From: zonque@gmail.com (Daniel Mack)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 08/20] mmc: host: pxamci: switch over to dmaengine use
Date: Wed, 7 Aug 2013 17:33:57 +0200 [thread overview]
Message-ID: <1375889649-14638-9-git-send-email-zonque@gmail.com> (raw)
In-Reply-To: <1375889649-14638-1-git-send-email-zonque@gmail.com>
Successfully testes on a PXA3xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
---
drivers/mmc/host/pxamci.c | 188 +++++++++++++++++++++++++---------------------
1 file changed, 102 insertions(+), 86 deletions(-)
diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 2c5a91b..7aa97eb 100644
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -22,7 +22,9 @@
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
+#include <linux/dma/mmp-pdma.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/mmc/host.h>
@@ -37,7 +39,6 @@
#include <asm/sizes.h>
#include <mach/hardware.h>
-#include <mach/dma.h>
#include <linux/platform_data/mmc-pxamci.h>
#include "pxamci.h"
@@ -58,7 +59,6 @@ struct pxamci_host {
struct clk *clk;
unsigned long clkrate;
int irq;
- int dma;
unsigned int clkrt;
unsigned int cmdat;
unsigned int imask;
@@ -69,8 +69,10 @@ struct pxamci_host {
struct mmc_command *cmd;
struct mmc_data *data;
+ struct dma_chan *dma_chan_rx;
+ struct dma_chan *dma_chan_tx;
+ dma_cookie_t dma_cookie;
dma_addr_t sg_dma;
- struct pxa_dma_desc *sg_cpu;
unsigned int dma_len;
unsigned int dma_dir;
@@ -173,14 +175,18 @@ static void pxamci_disable_irq(struct pxamci_host *host, unsigned int mask)
spin_unlock_irqrestore(&host->lock, flags);
}
+static void pxamci_dma_irq(void *param);
+
static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
{
+ struct dma_async_tx_descriptor *tx;
+ enum dma_data_direction direction;
+ struct dma_slave_config config;
+ struct dma_chan *chan;
unsigned int nob = data->blocks;
unsigned long long clks;
unsigned int timeout;
- bool dalgn = 0;
- u32 dcmd;
- int i;
+ int ret;
host->data = data;
@@ -195,54 +201,46 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
timeout = (unsigned int)clks + (data->timeout_clks << host->clkrt);
writel((timeout + 255) / 256, host->base + MMC_RDTO);
+ memset(&config, 0, sizeof(config));
+ config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ config.src_addr = host->res->start + MMC_RXFIFO;
+ config.dst_addr = host->res->start + MMC_TXFIFO;
+ config.src_maxburst = 32;
+ config.dst_maxburst = 32;
+
if (data->flags & MMC_DATA_READ) {
host->dma_dir = DMA_FROM_DEVICE;
- dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC;
- DRCMR(host->dma_drcmrtx) = 0;
- DRCMR(host->dma_drcmrrx) = host->dma | DRCMR_MAPVLD;
+ direction = DMA_DEV_TO_MEM;
+ chan = host->dma_chan_rx;
} else {
host->dma_dir = DMA_TO_DEVICE;
- dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG;
- DRCMR(host->dma_drcmrrx) = 0;
- DRCMR(host->dma_drcmrtx) = host->dma | DRCMR_MAPVLD;
+ direction = DMA_MEM_TO_DEV;
+ chan = host->dma_chan_tx;
}
- dcmd |= DCMD_BURST32 | DCMD_WIDTH1;
+ config.direction = direction;
+
+ ret = dmaengine_slave_config(chan, &config);
+ if (ret < 0) {
+ dev_err(mmc_dev(host->mmc), "dma slave config failed\n");
+ return;
+ }
- host->dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+ host->dma_len = dma_map_sg(chan->device->dev, data->sg, data->sg_len,
host->dma_dir);
- for (i = 0; i < host->dma_len; i++) {
- unsigned int length = sg_dma_len(&data->sg[i]);
- host->sg_cpu[i].dcmd = dcmd | length;
- if (length & 31 && !(data->flags & MMC_DATA_READ))
- host->sg_cpu[i].dcmd |= DCMD_ENDIRQEN;
- /* Not aligned to 8-byte boundary? */
- if (sg_dma_address(&data->sg[i]) & 0x7)
- dalgn = 1;
- if (data->flags & MMC_DATA_READ) {
- host->sg_cpu[i].dsadr = host->res->start + MMC_RXFIFO;
- host->sg_cpu[i].dtadr = sg_dma_address(&data->sg[i]);
- } else {
- host->sg_cpu[i].dsadr = sg_dma_address(&data->sg[i]);
- host->sg_cpu[i].dtadr = host->res->start + MMC_TXFIFO;
- }
- host->sg_cpu[i].ddadr = host->sg_dma + (i + 1) *
- sizeof(struct pxa_dma_desc);
+ tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!tx) {
+ dev_err(mmc_dev(host->mmc), "prep_slave_sg() failed\n");
+ return;
}
- host->sg_cpu[host->dma_len - 1].ddadr = DDADR_STOP;
- wmb();
- /*
- * The PXA27x DMA controller encounters overhead when working with
- * unaligned (to 8-byte boundaries) data, so switch on byte alignment
- * mode only if we have unaligned data.
