * x4/x1. - */ - pcie-controller { - compatible = "marvell,armada-xp-pcie"; - status = "disabled"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */ - 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */ - 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */ - 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */ - 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */ - 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */ - 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */ - 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */ - 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */ - - pcie at 1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 58>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 5>; - status = "disabled"; - }; - - pcie at 2,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; - reg = <0x1000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 59>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <1>; - clocks = <&gateclk 6>; - status = "disabled"; - }; - - pcie at 3,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; - reg = <0x1800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 60>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <2>; - clocks = <&gateclk 7>; - status = "disabled"; - }; - - pcie at 4,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>; - reg = <0x2000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 61>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <3>; - clocks = <&gateclk 8>; - status = "disabled"; - }; - - pcie at 9,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; - status = "disabled"; - }; - - pcie at 10,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x82000 0 0x2000>; - reg = <0x5000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 103>; - marvell,pcie-port = <3>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 27>; - status = "disabled"; - }; - }; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi index 488ca5e..21376c8 100644 --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi @@ -60,6 +60,195 @@ }; soc { + /* + * MV78460 has 4 PCIe units Gen2.0: Two units can be + * configured as x4 or quad x1 lanes. Two units are + * x4/x1. + */ + pcie-controller { + compatible = "marvell,armada-xp-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x40000 0 0x40000 0 0x00002000 /* Port 0.0 registers */ + 0x82000000 0 0x42000 0 0x42000 0 0x00002000 /* Port 2.0 registers */ + 0x82000000 0 0x44000 0 0x44000 0 0x00002000 /* Port 0.1 registers */ + 0x82000000 0 0x48000 0 0x48000 0 0x00002000 /* Port 0.2 registers */ + 0x82000000 0 0x4c000 0 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 0 0x80000 0 0x00002000 /* Port 1.0 registers */ + 0x82000000 0 0x82000 0 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0x84000 0 0x84000 0 0x00002000 /* Port 1.1 registers */ + 0x82000000 0 0x88000 0 0x88000 0 0x00002000 /* Port 1.2 registers */ + 0x82000000 0 0x8c000 0 0x8c000 0 0x00002000 /* Port 1.3 registers */ + 0x82000000 0 0xe0000000 0xffff0000 0xe0000000 0 0x08000000 /* non-prefetchable memory */ + 0x81000000 0 0 0xffff0000 0xe8000000 0 0x00100000>; /* downstream I/O */ + + pcie at 1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 58>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + pcie at 2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 59>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + pcie at 3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 60>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + + pcie at 4,0 { + device_type = "pci"; + assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 61>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + pcie at 5,0 { + device_type = "pci"; + assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 9>; + status = "disabled"; + }; + + pcie at 6,0 { + device_type = "pci"; + assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; + reg = <0x3000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 63>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 10>; + status = "disabled"; + }; + + pcie at 7,0 { + device_type = "pci"; + assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; + reg = <0x3800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 64>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 11>; + status = "disabled"; + }; + + pcie at 8,0 { + device_type = "pci"; + assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; + reg = <0x4000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 65>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 12>; + status = "disabled"; + }; + pcie at 9,0 { + device_type = "pci"; + assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 26>; + status = "disabled"; + }; + + pcie at 10,0 { + device_type = "pci"; + assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; + reg = <0x5000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 103>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 27>; + status = "disabled"; + }; + }; + internal-regs { pinctrl { compatible = "marvell,mv78460-pinctrl"; @@ -112,194 +301,6 @@ clocks = <&gateclk 1>; status = "disabled"; }; - - /* - * MV78460 has 4 PCIe units Gen2.0: Two units can be - * configured as x4 or quad x1 lanes. Two units are - * x4/x1. - */ - pcie-controller { - compatible = "marvell,armada-xp-pcie"; - status = "disabled"; - device_type = "pci"; - - #address-cells = <3>; - #size-cells = <2>; - - bus-range = <0x00 0xff>; - - ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */ - 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */ - 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */ - 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */ - 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */ - 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */ - 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */ - 0x82000000 0 0x84000 0x84000 0 0x00002000 /* Port 1.1 registers */ - 0x82000000 0 0x88000 0x88000 0 0x00002000 /* Port 1.2 registers */ - 0x82000000 0 0x8c000 0x8c000 0 0x00002000 /* Port 1.3 registers */ - 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */ - 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */ - - pcie at 1,0 { - device_type = "pci"; - assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 58>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 5>; - status = "disabled"; - }; - - pcie at 2,0 { - device_type = "pci"; - assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; - reg = <0x1000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 59>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <1>; - clocks = <&gateclk 6>; - status = "disabled"; - }; - - pcie at 3,0 { - device_type = "pci"; - assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; - reg = <0x1800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 60>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <2>; - clocks = <&gateclk 7>; - status = "disabled"; - }; - - pcie at 4,0 { - device_type = "pci"; - assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; - reg = <0x2000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 61>; - marvell,pcie-port = <0>; - marvell,pcie-lane = <3>; - clocks = <&gateclk 8>; - status = "disabled"; - }; - - pcie at 5,0 { - device_type = "pci"; - assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; - reg = <0x2800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 62>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 9>; - status = "disabled"; - }; - - pcie at 6,0 { - device_type = "pci"; - assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; - reg = <0x3000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 63>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <1>; - clocks = <&gateclk 10>; - status = "disabled"; - }; - - pcie at 7,0 { - device_type = "pci"; - assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; - reg = <0x3800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 64>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <2>; - clocks = <&gateclk 11>; - status = "disabled"; - }; - - pcie at 8,0 { - device_type = "pci"; - assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; - reg = <0x4000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 65>; - marvell,pcie-port = <1>; - marvell,pcie-lane = <3>; - clocks = <&gateclk 12>; - status = "disabled"; - }; - pcie at 9,0 { - device_type = "pci"; - assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; - reg = <0x4800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 99>; - marvell,pcie-port = <2>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 26>; - status = "disabled"; - }; - - pcie at 10,0 { - device_type = "pci"; - assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; - reg = <0x5000 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &mpic 103>; - marvell,pcie-port = <3>; - marvell,pcie-lane = <0>; - clocks = <&gateclk 27>; - status = "disabled"; - }; - }; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index a895e1b..d2cb11e 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -56,6 +56,15 @@ }; }; + pcie-controller { + status = "okay"; + /* Internal mini-PCIe connector */ + pcie at 1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + }; + internal-regs { serial at 12000 { clock-frequency = <250000000>; @@ -169,15 +178,6 @@ usb at 51000 { status = "okay"; }; - - pcie-controller { - status = "okay"; - /* Internal mini-PCIe connector */ - pcie at 1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - }; }; }; }; -- 1.8.1.5