[PATCH v2] add support for i.MX6 based cpu modul dmo edmqmx6

[PATCH v2] add support for i.MX6 based cpu modul dmo edmqmx6

[Silvio F]

This patches adds support for the i.MX6 based cpu module edmqmx6 from Data
Modul.

v2:
    rebase on to commit db882158

[PATCH 1/2] DT: Add Data Modul vendor prefix

[Silvio F]

Signed-off-by: Silvio F <silvio.fricke@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 8319844..bd7dbd7 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -22,6 +22,7 @@ cortina	Cortina Systems, Inc.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 denx	Denx Software Engineering
+dmo	Data Modul AG
 emmicro	EM Microelectronic
 epson	Seiko Epson Corp.
 est	ESTeem Wireless Modems
-- 
1.8.4.2

[PATCH 2/2] ARM: dts: imx6: Add support for imx6q dmo edmqmx6

[Silvio F]

Signed-off-by: Silvio F <silvio.fricke@gmail.com>
---
 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts | 182 ++++++++++++++++++++++++++++++++
 2 files changed, 183 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5468d2d..3159ab6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6dl-wandboard.dtb \
 	imx6q-arm2.dtb \
 	imx6q-cm-fx6.dtb \
+	imx6q-dmo-edmqmx6.dtb \
 	imx6q-gw51xx.dtb \
 	imx6q-gw52xx.dtb \
 	imx6q-gw53xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
new file mode 100644
index 0000000..77b045a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
@@ -0,0 +1,182 @@
+/*
+ * Copyright 2013 Data Modul AG
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+/ {
+	model = "Data Modul eDM-QMX6 Board";
+	compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q";
+
+	aliases {
+		gpio7 = &stmpe_gpio_1;
+		gpio8 = &stmpe_gpio_2;
+	};
+
+	memory {
+		reg = <0x10000000 0x80000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usb_otg_vbus: usb_otg_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio7 12 0>;
+		};
+
+		reg_usb_host1: usb_host1_en {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_host1_en";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio3 31 0>;
+			enable-active-high;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 0>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2
+		     &pinctrl_stmpe_1
+		     &pinctrl_stmpe_2>;
+	status = "okay";
+
+	rtc: m41t62 at 68 {
+		compatible = "stm,m41t62";
+		reg = <0x68>;
+	};
+	stmpe1: stmpe1601 at 40 {
+		compatible = "st,stmpe1601";
+		reg = <0x40>;
+		interrupts = <30 0>;
+		interrupt-parent = <&gpio3>;
+
+		stmpe_gpio_1: stmpe_gpio {
+			compatible = "st,stmpe-gpio";
+		};
+	};
+
+	stmpe2: stmpe1601 at 44 {
+		compatible = "st,stmpe1601";
+		reg = <0x44>;
+		interrupts = <2 0>;
+		interrupt-parent = <&gpio5>;
+
+		stmpe_gpio_2: stmpe_gpio {
+			compatible = "st,stmpe-gpio";
+		};
+	};
+
+	temp1: ad7414 at 4c {
+		compatible = "ad,ad7414";
+		reg = <0x4c>;
+	};
+
+	temp2: ad7414 at 4d {
+		compatible = "ad,ad7414";
+		reg = <0x4d>;
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <MX6QDL_ENET_PINGRP1>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <MX6QDL_I2C2_PINGRP3>;
+	};
+
+	stmpe1 {
+		pinctrl_stmpe_1: stmpe1grp-1 {
+			fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>;
+		};
+	};
+
+	stmpe2 {
+		pinctrl_stmpe_2: stmpe2grp-1 {
+			fsl,pins = <MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000>;
+		};
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <MX6QDL_UART1_PINGRP2>;
+	};
+
+	pinctrl_uart2: uart1grp {
+		fsl,pins = <MX6QDL_UART2_PINGRP1>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <MX6QDL_USBOTG_PINGRP1>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <MX6QDL_USDHC3_PINGRP2>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_host1>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
-- 
1.8.4.2

[PATCH 2/2] ARM: dts: imx6: Add support for imx6q dmo edmqmx6

[Shawn Guo]