- */
- if (dalgn)
- DALGN |= (1 << host->dma);
- else
- DALGN &= ~(1 << host->dma);
- DDADR(host->dma) = host->sg_dma;
+ tx->callback = pxamci_dma_irq;
+ tx->callback_param = host;
+
+ host->dma_cookie = dmaengine_submit(tx);
/*
* workaround for erratum #91:
@@ -251,7 +249,7 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
* before starting DMA.
*/
if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ)
- DCSR(host->dma) = DCSR_RUN;
+ dma_async_issue_pending(chan);
}
static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat)
@@ -343,7 +341,7 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat)
* enable DMA late
*/
if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE)
- DCSR(host->dma) = DCSR_RUN;
+ dma_async_issue_pending(host->dma_chan_tx);
} else {
pxamci_finish_request(host, host->mrq);
}
@@ -358,9 +356,8 @@ static int pxamci_data_done(struct pxamci_host *host, unsigned int stat)
if (!data)
return 0;
- DCSR(host->dma) = 0;
- dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
- host->dma_dir);
+ dma_unmap_sg(host->dma_chan_rx->device->dev,
+ data->sg, data->sg_len, host->dma_dir);
if (stat & STAT_READ_TIME_OUT)
data->error = -ETIMEDOUT;
@@ -552,17 +549,25 @@ static const struct mmc_host_ops pxamci_ops = {
.enable_sdio_irq = pxamci_enable_sdio_irq,
};
-static void pxamci_dma_irq(int dma, void *devid)
+static void pxamci_dma_irq(void *param)
{
- struct pxamci_host *host = devid;
- int dcsr = DCSR(dma);
- DCSR(dma) = dcsr & ~DCSR_STOPIRQEN;
+ struct pxamci_host *host = param;
+ struct dma_tx_state state;
+ enum dma_status status;
+ struct dma_chan *chan;
- if (dcsr & DCSR_ENDINTR) {
+ if (host->data->flags & MMC_DATA_READ)
+ chan = host->dma_chan_rx;
+ else
+ chan = host->dma_chan_tx;
+
+ status = dmaengine_tx_status(chan, host->dma_cookie, &state);
+
+ if (likely(status == DMA_SUCCESS)) {
writel(BUF_PART_FULL, host->base + MMC_PRTBUF);
} else {
- pr_err("%s: DMA error on channel %d (DCSR=%#x)\n",
- mmc_hostname(host->mmc), dma, dcsr);
+ pr_err("%s: DMA error on %s channel\n", mmc_hostname(host->mmc),
+ host->data->flags & MMC_DATA_READ ? "rx" : "tx");
host->data->error = -EIO;
pxamci_data_done(host, 0);
}
@@ -626,6 +631,7 @@ static int pxamci_probe(struct platform_device *pdev)
struct pxamci_host *host = NULL;
struct resource *r, *dmarx, *dmatx;
int ret, irq, gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
+ dma_cap_mask_t mask;
ret = pxamci_of_init(pdev);
if (ret)
@@ -671,7 +677,6 @@ static int pxamci_probe(struct platform_device *pdev)
host = mmc_priv(mmc);
host->mmc = mmc;
- host->dma = -1;
host->pdata = pdev->dev.platform_data;
host->clkrt = CLKRT_OFF;
@@ -702,12 +707,6 @@ static int pxamci_probe(struct platform_device *pdev)
MMC_CAP_SD_HIGHSPEED;
}
- host->sg_cpu = dma_alloc_coherent(&pdev->dev, PAGE_SIZE, &host->sg_dma, GFP_KERNEL);
- if (!host->sg_cpu) {
- ret = -ENOMEM;
- goto out;
- }
-
spin_lock_init(&host->lock);
host->res = r;
host->irq = irq;
@@ -728,32 +727,50 @@ static int pxamci_probe(struct platform_device *pdev)
writel(64, host->base + MMC_RESTO);
writel(host->imask, host->base + MMC_I_MASK);
- host->dma = pxa_request_dma(DRIVER_NAME, DMA_PRIO_LOW,
