* [PATCH v4 0/7] ARM: imx27 pinctrl
@ 2013-10-24 7:53 Markus Pargmann
2013-10-24 7:53 ` [PATCH v4 1/7] pinctrl: imx1 core driver Markus Pargmann
` (7 more replies)
0 siblings, 8 replies; 12+ messages in thread
From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
v4 is rebased onto v3.12-rc6, including pinconf_set changes.
this series implements a imx27 pinctrl driver. imx1/21/27 have a register
format that is not compatible with the rest of imx series processors. The
series adds a imx1 core driver for the different register layout.
Regards,
Markus
Markus Pargmann (7):
pinctrl: imx1 core driver
pinctrl: imx27: imx27 pincontrol driver
ARM: dts: imx27 pin functions
ARM: dts: imx27 pinctrl
ARM: dts: imx27 phyCARD-S pinctrl
ARM: dts: imx27 phycore pinctrl
ARM: imx27: enable pinctrl
.../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 ++
arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts | 10 +
arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts | 4 +
arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 2 +
arch/arm/boot/dts/imx27-phytec-phycore-som.dts | 6 +
arch/arm/boot/dts/imx27-pinfunc.h | 524 +++++++++++++++++
arch/arm/boot/dts/imx27.dtsi | 102 ++++
arch/arm/mach-imx/Kconfig | 2 +
drivers/pinctrl/Kconfig | 13 +
drivers/pinctrl/Makefile | 2 +
drivers/pinctrl/pinctrl-imx1-core.c | 653 +++++++++++++++++++++
drivers/pinctrl/pinctrl-imx1.h | 73 +++
drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++
13 files changed, 1918 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt
create mode 100644 arch/arm/boot/dts/imx27-pinfunc.h
create mode 100644 drivers/pinctrl/pinctrl-imx1-core.c
create mode 100644 drivers/pinctrl/pinctrl-imx1.h
create mode 100644 drivers/pinctrl/pinctrl-imx27.c
--
1.8.4.rc3
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v4 1/7] pinctrl: imx1 core driver 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 2/7] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann ` (6 subsequent siblings) 7 siblings, 0 replies; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel Core driver for register formats of imx1/imx21/imx27 processors. The pins of those processors are grouped into ports. Each port has 32 pins. The pins mux configuration is controlled by registers with 1 or 2 bit per pin, depending on the specific control register. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> --- drivers/pinctrl/Kconfig | 5 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-imx1-core.c | 653 ++++++++++++++++++++++++++++++++++++ drivers/pinctrl/pinctrl-imx1.h | 73 ++++ 4 files changed, 732 insertions(+) create mode 100644 drivers/pinctrl/pinctrl-imx1-core.c create mode 100644 drivers/pinctrl/pinctrl-imx1.h diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index b6e864e..8a02aa0 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -80,6 +80,11 @@ config PINCTRL_IMX select PINMUX select PINCONF +config PINCTRL_IMX1_CORE + bool + select PINMUX + select PINCONF + config PINCTRL_IMX35 bool "IMX35 pinctrl driver" depends on OF diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 496d9bf..d7caf08 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o +obj-$(CONFIG_PINCTRL_IMX1_CORE) += pinctrl-imx1-core.o obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o obj-$(CONFIG_PINCTRL_IMX51) += pinctrl-imx51.o obj-$(CONFIG_PINCTRL_IMX53) += pinctrl-imx53.o diff --git a/drivers/pinctrl/pinctrl-imx1-core.c b/drivers/pinctrl/pinctrl-imx1-core.c new file mode 100644 index 0000000..4d5a9e7 --- /dev/null +++ b/drivers/pinctrl/pinctrl-imx1-core.c @@ -0,0 +1,653 @@ +/* + * Core driver for the imx pin controller in imx1/21/27 + * + * Copyright (C) 2013 Pengutronix + * Author: Markus Pargmann <mpa@pengutronix.de> + * + * Based on pinctrl-imx.c: + * Author: Dong Aisheng <dong.aisheng@linaro.org> + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Copyright (C) 2012 Linaro Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/bitops.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/slab.h> + +#include "core.h" +#include "pinctrl-imx1.h" + +struct imx1_pinctrl { + struct device *dev; + struct pinctrl_dev *pctl; + void __iomem *base; + const struct imx1_pinctrl_soc_info *info; +}; + +/* + * MX1 register offsets + */ + +#define MX1_DDIR 0x00 +#define MX1_OCR 0x04 +#define MX1_ICONFA 0x0c +#define MX1_ICONFB 0x10 +#define MX1_GIUS 0x20 +#define MX1_GPR 0x38 +#define MX1_PUEN 0x40 + +#define MX1_PORT_STRIDE 0x100 + + +/* + * MUX_ID format defines + */ +#define MX1_MUX_FUNCTION(val) (BIT(0) & val) +#define MX1_MUX_GPIO(val) ((BIT(1) & val) >> 1) +#define MX1_MUX_DIR(val) ((BIT(2) & val) >> 2) +#define MX1_MUX_OCONF(val) (((BIT(4) | BIT(5)) & val) >> 4) +#define MX1_MUX_ICONFA(val) (((BIT(8) | BIT(9)) & val) >> 8) +#define MX1_MUX_ICONFB(val) (((BIT(10) | BIT(11)) & val) >> 10) + + +/* + * IMX1 IOMUXC manages the pins based on ports. Each port has 32 pins. IOMUX + * control register are seperated into function, output configuration, input + * configuration A, input configuration B, GPIO in use and data direction. + * + * Those controls that are represented by 1 bit have a direct mapping between + * bit position and pin id. If they are represented by 2 bit, the lower 16 pins + * are in the first register and the upper 16 pins in the second (next) + * register. pin_id is stored in bit (pin_id%16)*2 and the bit above. + */ + +/* + * Calculates the register offset from a pin_id + */ +static void __iomem *imx1_mem(struct imx1_pinctrl *ipctl, unsigned int pin_id) +{ + unsigned int port = pin_id / 32; + return ipctl->base + port * MX1_PORT_STRIDE; +} + +/* + * Write to a register with 2 bits per pin. The function will automatically + * use the next register if the pin is managed in the second register. + */ +static void imx1_write_2bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 value, u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = (pin_id % 16) * 2; /* offset, regardless of register used */ + int mask = ~(0x3 << offset); /* Mask for 2 bits@offset */ + u32 old_val; + u32 new_val; + + dev_dbg(ipctl->dev, "write: register 0x%p offset %d value 0x%x\n", + reg, offset, value); + + /* Use the next register if the pin's port pin number is >=16 */ + if (pin_id % 32 >= 16) + reg += 0x04; + + /* Get current state of pins */ + old_val = readl(reg); + old_val &= mask; + + new_val = value & 0x3; /* Make sure value is really 2 bit */ + new_val <<= offset; + new_val |= old_val;/* Set new state for pin_id */ + + writel(new_val, reg); +} + +static void imx1_write_bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 value, u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = pin_id % 32; + int mask = ~BIT_MASK(offset); + u32 old_val; + u32 new_val; + + /* Get current state of pins */ + old_val = readl(reg); + old_val &= mask; + + new_val = value & 0x1; /* Make sure value is really 1 bit */ + new_val <<= offset; + new_val |= old_val;/* Set new state for pin_id */ + + writel(new_val, reg); +} + +static int imx1_read_2bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = pin_id % 16; + + /* Use the next register if the pin's port pin number is >=16 */ + if (pin_id % 32 >= 16) + reg += 0x04; + + return (readl(reg) & (BIT(offset) | BIT(offset+1))) >> offset; +} + +static int imx1_read_bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = pin_id % 32; + + return !!(readl(reg) & BIT(offset)); +} + +static const inline struct imx1_pin_group *imx1_pinctrl_find_group_by_name( + const struct imx1_pinctrl_soc_info *info, + const char *name) +{ + const struct imx1_pin_group *grp = NULL; + int i; + + for (i = 0; i < info->ngroups; i++) { + if (!strcmp(info->groups[i].name, name)) { + grp = &info->groups[i]; + break; + } + } + + return grp; +} + +static int imx1_get_groups_count(struct pinctrl_dev *pctldev) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->ngroups; +} + +static const char *imx1_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->groups[selector].name; +} + +static int imx1_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, + const unsigned int **pins, + unsigned *npins) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + if (selector >= info->ngroups) + return -EINVAL; + + *pins = info->groups[selector].pin_ids; + *npins = info->groups[selector].npins; + + return 0; +} + +static void imx1_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, + unsigned offset) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + + seq_printf(s, "GPIO %d, function %d, direction %d, oconf %d, iconfa %d, iconfb %d", + imx1_read_bit(ipctl, offset, MX1_GIUS), + imx1_read_bit(ipctl, offset, MX1_GPR), + imx1_read_bit(ipctl, offset, MX1_DDIR), + imx1_read_2bit(ipctl, offset, MX1_OCR), + imx1_read_2bit(ipctl, offset, MX1_ICONFA), + imx1_read_2bit(ipctl, offset, MX1_ICONFB)); +} + +static int imx1_dt_node_to_map(struct pinctrl_dev *pctldev, + struct device_node *np, + struct pinctrl_map **map, unsigned *num_maps) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + const struct imx1_pin_group *grp; + struct pinctrl_map *new_map; + struct device_node *parent; + int map_num = 1; + int i, j; + + /* + * first find the group of this node and check if we need create + * config maps for pins + */ + grp = imx1_pinctrl_find_group_by_name(info, np->name); + if (!grp) { + dev_err(info->dev, "unable to find group for node %s\n", + np->name); + return -EINVAL; + } + + for (i = 0; i < grp->npins; i++) + map_num++; + + new_map = kmalloc(sizeof(struct pinctrl_map) * map_num, GFP_KERNEL); + if (!new_map) + return -ENOMEM; + + *map = new_map; + *num_maps = map_num; + + /* create mux map */ + parent = of_get_parent(np); + if (!parent) { + kfree(new_map); + return -EINVAL; + } + new_map[0].type = PIN_MAP_TYPE_MUX_GROUP; + new_map[0].data.mux.function = parent->name; + new_map[0].data.mux.group = np->name; + of_node_put(parent); + + /* create config map */ + new_map++; + for (i = j = 0; i < grp->npins; i++) { + new_map[j].type = PIN_MAP_TYPE_CONFIGS_PIN; + new_map[j].data.configs.group_or_pin = + pin_get_name(pctldev, grp->pins[i].pin_id); + new_map[j].data.configs.configs = &grp->pins[i].config; + new_map[j].data.configs.num_configs = 1; + j++; + } + + dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n", + (*map)->data.mux.function, (*map)->data.mux.group, map_num); + + return 0; +} + +static void imx1_dt_free_map(struct pinctrl_dev *pctldev, + struct pinctrl_map *map, unsigned num_maps) +{ + kfree(map); +} + +static const struct pinctrl_ops imx1_pctrl_ops = { + .get_groups_count = imx1_get_groups_count, + .get_group_name = imx1_get_group_name, + .get_group_pins = imx1_get_group_pins, + .pin_dbg_show = imx1_pin_dbg_show, + .dt_node_to_map = imx1_dt_node_to_map, + .dt_free_map = imx1_dt_free_map, + +}; + +static int imx1_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + const struct imx1_pin *pins; + unsigned int npins; + int i; + + /* + * Configure the mux mode for each pin in the group for a specific + * function. + */ + pins = info->groups[group].pins; + npins = info->groups[group].npins; + + WARN_ON(!pins || !npins); + + dev_dbg(ipctl->dev, "enable function %s group %s\n", + info->functions[selector].name, info->groups[group].name); + + for (i = 0; i < npins; i++) { + unsigned int mux = pins[i].mux_id; + unsigned int pin_id = pins[i].pin_id; + unsigned int afunction = MX1_MUX_FUNCTION(mux); + unsigned int gpio_in_use = MX1_MUX_GPIO(mux); + unsigned int direction = MX1_MUX_DIR(mux); + unsigned int gpio_oconf = MX1_MUX_OCONF(mux); + unsigned int gpio_iconfa = MX1_MUX_ICONFA(mux); + unsigned int gpio_iconfb = MX1_MUX_ICONFB(mux); + + dev_dbg(pctldev->dev, "%s, pin 0x%x, function %d, gpio %d, direction %d, oconf %d, iconfa %d, iconfb %d\n", + __func__, pin_id, afunction, gpio_in_use, + direction, gpio_oconf, gpio_iconfa, + gpio_iconfb); + + imx1_write_bit(ipctl, pin_id, gpio_in_use, MX1_GIUS); + imx1_write_bit(ipctl, pin_id, direction, MX1_DDIR); + + if (gpio_in_use) { + imx1_write_2bit(ipctl, pin_id, gpio_oconf, MX1_OCR); + imx1_write_2bit(ipctl, pin_id, gpio_iconfa, + MX1_ICONFA); + imx1_write_2bit(ipctl, pin_id, gpio_iconfb, + MX1_ICONFB); + } else { + imx1_write_bit(ipctl, pin_id, afunction, MX1_GPR); + } + } + + return 0; +} + +static int imx1_pmx_get_funcs_count(struct pinctrl_dev *pctldev) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->nfunctions; +} + +static const char *imx1_pmx_get_func_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->functions[selector].name; +} + +static int imx1_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector, + const char * const **groups, + unsigned * const num_groups) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + *groups = info->functions[selector].groups; + *num_groups = info->functions[selector].num_groups; + + return 0; +} + +static const struct pinmux_ops imx1_pmx_ops = { + .get_functions_count = imx1_pmx_get_funcs_count, + .get_function_name = imx1_pmx_get_func_name, + .get_function_groups = imx1_pmx_get_groups, + .enable = imx1_pmx_enable, +}; + +static int imx1_pinconf_get(struct pinctrl_dev *pctldev, + unsigned pin_id, unsigned long *config) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + + *config = imx1_read_bit(ipctl, pin_id, MX1_PUEN); + + return 0; +} + +static int imx1_pinconf_set(struct pinctrl_dev *pctldev, + unsigned pin_id, unsigned long *configs, + unsigned num_configs) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + int i; + + for (i = 0; i != num_configs; ++i) { + imx1_write_bit(ipctl, pin_id, configs[i] & 0x01, MX1_PUEN); + + dev_dbg(ipctl->dev, "pinconf set pullup pin %s\n", + info->pins[pin_id].name); + } + + return 0; +} + +static void imx1_pinconf_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned pin_id) +{ + unsigned long config; + + imx1_pinconf_get(pctldev, pin_id, &config); + seq_printf(s, "0x%lx", config); +} + +static void imx1_pinconf_group_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned group) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + struct imx1_pin_group *grp; + unsigned long config; + const char *name; + int i, ret; + + if (group > info->ngroups) + return; + + seq_puts(s, "\n"); + grp = &info->groups[group]; + for (i = 0; i < grp->npins; i++) { + name = pin_get_name(pctldev, grp->pins[i].pin_id); + ret = imx1_pinconf_get(pctldev, grp->pins[i].pin_id, &config); + if (ret) + return; + seq_printf(s, "%s: 0x%lx", name, config); + } +} + +static const struct pinconf_ops imx1_pinconf_ops = { + .pin_config_get = imx1_pinconf_get, + .pin_config_set = imx1_pinconf_set, + .pin_config_dbg_show = imx1_pinconf_dbg_show, + .pin_config_group_dbg_show = imx1_pinconf_group_dbg_show, +}; + +static struct pinctrl_desc imx1_pinctrl_desc = { + .pctlops = &imx1_pctrl_ops, + .pmxops = &imx1_pmx_ops, + .confops = &imx1_pinconf_ops, + .owner = THIS_MODULE, +}; + +static int imx1_pinctrl_parse_groups(struct device_node *np, + struct imx1_pin_group *grp, + struct imx1_pinctrl_soc_info *info, + u32 index) +{ + int size; + const __be32 *list; + int i; + + dev_dbg(info->dev, "group(%d): %s\n", index, np->name); + + /* Initialise group */ + grp->name = np->name; + + /* + * the binding format is fsl,pins = <PIN MUX_ID CONFIG> + */ + list = of_get_property(np, "fsl,pins", &size); + /* we do not check return since it's safe node passed down */ + if (!size || size % 12) { + dev_notice(info->dev, "Not a valid fsl,pins property (%s)\n", + np->name); + return -EINVAL; + } + + grp->npins = size / 12; + grp->pins = devm_kzalloc(info->dev, + grp->npins * sizeof(struct imx1_pin), GFP_KERNEL); + grp->pin_ids = devm_kzalloc(info->dev, + grp->npins * sizeof(unsigned int), GFP_KERNEL); + + if (!grp->pins || !grp->pin_ids) + return -ENOMEM; + + for (i = 0; i < grp->npins; i++) { + grp->pins[i].pin_id = be32_to_cpu(*list++); + grp->pins[i].mux_id = be32_to_cpu(*list++); + grp->pins[i].config = be32_to_cpu(*list++); + + grp->pin_ids[i] = grp->pins[i].pin_id; + } + + return 0; +} + +static int imx1_pinctrl_parse_functions(struct device_node *np, + struct imx1_pinctrl_soc_info *info, + u32 index) +{ + struct device_node *child; + struct imx1_pmx_func *func; + struct imx1_pin_group *grp; + int ret; + static u32 grp_index; + u32 i = 0; + + dev_dbg(info->dev, "parse function(%d): %s\n", index, np->name); + + func = &info->functions[index]; + + /* Initialise function */ + func->name = np->name; + func->num_groups = of_get_child_count(np); + if (func->num_groups <= 0) + return -EINVAL; + + func->groups = devm_kzalloc(info->dev, + func->num_groups * sizeof(char *), GFP_KERNEL); + + if (!func->groups) + return -ENOMEM; + + for_each_child_of_node(np, child) { + func->groups[i] = child->name; + grp = &info->groups[grp_index++]; + ret = imx1_pinctrl_parse_groups(child, grp, info, i++); + if (ret == -ENOMEM) + return ret; + } + + return 0; +} + +static int imx1_pinctrl_parse_dt(struct platform_device *pdev, + struct imx1_pinctrl *pctl, struct imx1_pinctrl_soc_info *info) +{ + struct device_node *np = pdev->dev.of_node; + struct device_node *child; + int ret; + u32 nfuncs = 0; + u32 ngroups = 0; + u32 ifunc = 0; + + if (!np) + return -ENODEV; + + for_each_child_of_node(np, child) { + ++nfuncs; + ngroups += of_get_child_count(child); + } + + if (!nfuncs) { + dev_err(&pdev->dev, "No pin functions defined\n"); + return -EINVAL; + } + + info->nfunctions = nfuncs; + info->functions = devm_kzalloc(&pdev->dev, + nfuncs * sizeof(struct imx1_pmx_func), GFP_KERNEL); + + info->ngroups = ngroups; + info->groups = devm_kzalloc(&pdev->dev, + ngroups * sizeof(struct imx1_pin_group), GFP_KERNEL); + + + if (!info->functions || !info->groups) + return -ENOMEM; + + for_each_child_of_node(np, child) { + ret = imx1_pinctrl_parse_functions(child, info, ifunc++); + if (ret == -ENOMEM) + return -ENOMEM; + } + + return 0; +} + +int imx1_pinctrl_core_probe(struct platform_device *pdev, + struct imx1_pinctrl_soc_info *info) +{ + struct imx1_pinctrl *ipctl; + struct resource *res; + struct pinctrl_desc *pctl_desc; + int ret; + + if (!info || !info->pins || !info->npins) { + dev_err(&pdev->dev, "wrong pinctrl info\n"); + return -EINVAL; + } + info->dev = &pdev->dev; + + /* Create state holders etc for this driver */ + ipctl = devm_kzalloc(&pdev->dev, sizeof(*ipctl), GFP_KERNEL); + if (!ipctl) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -ENOENT; + + ipctl->base = devm_ioremap_nocache(&pdev->dev, res->start, + resource_size(res)); + if (IS_ERR(ipctl->base)) + return PTR_ERR(ipctl->base); + + pctl_desc = &imx1_pinctrl_desc; + pctl_desc->name = dev_name(&pdev->dev); + pctl_desc->pins = info->pins; + pctl_desc->npins = info->npins; + + ret = imx1_pinctrl_parse_dt(pdev, ipctl, info); + if (ret) { + dev_err(&pdev->dev, "fail to probe dt properties\n"); + return ret; + } + + ipctl->info = info; + ipctl->dev = info->dev; + platform_set_drvdata(pdev, ipctl); + ipctl->pctl = pinctrl_register(pctl_desc, &pdev->dev, ipctl); + if (!ipctl->pctl) { + dev_err(&pdev->dev, "could not register IMX pinctrl driver\n"); + return -EINVAL; + } + + dev_info(&pdev->dev, "initialized IMX pinctrl driver\n"); + + return 0; +} + +int imx1_pinctrl_core_remove(struct platform_device *pdev) +{ + struct imx1_pinctrl *ipctl = platform_get_drvdata(pdev); + + pinctrl_unregister(ipctl->pctl); + + return 0; +} diff --git a/drivers/pinctrl/pinctrl-imx1.h b/drivers/pinctrl/pinctrl-imx1.h new file mode 100644 index 0000000..692a54c --- /dev/null +++ b/drivers/pinctrl/pinctrl-imx1.h @@ -0,0 +1,73 @@ +/* + * IMX pinmux core definitions + * + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Copyright (C) 2012 Linaro Ltd. + * + * Author: Dong Aisheng <dong.aisheng@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __DRIVERS_PINCTRL_IMX1_H +#define __DRIVERS_PINCTRL_IMX1_H + +struct platform_device; + +/** + * struct imx1_pin - describes an IMX1/21/27 pin. + * @pin_id: ID of the described pin. + * @mux_id: ID of the mux setup. + * @config: Configuration of the pin (currently only pullup-enable). + */ +struct imx1_pin { + unsigned int pin_id; + unsigned int mux_id; + unsigned long config; +}; + +/** + * struct imx1_pin_group - describes an IMX pin group + * @name: the name of this specific pin group + * @pins: an array of imx1_pin structs used in this group + * @npins: the number of pins in this group array, i.e. the number of + * elements in .pins so we can iterate over that array + */ +struct imx1_pin_group { + const char *name; + unsigned int *pin_ids; + struct imx1_pin *pins; + unsigned npins; +}; + +/** + * struct imx1_pmx_func - describes IMX pinmux functions + * @name: the name of this specific function + * @groups: corresponding pin groups + * @num_groups: the number of groups + */ +struct imx1_pmx_func { + const char *name; + const char **groups; + unsigned num_groups; +}; + +struct imx1_pinctrl_soc_info { + struct device *dev; + const struct pinctrl_pin_desc *pins; + unsigned int npins; + struct imx1_pin_group *groups; + unsigned int ngroups; + struct imx1_pmx_func *functions; + unsigned int nfunctions; +}; + +#define IMX_PINCTRL_PIN(pin) PINCTRL_PIN(pin, #pin) + +int imx1_pinctrl_core_probe(struct platform_device *pdev, + struct imx1_pinctrl_soc_info *info); +int imx1_pinctrl_core_remove(struct platform_device *pdev); +#endif /* __DRIVERS_PINCTRL_IMX1_H */ -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 2/7] pinctrl: imx27: imx27 pincontrol driver 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 1/7] pinctrl: imx1 core driver Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 10:19 ` Grant Likely 2013-10-24 7:53 ` [PATCH v4 3/7] ARM: dts: imx27 pin functions Markus Pargmann ` (5 subsequent siblings) 7 siblings, 1 reply; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel imx27 pincontrol driver using the imx1 core driver. The DT bindings are similar to other imx pincontrol drivers. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> --- .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 +++ drivers/pinctrl/Kconfig | 8 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++++++++ 4 files changed, 536 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt create mode 100644 drivers/pinctrl/pinctrl-imx27.c diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt new file mode 100644 index 0000000..6619968 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt @@ -0,0 +1,50 @@ +* Freescale IMX27 IOMUX Controller + +Required properties: +- compatible: "fsl,imx27-iomuxc" + +The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. + +Required properties for pin configuration node: +- fsl,pins: three integers array, represents a group of pins mux and config + setting. The format is fsl,pins = <PIN MUX_ID CONFIG>. PIN and MUX_ID are + defined as macros in arch/arm/boot/dts/imx27-pinfunc.h. CONFIG can be 0 or + 1, meaning Pullup disable/enable. + PIN is a integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable + configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin + number on the specific port (between 0 and 31). + MUX_ID is + function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) + function: 0 - Primary function + 1 - Alternate function + 2 - GPIO + direction: 0 - Input + 1 - Output + gpio_oconf: 0 - A_IN + 1 - B_IN + 2 - C_IN + 3 - Data Register + gpio_iconfa/b: 0 - GPIO_IN + 1 - Interrupt Status Register + 2 - 0 + 3 - 1 + +Example: + +iomuxc: iomuxc@10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + + uart { + pinctrl_uart1: uart-1 { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + ... + }; +}; diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 8a02aa0..4c3e5d2 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -85,6 +85,14 @@ config PINCTRL_IMX1_CORE select PINMUX select PINCONF +config PINCTRL_IMX27 + bool "IMX27 pinctrl driver" + depends on OF + depends on SOC_IMX27 + select PINCTRL_IMX1_CORE + help + Say Y here to enable the imx27 pinctrl driver + config PINCTRL_IMX35 bool "IMX35 pinctrl driver" depends on OF diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index d7caf08..5d23b71 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -19,6 +19,7 @@ obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o obj-$(CONFIG_PINCTRL_IMX1_CORE) += pinctrl-imx1-core.o +obj-$(CONFIG_PINCTRL_IMX27) += pinctrl-imx27.o obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o obj-$(CONFIG_PINCTRL_IMX51) += pinctrl-imx51.o obj-$(CONFIG_PINCTRL_IMX53) += pinctrl-imx53.o diff --git a/drivers/pinctrl/pinctrl-imx27.c b/drivers/pinctrl/pinctrl-imx27.c new file mode 100644 index 0000000..417c992 --- /dev/null +++ b/drivers/pinctrl/pinctrl-imx27.c @@ -0,0 +1,477 @@ +/* + * imx27 pinctrl driver based on imx pinmux core + * + * Copyright (C) 2013 Pengutronix + * + * Author: Markus Pargmann <mpa@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pinctrl/pinctrl.h> + +#include "pinctrl-imx1.h" + +#define PAD_ID(port, pin) (port*32 + pin) +#define PA 0 +#define PB 1 +#define PC 2 +#define PD 3 +#define PE 4 +#define PF 5 + +enum imx27_pads { + MX27_PAD_USBH2_CLK = PAD_ID(PA, 0), + MX27_PAD_USBH2_DIR = PAD_ID(PA, 1), + MX27_PAD_USBH2_DATA7 = PAD_ID(PA, 2), + MX27_PAD_USBH2_NXT = PAD_ID(PA, 3), + MX27_PAD_USBH2_STP = PAD_ID(PA, 4), + MX27_PAD_LSCLK = PAD_ID(PA, 5), + MX27_PAD_LD0 = PAD_ID(PA, 6), + MX27_PAD_LD1 = PAD_ID(PA, 7), + MX27_PAD_LD2 = PAD_ID(PA, 8), + MX27_PAD_LD3 = PAD_ID(PA, 9), + MX27_PAD_LD4 = PAD_ID(PA, 10), + MX27_PAD_LD5 = PAD_ID(PA, 11), + MX27_PAD_LD6 = PAD_ID(PA, 12), + MX27_PAD_LD7 = PAD_ID(PA, 13), + MX27_PAD_LD8 = PAD_ID(PA, 14), + MX27_PAD_LD9 = PAD_ID(PA, 15), + MX27_PAD_LD10 = PAD_ID(PA, 16), + MX27_PAD_LD11 = PAD_ID(PA, 17), + MX27_PAD_LD12 = PAD_ID(PA, 18), + MX27_PAD_LD13 = PAD_ID(PA, 19), + MX27_PAD_LD14 = PAD_ID(PA, 20), + MX27_PAD_LD15 = PAD_ID(PA, 21), + MX27_PAD_LD16 = PAD_ID(PA, 22), + MX27_PAD_LD17 = PAD_ID(PA, 23), + MX27_PAD_REV = PAD_ID(PA, 24), + MX27_PAD_CLS = PAD_ID(PA, 25), + MX27_PAD_PS = PAD_ID(PA, 26), + MX27_PAD_SPL_SPR = PAD_ID(PA, 27), + MX27_PAD_HSYNC = PAD_ID(PA, 28), + MX27_PAD_VSYNC = PAD_ID(PA, 29), + MX27_PAD_CONTRAST = PAD_ID(PA, 30), + MX27_PAD_OE_ACD = PAD_ID(PA, 31), + + MX27_PAD_UNUSED0 = PAD_ID(PB, 0), + MX27_PAD_UNUSED1 = PAD_ID(PB, 1), + MX27_PAD_UNUSED2 = PAD_ID(PB, 2), + MX27_PAD_UNUSED3 = PAD_ID(PB, 3), + MX27_PAD_SD2_D0 = PAD_ID(PB, 4), + MX27_PAD_SD2_D1 = PAD_ID(PB, 5), + MX27_PAD_SD2_D2 = PAD_ID(PB, 6), + MX27_PAD_SD2_D3 = PAD_ID(PB, 7), + MX27_PAD_SD2_CMD = PAD_ID(PB, 8), + MX27_PAD_SD2_CLK = PAD_ID(PB, 9), + MX27_PAD_CSI_D0 = PAD_ID(PB, 10), + MX27_PAD_CSI_D1 = PAD_ID(PB, 11), + MX27_PAD_CSI_D2 = PAD_ID(PB, 12), + MX27_PAD_CSI_D3 = PAD_ID(PB, 13), + MX27_PAD_CSI_D4 = PAD_ID(PB, 14), + MX27_PAD_CSI_MCLK = PAD_ID(PB, 15), + MX27_PAD_CSI_PIXCLK = PAD_ID(PB, 16), + MX27_PAD_CSI_D5 = PAD_ID(PB, 17), + MX27_PAD_CSI_D6 = PAD_ID(PB, 18), + MX27_PAD_CSI_D7 = PAD_ID(PB, 19), + MX27_PAD_CSI_VSYNC = PAD_ID(PB, 20), + MX27_PAD_CSI_HSYNC = PAD_ID(PB, 21), + MX27_PAD_USBH1_SUSP = PAD_ID(PB, 22), + MX27_PAD_USB_PWR = PAD_ID(PB, 23), + MX27_PAD_USB_OC_B = PAD_ID(PB, 24), + MX27_PAD_USBH1_RCV = PAD_ID(PB, 25), + MX27_PAD_USBH1_FS = PAD_ID(PB, 26), + MX27_PAD_USBH1_OE_B = PAD_ID(PB, 27), + MX27_PAD_USBH1_TXDM = PAD_ID(PB, 28), + MX27_PAD_USBH1_TXDP = PAD_ID(PB, 29), + MX27_PAD_USBH1_RXDM = PAD_ID(PB, 30), + MX27_PAD_USBH1_RXDP = PAD_ID(PB, 31), + + MX27_PAD_UNUSED4 = PAD_ID(PC, 0), + MX27_PAD_UNUSED5 = PAD_ID(PC, 1), + MX27_PAD_UNUSED6 = PAD_ID(PC, 2), + MX27_PAD_UNUSED7 = PAD_ID(PC, 3), + MX27_PAD_UNUSED8 = PAD_ID(PC, 4), + MX27_PAD_I2C2_SDA = PAD_ID(PC, 5), + MX27_PAD_I2C2_SCL = PAD_ID(PC, 6), + MX27_PAD_USBOTG_DATA5 = PAD_ID(PC, 7), + MX27_PAD_USBOTG_DATA6 = PAD_ID(PC, 8), + MX27_PAD_USBOTG_DATA0 = PAD_ID(PC, 9), + MX27_PAD_USBOTG_DATA2 = PAD_ID(PC, 10), + MX27_PAD_USBOTG_DATA1 = PAD_ID(PC, 11), + MX27_PAD_USBOTG_DATA4 = PAD_ID(PC, 12), + MX27_PAD_USBOTG_DATA3 = PAD_ID(PC, 13), + MX27_PAD_TOUT = PAD_ID(PC, 14), + MX27_PAD_TIN = PAD_ID(PC, 15), + MX27_PAD_SSI4_FS = PAD_ID(PC, 16), + MX27_PAD_SSI4_RXDAT = PAD_ID(PC, 17), + MX27_PAD_SSI4_TXDAT = PAD_ID(PC, 18), + MX27_PAD_SSI4_CLK = PAD_ID(PC, 19), + MX27_PAD_SSI1_FS = PAD_ID(PC, 20), + MX27_PAD_SSI1_RXDAT = PAD_ID(PC, 21), + MX27_PAD_SSI1_TXDAT = PAD_ID(PC, 22), + MX27_PAD_SSI1_CLK = PAD_ID(PC, 23), + MX27_PAD_SSI2_FS = PAD_ID(PC, 24), + MX27_PAD_SSI2_RXDAT = PAD_ID(PC, 25), + MX27_PAD_SSI2_TXDAT = PAD_ID(PC, 26), + MX27_PAD_SSI2_CLK = PAD_ID(PC, 27), + MX27_PAD_SSI3_FS = PAD_ID(PC, 28), + MX27_PAD_SSI3_RXDAT = PAD_ID(PC, 29), + MX27_PAD_SSI3_TXDAT = PAD_ID(PC, 30), + MX27_PAD_SSI3_CLK = PAD_ID(PC, 31), + + MX27_PAD_SD3_CMD = PAD_ID(PD, 0), + MX27_PAD_SD3_CLK = PAD_ID(PD, 1), + MX27_PAD_ATA_DATA0 = PAD_ID(PD, 2), + MX27_PAD_ATA_DATA1 = PAD_ID(PD, 3), + MX27_PAD_ATA_DATA2 = PAD_ID(PD, 4), + MX27_PAD_ATA_DATA3 = PAD_ID(PD, 5), + MX27_PAD_ATA_DATA4 = PAD_ID(PD, 6), + MX27_PAD_ATA_DATA5 = PAD_ID(PD, 7), + MX27_PAD_ATA_DATA6 = PAD_ID(PD, 8), + MX27_PAD_ATA_DATA7 = PAD_ID(PD, 9), + MX27_PAD_ATA_DATA8 = PAD_ID(PD, 10), + MX27_PAD_ATA_DATA9 = PAD_ID(PD, 11), + MX27_PAD_ATA_DATA10 = PAD_ID(PD, 12), + MX27_PAD_ATA_DATA11 = PAD_ID(PD, 13), + MX27_PAD_ATA_DATA12 = PAD_ID(PD, 14), + MX27_PAD_ATA_DATA13 = PAD_ID(PD, 15), + MX27_PAD_ATA_DATA14 = PAD_ID(PD, 16), + MX27_PAD_I2C_DATA = PAD_ID(PD, 17), + MX27_PAD_I2C_CLK = PAD_ID(PD, 18), + MX27_PAD_CSPI2_SS2 = PAD_ID(PD, 19), + MX27_PAD_CSPI2_SS1 = PAD_ID(PD, 20), + MX27_PAD_CSPI2_SS0 = PAD_ID(PD, 21), + MX27_PAD_CSPI2_SCLK = PAD_ID(PD, 22), + MX27_PAD_CSPI2_MISO = PAD_ID(PD, 23), + MX27_PAD_CSPI2_MOSI = PAD_ID(PD, 24), + MX27_PAD_CSPI1_RDY = PAD_ID(PD, 25), + MX27_PAD_CSPI1_SS2 = PAD_ID(PD, 26), + MX27_PAD_CSPI1_SS1 = PAD_ID(PD, 27), + MX27_PAD_CSPI1_SS0 = PAD_ID(PD, 28), + MX27_PAD_CSPI1_SCLK = PAD_ID(PD, 29), + MX27_PAD_CSPI1_MISO = PAD_ID(PD, 30), + MX27_PAD_CSPI1_MOSI = PAD_ID(PD, 31), + + MX27_PAD_USBOTG_NXT = PAD_ID(PE, 0), + MX27_PAD_USBOTG_STP = PAD_ID(PE, 1), + MX27_PAD_USBOTG_DIR = PAD_ID(PE, 2), + MX27_PAD_UART2_CTS = PAD_ID(PE, 3), + MX27_PAD_UART2_RTS = PAD_ID(PE, 4), + MX27_PAD_PWMO = PAD_ID(PE, 5), + MX27_PAD_UART2_TXD = PAD_ID(PE, 6), + MX27_PAD_UART2_RXD = PAD_ID(PE, 7), + MX27_PAD_UART3_TXD = PAD_ID(PE, 8), + MX27_PAD_UART3_RXD = PAD_ID(PE, 9), + MX27_PAD_UART3_CTS = PAD_ID(PE, 10), + MX27_PAD_UART3_RTS = PAD_ID(PE, 11), + MX27_PAD_UART1_TXD = PAD_ID(PE, 12), + MX27_PAD_UART1_RXD = PAD_ID(PE, 13), + MX27_PAD_UART1_CTS = PAD_ID(PE, 14), + MX27_PAD_UART1_RTS = PAD_ID(PE, 15), + MX27_PAD_RTCK = PAD_ID(PE, 16), + MX27_PAD_RESET_OUT_B = PAD_ID(PE, 17), + MX27_PAD_SD1_D0 = PAD_ID(PE, 18), + MX27_PAD_SD1_D1 = PAD_ID(PE, 19), + MX27_PAD_SD1_D2 = PAD_ID(PE, 20), + MX27_PAD_SD1_D3 = PAD_ID(PE, 21), + MX27_PAD_SD1_CMD = PAD_ID(PE, 22), + MX27_PAD_SD1_CLK = PAD_ID(PE, 23), + MX27_PAD_USBOTG_CLK = PAD_ID(PE, 24), + MX27_PAD_USBOTG_DATA7 = PAD_ID(PE, 25), + MX27_PAD_UNUSED9 = PAD_ID(PE, 26), + MX27_PAD_UNUSED10 = PAD_ID(PE, 27), + MX27_PAD_UNUSED11 = PAD_ID(PE, 28), + MX27_PAD_UNUSED12 = PAD_ID(PE, 29), + MX27_PAD_UNUSED13 = PAD_ID(PE, 30), + MX27_PAD_UNUSED14 = PAD_ID(PE, 31), + + MX27_PAD_NFRB = PAD_ID(PF, 0), + MX27_PAD_NFCLE = PAD_ID(PF, 1), + MX27_PAD_NFWP_B = PAD_ID(PF, 2), + MX27_PAD_NFCE_B = PAD_ID(PF, 3), + MX27_PAD_NFALE = PAD_ID(PF, 4), + MX27_PAD_NFRE_B = PAD_ID(PF, 5), + MX27_PAD_NFWE_B = PAD_ID(PF, 6), + MX27_PAD_PC_POE = PAD_ID(PF, 7), + MX27_PAD_PC_RW_B = PAD_ID(PF, 8), + MX27_PAD_IOIS16 = PAD_ID(PF, 9), + MX27_PAD_PC_RST = PAD_ID(PF, 10), + MX27_PAD_PC_BVD2 = PAD_ID(PF, 11), + MX27_PAD_PC_BVD1 = PAD_ID(PF, 12), + MX27_PAD_PC_VS2 = PAD_ID(PF, 13), + MX27_PAD_PC_VS1 = PAD_ID(PF, 14), + MX27_PAD_CLKO = PAD_ID(PF, 15), + MX27_PAD_PC_PWRON = PAD_ID(PF, 16), + MX27_PAD_PC_READY = PAD_ID(PF, 17), + MX27_PAD_PC_WAIT_B = PAD_ID(PF, 18), + MX27_PAD_PC_CD2_B = PAD_ID(PF, 19), + MX27_PAD_PC_CD1_B = PAD_ID(PF, 20), + MX27_PAD_CS4_B = PAD_ID(PF, 21), + MX27_PAD_CS5_B = PAD_ID(PF, 22), + MX27_PAD_ATA_DATA15 = PAD_ID(PF, 23), + MX27_PAD_UNUSED15 = PAD_ID(PF, 24), + MX27_PAD_UNUSED16 = PAD_ID(PF, 25), + MX27_PAD_UNUSED17 = PAD_ID(PF, 26), + MX27_PAD_UNUSED18 = PAD_ID(PF, 27), + MX27_PAD_UNUSED19 = PAD_ID(PF, 28), + MX27_PAD_UNUSED20 = PAD_ID(PF, 29), + MX27_PAD_UNUSED21 = PAD_ID(PF, 30), + MX27_PAD_UNUSED22 = PAD_ID(PF, 31), +}; + +/* Pad names for the pinmux subsystem */ +static const struct pinctrl_pin_desc imx27_pinctrl_pads[] = { + IMX_PINCTRL_PIN(MX27_PAD_USBH2_CLK), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_DIR), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_DATA7), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_NXT), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_STP), + IMX_PINCTRL_PIN(MX27_PAD_LSCLK), + IMX_PINCTRL_PIN(MX27_PAD_LD0), + IMX_PINCTRL_PIN(MX27_PAD_LD1), + IMX_PINCTRL_PIN(MX27_PAD_LD2), + IMX_PINCTRL_PIN(MX27_PAD_LD3), + IMX_PINCTRL_PIN(MX27_PAD_LD4), + IMX_PINCTRL_PIN(MX27_PAD_LD5), + IMX_PINCTRL_PIN(MX27_PAD_LD6), + IMX_PINCTRL_PIN(MX27_PAD_LD7), + IMX_PINCTRL_PIN(MX27_PAD_LD8), + IMX_PINCTRL_PIN(MX27_PAD_LD9), + IMX_PINCTRL_PIN(MX27_PAD_LD10), + IMX_PINCTRL_PIN(MX27_PAD_LD11), + IMX_PINCTRL_PIN(MX27_PAD_LD12), + IMX_PINCTRL_PIN(MX27_PAD_LD13), + IMX_PINCTRL_PIN(MX27_PAD_LD14), + IMX_PINCTRL_PIN(MX27_PAD_LD15), + IMX_PINCTRL_PIN(MX27_PAD_LD16), + IMX_PINCTRL_PIN(MX27_PAD_LD17), + IMX_PINCTRL_PIN(MX27_PAD_REV), + IMX_PINCTRL_PIN(MX27_PAD_CLS), + IMX_PINCTRL_PIN(MX27_PAD_PS), + IMX_PINCTRL_PIN(MX27_PAD_SPL_SPR), + IMX_PINCTRL_PIN(MX27_PAD_HSYNC), + IMX_PINCTRL_PIN(MX27_PAD_VSYNC), + IMX_PINCTRL_PIN(MX27_PAD_CONTRAST), + IMX_PINCTRL_PIN(MX27_PAD_OE_ACD), + + IMX_PINCTRL_PIN(MX27_PAD_UNUSED0), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED1), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED2), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED3), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D0), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D1), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D2), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D3), + IMX_PINCTRL_PIN(MX27_PAD_SD2_CMD), + IMX_PINCTRL_PIN(MX27_PAD_SD2_CLK), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D0), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D1), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D2), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D3), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D4), + IMX_PINCTRL_PIN(MX27_PAD_CSI_MCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSI_PIXCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D5), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D6), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D7), + IMX_PINCTRL_PIN(MX27_PAD_CSI_VSYNC), + IMX_PINCTRL_PIN(MX27_PAD_CSI_HSYNC), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_SUSP), + IMX_PINCTRL_PIN(MX27_PAD_USB_PWR), + IMX_PINCTRL_PIN(MX27_PAD_USB_OC_B), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RCV), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_FS), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_OE_B), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_TXDM), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_TXDP), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RXDM), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RXDP), + + IMX_PINCTRL_PIN(MX27_PAD_UNUSED4), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED5), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED6), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED7), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED8), + IMX_PINCTRL_PIN(MX27_PAD_I2C2_SDA), + IMX_PINCTRL_PIN(MX27_PAD_I2C2_SCL), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA5), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA6), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA0), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA2), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA1), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA4), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA3), + IMX_PINCTRL_PIN(MX27_PAD_TOUT), + IMX_PINCTRL_PIN(MX27_PAD_TIN), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_CLK), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_CLK), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_CLK), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_CLK), + + IMX_PINCTRL_PIN(MX27_PAD_SD3_CMD), + IMX_PINCTRL_PIN(MX27_PAD_SD3_CLK), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA0), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA1), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA2), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA3), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA4), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA5), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA6), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA7), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA8), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA9), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA10), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA11), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA12), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA13), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA14), + IMX_PINCTRL_PIN(MX27_PAD_I2C_DATA), + IMX_PINCTRL_PIN(MX27_PAD_I2C_CLK), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS2), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS1), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS0), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_MISO), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_MOSI), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_RDY), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS2), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS1), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS0), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_MISO), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_MOSI), + + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_NXT), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_STP), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DIR), + IMX_PINCTRL_PIN(MX27_PAD_UART2_CTS), + IMX_PINCTRL_PIN(MX27_PAD_UART2_RTS), + IMX_PINCTRL_PIN(MX27_PAD_PWMO), + IMX_PINCTRL_PIN(MX27_PAD_UART2_TXD), + IMX_PINCTRL_PIN(MX27_PAD_UART2_RXD), + IMX_PINCTRL_PIN(MX27_PAD_UART3_TXD), + IMX_PINCTRL_PIN(MX27_PAD_UART3_RXD), + IMX_PINCTRL_PIN(MX27_PAD_UART3_CTS), + IMX_PINCTRL_PIN(MX27_PAD_UART3_RTS), + IMX_PINCTRL_PIN(MX27_PAD_UART1_TXD), + IMX_PINCTRL_PIN(MX27_PAD_UART1_RXD), + IMX_PINCTRL_PIN(MX27_PAD_UART1_CTS), + IMX_PINCTRL_PIN(MX27_PAD_UART1_RTS), + IMX_PINCTRL_PIN(MX27_PAD_RTCK), + IMX_PINCTRL_PIN(MX27_PAD_RESET_OUT_B), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D0), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D1), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D2), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D3), + IMX_PINCTRL_PIN(MX27_PAD_SD1_CMD), + IMX_PINCTRL_PIN(MX27_PAD_SD1_CLK), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_CLK), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA7), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED9), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED10), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED11), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED12), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED13), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED14), + + IMX_PINCTRL_PIN(MX27_PAD_NFRB), + IMX_PINCTRL_PIN(MX27_PAD_NFCLE), + IMX_PINCTRL_PIN(MX27_PAD_NFWP_B), + IMX_PINCTRL_PIN(MX27_PAD_NFCE_B), + IMX_PINCTRL_PIN(MX27_PAD_NFALE), + IMX_PINCTRL_PIN(MX27_PAD_NFRE_B), + IMX_PINCTRL_PIN(MX27_PAD_NFWE_B), + IMX_PINCTRL_PIN(MX27_PAD_PC_POE), + IMX_PINCTRL_PIN(MX27_PAD_PC_RW_B), + IMX_PINCTRL_PIN(MX27_PAD_IOIS16), + IMX_PINCTRL_PIN(MX27_PAD_PC_RST), + IMX_PINCTRL_PIN(MX27_PAD_PC_BVD2), + IMX_PINCTRL_PIN(MX27_PAD_PC_BVD1), + IMX_PINCTRL_PIN(MX27_PAD_PC_VS2), + IMX_PINCTRL_PIN(MX27_PAD_PC_VS1), + IMX_PINCTRL_PIN(MX27_PAD_CLKO), + IMX_PINCTRL_PIN(MX27_PAD_PC_PWRON), + IMX_PINCTRL_PIN(MX27_PAD_PC_READY), + IMX_PINCTRL_PIN(MX27_PAD_PC_WAIT_B), + IMX_PINCTRL_PIN(MX27_PAD_PC_CD2_B), + IMX_PINCTRL_PIN(MX27_PAD_PC_CD1_B), + IMX_PINCTRL_PIN(MX27_PAD_CS4_B), + IMX_PINCTRL_PIN(MX27_PAD_CS5_B), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA15), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED15), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED16), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED17), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED18), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED19), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED20), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED21), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED22), +}; + +static struct imx1_pinctrl_soc_info imx27_pinctrl_info = { + .pins = imx27_pinctrl_pads, + .npins = ARRAY_SIZE(imx27_pinctrl_pads), +}; + +static struct of_device_id imx27_pinctrl_of_match[] = { + { .compatible = "fsl,imx27-iomuxc", }, + { /* sentinel */ } +}; + +struct imx27_pinctrl_private { + int num_gpio_childs; + struct platform_device **gpio_dev; + struct mxc_gpio_platform_data *gpio_pdata; +}; + +static int imx27_pinctrl_probe(struct platform_device *pdev) +{ + return imx1_pinctrl_core_probe(pdev, &imx27_pinctrl_info); +} + +static struct platform_driver imx27_pinctrl_driver = { + .driver = { + .name = "imx27-pinctrl", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(imx27_pinctrl_of_match), + }, + .probe = imx27_pinctrl_probe, + .remove = imx1_pinctrl_core_remove, +}; + +static int __init imx27_pinctrl_init(void) +{ + return platform_driver_register(&imx27_pinctrl_driver); +} +arch_initcall(imx27_pinctrl_init); + +static void __exit imx27_pinctrl_exit(void) +{ + platform_driver_unregister(&imx27_pinctrl_driver); +} +module_exit(imx27_pinctrl_exit); +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>"); +MODULE_DESCRIPTION("Freescale IMX27 pinctrl driver"); +MODULE_LICENSE("GPL v2"); -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 2/7] pinctrl: imx27: imx27 pincontrol driver 2013-10-24 7:53 ` [PATCH v4 2/7] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann @ 2013-10-24 10:19 ` Grant Likely 0 siblings, 0 replies; 12+ messages in thread From: Grant Likely @ 2013-10-24 10:19 UTC (permalink / raw) To: linux-arm-kernel On Thu, 24 Oct 2013 09:53:48 +0200, Markus Pargmann <mpa@pengutronix.de> wrote: > imx27 pincontrol driver using the imx1 core driver. The DT bindings are > similar to other imx pincontrol drivers. > > Signed-off-by: Markus Pargmann <mpa@pengutronix.de> > Acked-by: Sascha Hauer <s.hauer@pengutronix.de> > Acked-by: Shawn Guo <shawn.guo@linaro.org> Binding looks okay to me. g. > --- > .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 +++ > drivers/pinctrl/Kconfig | 8 + > drivers/pinctrl/Makefile | 1 + > drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++++++++ > 4 files changed, 536 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > create mode 100644 drivers/pinctrl/pinctrl-imx27.c > > diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > new file mode 100644 > index 0000000..6619968 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > @@ -0,0 +1,50 @@ > +* Freescale IMX27 IOMUX Controller > + > +Required properties: > +- compatible: "fsl,imx27-iomuxc" > + > +The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. > + > +Required properties for pin configuration node: > +- fsl,pins: three integers array, represents a group of pins mux and config > + setting. The format is fsl,pins = <PIN MUX_ID CONFIG>. PIN and MUX_ID are > + defined as macros in arch/arm/boot/dts/imx27-pinfunc.h. CONFIG can be 0 or > + 1, meaning Pullup disable/enable. > + PIN is a integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable > + configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin > + number on the specific port (between 0 and 31). > + MUX_ID is > + function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) > + function: 0 - Primary function > + 1 - Alternate function > + 2 - GPIO > + direction: 0 - Input > + 1 - Output > + gpio_oconf: 0 - A_IN > + 1 - B_IN > + 2 - C_IN > + 3 - Data Register > + gpio_iconfa/b: 0 - GPIO_IN > + 1 - Interrupt Status Register > + 2 - 0 > + 3 - 1 > + > +Example: > + > +iomuxc: iomuxc at 10015000 { > + compatible = "fsl,imx27-iomuxc"; > + reg = <0x10015000 0x600>; > + > + uart { > + pinctrl_uart1: uart-1 { > + fsl,pins = < > + MX27_PAD_UART1_TXD__UART1_TXD 0x0 > + MX27_PAD_UART1_RXD__UART1_RXD 0x0 > + MX27_PAD_UART1_CTS__UART1_CTS 0x0 > + MX27_PAD_UART1_RTS__UART1_RTS 0x0 > + >; > + }; > + > + ... > + }; > +}; > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > index 8a02aa0..4c3e5d2 100644 > --- a/drivers/pinctrl/Kconfig > +++ b/drivers/pinctrl/Kconfig > @@ -85,6 +85,14 @@ config PINCTRL_IMX1_CORE > select PINMUX > select PINCONF > > +config PINCTRL_IMX27 > + bool "IMX27 pinctrl driver" > + depends on OF > + depends on SOC_IMX27 > + select PINCTRL_IMX1_CORE > + help > + Say Y here to enable the imx27 pinctrl driver > + > config PINCTRL_IMX35 > bool "IMX35 pinctrl driver" > depends on OF > diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile > index d7caf08..5d23b71 100644 > --- a/drivers/pinctrl/Makefile > +++ b/drivers/pinctrl/Makefile > @@ -19,6 +19,7 @@ obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o > obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o > obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o > obj-$(CONFIG_PINCTRL_IMX1_CORE) += pinctrl-imx1-core.o > +obj-$(CONFIG_PINCTRL_IMX27) += pinctrl-imx27.o > obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o > obj-$(CONFIG_PINCTRL_IMX51) += pinctrl-imx51.o > obj-$(CONFIG_PINCTRL_IMX53) += pinctrl-imx53.o > diff --git a/drivers/pinctrl/pinctrl-imx27.c b/drivers/pinctrl/pinctrl-imx27.c > new file mode 100644 > index 0000000..417c992 > --- /dev/null > +++ b/drivers/pinctrl/pinctrl-imx27.c > @@ -0,0 +1,477 @@ > +/* > + * imx27 pinctrl driver based on imx pinmux core > + * > + * Copyright (C) 2013 Pengutronix > + * > + * Author: Markus Pargmann <mpa@pengutronix.de> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + */ > + > +#include <linux/err.h> > +#include <linux/init.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/pinctrl/pinctrl.h> > + > +#include "pinctrl-imx1.h" > + > +#define PAD_ID(port, pin) (port*32 + pin) > +#define PA 0 > +#define PB 1 > +#define PC 2 > +#define PD 3 > +#define PE 4 > +#define PF 5 > + > +enum imx27_pads { > + MX27_PAD_USBH2_CLK = PAD_ID(PA, 0), > + MX27_PAD_USBH2_DIR = PAD_ID(PA, 1), > + MX27_PAD_USBH2_DATA7 = PAD_ID(PA, 2), > + MX27_PAD_USBH2_NXT = PAD_ID(PA, 3), > + MX27_PAD_USBH2_STP = PAD_ID(PA, 4), > + MX27_PAD_LSCLK = PAD_ID(PA, 5), > + MX27_PAD_LD0 = PAD_ID(PA, 6), > + MX27_PAD_LD1 = PAD_ID(PA, 7), > + MX27_PAD_LD2 = PAD_ID(PA, 8), > + MX27_PAD_LD3 = PAD_ID(PA, 9), > + MX27_PAD_LD4 = PAD_ID(PA, 10), > + MX27_PAD_LD5 = PAD_ID(PA, 11), > + MX27_PAD_LD6 = PAD_ID(PA, 12), > + MX27_PAD_LD7 = PAD_ID(PA, 13), > + MX27_PAD_LD8 = PAD_ID(PA, 14), > + MX27_PAD_LD9 = PAD_ID(PA, 15), > + MX27_PAD_LD10 = PAD_ID(PA, 16), > + MX27_PAD_LD11 = PAD_ID(PA, 17), > + MX27_PAD_LD12 = PAD_ID(PA, 18), > + MX27_PAD_LD13 = PAD_ID(PA, 19), > + MX27_PAD_LD14 = PAD_ID(PA, 20), > + MX27_PAD_LD15 = PAD_ID(PA, 21), > + MX27_PAD_LD16 = PAD_ID(PA, 22), > + MX27_PAD_LD17 = PAD_ID(PA, 23), > + MX27_PAD_REV = PAD_ID(PA, 24), > + MX27_PAD_CLS = PAD_ID(PA, 25), > + MX27_PAD_PS = PAD_ID(PA, 26), > + MX27_PAD_SPL_SPR = PAD_ID(PA, 27), > + MX27_PAD_HSYNC = PAD_ID(PA, 28), > + MX27_PAD_VSYNC = PAD_ID(PA, 29), > + MX27_PAD_CONTRAST = PAD_ID(PA, 30), > + MX27_PAD_OE_ACD = PAD_ID(PA, 31), > + > + MX27_PAD_UNUSED0 = PAD_ID(PB, 0), > + MX27_PAD_UNUSED1 = PAD_ID(PB, 1), > + MX27_PAD_UNUSED2 = PAD_ID(PB, 2), > + MX27_PAD_UNUSED3 = PAD_ID(PB, 3), > + MX27_PAD_SD2_D0 = PAD_ID(PB, 4), > + MX27_PAD_SD2_D1 = PAD_ID(PB, 5), > + MX27_PAD_SD2_D2 = PAD_ID(PB, 6), > + MX27_PAD_SD2_D3 = PAD_ID(PB, 7), > + MX27_PAD_SD2_CMD = PAD_ID(PB, 8), > + MX27_PAD_SD2_CLK = PAD_ID(PB, 9), > + MX27_PAD_CSI_D0 = PAD_ID(PB, 10), > + MX27_PAD_CSI_D1 = PAD_ID(PB, 11), > + MX27_PAD_CSI_D2 = PAD_ID(PB, 12), > + MX27_PAD_CSI_D3 = PAD_ID(PB, 13), > + MX27_PAD_CSI_D4 = PAD_ID(PB, 14), > + MX27_PAD_CSI_MCLK = PAD_ID(PB, 15), > + MX27_PAD_CSI_PIXCLK = PAD_ID(PB, 16), > + MX27_PAD_CSI_D5 = PAD_ID(PB, 17), > + MX27_PAD_CSI_D6 = PAD_ID(PB, 18), > + MX27_PAD_CSI_D7 = PAD_ID(PB, 19), > + MX27_PAD_CSI_VSYNC = PAD_ID(PB, 20), > + MX27_PAD_CSI_HSYNC = PAD_ID(PB, 21), > + MX27_PAD_USBH1_SUSP = PAD_ID(PB, 22), > + MX27_PAD_USB_PWR = PAD_ID(PB, 23), > + MX27_PAD_USB_OC_B = PAD_ID(PB, 24), > + MX27_PAD_USBH1_RCV = PAD_ID(PB, 25), > + MX27_PAD_USBH1_FS = PAD_ID(PB, 26), > + MX27_PAD_USBH1_OE_B = PAD_ID(PB, 27), > + MX27_PAD_USBH1_TXDM = PAD_ID(PB, 28), > + MX27_PAD_USBH1_TXDP = PAD_ID(PB, 29), > + MX27_PAD_USBH1_RXDM = PAD_ID(PB, 30), > + MX27_PAD_USBH1_RXDP = PAD_ID(PB, 31), > + > + MX27_PAD_UNUSED4 = PAD_ID(PC, 0), > + MX27_PAD_UNUSED5 = PAD_ID(PC, 1), > + MX27_PAD_UNUSED6 = PAD_ID(PC, 2), > + MX27_PAD_UNUSED7 = PAD_ID(PC, 3), > + MX27_PAD_UNUSED8 = PAD_ID(PC, 4), > + MX27_PAD_I2C2_SDA = PAD_ID(PC, 5), > + MX27_PAD_I2C2_SCL = PAD_ID(PC, 6), > + MX27_PAD_USBOTG_DATA5 = PAD_ID(PC, 7), > + MX27_PAD_USBOTG_DATA6 = PAD_ID(PC, 8), > + MX27_PAD_USBOTG_DATA0 = PAD_ID(PC, 9), > + MX27_PAD_USBOTG_DATA2 = PAD_ID(PC, 10), > + MX27_PAD_USBOTG_DATA1 = PAD_ID(PC, 11), > + MX27_PAD_USBOTG_DATA4 = PAD_ID(PC, 12), > + MX27_PAD_USBOTG_DATA3 = PAD_ID(PC, 13), > + MX27_PAD_TOUT = PAD_ID(PC, 14), > + MX27_PAD_TIN = PAD_ID(PC, 15), > + MX27_PAD_SSI4_FS = PAD_ID(PC, 16), > + MX27_PAD_SSI4_RXDAT = PAD_ID(PC, 17), > + MX27_PAD_SSI4_TXDAT = PAD_ID(PC, 18), > + MX27_PAD_SSI4_CLK = PAD_ID(PC, 19), > + MX27_PAD_SSI1_FS = PAD_ID(PC, 20), > + MX27_PAD_SSI1_RXDAT = PAD_ID(PC, 21), > + MX27_PAD_SSI1_TXDAT = PAD_ID(PC, 22), > + MX27_PAD_SSI1_CLK = PAD_ID(PC, 23), > + MX27_PAD_SSI2_FS = PAD_ID(PC, 24), > + MX27_PAD_SSI2_RXDAT = PAD_ID(PC, 25), > + MX27_PAD_SSI2_TXDAT = PAD_ID(PC, 26), > + MX27_PAD_SSI2_CLK = PAD_ID(PC, 27), > + MX27_PAD_SSI3_FS = PAD_ID(PC, 28), > + MX27_PAD_SSI3_RXDAT = PAD_ID(PC, 29), > + MX27_PAD_SSI3_TXDAT = PAD_ID(PC, 30), > + MX27_PAD_SSI3_CLK = PAD_ID(PC, 31), > + > + MX27_PAD_SD3_CMD = PAD_ID(PD, 0), > + MX27_PAD_SD3_CLK = PAD_ID(PD, 1), > + MX27_PAD_ATA_DATA0 = PAD_ID(PD, 2), > + MX27_PAD_ATA_DATA1 = PAD_ID(PD, 3), > + MX27_PAD_ATA_DATA2 = PAD_ID(PD, 4), > + MX27_PAD_ATA_DATA3 = PAD_ID(PD, 5), > + MX27_PAD_ATA_DATA4 = PAD_ID(PD, 6), > + MX27_PAD_ATA_DATA5 = PAD_ID(PD, 7), > + MX27_PAD_ATA_DATA6 = PAD_ID(PD, 8), > + MX27_PAD_ATA_DATA7 = PAD_ID(PD, 9), > + MX27_PAD_ATA_DATA8 = PAD_ID(PD, 10), > + MX27_PAD_ATA_DATA9 = PAD_ID(PD, 11), > + MX27_PAD_ATA_DATA10 = PAD_ID(PD, 12), > + MX27_PAD_ATA_DATA11 = PAD_ID(PD, 13), > + MX27_PAD_ATA_DATA12 = PAD_ID(PD, 14), > + MX27_PAD_ATA_DATA13 = PAD_ID(PD, 15), > + MX27_PAD_ATA_DATA14 = PAD_ID(PD, 16), > + MX27_PAD_I2C_DATA = PAD_ID(PD, 17), > + MX27_PAD_I2C_CLK = PAD_ID(PD, 18), > + MX27_PAD_CSPI2_SS2 = PAD_ID(PD, 19), > + MX27_PAD_CSPI2_SS1 = PAD_ID(PD, 20), > + MX27_PAD_CSPI2_SS0 = PAD_ID(PD, 21), > + MX27_PAD_CSPI2_SCLK = PAD_ID(PD, 22), > + MX27_PAD_CSPI2_MISO = PAD_ID(PD, 23), > + MX27_PAD_CSPI2_MOSI = PAD_ID(PD, 24), > + MX27_PAD_CSPI1_RDY = PAD_ID(PD, 25), > + MX27_PAD_CSPI1_SS2 = PAD_ID(PD, 26), > + MX27_PAD_CSPI1_SS1 = PAD_ID(PD, 27), > + MX27_PAD_CSPI1_SS0 = PAD_ID(PD, 28), > + MX27_PAD_CSPI1_SCLK = PAD_ID(PD, 29), > + MX27_PAD_CSPI1_MISO = PAD_ID(PD, 30), > + MX27_PAD_CSPI1_MOSI = PAD_ID(PD, 31), > + > + MX27_PAD_USBOTG_NXT = PAD_ID(PE, 0), > + MX27_PAD_USBOTG_STP = PAD_ID(PE, 1), > + MX27_PAD_USBOTG_DIR = PAD_ID(PE, 2), > + MX27_PAD_UART2_CTS = PAD_ID(PE, 3), > + MX27_PAD_UART2_RTS = PAD_ID(PE, 4), > + MX27_PAD_PWMO = PAD_ID(PE, 5), > + MX27_PAD_UART2_TXD = PAD_ID(PE, 6), > + MX27_PAD_UART2_RXD = PAD_ID(PE, 7), > + MX27_PAD_UART3_TXD = PAD_ID(PE, 8), > + MX27_PAD_UART3_RXD = PAD_ID(PE, 9), > + MX27_PAD_UART3_CTS = PAD_ID(PE, 10), > + MX27_PAD_UART3_RTS = PAD_ID(PE, 11), > + MX27_PAD_UART1_TXD = PAD_ID(PE, 12), > + MX27_PAD_UART1_RXD = PAD_ID(PE, 13), > + MX27_PAD_UART1_CTS = PAD_ID(PE, 14), > + MX27_PAD_UART1_RTS = PAD_ID(PE, 15), > + MX27_PAD_RTCK = PAD_ID(PE, 16), > + MX27_PAD_RESET_OUT_B = PAD_ID(PE, 17), > + MX27_PAD_SD1_D0 = PAD_ID(PE, 18), > + MX27_PAD_SD1_D1 = PAD_ID(PE, 19), > + MX27_PAD_SD1_D2 = PAD_ID(PE, 20), > + MX27_PAD_SD1_D3 = PAD_ID(PE, 21), > + MX27_PAD_SD1_CMD = PAD_ID(PE, 22), > + MX27_PAD_SD1_CLK = PAD_ID(PE, 23), > + MX27_PAD_USBOTG_CLK = PAD_ID(PE, 24), > + MX27_PAD_USBOTG_DATA7 = PAD_ID(PE, 25), > + MX27_PAD_UNUSED9 = PAD_ID(PE, 26), > + MX27_PAD_UNUSED10 = PAD_ID(PE, 27), > + MX27_PAD_UNUSED11 = PAD_ID(PE, 28), > + MX27_PAD_UNUSED12 = PAD_ID(PE, 29), > + MX27_PAD_UNUSED13 = PAD_ID(PE, 30), > + MX27_PAD_UNUSED14 = PAD_ID(PE, 31), > + > + MX27_PAD_NFRB = PAD_ID(PF, 0), > + MX27_PAD_NFCLE = PAD_ID(PF, 1), > + MX27_PAD_NFWP_B = PAD_ID(PF, 2), > + MX27_PAD_NFCE_B = PAD_ID(PF, 3), > + MX27_PAD_NFALE = PAD_ID(PF, 4), > + MX27_PAD_NFRE_B = PAD_ID(PF, 5), > + MX27_PAD_NFWE_B = PAD_ID(PF, 6), > + MX27_PAD_PC_POE = PAD_ID(PF, 7), > + MX27_PAD_PC_RW_B = PAD_ID(PF, 8), > + MX27_PAD_IOIS16 = PAD_ID(PF, 9), > + MX27_PAD_PC_RST = PAD_ID(PF, 10), > + MX27_PAD_PC_BVD2 = PAD_ID(PF, 11), > + MX27_PAD_PC_BVD1 = PAD_ID(PF, 12), > + MX27_PAD_PC_VS2 = PAD_ID(PF, 13), > + MX27_PAD_PC_VS1 = PAD_ID(PF, 14), > + MX27_PAD_CLKO = PAD_ID(PF, 15), > + MX27_PAD_PC_PWRON = PAD_ID(PF, 16), > + MX27_PAD_PC_READY = PAD_ID(PF, 17), > + MX27_PAD_PC_WAIT_B = PAD_ID(PF, 18), > + MX27_PAD_PC_CD2_B = PAD_ID(PF, 19), > + MX27_PAD_PC_CD1_B = PAD_ID(PF, 20), > + MX27_PAD_CS4_B = PAD_ID(PF, 21), > + MX27_PAD_CS5_B = PAD_ID(PF, 22), > + MX27_PAD_ATA_DATA15 = PAD_ID(PF, 23), > + MX27_PAD_UNUSED15 = PAD_ID(PF, 24), > + MX27_PAD_UNUSED16 = PAD_ID(PF, 25), > + MX27_PAD_UNUSED17 = PAD_ID(PF, 26), > + MX27_PAD_UNUSED18 = PAD_ID(PF, 27), > + MX27_PAD_UNUSED19 = PAD_ID(PF, 28), > + MX27_PAD_UNUSED20 = PAD_ID(PF, 29), > + MX27_PAD_UNUSED21 = PAD_ID(PF, 30), > + MX27_PAD_UNUSED22 = PAD_ID(PF, 31), > +}; > + > +/* Pad names for the pinmux subsystem */ > +static const struct pinctrl_pin_desc imx27_pinctrl_pads[] = { > + IMX_PINCTRL_PIN(MX27_PAD_USBH2_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_USBH2_DIR), > + IMX_PINCTRL_PIN(MX27_PAD_USBH2_DATA7), > + IMX_PINCTRL_PIN(MX27_PAD_USBH2_NXT), > + IMX_PINCTRL_PIN(MX27_PAD_USBH2_STP), > + IMX_PINCTRL_PIN(MX27_PAD_LSCLK), > + IMX_PINCTRL_PIN(MX27_PAD_LD0), > + IMX_PINCTRL_PIN(MX27_PAD_LD1), > + IMX_PINCTRL_PIN(MX27_PAD_LD2), > + IMX_PINCTRL_PIN(MX27_PAD_LD3), > + IMX_PINCTRL_PIN(MX27_PAD_LD4), > + IMX_PINCTRL_PIN(MX27_PAD_LD5), > + IMX_PINCTRL_PIN(MX27_PAD_LD6), > + IMX_PINCTRL_PIN(MX27_PAD_LD7), > + IMX_PINCTRL_PIN(MX27_PAD_LD8), > + IMX_PINCTRL_PIN(MX27_PAD_LD9), > + IMX_PINCTRL_PIN(MX27_PAD_LD10), > + IMX_PINCTRL_PIN(MX27_PAD_LD11), > + IMX_PINCTRL_PIN(MX27_PAD_LD12), > + IMX_PINCTRL_PIN(MX27_PAD_LD13), > + IMX_PINCTRL_PIN(MX27_PAD_LD14), > + IMX_PINCTRL_PIN(MX27_PAD_LD15), > + IMX_PINCTRL_PIN(MX27_PAD_LD16), > + IMX_PINCTRL_PIN(MX27_PAD_LD17), > + IMX_PINCTRL_PIN(MX27_PAD_REV), > + IMX_PINCTRL_PIN(MX27_PAD_CLS), > + IMX_PINCTRL_PIN(MX27_PAD_PS), > + IMX_PINCTRL_PIN(MX27_PAD_SPL_SPR), > + IMX_PINCTRL_PIN(MX27_PAD_HSYNC), > + IMX_PINCTRL_PIN(MX27_PAD_VSYNC), > + IMX_PINCTRL_PIN(MX27_PAD_CONTRAST), > + IMX_PINCTRL_PIN(MX27_PAD_OE_ACD), > + > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED0), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED1), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED2), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED3), > + IMX_PINCTRL_PIN(MX27_PAD_SD2_D0), > + IMX_PINCTRL_PIN(MX27_PAD_SD2_D1), > + IMX_PINCTRL_PIN(MX27_PAD_SD2_D2), > + IMX_PINCTRL_PIN(MX27_PAD_SD2_D3), > + IMX_PINCTRL_PIN(MX27_PAD_SD2_CMD), > + IMX_PINCTRL_PIN(MX27_PAD_SD2_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D0), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D1), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D2), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D3), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D4), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_MCLK), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_PIXCLK), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D5), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D6), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_D7), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_VSYNC), > + IMX_PINCTRL_PIN(MX27_PAD_CSI_HSYNC), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_SUSP), > + IMX_PINCTRL_PIN(MX27_PAD_USB_PWR), > + IMX_PINCTRL_PIN(MX27_PAD_USB_OC_B), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RCV), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_FS), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_OE_B), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_TXDM), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_TXDP), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RXDM), > + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RXDP), > + > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED4), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED5), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED6), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED7), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED8), > + IMX_PINCTRL_PIN(MX27_PAD_I2C2_SDA), > + IMX_PINCTRL_PIN(MX27_PAD_I2C2_SCL), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA5), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA6), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA0), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA2), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA1), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA4), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA3), > + IMX_PINCTRL_PIN(MX27_PAD_TOUT), > + IMX_PINCTRL_PIN(MX27_PAD_TIN), > + IMX_PINCTRL_PIN(MX27_PAD_SSI4_FS), > + IMX_PINCTRL_PIN(MX27_PAD_SSI4_RXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI4_TXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI4_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_SSI1_FS), > + IMX_PINCTRL_PIN(MX27_PAD_SSI1_RXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI1_TXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI1_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_SSI2_FS), > + IMX_PINCTRL_PIN(MX27_PAD_SSI2_RXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI2_TXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI2_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_SSI3_FS), > + IMX_PINCTRL_PIN(MX27_PAD_SSI3_RXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI3_TXDAT), > + IMX_PINCTRL_PIN(MX27_PAD_SSI3_CLK), > + > + IMX_PINCTRL_PIN(MX27_PAD_SD3_CMD), > + IMX_PINCTRL_PIN(MX27_PAD_SD3_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA0), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA1), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA2), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA3), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA4), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA5), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA6), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA7), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA8), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA9), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA10), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA11), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA12), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA13), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA14), > + IMX_PINCTRL_PIN(MX27_PAD_I2C_DATA), > + IMX_PINCTRL_PIN(MX27_PAD_I2C_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS2), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS1), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS0), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SCLK), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_MISO), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_MOSI), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_RDY), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS2), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS1), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS0), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SCLK), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_MISO), > + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_MOSI), > + > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_NXT), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_STP), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DIR), > + IMX_PINCTRL_PIN(MX27_PAD_UART2_CTS), > + IMX_PINCTRL_PIN(MX27_PAD_UART2_RTS), > + IMX_PINCTRL_PIN(MX27_PAD_PWMO), > + IMX_PINCTRL_PIN(MX27_PAD_UART2_TXD), > + IMX_PINCTRL_PIN(MX27_PAD_UART2_RXD), > + IMX_PINCTRL_PIN(MX27_PAD_UART3_TXD), > + IMX_PINCTRL_PIN(MX27_PAD_UART3_RXD), > + IMX_PINCTRL_PIN(MX27_PAD_UART3_CTS), > + IMX_PINCTRL_PIN(MX27_PAD_UART3_RTS), > + IMX_PINCTRL_PIN(MX27_PAD_UART1_TXD), > + IMX_PINCTRL_PIN(MX27_PAD_UART1_RXD), > + IMX_PINCTRL_PIN(MX27_PAD_UART1_CTS), > + IMX_PINCTRL_PIN(MX27_PAD_UART1_RTS), > + IMX_PINCTRL_PIN(MX27_PAD_RTCK), > + IMX_PINCTRL_PIN(MX27_PAD_RESET_OUT_B), > + IMX_PINCTRL_PIN(MX27_PAD_SD1_D0), > + IMX_PINCTRL_PIN(MX27_PAD_SD1_D1), > + IMX_PINCTRL_PIN(MX27_PAD_SD1_D2), > + IMX_PINCTRL_PIN(MX27_PAD_SD1_D3), > + IMX_PINCTRL_PIN(MX27_PAD_SD1_CMD), > + IMX_PINCTRL_PIN(MX27_PAD_SD1_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_CLK), > + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA7), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED9), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED10), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED11), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED12), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED13), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED14), > + > + IMX_PINCTRL_PIN(MX27_PAD_NFRB), > + IMX_PINCTRL_PIN(MX27_PAD_NFCLE), > + IMX_PINCTRL_PIN(MX27_PAD_NFWP_B), > + IMX_PINCTRL_PIN(MX27_PAD_NFCE_B), > + IMX_PINCTRL_PIN(MX27_PAD_NFALE), > + IMX_PINCTRL_PIN(MX27_PAD_NFRE_B), > + IMX_PINCTRL_PIN(MX27_PAD_NFWE_B), > + IMX_PINCTRL_PIN(MX27_PAD_PC_POE), > + IMX_PINCTRL_PIN(MX27_PAD_PC_RW_B), > + IMX_PINCTRL_PIN(MX27_PAD_IOIS16), > + IMX_PINCTRL_PIN(MX27_PAD_PC_RST), > + IMX_PINCTRL_PIN(MX27_PAD_PC_BVD2), > + IMX_PINCTRL_PIN(MX27_PAD_PC_BVD1), > + IMX_PINCTRL_PIN(MX27_PAD_PC_VS2), > + IMX_PINCTRL_PIN(MX27_PAD_PC_VS1), > + IMX_PINCTRL_PIN(MX27_PAD_CLKO), > + IMX_PINCTRL_PIN(MX27_PAD_PC_PWRON), > + IMX_PINCTRL_PIN(MX27_PAD_PC_READY), > + IMX_PINCTRL_PIN(MX27_PAD_PC_WAIT_B), > + IMX_PINCTRL_PIN(MX27_PAD_PC_CD2_B), > + IMX_PINCTRL_PIN(MX27_PAD_PC_CD1_B), > + IMX_PINCTRL_PIN(MX27_PAD_CS4_B), > + IMX_PINCTRL_PIN(MX27_PAD_CS5_B), > + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA15), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED15), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED16), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED17), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED18), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED19), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED20), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED21), > + IMX_PINCTRL_PIN(MX27_PAD_UNUSED22), > +}; > + > +static struct