From: mpa@pengutronix.de (Markus Pargmann)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/8] ASoC: fsl-ssi: Move ac97 specific setup to seperate function
Date: Wed, 20 Nov 2013 10:04:15 +0100 [thread overview]
Message-ID: <1384938262-20554-2-git-send-email-mpa@pengutronix.de> (raw)
In-Reply-To: <1384938262-20554-1-git-send-email-mpa@pengutronix.de>
This is a pure cleanup patch to increase code readability.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
sound/soc/fsl/fsl_ssi.c | 57 +++++++++++++++++++++++++++----------------------
1 file changed, 32 insertions(+), 25 deletions(-)
diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
index 35e2773..fb8f52a 100644
--- a/sound/soc/fsl/fsl_ssi.c
+++ b/sound/soc/fsl/fsl_ssi.c
@@ -321,6 +321,36 @@ static irqreturn_t fsl_ssi_isr(int irq, void *dev_id)
return ret;
}
+static void fsl_ssi_setup_ac97(struct fsl_ssi_private *ssi_private)
+{
+ struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
+
+ /*
+ * Setup the clock control register
+ */
+ write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
+ &ssi->stccr);
+ write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
+ &ssi->srccr);
+
+ /*
+ * Enable AC97 mode and startup the SSI
+ */
+ write_ssi(CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV,
+ &ssi->sacnt);
+ write_ssi(0xff, &ssi->saccdis);
+ write_ssi(0x300, &ssi->saccen);
+
+ /*
+ * Enable SSI, Transmit and Receive. AC97 has to communicate with the
+ * codec before a stream is started.
+ */
+ write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_SSIEN |
+ CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE);
+
+ write_ssi(CCSR_SSI_SOR_WAIT(3), &ssi->sor);
+}
+
static int fsl_ssi_setup(struct fsl_ssi_private *ssi_private)
{
struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
@@ -387,31 +417,8 @@ static int fsl_ssi_setup(struct fsl_ssi_private *ssi_private)
* because it is also running without an active substream. Normally SSI
* is only enabled when there is a substream.
*/
- if (ssi_private->imx_ac97) {
- /*
- * Setup the clock control register
- */
- write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
- &ssi->stccr);
- write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
- &ssi->srccr);
-
- /*
- * Enable AC97 mode and startup the SSI
- */
- write_ssi(CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV,
- &ssi->sacnt);
- write_ssi(0xff, &ssi->saccdis);
- write_ssi(0x300, &ssi->saccen);
-
- /*
- * Enable SSI, Transmit and Receive
- */
- write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_SSIEN |
- CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE);
-
- write_ssi(CCSR_SSI_SOR_WAIT(3), &ssi->sor);
- }
+ if (ssi_private->imx_ac97)
+ fsl_ssi_setup_ac97(ssi_private);
return 0;
}
--
1.8.4.2
next prev parent reply other threads:[~2013-11-20 9:04 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-20 9:04 [PATCH 0/8] ASoC: fsl-ssi: offline/online configuration and cleanups Markus Pargmann
2013-11-20 9:04 ` Markus Pargmann [this message]
2013-11-21 14:24 ` [PATCH 1/8] ASoC: fsl-ssi: Move ac97 specific setup to seperate function Mark Brown
2013-11-20 9:04 ` [PATCH 2/8] ASoC: fsl-ssi: Move sysfs stats to debugfs Markus Pargmann
2013-11-21 14:22 ` Mark Brown
2013-11-22 16:42 ` Markus Pargmann
2013-11-22 18:33 ` Mark Brown
2013-11-25 9:45 ` Markus Pargmann
2013-11-20 9:04 ` [PATCH 3/8] ASoC: fsl-ssi: Add imx50-ssi and of_device_id matching Markus Pargmann
2013-11-20 12:45 ` Shawn Guo
2013-11-20 13:30 ` Markus Pargmann
2013-11-20 9:04 ` [PATCH 4/8] ASoC: fsl-ssi: Add offline_config flag Markus Pargmann
2013-11-20 9:04 ` [PATCH 5/8] ASoC: fsl-ssi: Add configuration helper functions Markus Pargmann
2013-11-20 9:04 ` [PATCH 6/8] ASoC: fsl-ssi: Move RX/TX configuration to seperate functions Markus Pargmann
2013-11-20 9:04 ` [PATCH 7/8] ASoC: fsl-ssi: Drop ac97 specific trigger function Markus Pargmann
2013-11-20 9:04 ` [PATCH 8/8] ARM: DTS: imx5* imx6*, use imx50-ssi Markus Pargmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1384938262-20554-2-git-send-email-mpa@pengutronix.de \
--to=mpa@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).