From: sboyd@codeaurora.org (Stephen Boyd)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/4] msm_serial: Fix sparse warnings
Date: Wed, 24 Jul 2013 11:37:29 -0700 [thread overview]
Message-ID: <1374691051-28544-3-git-send-email-sboyd@codeaurora.org> (raw)
In-Reply-To: <1374691051-28544-1-git-send-email-sboyd@codeaurora.org>
drivers/tty/serial/msm_serial.c:302:6: warning: symbol 'msm_set_mctrl' was
not declared. Should it be static?
drivers/tty/serial/msm_serial.c:597:17: warning: incorrect type in argument 2
(different address spaces)
drivers/tty/serial/msm_serial.c:597:17: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:597:17: got unsigned int *
drivers/tty/serial/msm_serial.c:608:33: warning: incorrect type in argument 1
(different address spaces)
drivers/tty/serial/msm_serial.c:608:33: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:608:33: got unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: warning: incorrect type in assignment
(different address spaces)
drivers/tty/serial/msm_serial.c:648:37: expected unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: got void [noderef] <asn:2>*
Mark the ioremapped memory as __iomem and use writel instead of
iowrite because we're not dealing with PCI devices. Also, mark
msm_set_mctrl() static because it isn't used outside this file.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/tty/serial/msm_serial.c | 17 +++++++----------
1 file changed, 7 insertions(+), 10 deletions(-)
diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index fa3fc67..cab4105 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -45,7 +45,7 @@ struct msm_port {
struct clk *clk;
struct clk *pclk;
unsigned int imr;
- unsigned int *gsbi_base;
+ void __iomem *gsbi_base;
int is_uartdm;
unsigned int old_snap_state;
};
@@ -299,7 +299,7 @@ static void msm_reset(struct uart_port *port)
msm_write(port, UART_CR_CMD_SET_RFR, UART_CR);
}
-void msm_set_mctrl(struct uart_port *port, unsigned int mctrl)
+static void msm_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
unsigned int mr;
mr = msm_read(port, UART_MR1);
@@ -593,12 +593,10 @@ static void msm_release_port(struct uart_port *port)
port->membase = NULL;
if (msm_port->gsbi_base) {
- iowrite32(GSBI_PROTOCOL_IDLE, msm_port->gsbi_base +
- GSBI_CONTROL);
-
- gsbi_resource = platform_get_resource(pdev,
- IORESOURCE_MEM, 1);
+ writel_relaxed(GSBI_PROTOCOL_IDLE,
+ msm_port->gsbi_base + GSBI_CONTROL);
+ gsbi_resource = platform_get_resource(pdev, IORESOURCE_MEM, 1);
if (unlikely(!gsbi_resource))
return;
@@ -670,10 +668,9 @@ static void msm_config_port(struct uart_port *port, int flags)
if (ret)
return;
}
-
if (msm_port->is_uartdm)
- iowrite32(GSBI_PROTOCOL_UART, msm_port->gsbi_base +
- GSBI_CONTROL);
+ writel_relaxed(GSBI_PROTOCOL_UART,
+ msm_port->gsbi_base + GSBI_CONTROL);
}
static int msm_verify_port(struct uart_port *port, struct serial_struct *ser)
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
next prev parent reply other threads:[~2013-07-24 18:37 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-24 18:37 [PATCH 0/4] msm_serial fixes and improvements Stephen Boyd
2013-07-24 18:37 ` [PATCH 1/4] msm_serial: Fix NUL byte output on UARTDM Stephen Boyd
2013-07-24 20:29 ` David Brown
2013-07-24 18:37 ` Stephen Boyd [this message]
2013-07-24 20:30 ` [PATCH 2/4] msm_serial: Fix sparse warnings David Brown
2013-07-24 18:37 ` [PATCH 3/4] msm_serial: Make baud_code detection more dynamic Stephen Boyd
2013-07-24 20:30 ` David Brown
2013-07-26 4:30 ` Bjorn Andersson
2013-07-26 17:05 ` Stephen Boyd
2013-07-24 18:37 ` [PATCH 4/4] msm_serial: Send more than 1 character at a time on UARTDM Stephen Boyd
2013-07-24 20:31 ` David Brown
2013-07-24 20:31 ` [PATCH 0/4] msm_serial fixes and improvements David Brown
2013-07-29 9:31 ` Ivan T. Ivanov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1374691051-28544-3-git-send-email-sboyd@codeaurora.org \
--to=sboyd@codeaurora.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).