imx1_pinctrl_soc_info imx27_pinctrl_info = { > + .pins = imx27_pinctrl_pads, > + .npins = ARRAY_SIZE(imx27_pinctrl_pads), > +}; > + > +static struct of_device_id imx27_pinctrl_of_match[] = { > + { .compatible = "fsl,imx27-iomuxc", }, > + { /* sentinel */ } > +}; > + > +struct imx27_pinctrl_private { > + int num_gpio_childs; > + struct platform_device **gpio_dev; > + struct mxc_gpio_platform_data *gpio_pdata; > +}; > + > +static int imx27_pinctrl_probe(struct platform_device *pdev) > +{ > + return imx1_pinctrl_core_probe(pdev, &imx27_pinctrl_info); > +} > + > +static struct platform_driver imx27_pinctrl_driver = { > + .driver = { > + .name = "imx27-pinctrl", > + .owner = THIS_MODULE, > + .of_match_table = of_match_ptr(imx27_pinctrl_of_match), > + }, > + .probe = imx27_pinctrl_probe, > + .remove = imx1_pinctrl_core_remove, > +}; > + > +static int __init imx27_pinctrl_init(void) > +{ > + return platform_driver_register(&imx27_pinctrl_driver); > +} > +arch_initcall(imx27_pinctrl_init); > + > +static void __exit imx27_pinctrl_exit(void) > +{ > + platform_driver_unregister(&imx27_pinctrl_driver); > +} > +module_exit(imx27_pinctrl_exit); > +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>"); > +MODULE_DESCRIPTION("Freescale IMX27 pinctrl driver"); > +MODULE_LICENSE("GPL v2"); > -- > 1.8.4.rc3 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel at lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v4 3/7] ARM: dts: imx27 pin functions 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 1/7] pinctrl: imx1 core driver Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 2/7] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 4/7] ARM: dts: imx27 pinctrl Markus Pargmann ` (4 subsequent siblings) 7 siblings, 0 replies; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27-pinfunc.h | 524 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 524 insertions(+) create mode 100644 arch/arm/boot/dts/imx27-pinfunc.h diff --git a/arch/arm/boot/dts/imx27-pinfunc.h b/arch/arm/boot/dts/imx27-pinfunc.h new file mode 100644 index 0000000..32bfcc2 --- /dev/null +++ b/arch/arm/boot/dts/imx27-pinfunc.h @@ -0,0 +1,524 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __DTS_IMX27_PINFUNC_H +#define __DTS_IMX27_PINFUNC_H + +/* + * The pin function ID is a tuple of + * <pin mux_id> + * mux_id consists of + * function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) + * + * function: 0 - Primary function + * 1 - Alternate function + * 2 - GPIO + * direction: 0 - Input + * 1 - Output + * gpio_oconf: 0 - A_IN + * 1 - B_IN + * 2 - C_IN + * 3 - Data Register + * gpio_iconfa/b: 0 - GPIO_IN + * 1 - Interrupt Status Register + * 2 - 0 + * 3 - 1 + * + * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable + * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin + * number on the specific port (between 0 and 31). + */ + +#define MX27_PAD_USBH2_CLK__USBH2_CLK 0x00 0x000 +#define MX27_PAD_USBH2_CLK__GPIO1_0 0x00 0x036 +#define MX27_PAD_USBH2_DIR__USBH2_DIR 0x01 0x000 +#define MX27_PAD_USBH2_DIR__GPIO1_1 0x01 0x036 +#define MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x02 0x004 +#define MX27_PAD_USBH2_DATA7__GPIO1_2 0x02 0x036 +#define MX27_PAD_USBH2_NXT__USBH2_NXT 0x03 0x000 +#define MX27_PAD_USBH2_NXT__GPIO1_3 0x03 0x036 +#define MX27_PAD_USBH2_STP__USBH2_STP 0x04 0x004 +#define MX27_PAD_USBH2_STP__GPIO1_4 0x04 0x036 +#define MX27_PAD_LSCLK__LSCLK 0x05 0x004 +#define MX27_PAD_LSCLK__GPIO1_5 0x05 0x036 +#define MX27_PAD_LD0__LD0 0x06 0x004 +#define MX27_PAD_LD0__GPIO1_6 0x06 0x036 +#define MX27_PAD_LD1__LD1 0x07 0x004 +#define MX27_PAD_LD1__GPIO1_7 0x07 0x036 +#define MX27_PAD_LD2__LD2 0x08 0x004 +#define MX27_PAD_LD2__GPIO1_8 0x08 0x036 +#define MX27_PAD_LD3__LD3 0x09 0x004 +#define MX27_PAD_LD3__GPIO1_9 0x09 0x036 +#define MX27_PAD_LD4__LD4 0x0a 0x004 +#define MX27_PAD_LD4__GPIO1_10 0x0a 0x036 +#define MX27_PAD_LD5__LD5 0x0b 0x004 +#define MX27_PAD_LD5__GPIO1_11 0x0b 0x036 +#define MX27_PAD_LD6__LD6 0x0c 0x004 +#define MX27_PAD_LD6__GPIO1_12 0x0c 0x036 +#define MX27_PAD_LD7__LD7 0x0d 0x004 +#define MX27_PAD_LD7__GPIO1_13 0x0d 0x036 +#define MX27_PAD_LD8__LD8 0x0e 0x004 +#define MX27_PAD_LD8__GPIO1_14 0x0e 0x036 +#define MX27_PAD_LD9__LD9 0x0f 0x004 +#define MX27_PAD_LD9__GPIO1_15 0x0f 0x036 +#define MX27_PAD_LD10__LD10 0x10 0x004 +#define MX27_PAD_LD10__GPIO1_16 0x10 0x036 +#define MX27_PAD_LD11__LD11 0x11 0x004 +#define MX27_PAD_LD11__GPIO1_17 0x11 0x036 +#define MX27_PAD_LD12__LD12 0x12 0x004 +#define MX27_PAD_LD12__GPIO1_18 0x12 0x036 +#define MX27_PAD_LD13__LD13 0x13 0x004 +#define MX27_PAD_LD13__GPIO1_19 0x13 0x036 +#define MX27_PAD_LD14__LD14 0x14 0x004 +#define MX27_PAD_LD14__GPIO1_20 0x14 0x036 +#define MX27_PAD_LD15__LD15 0x15 0x004 +#define MX27_PAD_LD15__GPIO1_21 0x15 0x036 +#define MX27_PAD_LD16__LD16 0x16 0x004 +#define MX27_PAD_LD16__GPIO1_22 0x16 0x036 +#define MX27_PAD_LD17__LD17 0x17 0x004 +#define MX27_PAD_LD17__GPIO1_23 0x17 0x036 +#define MX27_PAD_REV__REV 0x18 0x004 +#define MX27_PAD_REV__GPIO1_24 0x18 0x036 +#define MX27_PAD_CLS__CLS 0x19 0x004 +#define MX27_PAD_CLS__GPIO1_25 0x19 0x036 +#define MX27_PAD_PS__PS 0x1a 0x004 +#define MX27_PAD_PS__GPIO1_26 0x1a 0x036 +#define MX27_PAD_SPL_SPR__SPL_SPR 0x1b 0x004 +#define MX27_PAD_SPL_SPR__GPIO1_27 0x1b 0x036 +#define MX27_PAD_HSYNC__HSYNC 0x1c 0x004 +#define MX27_PAD_HSYNC__GPIO1_28 0x1c 0x036 +#define MX27_PAD_VSYNC__VSYNC 0x1d 0x004 +#define MX27_PAD_VSYNC__GPIO1_29 0x1d 0x036 +#define MX27_PAD_CONTRAST__CONTRAST 0x1e 0x004 +#define MX27_PAD_CONTRAST__GPIO1_30 0x1e 0x036 +#define MX27_PAD_OE_ACD__OE_ACD 0x1f 0x004 +#define MX27_PAD_OE_ACD__GPIO1_31 0x1f 0x036 +#define MX27_PAD_UNUSED0__UNUSED0 0x20 0x004 +#define MX27_PAD_UNUSED0__GPIO2_0 0x20 0x036 +#define MX27_PAD_UNUSED1__UNUSED1 0x21 0x004 +#define MX27_PAD_UNUSED1__GPIO2_1 0x21 0x036 +#define MX27_PAD_UNUSED2__UNUSED2 0x22 0x004 +#define MX27_PAD_UNUSED2__GPIO2_2 0x22 0x036 +#define MX27_PAD_UNUSED3__UNUSED3 0x23 0x004 +#define MX27_PAD_UNUSED3__GPIO2_3 0x23 0x036 +#define MX27_PAD_SD2_D0__SD2_D0 0x24 0x004 +#define MX27_PAD_SD2_D0__MSHC_DATA0 0x24 0x005 +#define MX27_PAD_SD2_D0__GPIO2_4 0x24 0x036 +#define MX27_PAD_SD2_D1__SD2_D1 0x25 0x004 +#define MX27_PAD_SD2_D1__MSHC_DATA1 0x25 0x005 +#define MX27_PAD_SD2_D1__GPIO2_5 0x25 0x036 +#define MX27_PAD_SD2_D2__SD2_D2 0x26 0x004 +#define MX27_PAD_SD2_D2__MSHC_DATA2 0x26 0x005 +#define MX27_PAD_SD2_D2__GPIO2_6 0x26 0x036 +#define MX27_PAD_SD2_D3__SD2_D3 0x27 0x004 +#define MX27_PAD_SD2_D3__MSHC_DATA3 0x27 0x005 +#define MX27_PAD_SD2_D3__GPIO2_7 0x27 0x036 +#define MX27_PAD_SD2_CMD__SD2_CMD 0x28 0x004 +#define MX27_PAD_SD2_CMD__MSHC_BS 0x28 0x005 +#define MX27_PAD_SD2_CMD__GPIO2_8 0x28 0x036 +#define MX27_PAD_SD2_CLK__SD2_CLK 0x29 0x004 +#define MX27_PAD_SD2_CLK__MSHC_SCLK 0x29 0x005 +#define MX27_PAD_SD2_CLK__GPIO2_9 0x29 0x036 +#define MX27_PAD_CSI_D0__CSI_D0 0x2a 0x000 +#define MX27_PAD_CSI_D0__UART6_TXD 0x2a 0x005 +#define MX27_PAD_CSI_D0__GPIO2_10 0x2a 0x036 +#define MX27_PAD_CSI_D1__CSI_D1 0x2b 0x000 +#define MX27_PAD_CSI_D1__UART6_RXD 0x2b 0x001 +#define MX27_PAD_CSI_D1__GPIO2_11 0x2b 0x036 +#define MX27_PAD_CSI_D2__CSI_D2 0x2c 0x000 +#define MX27_PAD_CSI_D2__UART6_CTS 0x2c 0x005 +#define MX27_PAD_CSI_D2__GPIO2_12 0x2c 0x036 +#define MX27_PAD_CSI_D3__CSI_D3 0x2d 0x000 +#define MX27_PAD_CSI_D3__UART6_RTS 0x2d 0x001 +#define MX27_PAD_CSI_D3__GPIO2_13 0x2d 0x036 +#define MX27_PAD_CSI_D4__CSI_D4 0x2e 0x000 +#define MX27_PAD_CSI_D4__GPIO2_14 0x2e 0x036 +#define MX27_PAD_CSI_MCLK__CSI_MCLK 0x2f 0x004 +#define MX27_PAD_CSI_MCLK__GPIO2_15 0x2f 0x036 +#define MX27_PAD_CSI_PIXCLK__CSI_PIXCLK 0x30 0x000 +#define MX27_PAD_CSI_PIXCLK__GPIO2_16 0x30 0x036 +#define MX27_PAD_CSI_D5__CSI_D5 0x31 0x000 +#define MX27_PAD_CSI_D5__GPIO2_17 0x31 0x036 +#define MX27_PAD_CSI_D6__CSI_D6 0x32 0x000 +#define MX27_PAD_CSI_D6__UART5_TXD 0x32 0x005 +#define MX27_PAD_CSI_D6__GPIO2_18 0x32 0x036 +#define MX27_PAD_CSI_D7__CSI_D7 0x33 0x000 +#define MX27_PAD_CSI_D7__UART5_RXD 0x33 0x001 +#define MX27_PAD_CSI_D7__GPIO2_19 0x33 0x036 +#define MX27_PAD_CSI_VSYNC__CSI_VSYNC 0x34 0x000 +#define MX27_PAD_CSI_VSYNC__UART5_CTS 0x34 0x005 +#define MX27_PAD_CSI_VSYNC__GPIO2_20 0x34 0x036 +#define MX27_PAD_CSI_HSYNC__CSI_HSYNC 0x35 0x000 +#define MX27_PAD_CSI_HSYNC__UART5_RTS 0x35 0x001 +#define MX27_PAD_CSI_HSYNC__GPIO2_21 0x35 0x036 +#define MX27_PAD_USBH1_SUSP__USBH1_SUSP 0x36 0x004 +#define MX27_PAD_USBH1_SUSP__GPIO2_22 0x36 0x036 +#define MX27_PAD_USB_PWR__USB_PWR 0x37 0x004 +#define MX27_PAD_USB_PWR__GPIO2_23 0x37 0x036 +#define MX27_PAD_USB_OC_B__USB_OC_B 0x38 0x000 +#define MX27_PAD_USB_OC_B__GPIO2_24 0x38 0x036 +#define MX27_PAD_USBH1_RCV__USBH1_RCV 0x39 0x004 +#define MX27_PAD_USBH1_RCV__GPIO2_25 0x39 0x036 +#define MX27_PAD_USBH1_FS__USBH1_FS 0x3a 0x004 +#define MX27_PAD_USBH1_FS__UART4_RTS 0x3a 0x001 +#define MX27_PAD_USBH1_FS__GPIO2_26 0x3a 0x036 +#define MX27_PAD_USBH1_OE_B__USBH1_OE_B 0x3b 0x004 +#define MX27_PAD_USBH1_OE_B__GPIO2_27 0x3b 0x036 +#define MX27_PAD_USBH1_TXDM__USBH1_TXDM 0x3c 0x004 +#define MX27_PAD_USBH1_TXDM__UART4_TXD 0x3c 0x005 +#define MX27_PAD_USBH1_TXDM__GPIO2_28 0x3c 0x036 +#define MX27_PAD_USBH1_TXDP__USBH1_TXDP 0x3d 0x004 +#define MX27_PAD_USBH1_TXDP__UART4_CTS 0x3d 0x005 +#define MX27_PAD_USBH1_TXDP__GPIO2_29 0x3d 0x036 +#define MX27_PAD_USBH1_RXDM__USBH1_RXDM 0x3e 0x004 +#define MX27_PAD_USBH1_RXDM__GPIO2_30 0x3e 0x036 +#define MX27_PAD_USBH1_RXDP__USBH1_RXDP 0x3f 0x004 +#define MX27_PAD_USBH1_RXDP__UART4_RXD 0x3f 0x001 +#define MX27_PAD_USBH1_RXDP__GPIO2_31 0x3f 0x036 +#define MX27_PAD_UNUSED4__UNUSED4 0x40 0x004 +#define MX27_PAD_UNUSED4__GPIO3_0 0x40 0x036 +#define MX27_PAD_UNUSED5__UNUSED5 0x41 0x004 +#define MX27_PAD_UNUSED5__GPIO3_1 0x41 0x036 +#define MX27_PAD_UNUSED6__UNUSED6 0x42 0x004 +#define MX27_PAD_UNUSED6__GPIO3_2 0x42 0x036 +#define MX27_PAD_UNUSED7__UNUSED7 0x43 0x004 +#define MX27_PAD_UNUSED7__GPIO3_3 0x43 0x036 +#define MX27_PAD_UNUSED8__UNUSED8 0x44 0x004 +#define MX27_PAD_UNUSED8__GPIO3_4 0x44 0x036 +#define MX27_PAD_I2C2_SDA__I2C2_SDA 0x45 0x004 +#define MX27_PAD_I2C2_SDA__GPIO3_5 0x45 0x036 +#define MX27_PAD_I2C2_SCL__I2C2_SCL 0x46 0x004 +#define MX27_PAD_I2C2_SCL__GPIO3_6 0x46 0x036 +#define MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x47 0x004 +#define MX27_PAD_USBOTG_DATA5__GPIO3_7 0x47 0x036 +#define MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x48 0x004 +#define MX27_PAD_USBOTG_DATA6__GPIO3_8 0x48 0x036 +#define MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x49 0x004 +#define MX27_PAD_USBOTG_DATA0__GPIO3_9 0x49 0x036 +#define MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x4a 0x004 +#define MX27_PAD_USBOTG_DATA2__GPIO3_10 0x4a 0x036 +#define MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x4b 0x004 +#define MX27_PAD_USBOTG_DATA1__GPIO3_11 0x4b 0x036 +#define MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x4c 0x004 +#define MX27_PAD_USBOTG_DATA4__GPIO3_12 0x4c 0x036 +#define MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x4d 0x004 +#define MX27_PAD_USBOTG_DATA3__GPIO3_13 0x4d 0x036 +#define MX27_PAD_TOUT__TOUT 0x4e 0x004 +#define MX27_PAD_TOUT__GPIO3_14 0x4e 0x036 +#define MX27_PAD_TIN__TIN 0x4f 0x000 +#define MX27_PAD_TIN__GPIO3_15 0x4f 0x036 +#define MX27_PAD_SSI4_FS__SSI4_FS 0x50 0x004 +#define MX27_PAD_SSI4_FS__GPIO3_16 0x50 0x036 +#define MX27_PAD_SSI4_RXDAT__SSI4_RXDAT 0x51 0x004 +#define MX27_PAD_SSI4_RXDAT__GPIO3_17 0x51 0x036 +#define MX27_PAD_SSI4_TXDAT__SSI4_TXDAT 0x52 0x004 +#define MX27_PAD_SSI4_TXDAT__GPIO3_18 0x52 0x036 +#define MX27_PAD_SSI4_CLK__SSI4_CLK 0x53 0x004 +#define MX27_PAD_SSI4_CLK__GPIO3_19 0x53 0x036 +#define MX27_PAD_SSI1_FS__SSI1_FS 0x54 0x004 +#define MX27_PAD_SSI1_FS__GPIO3_20 0x54 0x036 +#define MX27_PAD_SSI1_RXDAT__SSI1_RXDAT 0x55 0x004 +#define MX27_PAD_SSI1_RXDAT__GPIO3_21 0x55 0x036 +#define MX27_PAD_SSI1_TXDAT__SSI1_TXDAT 0x56 0x004 +#define MX27_PAD_SSI1_TXDAT__GPIO3_22 0x56 0x036 +#define MX27_PAD_SSI1_CLK__SSI1_CLK 0x57 0x004 +#define MX27_PAD_SSI1_CLK__GPIO3_23 0x57 0x036 +#define MX27_PAD_SSI2_FS__SSI2_FS 0x58 0x004 +#define MX27_PAD_SSI2_FS__GPT5_TOUT 0x58 0x005 +#define MX27_PAD_SSI2_FS__GPIO3_24 0x58 0x036 +#define MX27_PAD_SSI2_RXDAT__SSI2_RXDAT 0x59 0x004 +#define MX27_PAD_SSI2_RXDAT__GPTS_TIN 0x59 0x001 +#define MX27_PAD_SSI2_RXDAT__GPIO3_25 0x59 0x036 +#define MX27_PAD_SSI2_TXDAT__SSI2_TXDAT 0x5a 0x004 +#define MX27_PAD_SSI2_TXDAT__GPT4_TOUT 0x5a 0x005 +#define MX27_PAD_SSI2_TXDAT__GPIO3_26 0x5a 0x036 +#define MX27_PAD_SSI2_CLK__SSI2_CLK 0x5b 0x004 +#define MX27_PAD_SSI2_CLK__GPT4_TIN 0x5b 0x001 +#define MX27_PAD_SSI2_CLK__GPIO3_27 0x5b 0x036 +#define MX27_PAD_SSI3_FS__SSI3_FS 0x5c 0x004 +#define MX27_PAD_SSI3_FS__SLCDC2_D0 