From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 35/35] ARM: STi: Add support for the FSM Serial Flash Controller
Date: Tue, 18 Feb 2014 14:56:02 +0000 [thread overview]
Message-ID: <1392735362-1245-36-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1392735362-1245-1-git-send-email-lee.jones@linaro.org>
Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
arch/arm/boot/dts/stih416-b2105.dts | 14 ++++++++++++++
arch/arm/boot/dts/stih416-pinctrl.dtsi | 12 ++++++++++++
2 files changed, 26 insertions(+)
diff --git a/arch/arm/boot/dts/stih416-b2105.dts b/arch/arm/boot/dts/stih416-b2105.dts
index e518eb0..dd7ac88 100644
--- a/arch/arm/boot/dts/stih416-b2105.dts
+++ b/arch/arm/boot/dts/stih416-b2105.dts
@@ -33,6 +33,20 @@
status = "okay";
};
+ /* FSM */
+ spifsm: spifsm at fe902000{
+ compatible = "st,spi-fsm";
+ reg = <0xfe902000 0x1000>;
+ reg-names = "spi-fsm";
+ pinctrl-0 = <&pinctrl_fsm>;
+
+ st,syscfg = <&syscfg_rear>;
+ st,boot-device-reg = <0x958>;
+ st,boot-device-spi = <0x1a>;
+
+ status = "okay";
+ };
+
leds {
compatible = "gpio-leds";
fp_led {
diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
index 10bb4df..9a48710 100644
--- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
@@ -235,6 +235,18 @@
};
};
+ fsm {
+ pinctrl_fsm: fsm {
+ st,pins {
+ spi-fsm-clk = <&PIO12 2 OUT ALT1>;
+ spi-fsm-cs = <&PIO12 3 OUT ALT1>;
+ spi-fsm-mosi = <&PIO12 4 OUT ALT1>;
+ spi-fsm-miso = <&PIO12 5 IN ALT1>;
+ spi-fsm-hol = <&PIO12 6 OUT ALT1>;
+ spi-fsm-wp = <&PIO12 7 OUT ALT1>;
+ };
+ };
+ };
};
pin-controller-rear {
--
1.8.3.2
next prev parent reply other threads:[~2014-02-18 14:56 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-18 14:55 [PATCH v5 00/35] mtd: st_spi_fsm: Add new driver Lee Jones
2014-02-18 14:55 ` [PATCH 01/35] mtd: st_spi_fsm: Allocate resources and register with MTD framework Lee Jones
2014-03-09 5:33 ` Brian Norris
2014-03-11 8:23 ` [PATCH v6 " Lee Jones
2014-03-20 7:10 ` Brian Norris
2014-02-18 14:55 ` [PATCH 02/35] mtd: st_spi_fsm: Supply all register address and bit logic defines Lee Jones
2014-02-18 14:55 ` [PATCH 03/35] mtd: st_spi_fsm: Initialise and configure the FSM for normal working conditions Lee Jones
2014-02-18 14:55 ` [PATCH 04/35] mtd: st_spi_fsm: Supply framework for device requests Lee Jones
2014-02-18 14:55 ` [PATCH 05/35] mtd: st_spi_fsm: Supply a method to read from the FSM's FIFO Lee Jones
2014-02-18 14:55 ` [PATCH 06/35] mtd: st_spi_fsm: Add support for JEDEC ID extraction Lee Jones
2014-02-18 14:55 ` [PATCH 07/35] mtd: devices: Provide header for shared OPCODEs and SFDP commands Lee Jones
2014-02-18 14:55 ` [PATCH 08/35] mtd: st_spi_fsm: Provide device look-up table Lee Jones
2014-02-18 14:55 ` [PATCH 09/35] mtd: st_spi_fsm: Dynamically setup flash device based on JEDEC ID Lee Jones
2014-02-18 14:55 ` [PATCH 10/35] mtd: st_spi_fsm: Search for preferred FSM message sequence configurations Lee Jones
