* [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes
@ 2014-02-19 20:02 klightspeed at killerwolves.net
2014-02-19 20:02 ` [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology klightspeed at killerwolves.net
` (5 more replies)
0 siblings, 6 replies; 11+ messages in thread
From: klightspeed at killerwolves.net @ 2014-02-19 20:02 UTC (permalink / raw)
To: linux-arm-kernel
This patchset adds support for around 30 kirkwood bases Synology NAS
boxes. Patch #1 documents vendor prefixes. Patch #2 generalizes the qnap
power off driver so that it can also be used for Synology devices.
Patch #3 adds sii,s35390a to i2c trivial devices. Patch #4 adds the
synology DT files.
v2:
Typo fix in qnap-poweroff.c
Use ricoy stock ticker instead of ricoh
Describe the lego structure of the hardware
v3:
Merge synology dtsi files into a single dtsi file
v4:
Various minor fixes to synology dtsi file
v5:
Fix typos in commit messages
Remove unnecessary casts in qnap-poweroff.c
v6:
Revert qnap vendor prefix change from v5
v7:
Revert ricoh vendor prefix change from v2
Andrew Lunn (3):
DT: Vendor prefixes: Add ricoh, qnap, sii and synology
Power: Reset: Generalize qnap-poweroff to with on Synology devices.
DT: i2c: Trivial: Add sii,s35390a
Ben Peddell (1):
ARM: Kirkwood: Add support for many Synology NAS devices
.../devicetree/bindings/i2c/trivial-devices.txt | 1 +
.../bindings/power_supply/qnap-poweroff.txt | 5 +-
.../devicetree/bindings/vendor-prefixes.txt | 4 +
arch/arm/boot/dts/Makefile | 15 +
arch/arm/boot/dts/kirkwood-ds109.dts | 41 +
arch/arm/boot/dts/kirkwood-ds110jv10.dts | 41 +
arch/arm/boot/dts/kirkwood-ds111.dts | 44 ++
arch/arm/boot/dts/kirkwood-ds112.dts | 48 ++
arch/arm/boot/dts/kirkwood-ds209.dts | 44 ++
arch/arm/boot/dts/kirkwood-ds210.dts | 46 ++
arch/arm/boot/dts/kirkwood-ds212.dts | 47 ++
arch/arm/boot/dts/kirkwood-ds212j.dts | 41 +
arch/arm/boot/dts/kirkwood-ds409.dts | 48 ++
arch/arm/boot/dts/kirkwood-ds409slim.dts | 40 +
arch/arm/boot/dts/kirkwood-ds411.dts | 52 ++
arch/arm/boot/dts/kirkwood-ds411j.dts | 48 ++
arch/arm/boot/dts/kirkwood-ds411slim.dts | 48 ++
arch/arm/boot/dts/kirkwood-rs212.dts | 48 ++
arch/arm/boot/dts/kirkwood-rs409.dts | 44 ++
arch/arm/boot/dts/kirkwood-rs411.dts | 44 ++
arch/arm/boot/dts/kirkwood-synology.dtsi | 871 +++++++++++++++++++++
drivers/power/reset/qnap-poweroff.c | 49 +-
22 files changed, 1656 insertions(+), 13 deletions(-)
create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts
create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts
create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts
create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts
create mode 100644 arch/arm/boot/dts/kirkwood-synology.dtsi
--
1.8.3.2
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net @ 2014-02-19 20:02 ` klightspeed at killerwolves.net 2014-02-19 21:17 ` Rob Herring 2014-02-19 20:02 ` [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices klightspeed at killerwolves.net ` (4 subsequent siblings) 5 siblings, 1 reply; 11+ messages in thread From: klightspeed at killerwolves.net @ 2014-02-19 20:02 UTC (permalink / raw) To: linux-arm-kernel From: Andrew Lunn <andrew@lunn.ch> The following patches make use of vendor names: * ricoh (Ricoh Co. Ltd.); * qnap (QNAP Systems, Inc.); * sii (Seiko Instruments, Inc.); and * synology (Synology, Inc.) Add them to the vendor prefix list. Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jason Cooper <jason@lakedaemon.net> --- v2: Use stock ticker for Ricoh as vendor name s/Richoh/Ricoh/ v5: Add vendor prefix for QNAP v6: Revert qnap vendor prefix change from v5 Now properly based on -rc1 v7: Revert ricoh vendor prefix change from v2 --- Documentation/devicetree/bindings/vendor-prefixes.txt | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 3f900cd..4a52fa9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -65,10 +65,12 @@ picochip Picochip Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm, Inc. +qnap QNAP Systems, Inc. ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation +ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor sbs Smart Battery System @@ -76,11 +78,13 @@ schindler Schindler sil Silicon Image silabs Silicon Laboratories simtek +sii Seiko Instruments, Inc. sirf SiRF Technology, Inc. snps Synopsys, Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson +synology Synology, Inc. ti Texas Instruments tlm Trusted Logic Mobility toshiba Toshiba Corporation -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology 2014-02-19 20:02 ` [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology klightspeed at killerwolves.net @ 2014-02-19 21:17 ` Rob Herring 0 siblings, 0 replies; 11+ messages in thread From: Rob Herring @ 2014-02-19 21:17 UTC (permalink / raw) To: linux-arm-kernel On Wed, Feb 19, 2014 at 2:02 PM, <klightspeed@killerwolves.net> wrote: > From: Andrew Lunn <andrew@lunn.ch> > > The following patches make use of vendor names: > * ricoh (Ricoh Co. Ltd.); > * qnap (QNAP Systems, Inc.); > * sii (Seiko Instruments, Inc.); and > * synology (Synology, Inc.) > > Add them to the vendor prefix list. > > Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> > Signed-off-by: Andrew Lunn <andrew@lunn.ch> > Acked-by: Jason Cooper <jason@lakedaemon.net> Acked-by: Rob Herring <robh@kernel.org> > --- > v2: > Use stock ticker for Ricoh as vendor name > s/Richoh/Ricoh/ > > v5: > Add vendor prefix for QNAP > > v6: > Revert qnap vendor prefix change from v5 > Now properly based on -rc1 > > v7: > Revert ricoh vendor prefix change from v2 > > --- > Documentation/devicetree/bindings/vendor-prefixes.txt | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt > index 3f900cd..4a52fa9 100644 > --- a/Documentation/devicetree/bindings/vendor-prefixes.txt > +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt > @@ -65,10 +65,12 @@ picochip Picochip Ltd > powervr PowerVR (deprecated, use img) > qca Qualcomm Atheros, Inc. > qcom Qualcomm, Inc. > +qnap QNAP Systems, Inc. > ralink Mediatek/Ralink Technology Corp. > ramtron Ramtron International > realtek Realtek Semiconductor Corp. > renesas Renesas Electronics Corporation > +ricoh Ricoh Co. Ltd. > rockchip Fuzhou Rockchip Electronics Co., Ltd > samsung Samsung Semiconductor > sbs Smart Battery System > @@ -76,11 +78,13 @@ schindler Schindler > sil Silicon Image > silabs Silicon Laboratories > simtek > +sii Seiko Instruments, Inc. > sirf SiRF Technology, Inc. > snps Synopsys, Inc. > st STMicroelectronics > ste ST-Ericsson > stericsson ST-Ericsson > +synology Synology, Inc. > ti Texas Instruments > tlm Trusted Logic Mobility > toshiba Toshiba Corporation > -- > 1.8.3.2 > ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices. 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net 2014-02-19 20:02 ` [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology klightspeed at killerwolves.net @ 2014-02-19 20:02 ` klightspeed at killerwolves.net 2014-02-22 1:39 ` Jason Cooper 2014-02-19 20:02 ` [PATCH v7 3/4] DT: i2c: Trivial: Add sii,s35390a klightspeed at killerwolves.net ` (3 subsequent siblings) 5 siblings, 1 reply; 11+ messages in thread From: klightspeed at killerwolves.net @ 2014-02-19 20:02 UTC (permalink / raw) To: linux-arm-kernel From: Andrew Lunn <andrew@lunn.ch> The Synology NAS devices use a very similar mechanism to QNAP NAS devices to power off. Both send a single charactor command to a PIC, over the second serial port. However the baud rate and the command differ. Generalize the driver to support this. Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jason Cooper <jason@lakedaemon.net> Cc: Anton Vorontsov <anton@enomsg.org> Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> --- .../bindings/power_supply/qnap-poweroff.txt | 5 ++- drivers/power/reset/qnap-poweroff.c | 49 ++++++++++++++++------ 2 files changed, 41 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt index 0347d83..af25e77 100644 --- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt +++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt @@ -6,8 +6,11 @@ Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the microcontroller to turn the power off. This driver adds a handler to pm_power_off which is called to turn the power off. +Synology NAS devices use a similar scheme, but a different baud rate, +9600, and a different character, '1'. + Required Properties: -- compatible: Should be "qnap,power-off" +- compatible: Should be "qnap,power-off" or "synology,power-off" - reg: Address and length of the register set for UART1 - clocks: tclk clock diff --git a/drivers/power/reset/qnap-poweroff.c b/drivers/power/reset/qnap-poweroff.c index 37f56f7..a75db7f 100644 --- a/drivers/power/reset/qnap-poweroff.c +++ b/drivers/power/reset/qnap-poweroff.c @@ -1,5 +1,5 @@ /* - * QNAP Turbo NAS Board power off + * QNAP Turbo NAS Board power off. Can also be used on Synology devices. * * Copyright (C) 2012 Andrew Lunn <andrew@lunn.ch> * @@ -25,17 +25,43 @@ #define UART1_REG(x) (base + ((UART_##x) << 2)) +struct power_off_cfg { + u32 baud; + char cmd; +}; + +static const struct power_off_cfg qnap_power_off_cfg = { + .baud = 19200, + .cmd = 'A', +}; + +static const struct power_off_cfg synology_power_off_cfg = { + .baud = 9600, + .cmd = '1', +}; + +static const struct of_device_id qnap_power_off_of_match_table[] = { + { .compatible = "qnap,power-off", + .data = &qnap_power_off_cfg, + }, + { .compatible = "synology,power-off", + .data = &synology_power_off_cfg, + }, + {} +}; +MODULE_DEVICE_TABLE(of, qnap_power_off_of_match_table); + static void __iomem *base; static unsigned long tclk; +static const struct power_off_cfg *cfg; static void qnap_power_off(void) { - /* 19200 baud divisor */ - const unsigned divisor = ((tclk + (8 * 19200)) / (16 * 19200)); + const unsigned divisor = ((tclk + (8 * cfg->baud)) / (16 * cfg->baud)); pr_err("%s: triggering power-off...\n", __func__); - /* hijack UART1 and reset into sane state (19200,8n1) */ + /* hijack UART1 and reset into sane state */ writel(0x83, UART1_REG(LCR)); writel(divisor & 0xff, UART1_REG(DLL)); writel((divisor >> 8) & 0xff, UART1_REG(DLM)); @@ -44,16 +70,21 @@ static void qnap_power_off(void) writel(0x00, UART1_REG(FCR)); writel(0x00, UART1_REG(MCR)); - /* send the power-off command 'A' to PIC */ - writel('A', UART1_REG(TX)); + /* send the power-off command to PIC */ + writel(cfg->cmd, UART1_REG(TX)); } static int qnap_power_off_probe(struct platform_device *pdev) { + struct device_node *np = pdev->dev.of_node; struct resource *res; struct clk *clk; char symname[KSYM_NAME_LEN]; + const struct of_device_id *match = + of_match_node(qnap_power_off_of_match_table, np); + cfg = match->data; + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!res) { dev_err(&pdev->dev, "Missing resource"); @@ -94,12 +125,6 @@ static int qnap_power_off_remove(struct platform_device *pdev) return 0; } -static const struct of_device_id qnap_power_off_of_match_table[] = { - { .compatible = "qnap,power-off", }, - {} -}; -MODULE_DEVICE_TABLE(of, qnap_power_off_of_match_table); - static struct platform_driver qnap_power_off_driver = { .probe = qnap_power_off_probe, .remove = qnap_power_off_remove, -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices. 2014-02-19 20:02 ` [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices klightspeed at killerwolves.net @ 2014-02-22 1:39 ` Jason Cooper 2014-03-04 3:54 ` Jason Cooper 0 siblings, 1 reply; 11+ messages in thread From: Jason Cooper @ 2014-02-22 1:39 UTC (permalink / raw) To: linux-arm-kernel Dmitry, David, On Thu, Feb 20, 2014 at 06:02:35AM +1000, klightspeed at killerwolves.net wrote: > From: Andrew Lunn <andrew@lunn.ch> > > The Synology NAS devices use a very similar mechanism to QNAP NAS > devices to power off. Both send a single charactor command to a PIC, > over the second serial port. However the baud rate and the command > differ. Generalize the driver to support this. > > Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> > Signed-off-by: Andrew Lunn <andrew@lunn.ch> > Acked-by: Jason Cooper <jason@lakedaemon.net> > Cc: Anton Vorontsov <anton@enomsg.org> > Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> > Cc: David Woodhouse <dwmw2@infradead.org> > --- > .../bindings/power_supply/qnap-poweroff.txt | 5 ++- > drivers/power/reset/qnap-poweroff.c | 49 ++++++++++++++++------ > 2 files changed, 41 insertions(+), 13 deletions(-) Do you guys want to take this, or me? I'm fine either way, there's no dependencies. thx, Jason. > diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt > index 0347d83..af25e77 100644 > --- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt > +++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt > @@ -6,8 +6,11 @@ Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the > microcontroller to turn the power off. This driver adds a handler to > pm_power_off which is called to turn the power off. > > +Synology NAS devices use a similar scheme, but a different baud rate, > +9600, and a different character, '1'. > + > Required Properties: > -- compatible: Should be "qnap,power-off" > +- compatible: Should be "qnap,power-off" or "synology,power-off" > > - reg: Address and length of the register set for UART1 > - clocks: tclk clock > diff --git a/drivers/power/reset/qnap-poweroff.c b/drivers/power/reset/qnap-poweroff.c > index 37f56f7..a75db7f 100644 > --- a/drivers/power/reset/qnap-poweroff.c > +++ b/drivers/power/reset/qnap-poweroff.c > @@ -1,5 +1,5 @@ > /* > - * QNAP Turbo NAS Board power off > + * QNAP Turbo NAS Board power off. Can also be used on Synology devices. > * > * Copyright (C) 2012 Andrew Lunn <andrew@lunn.ch> > * > @@ -25,17 +25,43 @@ > > #define UART1_REG(x) (base + ((UART_##x) << 2)) > > +struct power_off_cfg { > + u32 baud; > + char cmd; > +}; > + > +static const struct power_off_cfg qnap_power_off_cfg = { > + .baud = 19200, > + .cmd = 'A', > +}; > + > +static const struct power_off_cfg synology_power_off_cfg = { > + .baud = 9600, > + .cmd = '1', > +}; > + > +static const struct of_device_id qnap_power_off_of_match_table[] = { > + { .compatible = "qnap,power-off", > + .data = &qnap_power_off_cfg, > + }, > + { .compatible = "synology,power-off", > + .data = &synology_power_off_cfg, > + }, > + {} > +}; > +MODULE_DEVICE_TABLE(of, qnap_power_off_of_match_table); > + > static void __iomem *base; > static unsigned long tclk; > +static const struct power_off_cfg *cfg; > > static void qnap_power_off(void) > { > - /* 19200 baud divisor */ > - const unsigned divisor = ((tclk + (8 * 19200)) / (16 * 19200)); > + const unsigned divisor = ((tclk + (8 * cfg->baud)) / (16 * cfg->baud)); > > pr_err("%s: triggering power-off...\n", __func__); > > - /* hijack UART1 and reset into sane state (19200,8n1) */ > + /* hijack UART1 and reset into sane state */ > writel(0x83, UART1_REG(LCR)); > writel(divisor & 0xff, UART1_REG(DLL)); > writel((divisor >> 8) & 0xff, UART1_REG(DLM)); > @@ -44,16 +70,21 @@ static void qnap_power_off(void) > writel(0x00, UART1_REG(FCR)); > writel(0x00, UART1_REG(MCR)); > > - /* send the power-off command 'A' to PIC */ > - writel('A', UART1_REG(TX)); > + /* send the power-off command to PIC */ > + writel(cfg->cmd, UART1_REG(TX)); > } > > static int qnap_power_off_probe(struct platform_device *pdev) > { > + struct device_node *np = pdev->dev.of_node; > struct resource *res; > struct clk *clk; > char symname[KSYM_NAME_LEN]; > > + const struct of_device_id *match = > + of_match_node(qnap_power_off_of_match_table, np); > + cfg = match->data; > + > res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > if (!res) { > dev_err(&pdev->dev, "Missing resource"); > @@ -94,12 +125,6 @@ static int qnap_power_off_remove(struct platform_device *pdev) > return 0; > } > > -static const struct of_device_id qnap_power_off_of_match_table[] = { > - { .compatible = "qnap,power-off", }, > - {} > -}; > -MODULE_DEVICE_TABLE(of, qnap_power_off_of_match_table); > - > static struct platform_driver qnap_power_off_driver = { > .probe = qnap_power_off_probe, > .remove = qnap_power_off_remove, > -- > 1.8.3.2 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel at lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices. 