0x5c 0x001 +#define MX27_PAD_SSI3_FS__GPIO3_28 0x5c 0x036 +#define MX27_PAD_SSI3_RXDAT__SSI3_RXDAT 0x5d 0x004 +#define MX27_PAD_SSI3_RXDAT__SLCDC2_RS 0x5d 0x001 +#define MX27_PAD_SSI3_RXDAT__GPIO3_29 0x5d 0x036 +#define MX27_PAD_SSI3_TXDAT__SSI3_TXDAT 0x5e 0x004 +#define MX27_PAD_SSI3_TXDAT__SLCDC2_CS 0x5e 0x001 +#define MX27_PAD_SSI3_TXDAT__GPIO3_30 0x5e 0x036 +#define MX27_PAD_SSI3_CLK__SSI3_CLK 0x5f 0x004 +#define MX27_PAD_SSI3_CLK__SLCDC2_CLK 0x5f 0x001 +#define MX27_PAD_SSI3_CLK__GPIO3_31 0x5f 0x036 +#define MX27_PAD_SD3_CMD__SD3_CMD 0x60 0x004 +#define MX27_PAD_SD3_CMD__FEC_TXD0 0x60 0x006 +#define MX27_PAD_SD3_CMD__GPIO4_0 0x60 0x036 +#define MX27_PAD_SD3_CLK__SD3_CLK 0x61 0x004 +#define MX27_PAD_SD3_CLK__ETMTRACEPKT15 0x61 0x005 +#define MX27_PAD_SD3_CLK__FEC_TXD1 0x61 0x006 +#define MX27_PAD_SD3_CLK__GPIO4_1 0x61 0x036 +#define MX27_PAD_ATA_DATA0__ATA_DATA0 0x62 0x004 +#define MX27_PAD_ATA_DATA0__SD3_D0 0x62 0x005 +#define MX27_PAD_ATA_DATA0__FEC_TXD2 0x62 0x006 +#define MX27_PAD_ATA_DATA0__GPIO4_2 0x62 0x036 +#define MX27_PAD_ATA_DATA1__ATA_DATA1 0x63 0x004 +#define MX27_PAD_ATA_DATA1__SD3_D1 0x63 0x005 +#define MX27_PAD_ATA_DATA1__FEC_TXD3 0x63 0x006 +#define MX27_PAD_ATA_DATA1__GPIO4_3 0x63 0x036 +#define MX27_PAD_ATA_DATA2__ATA_DATA2 0x64 0x004 +#define MX27_PAD_ATA_DATA2__SD3_D2 0x64 0x005 +#define MX27_PAD_ATA_DATA2__FEC_RX_ER 0x64 0x002 +#define MX27_PAD_ATA_DATA2__GPIO4_4 0x64 0x036 +#define MX27_PAD_ATA_DATA3__ATA_DATA3 0x65 0x004 +#define MX27_PAD_ATA_DATA3__SD3_D3 0x65 0x005 +#define MX27_PAD_ATA_DATA3__FEC_RXD1 0x65 0x002 +#define MX27_PAD_ATA_DATA3__GPIO4_5 0x65 0x036 +#define MX27_PAD_ATA_DATA4__ATA_DATA4 0x66 0x004 +#define MX27_PAD_ATA_DATA4__ETMTRACEPKT14 0x66 0x005 +#define MX27_PAD_ATA_DATA4__FEC_RXD2 0x66 0x002 +#define MX27_PAD_ATA_DATA4__GPIO4_6 0x66 0x036 +#define MX27_PAD_ATA_DATA5__ATA_DATA5 0x67 0x004 +#define MX27_PAD_ATA_DATA5__ETMTRACEPKT13 0x67 0x005 +#define MX27_PAD_ATA_DATA5__FEC_RXD3 0x67 0x002 +#define MX27_PAD_ATA_DATA5__GPIO4_7 0x67 0x036 +#define MX27_PAD_ATA_DATA6__ATA_DATA6 0x68 0x004 +#define MX27_PAD_ATA_DATA6__FEC_MDIO 0x68 0x005 +#define MX27_PAD_ATA_DATA6__GPIO4_8 0x68 0x036 +#define MX27_PAD_ATA_DATA7__ATA_DATA7 0x69 0x004 +#define MX27_PAD_ATA_DATA7__ETMTRACEPKT12 0x69 0x005 +#define MX27_PAD_ATA_DATA7__FEC_MDC 0x69 0x006 +#define MX27_PAD_ATA_DATA7__GPIO4_9 0x69 0x036 +#define MX27_PAD_ATA_DATA8__ATA_DATA8 0x6a 0x004 +#define MX27_PAD_ATA_DATA8__ETMTRACEPKT11 0x6a 0x005 +#define MX27_PAD_ATA_DATA8__FEC_CRS 0x6a 0x002 +#define MX27_PAD_ATA_DATA8__GPIO4_10 0x6a 0x036 +#define MX27_PAD_ATA_DATA9__ATA_DATA9 0x6b 0x004 +#define MX27_PAD_ATA_DATA9__ETMTRACEPKT10 0x6b 0x005 +#define MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x6b 0x002 +#define MX27_PAD_ATA_DATA9__GPIO4_11 0x6b 0x036 +#define MX27_PAD_ATA_DATA10__ATA_DATA10 0x6c 0x004 +#define MX27_PAD_ATA_DATA10__ETMTRACEPKT9 0x6c 0x005 +#define MX27_PAD_ATA_DATA10__FEC_RXD0 0x6c 0x002 +#define MX27_PAD_ATA_DATA10__GPIO4_12 0x6c 0x036 +#define MX27_PAD_ATA_DATA11__ATA_DATA11 0x6d 0x004 +#define MX27_PAD_ATA_DATA11__ETMTRACEPKT8 0x6d 0x005 +#define MX27_PAD_ATA_DATA11__FEC_RX_DV 0x6d 0x002 +#define MX27_PAD_ATA_DATA11__GPIO4_13 0x6d 0x036 +#define MX27_PAD_ATA_DATA12__ATA_DATA12 0x6e 0x004 +#define MX27_PAD_ATA_DATA12__ETMTRACEPKT7 0x6e 0x005 +#define MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x6e 0x002 +#define MX27_PAD_ATA_DATA12__GPIO4_14 0x6e 0x036 +#define MX27_PAD_ATA_DATA13__ATA_DATA13 0x6f 0x004 +#define MX27_PAD_ATA_DATA13__ETMTRACEPKT6 0x6f 0x005 +#define MX27_PAD_ATA_DATA13__FEC_COL 0x6f 0x002 +#define MX27_PAD_ATA_DATA13__GPIO4_15 0x6f 0x036 +#define MX27_PAD_ATA_DATA14__ATA_DATA14 0x70 0x004 +#define MX27_PAD_ATA_DATA14__ETMTRACEPKT5 0x70 0x005 +#define MX27_PAD_ATA_DATA14__FEC_TX_ER 0x70 0x006 +#define MX27_PAD_ATA_DATA14__GPIO4_16 0x70 0x036 +#define MX27_PAD_I2C_DATA__I2C_DATA 0x71 0x004 +#define MX27_PAD_I2C_DATA__GPIO4_17 0x71 0x036 +#define MX27_PAD_I2C_CLK__I2C_CLK 0x72 0x004 +#define MX27_PAD_I2C_CLK__GPIO4_18 0x72 0x036 +#define MX27_PAD_CSPI2_SS2__CSPI2_SS2 0x73 0x004 +#define MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x73 0x005 +#define MX27_PAD_CSPI2_SS2__GPIO4_19 0x73 0x036 +#define MX27_PAD_CSPI2_SS1__CSPI2_SS1 0x74 0x004 +#define MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x74 0x005 +#define MX27_PAD_CSPI2_SS1__GPIO4_20 0x74 0x036 +#define MX27_PAD_CSPI2_SS0__CSPI2_SS0 0x75 0x004 +#define MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x75 0x005 +#define MX27_PAD_CSPI2_SS0__GPIO4_21 0x75 0x036 +#define MX27_PAD_CSPI2_SCLK__CSPI2_SCLK 0x76 0x004 +#define MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x76 0x005 +#define MX27_PAD_CSPI2_SCLK__GPIO4_22 0x76 0x036 +#define MX27_PAD_CSPI2_MISO__CSPI2_MISO 0x77 0x004 +#define MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x77 0x005 +#define MX27_PAD_CSPI2_MISO__GPIO4_23 0x77 0x036 +#define MX27_PAD_CSPI2_MOSI__CSPI2_MOSI 0x78 0x004 +#define MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x78 0x005 +#define MX27_PAD_CSPI2_MOSI__GPIO4_24 0x78 0x036 +#define MX27_PAD_CSPI1_RDY__CSPI1_RDY 0x79 0x000 +#define MX27_PAD_CSPI1_RDY__GPIO4_25 0x79 0x036 +#define MX27_PAD_CSPI1_SS2__CSPI1_SS2 0x7a 0x004 +#define MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x7a 0x005 +#define MX27_PAD_CSPI1_SS2__GPIO4_26 0x7a 0x036 +#define MX27_PAD_CSPI1_SS1__CSPI1_SS1 0x7b 0x004 +#define MX27_PAD_CSPI1_SS1__GPIO4_27 0x7b 0x036 +#define MX27_PAD_CSPI1_SS0__CSPI1_SS0 0x7c 0x004 +#define MX27_PAD_CSPI1_SS0__GPIO4_28 0x7c 0x036 +#define MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x7d 0x004 +#define MX27_PAD_CSPI1_SCLK__GPIO4_29 0x7d 0x036 +#define MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x7e 0x004 +#define MX27_PAD_CSPI1_MISO__GPIO4_30 0x7e 0x036 +#define MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x7f 0x004 +#define MX27_PAD_CSPI1_MOSI__GPIO4_31 0x7f 0x036 +#define MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x80 0x000 +#define MX27_PAD_USBOTG_NXT__KP_COL6A 0x80 0x005 +#define MX27_PAD_USBOTG_NXT__GPIO5_0 0x80 0x036 +#define MX27_PAD_USBOTG_STP__USBOTG_STP 0x81 0x004 +#define MX27_PAD_USBOTG_STP__KP_ROW6A 0x81 0x005 +#define MX27_PAD_USBOTG_STP__GPIO5_1 0x81 0x036 +#define MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x82 0x000 +#define MX27_PAD_USBOTG_DIR__KP_ROW7A 0x82 0x005 +#define MX27_PAD_USBOTG_DIR__GPIO5_2 0x82 0x036 +#define MX27_PAD_UART2_CTS__UART2_CTS 0x83 0x004 +#define MX27_PAD_UART2_CTS__KP_COL7 0x83 0x005 +#define MX27_PAD_UART2_CTS__GPIO5_3 0x83 0x036 +#define MX27_PAD_UART2_RTS__UART2_RTS 0x84 0x000 +#define MX27_PAD_UART2_RTS__KP_ROW7 0x84 0x005 +#define MX27_PAD_UART2_RTS__GPIO5_4 0x84 0x036 +#define MX27_PAD_PWMO__PWMO 0x85 0x004 +#define MX27_PAD_PWMO__GPIO5_5 0x85 0x036 +#define MX27_PAD_UART2_TXD__UART2_TXD 0x86 0x004 +#define MX27_PAD_UART2_TXD__KP_COL6 0x86 0x005 +#define MX27_PAD_UART2_TXD__GPIO5_6 0x86 0x036 +#define MX27_PAD_UART2_RXD__UART2_RXD 0x87 0x000 +#define MX27_PAD_UART2_RXD__KP_ROW6 0x87 0x005 +#define MX27_PAD_UART2_RXD__GPIO5_7 0x87 0x036 +#define MX27_PAD_UART3_TXD__UART3_TXD 0x88 0x004 +#define MX27_PAD_UART3_TXD__GPIO5_8 0x88 0x036 +#define MX27_PAD_UART3_RXD__UART3_RXD 0x89 0x000 +#define MX27_PAD_UART3_RXD__GPIO5_9 0x89 0x036 +#define MX27_PAD_UART3_CTS__UART3_CTS 0x8a 0x004 +#define MX27_PAD_UART3_CTS__GPIO5_10 0x8a 0x036 +#define MX27_PAD_UART3_RTS__UART3_RTS 0x8b 0x000 +#define MX27_PAD_UART3_RTS__GPIO5_11 0x8b 0x036 +#define MX27_PAD_UART1_TXD__UART1_TXD 0x8c 0x004 +#define MX27_PAD_UART1_TXD__GPIO5_12 0x8c 0x036 +#define MX27_PAD_UART1_RXD__UART1_RXD 0x8d 0x000 +#define MX27_PAD_UART1_RXD__GPIO5_13 0x8d 0x036 +#define MX27_PAD_UART1_CTS__UART1_CTS 0x8e 0x004 +#define MX27_PAD_UART1_CTS__GPIO5_14 0x8e 0x036 +#define MX27_PAD_UART1_RTS__UART1_RTS 0x8f 0x000 +#define MX27_PAD_UART1_RTS__GPIO5_15 0x8f 0x036 +#define MX27_PAD_RTCK__RTCK 0x90 0x004 +#define MX27_PAD_RTCK__OWIRE 0x90 0x005 +#define MX27_PAD_RTCK__GPIO5_16 0x90 0x036 +#define MX27_PAD_RESET_OUT_B__RESET_OUT_B 0x91 0x004 +#define MX27_PAD_RESET_OUT_B__GPIO5_17 0x91 0x036 +#define MX27_PAD_SD1_D0__SD1_D0 0x92 0x004 +#define MX27_PAD_SD1_D0__CSPI3_MISO 0x92 0x001 +#define MX27_PAD_SD1_D0__GPIO5_18 0x92 0x036 +#define MX27_PAD_SD1_D1__SD1_D1 0x93 0x004 +#define MX27_PAD_SD1_D1__GPIO5_19 0x93 0x036 +#define MX27_PAD_SD1_D2__SD1_D2 0x94 0x004 +#define MX27_PAD_SD1_D2__GPIO5_20 0x94 0x036 +#define MX27_PAD_SD1_D3__SD1_D3 0x95 0x004 +#define MX27_PAD_SD1_D3__CSPI3_SS 0x95 0x005 +#define MX27_PAD_SD1_D3__GPIO5_21 0x95 0x036 +#define MX27_PAD_SD1_CMD__SD1_CMD 0x96 0x004 +#define MX27_PAD_SD1_CMD__CSPI3_MOSI 0x96 0x005 +#define MX27_PAD_SD1_CMD__GPIO5_22 0x96 0x036 +#define MX27_PAD_SD1_CLK__SD1_CLK 0x97 0x004 +#define MX27_PAD_SD1_CLK__CSPI3_SCLK 0x97 0x005 +#define MX27_PAD_SD1_CLK__GPIO5_23 0x97 0x036 +#define MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x98 0x000 +#define MX27_PAD_USBOTG_CLK__GPIO5_24 0x98 0x036 +#define MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x99 0x004 +#define MX27_PAD_USBOTG_DATA7__GPIO5_25 0x99 0x036 +#define MX27_PAD_UNUSED9__UNUSED9 0x9a 0x004 +#define MX27_PAD_UNUSED9__GPIO5_26 0x9a 0x036 +#define MX27_PAD_UNUSED10__UNUSED10 0x9b 0x004 +#define MX27_PAD_UNUSED10__GPIO5_27 0x9b 0x036 +#define MX27_PAD_UNUSED11__UNUSED11 0x9c 0x004 +#define MX27_PAD_UNUSED11__GPIO5_28 0x9c 0x036 +#define MX27_PAD_UNUSED12__UNUSED12 0x9d 0x004 +#define MX27_PAD_UNUSED12__GPIO5_29 0x9d 0x036 +#define MX27_PAD_UNUSED13__UNUSED13 0x9e 0x004 +#define MX27_PAD_UNUSED13__GPIO5_30 0x9e 0x036 +#define MX27_PAD_UNUSED14__UNUSED14 0x9f 0x004 +#define MX27_PAD_UNUSED14__GPIO5_31 0x9f 0x036 +#define MX27_PAD_NFRB__NFRB 0xa0 0x000 +#define MX27_PAD_NFRB__ETMTRACEPKT3 0xa0 0x005 +#define MX27_PAD_NFRB__GPIO6_0 0xa0 0x036 +#define MX27_PAD_NFCLE__NFCLE 0xa1 0x004 +#define MX27_PAD_NFCLE__ETMTRACEPKT0 0xa1 0x005 +#define MX27_PAD_NFCLE__GPIO6_1 0xa1 0x036 +#define MX27_PAD_NFWP_B__NFWP_B 0xa2 0x004 +#define MX27_PAD_NFWP_B__ETMTRACEPKT1 0xa2 0x005 +#define MX27_PAD_NFWP_B__GPIO6_2 0xa2 0x036 +#define MX27_PAD_NFCE_B__NFCE_B 0xa3 0x004 +#define MX27_PAD_NFCE_B__ETMTRACEPKT2 0xa3 0x005 +#define MX27_PAD_NFCE_B__GPIO6_3 0xa3 0x036 +#define MX27_PAD_NFALE__NFALE 0xa4 0x004 +#define MX27_PAD_NFALE__ETMPIPESTAT0 0xa4 0x005 +#define MX27_PAD_NFALE__GPIO6_4 0xa4 0x036 +#define MX27_PAD_NFRE_B__NFRE_B 0xa5 0x004 +#define MX27_PAD_NFRE_B__ETMPIPESTAT1 0xa5 0x005 +#define MX27_PAD_NFRE_B__GPIO6_5 0xa5 0x036 +#define MX27_PAD_NFWE_B__NFWE_B 0xa6 0x004 +#define MX27_PAD_NFWE_B__ETMPIPESTAT2 0xa6 0x005 +#define MX27_PAD_NFWE_B__GPIO6_6 0xa6 0x036 +#define MX27_PAD_PC_POE__PC_POE 0xa7 0x004 +#define MX27_PAD_PC_POE__ATA_BUFFER_EN 0xa7 0x005 +#define MX27_PAD_PC_POE__GPIO6_7 0xa7 0x036 +#define MX27_PAD_PC_RW_B__PC_RW_B 0xa8 0x004 +#define MX27_PAD_PC_RW_B__ATA_IORDY 0xa8 0x001 +#define MX27_PAD_PC_RW_B__GPIO6_8 0xa8 0x036 +#define MX27_PAD_IOIS16__IOIS16 0xa9 0x000 +#define MX27_PAD_IOIS16__ATA_INTRQ 0xa9 0x001 +#define MX27_PAD_IOIS16__GPIO6_9 0xa9 0x036 +#define MX27_PAD_PC_RST__PC_RST 0xaa 0x004 +#define MX27_PAD_PC_RST__ATA_RESET_B 0xaa 0x005 +#define MX27_PAD_PC_RST__GPIO6_10 0xaa 0x036 +#define MX27_PAD_PC_BVD2__PC_BVD2 0xab 0x000 +#define MX27_PAD_PC_BVD2__ATA_DMACK 0xab 0x005 +#define MX27_PAD_PC_BVD2__GPIO6_11 0xab 0x036 +#define MX27_PAD_PC_BVD1__PC_BVD1 0xac 0x000 +#define MX27_PAD_PC_BVD1__ATA_DMARQ 0xac 0x001 +#define MX27_PAD_PC_BVD1__GPIO6_12 0xac 0x036 +#define MX27_PAD_PC_VS2__PC_VS2 0xad 0x000 +#define MX27_PAD_PC_VS2__ATA_DA0 0xad 0x005 +#define MX27_PAD_PC_VS2__GPIO6_13 0xad 0x036 +#define MX27_PAD_PC_VS1__PC_VS1 0xae 0x000 +#define MX27_PAD_PC_VS1__ATA_DA1 0xae 0x005 +#define MX27_PAD_PC_VS1__GPIO6_14 0xae 0x036 +#define MX27_PAD_CLKO__CLKO 0xaf 0x004 +#define MX27_PAD_CLKO__GPIO6_15 0xaf 0x036 +#define MX27_PAD_PC_PWRON__PC_PWRON 0xb0 0x000 +#define MX27_PAD_PC_PWRON__ATA_DA2 0xb0 0x005 +#define MX27_PAD_PC_PWRON__GPIO6_16 0xb0 0x036 +#define MX27_PAD_PC_READY__PC_READY 0xb1 0x000 +#define MX27_PAD_PC_READY__ATA_CS0 0xb1 0x005 +#define MX27_PAD_PC_READY__GPIO6_17 0xb1 0x036 +#define MX27_PAD_PC_WAIT_B__PC_WAIT_B 0xb2 0x000 +#define MX27_PAD_PC_WAIT_B__ATA_CS1 0xb2 0x005 +#define MX27_PAD_PC_WAIT_B__GPIO6_18 0xb2 0x036 +#define MX27_PAD_PC_CD2_B__PC_CD2_B 0xb3 0x000 +#define MX27_PAD_PC_CD2_B__ATA_DIOW 0xb3 0x005 +#define MX27_PAD_PC_CD2_B__GPIO6_19 0xb3 0x036 +#define MX27_PAD_PC_CD1_B__PC_CD1_B 0xb4 0x000 +#define MX27_PAD_PC_CD1_B__ATA_DIOR 0xb4 0x005 +#define MX27_PAD_PC_CD1_B__GPIO6_20 0xb4 0x036 +#define MX27_PAD_CS4_B__CS4_B 0xb5 0x004 +#define MX27_PAD_CS4_B__ETMTRACESYNC 0xb5 0x005 +#define MX27_PAD_CS4_B__GPIO6_21 0xb5 0x036 +#define MX27_PAD_CS5_B__CS5_B 0xb6 0x004 +#define MX27_PAD_CS5_B__ETMTRACECLK 0xb6 0x005 +#define MX27_PAD_CS5_B__GPIO6_22 0xb6 0x036 +#define MX27_PAD_ATA_DATA15__ATA_DATA15 0xb7 0x004 +#define MX27_PAD_ATA_DATA15__ETMTRACEPKT4 0xb7 0x005 +#define MX27_PAD_ATA_DATA15__FEC_TX_EN 0xb7 0x006 +#define MX27_PAD_ATA_DATA15__GPIO6_23 0xb7 0x036 +#define MX27_PAD_UNUSED15__UNUSED15 0xb8 0x004 +#define MX27_PAD_UNUSED15__GPIO6_24 0xb8 0x036 +#define MX27_PAD_UNUSED16__UNUSED16 0xb9 0x004 +#define MX27_PAD_UNUSED16__GPIO6_25 0xb9 0x036 +#define MX27_PAD_UNUSED17__UNUSED17 0xba 0x004 +#define MX27_PAD_UNUSED17__GPIO6_26 0xba 0x036 +#define MX27_PAD_UNUSED18__UNUSED18 0xbb 0x004 +#define MX27_PAD_UNUSED18__GPIO6_27 0xbb 0x036 +#define MX27_PAD_UNUSED19__UNUSED19 0xbc 0x004 +#define MX27_PAD_UNUSED19__GPIO6_28 0xbc 0x036 +#define MX27_PAD_UNUSED20__UNUSED20 0xbd 0x004 +#define MX27_PAD_UNUSED20__GPIO6_29 0xbd 0x036 +#define MX27_PAD_UNUSED21__UNUSED21 0xbe 0x004 +#define MX27_PAD_UNUSED21__GPIO6_30 0xbe 0x036 +#define MX27_PAD_UNUSED22__UNUSED22 0xbf 0x004 +#define MX27_PAD_UNUSED22__GPIO6_31 0xbf 0x036 + +#endif /* __DTS_IMX27_PINFUNC_H */ -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 4/7] ARM: dts: imx27 pinctrl 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann ` (2 preceding siblings ...) 