On Wed, Nov 06, 2013 at 10:04:42PM +0100, Silvio F wrote:
> Signed-off-by: Silvio F <silvio.fricke@gmail.com>
> ---
>  arch/arm/boot/dts/Makefile              |   1 +
>  arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts | 182 ++++++++++++++++++++++++++++++++
>  2 files changed, 183 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 5468d2d..3159ab6 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
>  	imx6dl-wandboard.dtb \
>  	imx6q-arm2.dtb \
>  	imx6q-cm-fx6.dtb \
> +	imx6q-dmo-edmqmx6.dtb \
>  	imx6q-gw51xx.dtb \
>  	imx6q-gw52xx.dtb \
>  	imx6q-gw53xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
> new file mode 100644
> index 0000000..77b045a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
> @@ -0,0 +1,182 @@
> +/*
> + * Copyright 2013 Data Modul AG
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +
> +/ {
> +	model = "Data Modul eDM-QMX6 Board";
> +	compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q";
> +
> +	aliases {
> +		gpio7 = &stmpe_gpio_1;
> +		gpio8 = &stmpe_gpio_2;
> +	};
> +
> +	memory {
> +		reg = <0x10000000 0x80000000>;
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +
> +		reg_3p3v: 3p3v {

Oh, we just started using generic name for fixed regulator nodes.  Can
you please have a look at the patch below and follow the naming schema
used there?

http://www.spinics.net/lists/arm-kernel/msg284474.html

> +			compatible = "regulator-fixed";
> +			regulator-name = "3P3V";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_usb_otg_vbus: usb_otg_vbus {
> +			compatible = "regulator-fixed";
> +			regulator-name = "usb_otg_vbus";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			gpio = <&gpio7 12 0>;
> +		};
> +
> +		reg_usb_host1: usb_host1_en {
> +			compatible = "regulator-fixed";
> +			regulator-name = "usb_host1_en";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio3 31 0>;
> +			enable-active-high;
> +		};
> +	};
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet>;
> +	phy-mode = "rgmii";
> +	phy-reset-gpios = <&gpio3 23 0>;
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2
> +		     &pinctrl_stmpe_1
> +		     &pinctrl_stmpe_2>;
> +	status = "okay";
> +
> +	rtc: m41t62 at 68 {
> +		compatible = "stm,m41t62";
> +		reg = <0x68>;
> +	};

We generally have a blank lines between nodes.  Also when nodes have
'@num' in their names, we would sort them in 'num'.

> +	stmpe1: stmpe1601 at 40 {
> +		compatible = "st,stmpe1601";
> +		reg = <0x40>;
> +		interrupts = <30 0>;
> +		interrupt-parent = <&gpio3>;
> +
> +		stmpe_gpio_1: stmpe_gpio {
> +			compatible = "st,stmpe-gpio";
> +		};
> +	};
> +
> +	stmpe2: stmpe1601 at 44 {
> +		compatible = "st,stmpe1601";
> +		reg = <0x44>;
> +		interrupts = <2 0>;
> +		interrupt-parent = <&gpio5>;
> +
> +		stmpe_gpio_2: stmpe_gpio {
> +			compatible = "st,stmpe-gpio";
> +		};
> +	};
> +
> +	temp1: ad7414 at 4c {
> +		compatible = "ad,ad7414";
> +		reg = <0x4c>;
> +	};
> +
> +	temp2: ad7414 at 4d {
> +		compatible = "ad,ad7414";
> +		reg = <0x4d>;
> +	};
> +};
> +
> +&iomuxc {
> +	pinctrl_enet: enetgrp {
> +		fsl,pins = <MX6QDL_ENET_PINGRP1>;
> +	};

Thanks for adopting the pingrp macros we just introduced.  But all
these pinctrl nodes should be in another container node.  Otherwise,
pinctrl driver will not be able to parse them.

> +
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <MX6QDL_I2C2_PINGRP3>;
> +	};
> +
> +	stmpe1 {

Right, just like this.  But I would suggest you have one container node
for all these pinctrl node.

> +		pinctrl_stmpe_1: stmpe1grp-1 {

s/stmpe1grp-1/stmpe1grp

> +			fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>;
> +		};
> +	};
> +
> +	stmpe2 {
> +		pinctrl_stmpe_2: stmpe2grp-1 {

Ditto

> +			fsl,pins = <MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000>;
> +		};
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <MX6QDL_UART1_PINGRP2>;
> +	};
> +
> +	pinctrl_uart2: uart1grp {

s/uart1grp/uart2grp

Shawn

> +		fsl,pins = <MX6QDL_UART2_PINGRP1>;
> +	};
> +
> +	pinctrl_usbotg: usbotggrp {
> +		fsl,pins = <MX6QDL_USBOTG_PINGRP1>;
> +	};
> +
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <MX6QDL_USDHC3_PINGRP2>;
> +	};
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	vbus-supply = <&reg_usb_host1>;
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&usbotg {
> +	vbus-supply = <&reg_usb_otg_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg>;
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&usdhc3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	vmmc-supply = <&reg_3p3v>;
> +	status = "okay";
> +};
> +
> -- 
> 1.8.4.2
> 

[PATCH v3] add support for i.MX6 based cpu modul dmo edmqmx6

[Silvio F.]