2014-02-18 14:55 ` [PATCH 11/35] mtd: st_spi_fsm: Use device size to determine address width Lee Jones
2014-03-20 7:30 ` Brian Norris
2014-02-18 14:55 ` [PATCH 12/35] mtd: st_spi_fsm: Prepare the read/write FSM message sequence(s) Lee Jones
2014-02-18 14:55 ` [PATCH 13/35] mtd: st_spi_fsm: Add device-tree binding documentation Lee Jones
2014-02-18 14:55 ` [PATCH 14/35] mtd: st_spi_fsm: Fetch boot-device from mode pins Lee Jones
2014-02-18 14:55 ` [PATCH 15/35] mtd: st_spi_fsm: Provide the erase one sector sequence Lee Jones
2014-02-18 14:55 ` [PATCH 16/35] mtd: st_spi_fsm: Provide the sequence for enabling 32bit addressing mode Lee Jones
2014-02-18 14:55 ` [PATCH 17/35] mtd: st_spi_fsm: Prepare read/write sequences according to configuration Lee Jones
2014-02-18 14:55 ` [PATCH 18/35] mtd: st_spi_fsm: Add a check to if the chip can handle an SoC reset Lee Jones
2014-02-18 14:55 ` [PATCH 19/35] mtd: st_spi_fsm: Provide a method to put the chip into 32bit addressing mode Lee Jones
2014-02-18 14:55 ` [PATCH 20/35] mtd: st_spi_fsm: Update the flash Volatile Configuration Register Lee Jones
2014-02-18 14:55 ` [PATCH 21/35] mtd: st_spi_fsm: Provide the default read/write configurations Lee Jones
2014-02-18 14:55 ` [PATCH 22/35] mtd: st_spi_fsm: Supply the N25Qxxx specific read configurations Lee Jones
2014-02-18 14:55 ` [PATCH 23/35] mtd: st_spi_fsm: Supply the N25Qxxx chip specific configuration call-back Lee Jones
2014-02-18 14:55 ` [PATCH 24/35] mtd: st_spi_fsm: Prepare default sequences for read/write/erase Lee Jones
2014-02-18 14:55 ` [PATCH 25/35] mtd: st_spi_fsm: Add the ability to read from a Serial Flash device Lee Jones
2014-03-20 7:55 ` Brian Norris
2014-02-18 14:55 ` [PATCH 26/35] mtd: st_spi_fsm: Write to Flash via the FSM FIFO Lee Jones
2014-02-18 14:55 ` [PATCH 27/35] mtd: st_spi_fsm: Supply a busy wait for post-write status Lee Jones
2014-03-20 7:27 ` Brian Norris
2014-02-18 14:55 ` [PATCH 28/35] mtd: st_spi_fsm: Erase partly or as a whole a Serial Flash device Lee Jones
2014-02-18 14:55 ` [PATCH 29/35] mtd: st_spi_fsm: Add the ability to read the FSM's status Lee Jones
2014-02-18 14:55 ` [PATCH 30/35] mtd: st_spi_fsm: Add the ability to write to FSM's status register Lee Jones
2014-02-18 14:55 ` [PATCH 31/35] mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back Lee Jones
2014-02-18 14:55 ` [PATCH 32/35] mtd: st_spi_fsm: Supply the S25FLxxx " Lee Jones
2014-02-18 14:56 ` [PATCH 33/35] mtd: st_spi_fsm: Supply the W25Qxxx " Lee Jones
2014-02-18 14:56 ` [PATCH 34/35] mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct Lee Jones
2014-02-18 14:56 ` Lee Jones [this message]
2014-03-20 8:06 ` [PATCH v5 00/35] mtd: st_spi_fsm: Add new driver Brian Norris
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1392735362-1245-36-git-send-email-lee.jones@linaro.org \
--to=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).