* [PATCH 0/2] Enable I2C on bcm28155-ap
@ 2013-12-06 23:45 Tim Kryger
2013-12-06 23:45 ` [PATCH 1/2] ARM: dts: bcm281xx: Add i2c busses Tim Kryger
2013-12-06 23:45 ` [PATCH 2/2] ARM: dts: bcm28155-ap: Enable all the " Tim Kryger
0 siblings, 2 replies; 5+ messages in thread
From: Tim Kryger @ 2013-12-06 23:45 UTC (permalink / raw)
To: linux-arm-kernel
This series enables all the I2C busses on the bcm28155-ap board.
These patches appeared in another series that was partially accepted.
https://lkml.org/lkml/2013/11/14/517
It depends on: https://lkml.org/lkml/2013/12/5/508
Tim Kryger (2):
ARM: dts: bcm281xx: Add i2c busses
ARM: dts: bcm28155-ap: Enable all the i2c busses
arch/arm/boot/dts/bcm11351.dtsi | 40 +++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm28155-ap.dts | 20 ++++++++++++++++++++
2 files changed, 60 insertions(+)
--
1.8.0.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] ARM: dts: bcm281xx: Add i2c busses
2013-12-06 23:45 [PATCH 0/2] Enable I2C on bcm28155-ap Tim Kryger
@ 2013-12-06 23:45 ` Tim Kryger
2013-12-10 7:28 ` Christian Daudt
2013-12-06 23:45 ` [PATCH 2/2] ARM: dts: bcm28155-ap: Enable all the " Tim Kryger
1 sibling, 1 reply; 5+ messages in thread
From: Tim Kryger @ 2013-12-06 23:45 UTC (permalink / raw)
To: linux-arm-kernel
Add the DTS nodes for all the i2c busses in the SoC.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
---
arch/arm/boot/dts/bcm11351.dtsi | 40 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
index 1246885..4bfd7e3 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@@ -146,6 +146,46 @@
status = "disabled";
};
+ i2c at 3e016000 {
+ compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+ reg = <0x3e016000 0x80>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&bsc1_clk>;
+ status = "disabled";
+ };
+
+ i2c at 3e017000 {
+ compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+ reg = <0x3e017000 0x80>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&bsc2_clk>;
+ status = "disabled";
+ };
+
+ i2c at 3e018000 {
+ compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+ reg = <0x3e018000 0x80>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&bsc3_clk>;
+ status = "disabled";
+ };
+
+ i2c at 3500d000 {
+ compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
+ reg = <0x3500d000 0x80>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&pmu_bsc_clk>;
+ status = "disabled";
+ };
+
clocks {
bsc1_clk: bsc1 {
compatible = "fixed-clock";
--
1.8.0.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] ARM: dts: bcm28155-ap: Enable all the i2c busses
2013-12-06 23:45 [PATCH 0/2] Enable I2C on bcm28155-ap Tim Kryger
2013-12-06 23:45 ` [PATCH 1/2] ARM: dts: bcm281xx: Add i2c busses Tim Kryger
@ 2013-12-06 23:45 ` Tim Kryger
2013-12-10 7:07 ` Christian Daudt
1 sibling, 1 reply; 5+ messages in thread
From: Tim Kryger @ 2013-12-06 23:45 UTC (permalink / raw)
To: linux-arm-kernel
Enable all available i2c busses.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
---
arch/arm/boot/dts/bcm28155-ap.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts
index 08e47c2..bab302d 100644
--- a/arch/arm/boot/dts/bcm28155-ap.dts
+++ b/arch/arm/boot/dts/bcm28155-ap.dts
@@ -27,6 +27,26 @@
status = "okay";
};
+ i2c at 3e016000 {
+ status="okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c at 3e017000 {
+ status="okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c at 3e018000 {
+ status="okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c at 3500d000 {
+ status="okay";
+ clock-frequency = <400000>;
+ };
+
sdio1: sdio at 3f180000 {
max-frequency = <48000000>;
status = "okay";
--
1.8.0.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] ARM: dts: bcm28155-ap: Enable all the i2c busses
2013-12-06 23:45 ` [PATCH 2/2] ARM: dts: bcm28155-ap: Enable all the " Tim Kryger
@ 2013-12-10 7:07 ` Christian Daudt
0 siblings, 0 replies; 5+ messages in thread
From: Christian Daudt @ 2013-12-10 7:07 UTC (permalink / raw)
To: linux-arm-kernel
Applied to armsoc/for-3.14/dt
thanks,
csd
On Fri, Dec 6, 2013 at 3:45 PM, Tim Kryger <tim.kryger@linaro.org> wrote:
> Enable all available i2c busses.