Hi,

I hope now is all correct?!

Cheers,
    Silvio

This patches adds support for the i.MX6 based cpu module edmqmx6 from Data
Modul.

v3:
    * rebase to commit deb07cd3
      git://git.linaro.org/people/shawnguo/linux-2.6.git
    * include suggestions from
      http://lists.infradead.org/pipermail/linux-arm-kernel/2013-November/209676.html
    * remove second stmpe because problems with two stmpes
      sysfs: cannot create duplicate filename
      '/bus/platform/devices/stmpe-gpio'

v2:
    * rebase to commit db882158
      git://git.linaro.org/people/shawnguo/linux-2.6.git

v1:
    * Add support

[PATCH 1/2] DT: Add Data Modul vendor prefix

[Silvio F.]

From: Silvio F <silvio.fricke@gmail.com>

Signed-off-by: Silvio F <silvio.fricke@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 8319844..bd7dbd7 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -22,6 +22,7 @@ cortina	Cortina Systems, Inc.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 denx	Denx Software Engineering
+dmo	Data Modul AG
 emmicro	EM Microelectronic
 epson	Seiko Epson Corp.
 est	ESTeem Wireless Modems
-- 
1.8.4.2

[PATCH 2/2] ARM: dts: imx6: Add support for imx6q dmo edmqmx6

[Silvio F.]

From: Silvio F <silvio.fricke@gmail.com>

Signed-off-by: Silvio F <silvio.fricke@gmail.com>
---
 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts | 179 ++++++++++++++++++++++++++++++++
 2 files changed, 180 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5468d2d..3159ab6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6dl-wandboard.dtb \
 	imx6q-arm2.dtb \
 	imx6q-cm-fx6.dtb \
+	imx6q-dmo-edmqmx6.dtb \
 	imx6q-gw51xx.dtb \
 	imx6q-gw52xx.dtb \
 	imx6q-gw53xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
new file mode 100644
index 0000000..cd64dfb
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
@@ -0,0 +1,179 @@
+/*
+ * Copyright 2013 Data Modul AG
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+/ {
+	model = "Data Modul eDM-QMX6 Board";
+	compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q";
+
+	aliases {
+		gpio7 = &stmpe_gpio;
+	};
+
+	memory {
+		reg = <0x10000000 0x80000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_3p3v: regulator at 0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usb_otg_vbus: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio7 12 0>;
+		};
+
+		reg_usb_host1: regulator at 2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "usb_host1_en";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio3 31 0>;
+			enable-active-high;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 0>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2
+		     &pinctrl_stmpe>;
+	status = "okay";
+
+	stmpe: stmpe1601 at 40 {
+		compatible = "st,stmpe1601";
+		reg = <0x40>;
+		interrupts = <30 0>;
+		interrupt-parent = <&gpio3>;
+
+		stmpe_gpio: stmpe_gpio {
+			compatible = "st,stmpe-gpio";
+		};
+	};
+
+	temp1: ad7414 at 4c {
+		compatible = "ad,ad7414";
+		reg = <0x4c>;
+	};
+
+	temp2: ad7414 at 4d {
+		compatible = "ad,ad7414";
+		reg = <0x4d>;
+	};
+
+	rtc: m41t62 at 68 {
+		compatible = "stm,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx6q-dmo-edmqmx6 {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x80000000
+				MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x80000000
+			>;
+		};
+
+		pinctrl_enet: enetgrp {
+			fsl,pins = <MX6QDL_ENET_PINGRP1>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <MX6QDL_I2C2_PINGRP3>;
+		};
+
+		pinctrl_stmpe: stmpegrp {
+			fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <MX6QDL_UART1_PINGRP2>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <MX6QDL_UART2_PINGRP1>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <MX6QDL_USBOTG_PINGRP1>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <MX6QDL_USDHC3_PINGRP2>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_host1>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
-- 
1.8.4.2

[PATCH v3] add support for i.MX6 based cpu modul dmo edmqmx6

[Shawn Guo]

On Thu, Nov 07, 2013 at 02:54:25PM +0100, Silvio F. wrote:
> Hi,
> 
> I hope now is all correct?!

Applied both, thanks.