2014-02-22 1:39 ` Jason Cooper @ 2014-03-04 3:54 ` Jason Cooper 0 siblings, 0 replies; 11+ messages in thread From: Jason Cooper @ 2014-03-04 3:54 UTC (permalink / raw) To: linux-arm-kernel On Fri, Feb 21, 2014 at 08:39:54PM -0500, Jason Cooper wrote: > Dmitry, David, > > On Thu, Feb 20, 2014 at 06:02:35AM +1000, klightspeed at killerwolves.net wrote: > > From: Andrew Lunn <andrew@lunn.ch> > > > > The Synology NAS devices use a very similar mechanism to QNAP NAS > > devices to power off. Both send a single charactor command to a PIC, > > over the second serial port. However the baud rate and the command > > differ. Generalize the driver to support this. > > > > Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> > > Signed-off-by: Andrew Lunn <andrew@lunn.ch> > > Acked-by: Jason Cooper <jason@lakedaemon.net> > > Cc: Anton Vorontsov <anton@enomsg.org> > > Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> > > Cc: David Woodhouse <dwmw2@infradead.org> > > --- > > .../bindings/power_supply/qnap-poweroff.txt | 5 ++- > > drivers/power/reset/qnap-poweroff.c | 49 ++++++++++++++++------ > > 2 files changed, 41 insertions(+), 13 deletions(-) > > Do you guys want to take this, or me? I'm fine either way, there's no > dependencies. Hmmm, it's been over a week. Since it's isolated to a driver only kirkwood/mvebu devices use, I'll go ahead a queue this up to go through mvebu/arm-soc for v3.15. Please ping me in the next few days if you'd prefer I drop it. Applied to mvebu/drivers thx, Jason. > > diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt > > index 0347d83..af25e77 100644 > > --- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt > > +++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt > > @@ -6,8 +6,11 @@ Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the > > microcontroller to turn the power off. This driver adds a handler to > > pm_power_off which is called to turn the power off. > > > > +Synology NAS devices use a similar scheme, but a different baud rate, > > +9600, and a different character, '1'. > > + > > Required Properties: > > -- compatible: Should be "qnap,power-off" > > +- compatible: Should be "qnap,power-off" or "synology,power-off" > > > > - reg: Address and length of the register set for UART1 > > - clocks: tclk clock > > diff --git a/drivers/power/reset/qnap-poweroff.c b/drivers/power/reset/qnap-poweroff.c > > index 37f56f7..a75db7f 100644 > > --- a/drivers/power/reset/qnap-poweroff.c > > +++ b/drivers/power/reset/qnap-poweroff.c > > @@ -1,5 +1,5 @@ > > /* > > - * QNAP Turbo NAS Board power off > > + * QNAP Turbo NAS Board power off. Can also be used on Synology devices. > > * > > * Copyright (C) 2012 Andrew Lunn <andrew@lunn.ch> > > * > > @@ -25,17 +25,43 @@ > > > > #define UART1_REG(x) (base + ((UART_##x) << 2)) > > > > +struct power_off_cfg { > > + u32 baud; > > + char cmd; > > +}; > > + > > +static const struct power_off_cfg qnap_power_off_cfg = { > > + .baud = 19200, > > + .cmd = 'A', > > +}; > > + > > +static const struct power_off_cfg synology_power_off_cfg = { > > + .baud = 9600, > > + .cmd = '1', > > +}; > > + > > +static const struct of_device_id qnap_power_off_of_match_table[] = { > > + { .compatible = "qnap,power-off", > > + .data = &qnap_power_off_cfg, > > + }, > > + { .compatible = "synology,power-off", > > + .data = &synology_power_off_cfg, > > + }, > > + {} > > +}; > > +MODULE_DEVICE_TABLE(of, qnap_power_off_of_match_table); > > + > > static void __iomem *base; > > static unsigned long tclk; > > +static const struct power_off_cfg *cfg; > > > > static void qnap_power_off(void) > > { > > - /* 19200 baud divisor */ > > - const unsigned divisor = ((tclk + (8 * 19200)) / (16 * 19200)); > > + const unsigned divisor = ((tclk + (8 * cfg->baud)) / (16 * cfg->baud)); > > > > pr_err("%s: triggering power-off...