From: matt.porter@linaro.org (Matt Porter)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 9/9] ARM: dts: add usb udc support to bcm281xx
Date: Mon, 25 Nov 2013 13:16:07 -0500 [thread overview]
Message-ID: <1385403367-18144-10-git-send-email-matt.porter@linaro.org> (raw)
In-Reply-To: <1385403367-18144-1-git-send-email-matt.porter@linaro.org>
Adds USB OTG/PHY and clock support to BCM281xx and enables
UDC support on the bcm11351-brt and bcm28155-ap boards.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
---
arch/arm/boot/dts/bcm11351-brt.dts | 6 ++++++
arch/arm/boot/dts/bcm11351.dtsi | 18 ++++++++++++++++++
arch/arm/boot/dts/bcm28155-ap.dts | 8 ++++++++
3 files changed, 32 insertions(+)
diff --git a/arch/arm/boot/dts/bcm11351-brt.dts b/arch/arm/boot/dts/bcm11351-brt.dts
index 23cd16d..396b704 100644
--- a/arch/arm/boot/dts/bcm11351-brt.dts
+++ b/arch/arm/boot/dts/bcm11351-brt.dts
@@ -44,5 +44,11 @@
status = "okay";
};
+ usbotg: usb at 3f120000 {
+ status = "okay";
+ };
+ usbphy: usb-phy at 3f130000 {
+ status = "okay";
+ };
};
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
index 1246885..868879a 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@@ -243,4 +243,22 @@
#clock-cells = <0>;
};
};
+
+ usbotg: usb at 3f120000 {
+ compatible = "snps,dwc2";
+ reg = <0x3f120000 0x10000>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_otg_ahb_clk>;
+ clock-names = "otg";
+ phys = <&usbphy>;
+ phy-names = "device";
+ status = "disabled";
+ };
+
+ usbphy: usb-phy at 3f130000 {
+ compatible = "brcm,kona-usb2-phy";
+ reg = <0x3f130000 0x28>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
};
diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts
index 08e47c2..a3bc436 100644
--- a/arch/arm/boot/dts/bcm28155-ap.dts
+++ b/arch/arm/boot/dts/bcm28155-ap.dts
@@ -43,4 +43,12 @@
cd-gpios = <&gpio 14 0>;
status = "okay";
};
+
+ usbotg: usb at 3f120000 {
+ status = "okay";
+ };
+
+ usbphy: usb-phy at 3f130000 {
+ status = "okay";
+ };
};
--
1.8.4
next prev parent reply other threads:[~2013-11-25 18:16 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-25 18:15 [PATCH v3 0/9] USB Device Controller support for BCM281xx Matt Porter
2013-11-25 18:15 ` [PATCH v3 1/9] phy: add phy_get_bus_width()/phy_set_bus_width() calls Matt Porter
2013-11-26 10:16 ` Kishon Vijay Abraham I
2013-11-27 16:55 ` Matt Porter
2013-11-25 18:16 ` [PATCH v3 2/9] staging: dwc2: update DT binding to add generic clock/phy properties Matt Porter
2013-11-26 10:19 ` Kishon Vijay Abraham I
2013-11-27 16:56 ` Matt Porter
2013-11-25 18:16 ` [PATCH v3 3/9] usb: gadget: s3c-hsotg: enable build for other platforms Matt Porter
2013-11-25 18:16 ` [PATCH v3 4/9] usb: gadget: s3c-hsotg: add snps, dwc2 compatible string Matt Porter
2013-11-25 18:16 ` [PATCH v3 5/9] usb: gadget: s3c-hsotg: use generic phy_init()/phy_exit() support Matt Porter
2013-11-26 10:23 ` Kishon Vijay Abraham I
2013-11-27 17:13 ` Matt Porter
2013-11-27 22:36 ` Matt Porter
2013-11-28 5:53 ` Kishon Vijay Abraham I
2013-11-28 16:41 ` Matt Porter
2013-11-28 17:02 ` Kamil Debski
2013-11-25 18:16 ` [PATCH v3 6/9] usb: gadget: s3c-hsotg: get phy bus width from phy subsystem Matt Porter
2013-11-26 10:28 ` Kishon Vijay Abraham I
2013-11-27 17:16 ` Matt Porter
2013-11-25 18:16 ` [PATCH v3 7/9] phy: add Broadcom Kona USB2 PHY DT binding Matt Porter
2013-11-26 10:31 ` Kishon Vijay Abraham I
2013-11-27 17:19 ` Matt Porter
2013-11-25 18:16 ` [PATCH v3 8/9] phy: add Broadcom Kona USB2 PHY driver Matt Porter
2013-11-27 8:51 ` Kishon Vijay Abraham I
2013-11-27 17:21 ` Matt Porter
2013-11-25 18:16 ` Matt Porter [this message]
2013-11-27 8:57 ` [PATCH v3 9/9] ARM: dts: add usb udc support to bcm281xx Kishon Vijay Abraham I
2013-11-27 17:24 ` Matt Porter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1385403367-18144-10-git-send-email-matt.porter@linaro.org \
--to=matt.porter@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).