- pxamci_dma_irq, host);
- if (host->dma < 0) {
- ret = -EBUSY;
- goto out;
- }
-
ret = request_irq(host->irq, pxamci_irq, 0, DRIVER_NAME, host);
if (ret)
goto out;
platform_set_drvdata(pdev, mmc);
- dmarx = platform_get_resource(pdev, IORESOURCE_DMA, 0);
- if (!dmarx) {
- ret = -ENXIO;
+ if (!pdev->dev.of_node) {
+ dmarx = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (!dmarx) {
+ ret = -ENXIO;
+ goto out;
+ }
+ host->dma_drcmrrx = dmarx->start;
+
+ dmatx = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (!dmatx) {
+ ret = -ENXIO;
+ goto out;
+ }
+ host->dma_drcmrtx = dmatx->start;
+ }
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ host->dma_chan_rx =
+ dma_request_slave_channel_compat(mask, mmp_pdma_filter_fn,
+ &host->dma_drcmrrx,
+ &pdev->dev, "rx");
+ if (host->dma_chan_rx == NULL) {
+ dev_err(&pdev->dev, "unable to request rx dma channel\n");
+ ret = -ENODEV;
goto out;
}
- host->dma_drcmrrx = dmarx->start;
- dmatx = platform_get_resource(pdev, IORESOURCE_DMA, 1);
- if (!dmatx) {
- ret = -ENXIO;
+ host->dma_chan_tx =
+ dma_request_slave_channel_compat(mask, mmp_pdma_filter_fn,
+ &host->dma_drcmrtx,
+ &pdev->dev, "tx");
+ if (host->dma_chan_tx == NULL) {
+ dev_err(&pdev->dev, "unable to request tx dma channel\n");
+ ret = -ENODEV;
goto out;
}
- host->dma_drcmrtx = dmatx->start;
if (host->pdata) {
gpio_cd = host->pdata->gpio_card_detect;
@@ -814,12 +831,12 @@ err_gpio_ro:
gpio_free(gpio_power);
out:
if (host) {
- if (host->dma >= 0)
- pxa_free_dma(host->dma);
+ if (host->dma_chan_rx)
+ dma_release_channel(host->dma_chan_rx);
+ if (host->dma_chan_tx)
+ dma_release_channel(host->dma_chan_tx);
if (host->base)
iounmap(host->base);
- if (host->sg_cpu)
- dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
if (host->clk)
clk_put(host->clk);
}
@@ -863,13 +880,12 @@ static int pxamci_remove(struct platform_device *pdev)
END_CMD_RES|PRG_DONE|DATA_TRAN_DONE,
host->base + MMC_I_MASK);
- DRCMR(host->dma_drcmrrx) = 0;
- DRCMR(host->dma_drcmrtx) = 0;
-
free_irq(host->irq, host);
- pxa_free_dma(host->dma);
+ dmaengine_terminate_all(host->dma_chan_rx);
+ dmaengine_terminate_all(host->dma_chan_tx);
+ dma_release_channel(host->dma_chan_rx);
+ dma_release_channel(host->dma_chan_tx);
iounmap(host->base);
- dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
clk_put(host->clk);
--
1.8.3.1
next prev parent reply other threads:[~2013-08-07 15:33 UTC|newest]
Thread overview: 68+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-07 15:33 [PATCH 00/20] ARM: pxa: move core and drivers to dmaengine Daniel Mack
2013-08-07 15:33 ` [PATCH 01/20] mtd: pxa3xx-nand: replace pxa_request_dma with dmaengine Daniel Mack
2013-08-07 17:46 ` Ezequiel Garcia
2013-08-08 6:42 ` Daniel Mack
2013-08-08 10:12 ` Ezequiel Garcia
2013-08-08 10:14 ` Daniel Mack
2013-08-07 15:33 ` [PATCH 02/20] mtd: pxa3xx-nand: use mmp_pdma_filter_fn and dma_request_slave_channel_compat Daniel Mack
2013-08-07 15:33 ` [PATCH 03/20] ARM: pxa: ssp: add shortcut for &pdev->dev Daniel Mack
2013-08-08 7:32 ` Brian Norris
2013-08-08 7:52 ` Artem Bityutskiy
2013-08-08 8:20 ` Daniel Mack
2013-08-07 15:33 ` [PATCH 04/20] ARM: pxa: ssp: add DT bindings Daniel Mack