\n", __func__); > > > > - /* hijack UART1 and reset into sane state (19200,8n1) */ > > + /* hijack UART1 and reset into sane state */ > > writel(0x83, UART1_REG(LCR)); > > writel(divisor & 0xff, UART1_REG(DLL)); > > writel((divisor >> 8) & 0xff, UART1_REG(DLM)); > > @@ -44,16 +70,21 @@ static void qnap_power_off(void) > > writel(0x00, UART1_REG(FCR)); > > writel(0x00, UART1_REG(MCR)); > > > > - /* send the power-off command 'A' to PIC */ > > - writel('A', UART1_REG(TX)); > > + /* send the power-off command to PIC */ > > + writel(cfg->cmd, UART1_REG(TX)); > > } > > > > static int qnap_power_off_probe(struct platform_device *pdev) > > { > > + struct device_node *np = pdev->dev.of_node; > > struct resource *res; > > struct clk *clk; > > char symname[KSYM_NAME_LEN]; > > > > + const struct of_device_id *match = > > + of_match_node(qnap_power_off_of_match_table, np); > > + cfg = match->data; > > + > > res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > if (!res) { > > dev_err(&pdev->dev, "Missing resource"); > > @@ -94,12 +125,6 @@ static int qnap_power_off_remove(struct platform_device *pdev) > > return 0; > > } > > > > -static const struct of_device_id qnap_power_off_of_match_table[] = { > > - { .compatible = "qnap,power-off", }, > > - {} > > -}; > > -MODULE_DEVICE_TABLE(of, qnap_power_off_of_match_table); > > - > > static struct platform_driver qnap_power_off_driver = { > > .probe = qnap_power_off_probe, > > .remove = qnap_power_off_remove, > > -- > > 1.8.3.2 > > > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel at lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo at vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v7 3/4] DT: i2c: Trivial: Add sii,s35390a 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net 2014-02-19 20:02 ` [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology klightspeed at killerwolves.net 2014-02-19 20:02 ` [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices klightspeed at killerwolves.net @ 2014-02-19 20:02 ` klightspeed at killerwolves.net 2014-02-19 20:02 ` [PATCH v7 4/4] ARM: Kirkwood: Add support for many Synology NAS devices klightspeed at killerwolves.net ` (2 subsequent siblings) 5 siblings, 0 replies; 11+ messages in thread From: klightspeed at killerwolves.net @ 2014-02-19 20:02 UTC (permalink / raw) To: linux-arm-kernel From: Andrew Lunn <andrew@lunn.ch> Add the Seiko Instruments Inc S35390a to the list of trivial i2c devices. Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jason Cooper <jason@lakedaemon.net> --- Documentation/devicetree/bindings/i2c/trivial-devices.txt | 1 + 1 file changed, 1 insertions(+) diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 1a1ac2e..5f37191 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -58,6 +58,7 @@ plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch ramtron,24c64 i2c serial eeprom (24cxx) ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sii,s35390a 2-wire CMOS real-time clock st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v7 4/4] ARM: Kirkwood: Add support for many Synology NAS devices 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net ` (2 preceding siblings ...) 2014-02-19 20:02 ` [PATCH v7 3/4] DT: i2c: Trivial: Add sii,s35390a klightspeed at killerwolves.net @ 2014-02-19 20:02 ` klightspeed at killerwolves.net 2014-02-20 9:11 ` Andrew Lunn 2014-02-20 9:18 ` [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes Andrew Lunn 2014-02-22 1:56 ` Jason Cooper 5 siblings, 1 reply; 11+ messages in thread From: klightspeed at killerwolves.net @ 2014-02-19 20:02 UTC (permalink / raw) To: linux-arm-kernel From: "Ben Peddell" <klightspeed@killerwolves.net> Add device tree fragments and files to support many of the kirkwood based Synology NAS devices. This is a modification of Andrew Lunn's <andrew@lunn.ch> translation of the board setup file maintained by Ben Peddell <klightspeed@killerwolves.net> The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units. All other Synology Kirkwood-based DiskStations and RackStations use the Seiko S35390A RTC. Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed with the built-in SATA interface activity/presence pins on mpp 20-23, while the 4-bay units use ge01 and a PCIe SATA controller, and put the software controlled HDD leds on mpp 36-43. Most of the 6281 units with HDD power controls use mpp 29 and 31, while most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45 and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and most 4-bay units didn't have a separate power control for HDD1. These power controls are presumably to limit startup current from the 12V brick power supply. Instead of using separate dtsi files in a synology directory, this patch uses a single dtsi file containing all of the modules for these boards, with all of the modules not common to all boards disabled. The board dts files then enable the appropriate modules for their boards. Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j) --- v2: Fix gpio's which should be gpo. Rebase onto v3-14-rc1 Update RTC nodes with vendor name. Update SPI flash node with vendor name. Add a description of the lego Use ricoy, i.e. the stock ticker v3: Merge Synology dtsi files into single dtsi file v4: Various minor fixes to synology dtsi file v7: Revert ricoh vendor prefix change from v2 --- arch/arm/boot/dts/Makefile | 15 + arch/arm/boot/dts/kirkwood-ds109.dts | 41 ++ arch/arm/boot/dts/kirkwood-ds110jv10.dts | 41 ++ arch/arm/boot/dts/kirkwood-ds111.dts | 44 ++ arch/arm/boot/dts/kirkwood-ds112.dts | 48 ++ arch/arm/boot/dts/kirkwood-ds209.dts | 44 ++ arch/arm/boot/dts/kirkwood-ds210.dts | 46 ++ arch/arm/boot/dts/kirkwood-ds212.dts | 47 ++ arch/arm/boot/dts/kirkwood-ds212j.dts | 41 ++ arch/arm/boot/dts/kirkwood-ds409.dts | 48 ++ arch/arm/boot/dts/kirkwood-ds409slim.dts | 40 ++ arch/arm/boot/dts/kirkwood-ds411.dts | 52 ++ arch/arm/boot/dts/kirkwood-ds411j.dts | 48 ++ arch/arm/boot/dts/kirkwood-ds411slim.dts | 48 ++ arch/arm/boot/dts/kirkwood-rs212.dts | 48 ++ arch/arm/boot/dts/kirkwood-rs409.dts | 44 ++ arch/arm/boot/dts/kirkwood-rs411.dts | 44 ++ arch/arm/boot/dts/kirkwood-synology.dtsi | 871 +++++++++++++++++++++++++++++++ 18 files changed, 1610 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts create mode 100644 arch/arm/boot/dts/kirkwood-synology.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 6d1e43d..e286abc 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -90,6 +90,18 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-dns325.dtb \ kirkwood-dockstar.dtb \ kirkwood-dreamplug.dtb \ + kirkwood-ds109.dtb \ + kirkwood-ds110jv10.dtb \ + kirkwood-ds111.dtb \ + kirkwood-ds209.dtb \ + kirkwood-ds210.dtb \ + kirkwood-ds212.dtb \ + kirkwood-ds212j.dtb \ + kirkwood-ds409.dtb \ + kirkwood-ds409slim.dtb \ + kirkwood-ds411.dtb \ + kirkwood-ds411j.dtb \ + kirkwood-ds411slim.dtb \ kirkwood-goflexnet.dtb \ kirkwood-guruplug-server-plus.dtb \ kirkwood-ib62x0.dtb \ @@ -112,6 +124,9 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-nsa310a.dtb \ kirkwood-openblocks_a6.dtb \ kirkwood-openblocks_a7.dtb \ + kirkwood-rs212.dtb \ + kirkwood-rs409.dtb \ + kirkwood-rs411.dtb \ kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug-esata.dtb \ kirkwood-topkick.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts new file mode 100644 index 0000000..772092c --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds109.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS109, DS110, DS110jv20"; + compatible = "synology,ds109", "synology,ds110jv20", + "synology,ds110", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts new file mode 100644 index 0000000..aabafbe --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS110j v10 and v30"; + compatible = "synology,ds110jv10", "synology,ds110jv30", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts new file mode 100644 index 0000000..16ec7fb --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds111.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS111"; + compatible = "synology,ds111", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts new file mode 100644 index 0000000..cff1b23 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds112.