linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 04/35] mtd: st_spi_fsm: Supply framework for device requests
Date: Tue, 18 Feb 2014 14:55:31 +0000	[thread overview]
Message-ID: <1392735362-1245-5-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1392735362-1245-1-git-send-email-lee.jones@linaro.org>

The FSM hardware works by setting a predetermined sequence of register
writes. Rather than open coding them inside each functional block we're
going to define them in a series of formatted 'sequence structures'.
This patch provides the framework which shall be used for every action.

Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mtd/devices/st_spi_fsm.c | 56 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index 40952f9..ac6b782 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -194,6 +194,8 @@
 
 #define STFSM_FLASH_SAFE_FREQ  10000000UL                         /* 10 MHz */
 
+#define STFSM_MAX_WAIT_SEQ_MS  1000     /* FSM execution time */
+
 struct stfsm {
 	struct device		*dev;
 	void __iomem		*base;
@@ -204,6 +206,24 @@ struct stfsm {
 	uint32_t                fifo_dir_delay;
 };
 
+struct stfsm_seq {
+	uint32_t data_size;
+	uint32_t addr1;
+	uint32_t addr2;
+	uint32_t addr_cfg;
+	uint32_t seq_opc[5];
+	uint32_t mode;
+	uint32_t dummy;
+	uint32_t status;
+	uint8_t  seq[16];
+	uint32_t seq_cfg;
+} __packed __aligned(4);
+
+static inline int stfsm_is_idle(struct stfsm *fsm)
+{
+	return readl(fsm->base + SPI_FAST_SEQ_STA) & 0x10;
+}
+
 static inline uint32_t stfsm_fifo_available(struct stfsm *fsm)
 {
 	return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f;
@@ -225,6 +245,42 @@ static void stfsm_clear_fifo(struct stfsm *fsm)
 	}
 }
 
+static inline void stfsm_load_seq(struct stfsm *fsm,
+				  const struct stfsm_seq *seq)
+{
+	void __iomem *dst = fsm->base + SPI_FAST_SEQ_TRANSFER_SIZE;
+	const uint32_t *src = (const uint32_t *)seq;
+	int words = sizeof(*seq) / sizeof(*src);
+
+	BUG_ON(!stfsm_is_idle(fsm));
+
+	while (words--) {
+		writel(*src, dst);
+		src++;
+		dst += 4;
+	}
+}
+
+static void stfsm_wait_seq(struct stfsm *fsm)
+{
+	unsigned long deadline;
+	int timeout = 0;
+
+	deadline = jiffies + msecs_to_jiffies(STFSM_MAX_WAIT_SEQ_MS);
+
+	while (!timeout) {
+		if (time_after_eq(jiffies, deadline))
+			timeout = 1;
+
+		if (stfsm_is_idle(fsm))
+			return;
+
+		cond_resched();
+	}
+
+	dev_err(fsm->dev, "timeout on sequence completion\n");
+}
+
 static int stfsm_set_mode(struct stfsm *fsm, uint32_t mode)
 {
 	int ret, timeout = 10;
-- 
1.8.3.2

  parent reply	other threads:[~2014-02-18 14:55 UTC|newest]

