* [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support @ 2014-01-23 2:13 Fabio Estevam 2014-01-23 2:13 ` [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support Fabio Estevam 2014-01-28 12:08 ` [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support Shawn Guo 0 siblings, 2 replies; 6+ messages in thread From: Fabio Estevam @ 2014-01-23 2:13 UTC (permalink / raw) To: linux-arm-kernel From: Fabio Estevam <fabio.estevam@freescale.com> imx6sl-evk board has Freescale PFUZE100 regulator, so add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> --- arch/arm/boot/dts/imx6sl-evk.dts | 110 ++++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6sl-pingrp.h | 4 ++ 2 files changed, 114 insertions(+) diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts index f23b5d1..5ba15ab 100644 --- a/arch/arm/boot/dts/imx6sl-evk.dts +++ b/arch/arm/boot/dts/imx6sl-evk.dts @@ -46,6 +46,112 @@ }; }; +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pfuze100 at 08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + &ecspi1 { fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio4 11 0>; @@ -86,6 +192,10 @@ >; }; + pinctrl_i2c1: i2c1grp { + fsl,pins = <MX6SL_I2C1_PINGRP1>; + }; + pinctrl_ecspi1: ecspi1grp { fsl,pins = <MX6SL_ECSPI1_PINGRP1>; }; diff --git a/arch/arm/boot/dts/imx6sl-pingrp.h b/arch/arm/boot/dts/imx6sl-pingrp.h index ead26d4..cada37a 100644 --- a/arch/arm/boot/dts/imx6sl-pingrp.h +++ b/arch/arm/boot/dts/imx6sl-pingrp.h @@ -15,6 +15,10 @@ MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 \ MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x100b1 +#define MX6SL_I2C1_PINGRP1 \ + MX6SL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1 \ + MX6SL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1 + #define MX6SL_FEC_PINGRP1 \ MX6SL_PAD_FEC_MDC__FEC_MDC 0x1b0b0 \ MX6SL_PAD_FEC_MDIO__FEC_MDIO 0x1b0b0 \ -- 1.8.1.2 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support 2014-01-23 2:13 [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support Fabio Estevam @ 2014-01-23 2:13 ` Fabio Estevam 2014-01-28 12:12 ` Shawn Guo 2014-01-28 12:08 ` [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support Shawn Guo 1 sibling, 1 reply; 6+ messages in thread From: Fabio Estevam @ 2014-01-23 2:13 UTC (permalink / raw) To: linux-arm-kernel From: Fabio Estevam <fabio.estevam@freescale.com> imx6sl-evk has a wm8962 codec. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> --- arch/arm/boot/dts/imx6sl-evk.dts | 72 +++++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6sl-pingrp.h | 11 ++++++ arch/arm/boot/dts/imx6sl.dtsi | 3 ++ 3 files changed, 86 insertions(+) diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts index 5ba15ab..9e1ab77 100644 --- a/arch/arm/boot/dts/imx6sl-evk.dts +++ b/arch/arm/boot/dts/imx6sl-evk.dts @@ -24,6 +24,22 @@ #address-cells = <1>; #size-cells = <0>; + reg_aud3v: wm8962_supply_3v15 { + compatible = "regulator-fixed"; + regulator-name = "wm8962-supply-3v15"; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3150000>; + regulator-boot-on; + }; + + reg_aud4v: wm8962_supply_4v2 { + compatible = "regulator-fixed"; + regulator-name = "wm8962-supply-4v2"; + regulator-min-microvolt = <4325000>; + regulator-max-microvolt = <4325000>; + regulator-boot-on; + }; + reg_usb_otg1_vbus: regulator at 0 { compatible = "regulator-fixed"; reg = <0>; @@ -44,6 +60,28 @@ enable-active-high; }; }; + + sound { + compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "AMIC", "MICBIAS", + "IN3R", "AMIC"; + mux-int-port = <2>; + mux-ext-port = <3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux3>; + status = "okay"; }; &i2c1 { @@ -152,6 +190,27 @@ }; }; +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + codec: wm8962 at 1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; + clocks = <&clks IMX6SL_CLK_EXTERN_AUDIO>; + DCVDD-supply = <&vgen3_reg>; + DBVDD-supply = <®_aud3v>; + AVDD-supply = <&vgen3_reg>; + CPVDD-supply = <&vgen3_reg>; + MICVDD-supply = <®_aud3v>; + PLLVDD-supply = <&vgen3_reg>; + SPKVDD1-supply = <®_aud4v>; + SPKVDD2-supply = <®_aud4v>; + }; +}; + &ecspi1 { fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio4 11 0>; @@ -192,10 +251,18 @@ >; }; + pinctrl_audmux3: audmux3grp { + fsl,pins = <MX6SL_AUDMUX3_PINGRP1>; + }; + pinctrl_i2c1: i2c1grp { fsl,pins = <MX6SL_I2C1_PINGRP1>; }; + pinctrl_i2c2: i2c2grp { + fsl,pins = <MX6SL_I2C2_PINGRP1>; + }; + pinctrl_ecspi1: ecspi1grp { fsl,pins = <MX6SL_ECSPI1_PINGRP1>; }; @@ -277,6 +344,11 @@ status = "okay"; }; +&ssi2 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; diff --git a/arch/arm/boot/dts/imx6sl-pingrp.h b/arch/arm/boot/dts/imx6sl-pingrp.h index cada37a..ee50ace 100644 --- a/arch/arm/boot/dts/imx6sl-pingrp.h +++ b/arch/arm/boot/dts/imx6sl-pingrp.h @@ -10,6 +10,13 @@ #ifndef __DTS_IMX6SL_PINGRP_H #define __DTS_IMX6SL_PINGRP_H +#define MX6SL_AUDMUX3_PINGRP1 \ + MX6SL_PAD_AUD_RXD__AUD3_RXD 0x4130B0 \ + MX6SL_PAD_AUD_TXC__AUD3_TXC 0x4130B0 \ + MX6SL_PAD_AUD_TXD__AUD3_TXD 0x4110B0 \ + MX6SL_PAD_AUD_TXFS__AUD3_TXFS 0x4130B0 \ + MX6SL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130B0 + #define MX6SL_ECSPI1_PINGRP1 \ MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO 0x100b1 \ MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 \ @@ -19,6 +26,10 @@ MX6SL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1 \ MX6SL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1 +#define MX6SL_I2C2_PINGRP1 \ + MX6SL_PAD_I2C2_SCL__I2C2_SCL 0x4001b8b1 \ + MX6SL_PAD_I2C2_SDA__I2C2_SDA 0x4001b8b1 + #define MX6SL_FEC_PINGRP1 \ MX6SL_PAD_FEC_MDC__FEC_MDC 0x1b0b0 \ MX6SL_PAD_FEC_MDIO__FEC_MDIO 0x1b0b0 \ diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index 95bb37b..04cf457 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -236,6 +236,7 @@ <&sdma 38 1 0>; dma-names = "rx", "tx"; fsl,fifo-depth = <15>; + fsl,ssi-dma-events = <38 37>; status = "disabled"; }; @@ -250,6 +251,7 @@ <&sdma 42 1 0>; dma-names = "rx", "tx"; fsl,fifo-depth = <15>; + fsl,ssi-dma-events = <42 41>; status = "disabled"; }; @@ -264,6 +266,7 @@ <&sdma 46 1 0>; dma-names = "rx", "tx"; fsl,fifo-depth = <15>; + fsl,ssi-dma-events = <46 45>; status = "disabled"; }; -- 1.8.1.2 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support 2014-01-23 2:13 ` [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support Fabio Estevam @ 2014-01-28 12:12 ` Shawn Guo 2014-01-28 12:14 ` Fabio Estevam 0 siblings, 1 reply; 6+ messages in thread From: Shawn Guo @ 2014-01-28 12:12 UTC (permalink / raw) To: linux-arm-kernel On Thu, Jan 23, 2014 at 12:13:33AM -0200, Fabio Estevam wrote: > From: Fabio Estevam <fabio.estevam@freescale.com> > > imx6sl-evk has a wm8962 codec. Add support for it. > > Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> > --- > arch/arm/boot/dts/imx6sl-evk.dts | 72 +++++++++++++++++++++++++++++++++++++++ > arch/arm/boot/dts/imx6sl-pingrp.h | 11 ++++++ > arch/arm/boot/dts/imx6sl.dtsi | 3 ++ > 3 files changed, 86 insertions(+) > > diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts > index 5ba15ab..9e1ab77 100644 > --- a/arch/arm/boot/dts/imx6sl-evk.dts > +++ b/arch/arm/boot/dts/imx6sl-evk.dts > @@ -24,6 +24,22 @@ > #address-cells = <1>; > #size-cells = <0>; > > + reg_aud3v: wm8962_supply_3v15 { Have node name in generic reglator at num form. > + compatible = "regulator-fixed"; > + regulator-name = "wm8962-supply-3v15"; > + regulator-min-microvolt = <3150000>; > + regulator-max-microvolt = <3150000>; > + regulator-boot-on; > + }; > + > + reg_aud4v: wm8962_supply_4v2 { > + compatible = "regulator-fixed"; > + regulator-name = "wm8962-supply-4v2"; > + regulator-min-microvolt = <4325000>; > + regulator-max-microvolt = <4325000>; > + regulator-boot-on; > + }; > + > reg_usb_otg1_vbus: regulator at 0 { > compatible = "regulator-fixed"; > reg = <0>; > @@ -44,6 +60,28 @@ > enable-active-high; > }; > }; > + > + sound { > + compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962"; > + model = "wm8962-audio"; > + ssi-controller = <&ssi2>; > + audio-codec = <&codec>; > + audio-routing = > + "Headphone Jack", "HPOUTL", > + "Headphone Jack", "HPOUTR", > + "Ext Spk", "SPKOUTL", > + "Ext Spk", "SPKOUTR", > + "AMIC", "MICBIAS", > + "IN3R", "AMIC"; > + mux-int-port = <2>; > + mux-ext-port = <3>; > + }; > +}; > + > +&audmux { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux3>; > + status = "okay"; > }; > > &i2c1 { > @@ -152,6 +190,27 @@ > }; > }; > > +&i2c2 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + codec: wm8962 at 1a { > + compatible = "wlf,wm8962"; > + reg = <0x1a>; > + clocks = <&clks IMX6SL_CLK_EXTERN_AUDIO>; > + DCVDD-supply = <&vgen3_reg>; > + DBVDD-supply = <®_aud3v>; > + AVDD-supply = <&vgen3_reg>; > + CPVDD-supply = <&vgen3_reg>; > + MICVDD-supply = <®_aud3v>; > + PLLVDD-supply = <&vgen3_reg>; > + SPKVDD1-supply = <®_aud4v>; > + SPKVDD2-supply = <®_aud4v>; > + }; > +}; > + > &ecspi1 { > fsl,spi-num-chipselects = <1>; > cs-gpios = <&gpio4 11 0>; > @@ -192,10 +251,18 @@ > >; > }; > > + pinctrl_audmux3: audmux3grp { > + fsl,pins = <MX6SL_AUDMUX3_PINGRP1>; > + }; > + > pinctrl_i2c1: i2c1grp { > fsl,pins = <MX6SL_I2C1_PINGRP1>; > }; > > + pinctrl_i2c2: i2c2grp { > + fsl,pins = <MX6SL_I2C2_PINGRP1>; > + }; > + > pinctrl_ecspi1: ecspi1grp { > fsl,pins = <MX6SL_ECSPI1_PINGRP1>; > }; > @@ -277,6 +344,11 @@ > status = "okay"; > }; > > +&ssi2 { > + fsl,mode = "i2s-slave"; > + status = "okay"; > +}; > + > &uart1 { > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_uart1>; > diff --git a/arch/arm/boot/dts/imx6sl-pingrp.h b/arch/arm/boot/dts/imx6sl-pingrp.h > index cada37a..ee50ace 100644 > --- a/arch/arm/boot/dts/imx6sl-pingrp.h > +++ b/arch/arm/boot/dts/imx6sl-pingrp.h > @@ -10,6 +10,13 @@ > #ifndef __DTS_IMX6SL_PINGRP_H > #define __DTS_IMX6SL_PINGRP_H > > +#define MX6SL_AUDMUX3_PINGRP1 \ > + MX6SL_PAD_AUD_RXD__AUD3_RXD 0x4130B0 \ > + MX6SL_PAD_AUD_TXC__AUD3_TXC 0x4130B0 \ > + MX6SL_PAD_AUD_TXD__AUD3_TXD 0x4110B0 \ > + MX6SL_PAD_AUD_TXFS__AUD3_TXFS 0x4130B0 \ > + MX6SL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130B0 > + > #define MX6SL_ECSPI1_PINGRP1 \ > MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO 0x100b1 \ > MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 \ > @@ -19,6 +26,10 @@ > MX6SL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1 \ > MX6SL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1 > > +#define MX6SL_I2C2_PINGRP1 \ > + MX6SL_PAD_I2C2_SCL__I2C2_SCL 0x4001b8b1 \ > + MX6SL_PAD_I2C2_SDA__I2C2_SDA 0x4001b8b1 > + > #define MX6SL_FEC_PINGRP1 \ > MX6SL_PAD_FEC_MDC__FEC_MDC 0x1b0b0 \ > MX6SL_PAD_FEC_MDIO__FEC_MDIO 0x1b0b0 \ > diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi > index 95bb37b..04cf457 100644 > --- a/arch/arm/boot/dts/imx6sl.dtsi > +++ b/arch/arm/boot/dts/imx6sl.dtsi > @@ -236,6 +236,7 @@ > <&sdma 38 1 0>; > dma-names = "rx", "tx"; > fsl,fifo-depth = <15>; > + fsl,ssi-dma-events = <38 37>; Do you still need this custom property? Shawn > status = "disabled"; > }; > > @@ -250,6 +251,7 @@ > <&sdma 42 1 0>; > dma-names = "rx", "tx"; > fsl,fifo-depth = <15>; > + fsl,ssi-dma-events = <42 41>; > status = "disabled"; > }; > > @@ -264,6 +266,7 @@ > <&sdma 46 1 0>; > dma-names = "rx", "tx"; > fsl,fifo-depth = <15>; > + fsl,ssi-dma-events = <46 45>; > status = "disabled"; > }; > > -- > 1.8.1.2 > ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support 2014-01-28 12:12 ` Shawn Guo @ 2014-01-28 12:14 ` Fabio Estevam 2014-01-28 12:33 ` Shawn Guo 0 siblings, 1 reply; 6+ messages in thread From: Fabio Estevam @ 2014-01-28 12:14 UTC (permalink / raw) To: linux-arm-kernel On Tue, Jan 28, 2014 at 10:12 AM, Shawn Guo <shawn.guo@linaro.org> wrote: >> diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi >> index 95bb37b..04cf457 100644 >> --- a/arch/arm/boot/dts/imx6sl.dtsi >> +++ b/arch/arm/boot/dts/imx6sl.dtsi >> @@ -236,6 +236,7 @@ >> <&sdma 38 1 0>; >> dma-names = "rx", "tx"; >> fsl,fifo-depth = <15>; >> + fsl,ssi-dma-events = <38 37>; > > Do you still need this custom property? I can get rid of it. Should I remove from the other SoCs as well? Regards, Fabio Estevam ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support 2014-01-28 12:14 ` Fabio Estevam @ 2014-01-28 12:33 ` Shawn Guo 0 siblings, 0 replies; 6+ messages in thread From: Shawn Guo @ 2014-01-28 12:33 UTC (permalink / raw) To: linux-arm-kernel On Tue, Jan 28, 2014 at 10:14:55AM -0200, Fabio Estevam wrote: > On Tue, Jan 28, 2014 at 10:12 AM, Shawn Guo <shawn.guo@linaro.org> wrote: > > >> diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi > >> index 95bb37b..04cf457 100644 > >> --- a/arch/arm/boot/dts/imx6sl.dtsi > >> +++ b/arch/arm/boot/dts/imx6sl.dtsi > >> @@ -236,6 +236,7 @@ > >> <&sdma 38 1 0>; > >> dma-names = "rx", "tx"; > >> fsl,fifo-depth = <15>; > >> + fsl,ssi-dma-events = <38 37>; > > > > Do you still need this custom property? > > I can get rid of it. > > Should I remove from the other SoCs as well? We have the requirement that a newer kernel must work with all the older DTBs. But I haven't heard too much about the opposite - a newer DTB needs to work with all the older kernel. If that's case, we can remove it from other SoCs as well, since the latest kernel already moves to generic DMA bindings. Shawn ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support 2014-01-23 2:13 [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support Fabio Estevam 2014-01-23 2:13 ` [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support Fabio Estevam @ 2014-01-28 12:08 ` Shawn Guo 1 sibling, 0 replies; 6+ messages in thread From: Shawn Guo @ 2014-01-28 12:08 UTC (permalink / raw) To: linux-arm-kernel On Thu, Jan 23, 2014 at 12:13:32AM -0200, Fabio Estevam wrote: > From: Fabio Estevam <fabio.estevam@freescale.com> > > imx6sl-evk board has Freescale PFUZE100 regulator, so add support for it. > > Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> > --- > arch/arm/boot/dts/imx6sl-evk.dts | 110 ++++++++++++++++++++++++++++++++++++++ > arch/arm/boot/dts/imx6sl-pingrp.h | 4 ++ > 2 files changed, 114 insertions(+) > > diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts > index f23b5d1..5ba15ab 100644 > --- a/arch/arm/boot/dts/imx6sl-evk.dts > +++ b/arch/arm/boot/dts/imx6sl-evk.dts > @@ -46,6 +46,112 @@ > }; > }; > > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + pmic: pfuze100 at 08 { > + compatible = "fsl,pfuze100"; > + reg = <0x08>; > + > + regulators { > + sw1a_reg: sw1ab { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <6250>; > + }; > + > + sw1c_reg: sw1c { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <6250>; > + }; > + > + sw2_reg: sw2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3a_reg: sw3a { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3b_reg: sw3b { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw4_reg: sw4 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + swbst_reg: swbst { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5150000>; > + }; > + > + snvs_reg: vsnvs { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <3000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vref_reg: vrefddr { > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vgen1_reg: vgen1 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen2_reg: vgen2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen3_reg: vgen3 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vgen4_reg: vgen4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen5_reg: vgen5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen6_reg: vgen6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > + }; > +}; > + > &ecspi1 { > fsl,spi-num-chipselects = <1>; > cs-gpios = <&gpio4 11 0>; > @@ -86,6 +192,10 @@ > >; > }; > > + pinctrl_i2c1: i2c1grp { > + fsl,pins = <MX6SL_I2C1_PINGRP1>; > + }; > + > pinctrl_ecspi1: ecspi1grp { > fsl,pins = <MX6SL_ECSPI1_PINGRP1>; > }; > diff --git a/arch/arm/boot/dts/imx6sl-pingrp.h b/arch/arm/boot/dts/imx6sl-pingrp.h > index ead26d4..cada37a 100644 > --- a/arch/arm/boot/dts/imx6sl-pingrp.h > +++ b/arch/arm/boot/dts/imx6sl-pingrp.h > @@ -15,6 +15,10 @@ > MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 \ > MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x100b1 > > +#define MX6SL_I2C1_PINGRP1 \ > + MX6SL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1 \ > + MX6SL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1 > + The PINGRP is gone. Shawn > #define MX6SL_FEC_PINGRP1 \ > MX6SL_PAD_FEC_MDC__FEC_MDC 0x1b0b0 \ > MX6SL_PAD_FEC_MDIO__FEC_MDIO 0x1b0b0 \ > -- > 1.8.1.2 > ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-01-28 12:33 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-01-23 2:13 [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support Fabio Estevam 2014-01-23 2:13 ` [PATCH 2/2] ARM: dts: imx6sl-evk: Add audio support Fabio Estevam 2014-01-28 12:12 ` Shawn Guo 2014-01-28 12:14 ` Fabio Estevam 2014-01-28 12:33 ` Shawn Guo 2014-01-28 12:08 ` [PATCH 1/2] ARM: dts: imx6sl-evk: Add PFUZE100 support Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).