2013-10-24 7:53 ` [PATCH v4 3/7] ARM: dts: imx27 pin functions Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 5/7] ARM: dts: imx27 phyCARD-S pinctrl Markus Pargmann ` (3 subsequent siblings) 7 siblings, 0 replies; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel Pinctrl driver node and pin group definitions for other driver nodes. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27.dtsi | 102 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 102 insertions(+) diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index b7a1c6d..641a63d 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include "imx27-pinfunc.h" / { aliases { @@ -235,6 +236,12 @@ status = "disabled"; }; + iomuxc: iomuxc at 10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + + }; + gpio1: gpio at 10015000 { compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; reg = <0x10015000 0x100>; @@ -467,3 +474,98 @@ }; }; }; + +&iomuxc { + fec { + pinctrl_fec1_1: fec1-1 { + fsl,pins = < + MX27_PAD_SD3_CMD__FEC_TXD0 0x0 + MX27_PAD_SD3_CLK__FEC_TXD1 0x0 + MX27_PAD_ATA_DATA0__FEC_TXD2 0x0 + MX27_PAD_ATA_DATA1__FEC_TXD3 0x0 + MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0 + MX27_PAD_ATA_DATA3__FEC_RXD1 0x0 + MX27_PAD_ATA_DATA4__FEC_RXD2 0x0 + MX27_PAD_ATA_DATA5__FEC_RXD3 0x0 + MX27_PAD_ATA_DATA6__FEC_MDIO 0x0 + MX27_PAD_ATA_DATA7__FEC_MDC 0x0 + MX27_PAD_ATA_DATA8__FEC_CRS 0x0 + MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0 + MX27_PAD_ATA_DATA10__FEC_RXD0 0x0 + MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0 + MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0 + MX27_PAD_ATA_DATA13__FEC_COL 0x0 + MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0 + MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0 + >; + }; + }; + + i2c { + pinctrl_i2c1_1: i2c1-1 { + fsl,pins = < + MX27_PAD_I2C_DATA__I2C_DATA 0x0 + MX27_PAD_I2C_CLK__I2C_CLK 0x0 + >; + }; + + pinctrl_i2c2_1: i2c2-1 { + fsl,pins = < + MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 + MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 + >; + }; + }; + + owire { + pinctrl_owire1_1: owire1-1 { + fsl,pins = < + MX27_PAD_RTCK__OWIRE 0x0 + >; + }; + }; + + uart { + pinctrl_uart1_1: uart1-1 { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + >; + }; + + pinctrl_uart1_rtscts_1: uart1-rtscts-1 { + fsl,pins = < + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + pinctrl_uart2_1: uart2-1 { + fsl,pins = < + MX27_PAD_UART2_TXD__UART2_TXD 0x0 + MX27_PAD_UART2_RXD__UART2_RXD 0x0 + >; + }; + + pinctrl_uart2_rtscts_1: uart2-rtscts-1 { + fsl,pins = < + MX27_PAD_UART2_CTS__UART2_CTS 0x0 + MX27_PAD_UART2_RTS__UART2_RTS 0x0 + >; + }; + + pinctrl_uart3_1: uart3-1 { + fsl,pins = < + MX27_PAD_UART3_TXD__UART3_TXD 0x0 + MX27_PAD_UART3_RXD__UART3_RXD 0x0 + >; + }; + + pinctrl_uart3_rtscts_1: uart3-rtscts-1 { + fsl,pins = < + MX27_PAD_UART3_CTS__UART3_CTS 0x0 + MX27_PAD_UART3_RTS__UART3_RTS 0x0 + >; + }; + }; +}; -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 5/7] ARM: dts: imx27 phyCARD-S pinctrl 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann ` (3 preceding siblings ...) 2013-10-24 7:53 ` [PATCH v4 4/7] ARM: dts: imx27 pinctrl Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl Markus Pargmann ` (2 subsequent siblings) 7 siblings, 0 replies; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel Enable pinctrl for phyCARD-S devices. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts | 10 ++++++++++ arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts | 4 ++++ 2 files changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts index 5a31c77..505e688 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts @@ -54,6 +54,8 @@ }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1>; status = "okay"; rtc at 51 { @@ -69,6 +71,8 @@ }; &owire { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_owire1_1>; status = "okay"; }; @@ -79,15 +83,21 @@ &uart1 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; status = "okay"; }; &uart2 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_1 &pinctrl_uart2_rtscts_1>; status = "okay"; }; &uart3 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3_1 &pinctrl_uart3_rtscts_1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts index c8d57d1..0cee738 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts @@ -30,10 +30,14 @@ }; &fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1_1>; status = "okay"; }; &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_1>; status = "okay"; at24 at 52 { -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann ` (4 preceding siblings ...) 2013-10-24 7:53 ` [PATCH v4 5/7] ARM: dts: imx27 phyCARD-S pinctrl Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 8:30 ` Alexander Shiyan 2013-10-24 7:53 ` [PATCH v4 7/7] ARM: imx27: enable pinctrl Markus Pargmann 2013-10-24 8:35 ` [PATCH v4 0/7] ARM: imx27 pinctrl Shawn Guo 7 siblings, 1 reply; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel Enable pinctrl for phycore devices. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 2 ++ arch/arm/boot/dts/imx27-phytec-phycore-som.dts | 6 ++++++ 2 files changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts index 0fc6551..9bedd2f 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts @@ -33,6 +33,8 @@ &uart2 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_1 &pinctrl_uart2_rtscts_1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts index 4ec402c..3dbdb5e 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts @@ -135,11 +135,15 @@ &fec { phy-reset-gpios = <&gpio3 30 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1_1>; status = "okay"; }; &i2c2 { clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_1>; status = "okay"; at24 at 52 { @@ -166,6 +170,8 @@ }; &uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; status = "okay"; }; -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl 2013-10-24 7:53 ` [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl Markus Pargmann @ 2013-10-24 8:30 ` Alexander Shiyan 2013-10-24 9:27 ` Markus Pargmann 0 siblings, 1 reply; 12+ messages in thread From: Alexander Shiyan @ 2013-10-24 8:30 UTC (permalink / raw) To: linux-arm-kernel > Enable pinctrl for phycore devices. > > Signed-off-by: Markus Pargmann <mpa@pengutronix.de> > Acked-by: Sascha Hauer <s.hauer@pengutronix.de> ... > diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts > index 4ec402c..3dbdb5e 100644 > --- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts > +++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts ... > &uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; > status = "okay"; > }; No. Please put RTS & CTS pins into RDK. There are no hardware dependencies for SOM. --- ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl 2013-10-24 8:30 ` Alexander Shiyan @ 2013-10-24 9:27 ` Markus Pargmann 0 siblings, 0 replies; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 9:27 UTC (permalink / raw) To: linux-arm-kernel On Thu, Oct 24, 2013 at 12:30:24PM +0400, Alexander Shiyan wrote: > > Enable pinctrl for phycore devices. > > > > Signed-off-by: Markus Pargmann <mpa@pengutronix.de> > > Acked-by: Sascha Hauer <s.hauer@pengutronix.de> > ... > > diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts > > index 4ec402c..3dbdb5e 100644 > > --- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts > > +++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts > ... > > &uart1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; > > status = "okay"; > > }; > > No. Please put RTS & CTS pins into RDK. There are no hardware dependencies for SOM. Okay, I will move both uarts into rdk. Thanks, Markus -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v4 7/7] ARM: imx27: enable pinctrl 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann ` (5 preceding siblings ...) 2013-10-24 7:53 ` [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl Markus Pargmann @ 2013-10-24 7:53 ` Markus Pargmann 2013-10-24 8:35 ` [PATCH v4 0/7] ARM: imx27 pinctrl Shawn Guo 7 siblings, 0 replies; 12+ messages in thread From: Markus Pargmann @ 2013-10-24 7:53 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> --- arch/arm/mach-imx/Kconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 29a8af6..58726d5 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -121,6 +121,8 @@ config SOC_IMX27 select IMX_HAVE_IOMUX_V1 select MACH_MX27 select MXC_AVIC + select PINCTRL + select PINCTRL_IMX27 config SOC_IMX31 bool -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v4 0/7] ARM: imx27 pinctrl 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann ` (6 preceding siblings ...) 2013-10-24 7:53 ` [PATCH v4 7/7] ARM: imx27: enable pinctrl Markus Pargmann @ 2013-10-24 8:35 ` Shawn Guo 7 siblings, 0 replies; 12+ messages in thread From: Shawn Guo @ 2013-10-24 8:35 UTC (permalink / raw) To: linux-arm-kernel Linus, On Thu, Oct 24, 2013 at 09:53:46AM +0200, Markus Pargmann wrote: > Markus Pargmann (7): > pinctrl: imx1 core driver > pinctrl: imx27: imx27 pincontrol driver Is it still possible to queue these two patches for 3.13 merge window, so that we get imx27 device tree machine work on 3.13-rc? Shawn > ARM: dts: imx27 pin functions > ARM: dts: imx27 pinctrl > ARM: dts: imx27 phyCARD-S pinctrl > ARM: dts: imx27 phycore pinctrl > ARM: imx27: enable pinctrl > > .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 ++ > arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts | 10 + > arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts | 4 + > arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 2 + > arch/arm/boot/dts/imx27-phytec-phycore-som.dts | 6 + > arch/arm/boot/dts/imx27-pinfunc.h | 524 +++++++++++++++++ > arch/arm/boot/dts/imx27.dtsi | 102 ++++ > arch/arm/mach-imx/Kconfig | 2 + > drivers/pinctrl/Kconfig | 13 + > drivers/pinctrl/Makefile | 2 + > drivers/pinctrl/pinctrl-imx1-core.c | 653 +++++++++++++++++++++ > drivers/pinctrl/pinctrl-imx1.h | 73 +++ > drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++ > 13 files changed, 1918 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > create mode 100644 arch/arm/boot/dts/imx27-pinfunc.h > create mode 100644 drivers/pinctrl/pinctrl-imx1-core.c > create mode 100644 drivers/pinctrl/pinctrl-imx1.h > create mode 100644 drivers/pinctrl/pinctrl-imx27.c > > -- > 1.8.4.rc3 > ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2013-10-24 10:19 UTC | newest] Thread overview: 12+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-10-24 7:53 [PATCH v4 0/7] ARM: imx27 pinctrl Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 1/7] pinctrl: imx1 core driver Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 2/7] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann 2013-10-24 10:19 ` Grant Likely 2013-10-24 7:53 ` [PATCH v4 3/7] ARM: dts: imx27 pin functions Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 4/7] ARM: dts: imx27 pinctrl Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 5/7] ARM: dts: imx27 phyCARD-S pinctrl Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 6/7] ARM: dts: imx27 phycore pinctrl Markus Pargmann 2013-10-24 8:30 ` Alexander Shiyan 2013-10-24 9:27 ` Markus Pargmann 2013-10-24 7:53 ` [PATCH v4 7/7] ARM: imx27: enable pinctrl Markus Pargmann 2013-10-24 8:35 ` [PATCH v4 0/7] ARM: imx27 pinctrl Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).