Thread overview: 43+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-02-18 14:55 [PATCH v5 00/35] mtd: st_spi_fsm: Add new driver Lee Jones
2014-02-18 14:55 ` [PATCH 01/35] mtd: st_spi_fsm: Allocate resources and register with MTD framework Lee Jones
2014-03-09  5:33   ` Brian Norris
2014-03-11  8:23     ` [PATCH v6 " Lee Jones
2014-03-20  7:10       ` Brian Norris
2014-02-18 14:55 ` [PATCH 02/35] mtd: st_spi_fsm: Supply all register address and bit logic defines Lee Jones
2014-02-18 14:55 ` [PATCH 03/35] mtd: st_spi_fsm: Initialise and configure the FSM for normal working conditions Lee Jones
2014-02-18 14:55 ` Lee Jones [this message]
2014-02-18 14:55 ` [PATCH 05/35] mtd: st_spi_fsm: Supply a method to read from the FSM's FIFO Lee Jones
2014-02-18 14:55 ` [PATCH 06/35] mtd: st_spi_fsm: Add support for JEDEC ID extraction Lee Jones
2014-02-18 14:55 ` [PATCH 07/35] mtd: devices: Provide header for shared OPCODEs and SFDP commands Lee Jones
2014-02-18 14:55 ` [PATCH 08/35] mtd: st_spi_fsm: Provide device look-up table Lee Jones
2014-02-18 14:55 ` [PATCH 09/35] mtd: st_spi_fsm: Dynamically setup flash device based on JEDEC ID Lee Jones
2014-02-18 14:55 ` [PATCH 10/35] mtd: st_spi_fsm: Search for preferred FSM message sequence configurations Lee Jones
2014-02-18 14:55 ` [PATCH 11/35] mtd: st_spi_fsm: Use device size to determine address width Lee Jones
2014-03-20  7:30   ` Brian Norris
2014-02-18 14:55 ` [PATCH 12/35] mtd: st_spi_fsm: Prepare the read/write FSM message sequence(s) Lee Jones
2014-02-18 14:55 ` [PATCH 13/35] mtd: st_spi_fsm: Add device-tree binding documentation Lee Jones
2014-02-18 14:55 ` [PATCH 14/35] mtd: st_spi_fsm: Fetch boot-device from mode pins Lee Jones
2014-02-18 14:55 ` [PATCH 15/35] mtd: st_spi_fsm: Provide the erase one sector sequence Lee Jones
2014-02-18 14:55 ` [PATCH 16/35] mtd: st_spi_fsm: Provide the sequence for enabling 32bit addressing mode Lee Jones
2014-02-18 14:55 ` [PATCH 17/35] mtd: st_spi_fsm: Prepare read/write sequences according to configuration Lee Jones
2014-02-18 14:55 ` [PATCH 18/35] mtd: st_spi_fsm: Add a check to if the chip can handle an SoC reset Lee Jones
2014-02-18 14:55 ` [PATCH 19/35] mtd: st_spi_fsm: Provide a method to put the chip into 32bit addressing mode Lee Jones
2014-02-18 14:55 ` [PATCH 20/35] mtd: st_spi_fsm: Update the flash Volatile Configuration Register Lee Jones
2014-02-18 14:55 ` [PATCH 21/35] mtd: st_spi_fsm: Provide the default read/write configurations Lee Jones
2014-02-18 14:55 ` [PATCH 22/35] mtd: st_spi_fsm: Supply the N25Qxxx specific read configurations Lee Jones
2014-02-18 14:55 ` [PATCH 23/35] mtd: st_spi_fsm: Supply the N25Qxxx chip specific configuration call-back Lee Jones
2014-02-18 14:55 ` [PATCH 24/35] mtd: st_spi_fsm: Prepare default sequences for read/write/erase Lee Jones
2014-02-18 14:55 ` [PATCH 25/35] mtd: st_spi_fsm: Add the ability to read from a Serial Flash device Lee Jones
2014-03-20  7:55   ` Brian Norris
2014-02-18 14:55 ` [PATCH 26/35] mtd: st_spi_fsm: Write to Flash via the FSM FIFO Lee Jones
2014-02-18 14:55 ` [PATCH 27/35] mtd: st_spi_fsm: Supply a busy wait for post-write status Lee Jones
2014-03-20  7:27   ` Brian Norris
2014-02-18 14:55 ` [PATCH 28/35] mtd: st_spi_fsm: Erase partly or as a whole a Serial Flash device Lee Jones
2014-02-18 14:55 ` [PATCH 29/35] mtd: st_spi_fsm: Add the ability to read the FSM's status Lee Jones
2014-02-18 14:55 ` [PATCH 30/35] mtd: st_spi_fsm: Add the ability to write to FSM's status register Lee Jones
2014-02-18 14:55 ` [PATCH 31/35] mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back Lee Jones
2014-02-18 14:55 ` [PATCH 32/35] mtd: st_spi_fsm: Supply the S25FLxxx " Lee Jones
2014-02-18 14:56 ` [PATCH 33/35] mtd: st_spi_fsm: Supply the W25Qxxx " Lee Jones
2014-02-18 14:56 ` [PATCH 34/35] mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct Lee Jones
2014-02-18 14:56 ` [PATCH 35/35] ARM: STi: Add support for the FSM Serial Flash Controller Lee Jones
2014-03-20  8:06 ` [PATCH v5 00/35] mtd: st_spi_fsm: Add new driver Brian Norris

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1392735362-1245-5-git-send-email-lee.jones@linaro.org \
    --to=lee.jones@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).