>
> Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
> Reviewed-by: Christian Daudt <csd@broadcom.com>
> Reviewed-by: Matt Porter <matt.porter@linaro.org>
> Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
> ---
> arch/arm/boot/dts/bcm28155-ap.dts | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts
> index 08e47c2..bab302d 100644
> --- a/arch/arm/boot/dts/bcm28155-ap.dts
> +++ b/arch/arm/boot/dts/bcm28155-ap.dts
> @@ -27,6 +27,26 @@
> status = "okay";
> };
>
> + i2c at 3e016000 {
> + status="okay";
> + clock-frequency = <400000>;
> + };
> +
> + i2c at 3e017000 {
> + status="okay";
> + clock-frequency = <400000>;
> + };
> +
> + i2c at 3e018000 {
> + status="okay";
> + clock-frequency = <400000>;
> + };
> +
> + i2c at 3500d000 {
> + status="okay";
> + clock-frequency = <400000>;
> + };
> +
> sdio1: sdio at 3f180000 {
> max-frequency = <48000000>;
> status = "okay";
> --
> 1.8.0.1
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] ARM: dts: bcm281xx: Add i2c busses
2013-12-06 23:45 ` [PATCH 1/2] ARM: dts: bcm281xx: Add i2c busses Tim Kryger
@ 2013-12-10 7:28 ` Christian Daudt
0 siblings, 0 replies; 5+ messages in thread
From: Christian Daudt @ 2013-12-10 7:28 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 6, 2013 at 3:45 PM, Tim Kryger <tim.kryger@linaro.org> wrote:
> Add the DTS nodes for all the i2c busses in the SoC.
>
> Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
> Reviewed-by: Christian Daudt <csd@broadcom.com>
> Reviewed-by: Matt Porter <matt.porter@linaro.org>
> Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
> ---
> arch/arm/boot/dts/bcm11351.dtsi | 40 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
>
> diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
> index 1246885..4bfd7e3 100644
> --- a/arch/arm/boot/dts/bcm11351.dtsi
> +++ b/arch/arm/boot/dts/bcm11351.dtsi
> @@ -146,6 +146,46 @@
> status = "disabled";
> };
>
> + i2c at 3e016000 {
> + compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
> + reg = <0x3e016000 0x80>;
> + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&bsc1_clk>;
> + status = "disabled";
> + };
> +
> + i2c at 3e017000 {
> + compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
> + reg = <0x3e017000 0x80>;
> + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&bsc2_clk>;
> + status = "disabled";
> + };
> +
> + i2c at 3e018000 {
> + compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
> + reg = <0x3e018000 0x80>;
> + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&bsc3_clk>;
> + status = "disabled";
> + };
> +
> + i2c at 3500d000 {
> + compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
> + reg = <0x3500d000 0x80>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&pmu_bsc_clk>;
> + status = "disabled";
> + };
> +
> clocks {
> bsc1_clk: bsc1 {
> compatible = "fixed-clock";
> --
> 1.8.0.1
>
Applied to armsoc/for-3.14/dt
thanks,
csd
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2013-12-10 7:28 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-12-06 23:45 [PATCH 0/2] Enable I2C on bcm28155-ap Tim Kryger
2013-12-06 23:45 ` [PATCH 1/2] ARM: dts: bcm281xx: Add i2c busses Tim Kryger
2013-12-10 7:28 ` Christian Daudt
2013-12-06 23:45 ` [PATCH 2/2] ARM: dts: bcm28155-ap: Enable all the " Tim Kryger
2013-12-10 7:07 ` Christian Daudt
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).