From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 04/10] mtd: st_spi_fsm: Supply framework for device requests
Date: Thu, 14 Nov 2013 14:22:30 +0000 [thread overview]
Message-ID: <1384438956-31153-5-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1384438956-31153-1-git-send-email-lee.jones@linaro.org>
The FSM hardware works by setting a predetermined sequence of register
writes. Rather than open coding them inside each functional block we're
going to define them in a series of formatted 'sequence structures'.
This patch provides the framework which shall be used for every action.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
drivers/mtd/devices/st_spi_fsm.c | 49 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 49 insertions(+)
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index f560343..02619ee 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -40,11 +40,60 @@ struct stfsm {
uint32_t fifo_dir_delay;
};
+struct stfsm_seq {
+ uint32_t data_size;
+ uint32_t addr1;
+ uint32_t addr2;
+ uint32_t addr_cfg;
+ uint32_t seq_opc[5];
+ uint32_t mode;
+ uint32_t dummy;
+ uint32_t status;
+ uint8_t seq[16];
+ uint32_t seq_cfg;
+} __attribute__((__packed__, aligned(4)));
+#define STFSM_SEQ_SIZE sizeof(struct stfsm_seq)
+
+static inline int stfsm_is_idle(struct stfsm *fsm)
+{
+ return readl(fsm->base + SPI_FAST_SEQ_STA) & 0x10;
+}
+
static inline uint32_t stfsm_fifo_available(struct stfsm *fsm)
{
return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f;
}
+static inline void stfsm_load_seq(struct stfsm *fsm,
+ const struct stfsm_seq *seq)
+{
+ void __iomem *dst = fsm->base + SPI_FAST_SEQ_TRANSFER_SIZE;
+ const uint32_t *src = (const uint32_t *)seq;
+ int words = STFSM_SEQ_SIZE / sizeof(uint32_t);
+
+ BUG_ON(!stfsm_is_idle(fsm));
+
+ while (words--) {
+ writel(*src, dst);
+ src++;
+ dst += 4;
+ }
+}
+
+static void stfsm_wait_seq(struct stfsm *fsm)
+{
+ unsigned long timeo = jiffies + HZ;
+
+ while (time_before(jiffies, timeo)) {
+ if (stfsm_is_idle(fsm))
+ return;
+
+ cond_resched();
+ }
+
+ dev_err(fsm->dev, "timeout on sequence completion\n");
+}
+
static void stfsm_clear_fifo(struct stfsm *fsm)
{
uint32_t avail;
--
1.8.1.2
next prev parent reply other threads:[~2013-11-14 14:22 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-14 14:22 [PATCH 00/10] mtd: st_spi_fsm: Add new device Lee Jones
2013-11-14 14:22 ` [PATCH 01/10] mtd: st_spi_fsm: Allocate resources and register with MTD framework Lee Jones
2013-11-14 14:22 ` [PATCH 02/10] mtd: st_spi_fsm: Supply all register address and bit logic defines Lee Jones
2013-11-18 9:15 ` Linus Walleij
2013-11-18 9:32 ` Lee Jones
2013-11-18 13:39 ` Mark Brown
2013-11-18 14:24 ` Lee Jones
2013-11-18 14:45 ` Mark Brown
2013-11-18 14:56 ` Lee Jones
2013-11-18 15:16 ` Mark Brown
2013-11-18 15:31 ` Lee Jones
2013-11-18 15:41 ` Mark Brown
2013-11-18 16:02 ` Lee Jones
2013-11-18 17:22 ` Mark Brown
2013-11-18 17:32 ` Lee Jones
2013-11-18 17:59 ` Sourav Poddar
2013-11-18 18:35 ` Mark Brown
2013-11-14 14:22 ` [PATCH 03/10] mtd: st_spi_fsm: Initialise and configure the FSM for normal working conditions Lee Jones
2013-11-14 14:22 ` Lee Jones [this message]
2013-11-14 14:22 ` [PATCH 05/10] mtd: st_spi_fsm: Supply a method to read from the FSM's FIFO Lee Jones
2013-11-14 14:22 ` [PATCH 06/10] mtd: st_spi_fsm: Supply defines for the possible flash command opcodes Lee Jones
2013-11-14 14:22 ` [PATCH 07/10] mtd: st_spi_fsm: Add support for JEDEC ID extraction Lee Jones
2013-11-14 14:22 ` [PATCH 08/10] mtd: st_spi_fsm: Provide device look-up table Lee Jones
2013-11-14 14:22 ` [PATCH 09/10] mtd: st_spi_fsm: Dynamically setup flash device based on JEDEC ID Lee Jones
2013-11-14 14:22 ` [PATCH 10/10] ARM: STi: Add support for the FSM Serial Flash Controller Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1384438956-31153-5-git-send-email-lee.jones@linaro.org \
--to=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).