From: jbe@pengutronix.de (Juergen Beisert)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/6] Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver
Date: Wed, 11 Sep 2013 10:18:29 +0200 [thread overview]
Message-ID: <1378887511-24530-5-git-send-email-jbe@pengutronix.de> (raw)
In-Reply-To: <1378887511-24530-1-git-send-email-jbe@pengutronix.de>
Distinguish i.MX23 and i.MX28 at runtime and do the same for both SoC at least
for the 4 wire touchscreen.
Note: support for the remaining LRADC channels is not tested on an
i.MX23 yet.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
CC: linux-arm-kernel at lists.infradead.org
CC: devel at driverdev.osuosl.org
CC: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Jonathan Cameron <jic23@cam.ac.uk>
---
drivers/staging/iio/adc/mxs-lradc.c | 45 +++++++++++++++++++++++++++++++++----
1 file changed, 41 insertions(+), 4 deletions(-)
diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c
index 4317fee..c81b186 100644
--- a/drivers/staging/iio/adc/mxs-lradc.c
+++ b/drivers/staging/iio/adc/mxs-lradc.c
@@ -188,20 +188,33 @@ struct mxs_lradc {
# define LRADC_CTRL0_MX28_XNPSW /* XM */ (1 << 17)
# define LRADC_CTRL0_MX28_XPPSW /* XP */ (1 << 16)
+# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE (1 << 20)
+# define LRADC_CTRL0_MX23_YM (1 << 19)
+# define LRADC_CTRL0_MX23_XM (1 << 18)
+# define LRADC_CTRL0_MX23_YP (1 << 17)
+# define LRADC_CTRL0_MX23_XP (1 << 16)
+
# define LRADC_CTRL0_MX28_PLATE_MASK \
(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
+# define LRADC_CTRL0_MX23_PLATE_MASK \
+ (LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
+ LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
+ LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
+
#define LRADC_CTRL1 0x10
#define LRADC_CTRL1_TOUCH_DETECT_IRQ_EN (1 << 24)
#define LRADC_CTRL1_LRADC_IRQ_EN(n) (1 << ((n) + 16))
#define LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK (0x1fff << 16)
+#define LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK (0x01ff << 16)
#define LRADC_CTRL1_LRADC_IRQ_EN_OFFSET 16
#define LRADC_CTRL1_TOUCH_DETECT_IRQ (1 << 8)
#define LRADC_CTRL1_LRADC_IRQ(n) (1 << (n))
#define LRADC_CTRL1_MX28_LRADC_IRQ_MASK 0x1fff
+#define LRADC_CTRL1_MX23_LRADC_IRQ_MASK 0x01ff
#define LRADC_CTRL1_LRADC_IRQ_OFFSET 0
#define LRADC_CTRL2 0x20
@@ -252,36 +265,50 @@ static void mxs_lradc_reg(struct mxs_lradc *lradc, u32 val, u32 reg)
static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL0_MX23_PLATE_MASK;
return LRADC_CTRL0_MX28_PLATE_MASK;
}
static u32 mxs_lradc_irq_en_mask(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK;
return LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK;
}
static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
}
static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE;
return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
}
static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM;
return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
}
static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM;
return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
}
static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
{
+ if (lradc->soc == IMX23_LRADC)
+ return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
}
@@ -319,7 +346,8 @@ static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
* Virtual channel 0 is always used here as the others are always not
* used if doing raw sampling.
*/
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+ if (lradc->soc == IMX28_LRADC)
+ mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
LRADC_CTRL1);
mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
@@ -767,7 +795,8 @@ static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
if (ret < 0)
goto err_buf;
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+ if (lradc->soc == IMX28_LRADC)
+ mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
LRADC_CTRL1);
mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
@@ -805,7 +834,8 @@ static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
LRADC_DELAY_KICK, LRADC_DELAY(0));
mxs_lradc_reg_clear(lradc, 0xff, LRADC_CTRL0);
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
+ if (lradc->soc == IMX28_LRADC)
+ mxs_lradc_reg_clear(lradc, LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK,
LRADC_CTRL1);
kfree(lradc->buffer);
@@ -909,7 +939,8 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
mxs_lradc_reg(lradc, 0, LRADC_DELAY(3));
/* Configure the touchscreen type */
- mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+ if (lradc->soc == IMX28_LRADC) {
+ mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
LRADC_CTRL0);
if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
@@ -987,6 +1018,12 @@ static int mxs_lradc_probe(struct platform_device *pdev)
dev_warn(dev, "Unsupported number of touchscreen wires (%d)\n",
ts_wires);
+ if ((lradc->soc == IMX23_LRADC) && (ts_wires == 5)) {
+ dev_warn(dev, "No support for 5 wire touches on i.MX23\n");
+ dev_warn(dev, "Falling back to 4 wire\n");
+ ts_wires = 4;
+ }
+
/* Grab all IRQ sources */
for (i = 0; i < of_cfg->irq_count; i++) {
lradc->irq[i] = platform_get_irq(pdev, i);
--
1.8.4.rc3
next prev parent reply other threads:[~2013-09-11 8:18 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-09-11 8:18 [RFCv4] staging/iio/adc: change the MXS touchscreen driver implementation Juergen Beisert
2013-09-11 8:18 ` [PATCH 1/6] Staging/iio/adc/touchscreen/MXS: distinguish i.MX23's and i.MX28's LRADC Juergen Beisert
2013-09-11 8:18 ` [PATCH 2/6] Staging/iio/adc/touchscreen/MXS: separate i.MX28 specific register bits Juergen Beisert
2013-09-15 10:27 ` Jonathan Cameron
2013-09-11 8:18 ` [PATCH 3/6] Staging/iio/adc/touchscreen/MXS: simplify register access Juergen Beisert
2013-09-15 10:35 ` Jonathan Cameron
2013-09-16 8:17 ` Jürgen Beisert
2013-09-16 18:39 ` Jonathan Cameron
2013-09-16 14:15 ` Marek Vasut
2013-09-11 8:18 ` Juergen Beisert [this message]
2013-09-15 10:50 ` [PATCH 4/6] Staging/iio/adc/touchscreen/MXS: add i.MX23 support to the LRADC touchscreen driver Jonathan Cameron
2013-09-16 8:14 ` Jürgen Beisert
2013-09-16 14:19 ` Marek Vasut
2013-09-11 8:18 ` [PATCH 5/6] Staging/iio/adc/touchscreen/MXS: add interrupt driven touch detection Juergen Beisert
2013-09-15 10:56 ` Jonathan Cameron
2013-09-15 16:10 ` Jonathan Cameron
2013-09-16 8:38 ` Jürgen Beisert
2013-09-16 8:10 ` Jürgen Beisert
2013-09-16 9:37 ` Jürgen Beisert
2013-09-16 14:23 ` Marek Vasut
2013-09-16 14:34 ` Jürgen Beisert
2013-09-16 15:10 ` Marek Vasut
2013-09-16 15:30 ` Jonathan Cameron
2013-09-19 12:49 ` Jürgen Beisert
2013-09-19 16:12 ` Jonathan Cameron
2013-09-16 15:28 ` Dmitry Torokhov
2013-09-17 7:33 ` Jürgen Beisert
2013-09-11 8:18 ` [PATCH 6/6] Staging/iio/adc/touchscreen/MXS: Remove old touchscreen detection implementation Juergen Beisert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1378887511-24530-5-git-send-email-jbe@pengutronix.de \
--to=jbe@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).