2013-08-07 15:54 ` Arnd Bergmann
2013-08-07 15:33 ` [PATCH 05/20] ARM: pxa: ssp: use devm_ functions Daniel Mack
2013-08-07 15:33 ` [PATCH 06/20] tty: serial: pxa: remove old cruft Daniel Mack
2013-08-12 8:19 ` Daniel Mack
2013-08-12 18:08 ` Greg KH
2013-08-07 15:33 ` [PATCH 07/20] spi: spi-pxa2xx: remove legacy PXA DMA bits Daniel Mack
2013-08-07 15:55 ` Mark Brown
2013-08-07 15:59 ` Daniel Mack
2013-08-07 16:41 ` Mark Brown
2013-08-07 15:33 ` Daniel Mack [this message]
2014-10-15 18:32 ` [PATCH 08/20] mmc: host: pxamci: switch over to dmaengine use Vasily Khoruzhick
2014-10-16 17:57 ` Vasily Khoruzhick
2013-08-07 15:33 ` [PATCH 09/20] ata: pdata_pxa: migrate over to dmaengine usage Daniel Mack
2013-08-07 15:59 ` Arnd Bergmann
2013-08-07 15:33 ` [PATCH 10/20] net: irda: pxaficp_ir: switch to dmaengine Daniel Mack
2013-08-07 15:34 ` [PATCH 11/20] net: smc91x.c: switch to generic buf-to-buf DMA offload Daniel Mack
2013-08-07 15:34 ` [PATCH 12/20] net: smc911x.c: switch to dmaengine API Daniel Mack
2013-08-07 15:34 ` [PATCH 13/20] ASoC: pxa: pxa-ssp: add DT bindings Daniel Mack
2013-08-07 16:40 ` Mark Brown
2013-08-08 9:39 ` Daniel Mack
2013-08-08 13:20 ` Mark Brown
2013-08-09 13:03 ` Daniel Mack
2013-08-07 15:34 ` [PATCH 14/20] ASoC: pxa: use snd_dmaengine_dai_dma_data Daniel Mack
2013-08-07 15:57 ` Mark Brown
2013-08-07 15:34 ` [PATCH 15/20] ASoC: pxa: pxa-ssp: set dma filter data from startup hook Daniel Mack
2013-08-07 15:58 ` Mark Brown
2013-08-07 15:34 ` [PATCH 16/20] ASoC: pxa: add DT bindings for pxa2xx-pcm Daniel Mack
2013-08-07 16:06 ` Mark Brown
2013-08-07 15:34 ` [PATCH 17/20] ASoC: pxa: pxa-pcm-lib: switch over to snd-soc-dmaengine-pcm Daniel Mack
2013-08-07 16:07 ` Mark Brown
2013-08-07 16:10 ` Daniel Mack
2013-08-07 16:32 ` Mark Brown
2013-08-08 8:18 ` Daniel Mack
2013-08-08 8:44 ` Lars-Peter Clausen
2013-08-08 9:03 ` Daniel Mack
2013-08-08 9:36 ` Mark Brown
2013-08-08 9:43 ` Daniel Mack
2013-08-08 10:35 ` Mark Brown
2013-08-08 10:39 ` Daniel Mack
2013-08-08 11:03 ` Mark Brown
2013-08-08 10:25 ` Russell King - ARM Linux
2013-08-07 15:34 ` [PATCH 18/20] ARM: pxa: register static mmp_pdma device Daniel Mack
2013-08-07 15:34 ` [PATCH 19/20] ARM: mmp: " Daniel Mack
2013-08-07 15:34 ` [PATCH 20/20] ARM: pxa: remove old DMA implementation Daniel Mack
2013-08-07 16:08 ` [PATCH 00/20] ARM: pxa: move core and drivers to dmaengine Arnd Bergmann
2013-08-09 22:50 ` Robert Jarzmik
2013-08-10 10:56 ` Daniel Mack
2013-08-11 20:05 ` Robert Jarzmik
2013-08-14 10:00 ` Vinod Koul
2013-08-15 15:22 ` Robert Jarzmik
2013-08-15 15:30 ` Daniel Mack
-- strict thread matches above, loose matches on Subject: below --
2013-12-10 9:24 [PATCH 08/20] mmc: host: pxamci: switch over to dmaengine use Sergei Ianovich
[not found] <1375889649-14638-9-git-send-email-zonque>
2013-12-10 9:27 ` Sergei Ianovich
2013-12-10 10:25 ` Sergei Ianovich
2013-12-10 10:48 ` Daniel Mack
2013-12-10 15:04 ` Sergei Ianovich
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1375889649-14638-9-git-send-email-zonque@gmail.com \
--to=zonque@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).