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS111"; + compatible = "synology,ds111", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-21-2 { + status = "okay"; + }; + + regulators-hdd-30 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts new file mode 100644 index 0000000..3304119 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds209.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS209"; + compatible = "synology,ds209", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; + + regulators-hdd-31 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts new file mode 100644 index 0000000..6052eaa --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds210.dts @@ -0,0 +1,46 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS210 v10, v20, v30, DS211j"; + compatible = "synology,ds210jv10", "synology,ds210jv20", + "synology,ds210jv30", "synology,ds211j", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; + + regulators-hdd-31 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts new file mode 100644 index 0000000..7f76cd3 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds212.dts @@ -0,0 +1,47 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10"; + compatible = "synology,ds212", "synology,ds212pv10", + "synology,ds212pv10", "synology,ds212pv20", + "synology,ds213airv10", "synology,ds213v10", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts new file mode 100644 index 0000000..1f83a00 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS212j v10, v20"; + compatible = "synology,ds212jv10", "synology,ds212jv20", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts new file mode 100644 index 0000000..0a573ad --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds409.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS409, DS410j"; + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + gpio-leds-alarm-12 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts new file mode 100644 index 0000000..1848a62 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts @@ -0,0 +1,40 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology 409slim"; + compatible = "synology,ds409slim", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-20 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts new file mode 100644 index 0000000..a1737b4 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411.dts @@ -0,0 +1,52 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411, DS413jv10"; + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + regulators-hdd-34 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts new file mode 100644 index 0000000..0cde914 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411j"; + compatible = "synology,ds411j", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + gpio-leds-alarm-12 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts new file mode 100644 index 0000000..aef0cad --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411slim"; + compatible = "synology,ds411slim", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts new file mode 100644 index 0000000..93ec3d0 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs212.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS212"; + compatible = "synology,rs212", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-3 { + status = "okay"; + }; + + gpio-leds-hdd-38 { + status = "okay"; + }; + + regulators-hdd-30-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts new file mode 100644 index 0000000..311df4e --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs409.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS409"; + compatible = "synology,rs409", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts new file mode 100644 index 0000000..f90da85 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs411.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS411 RS812"; + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-3 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/kirkwood-synology.dtsi new file mode 100644 index 0000000..92b3177 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-synology.dtsi @@ -0,0 +1,871 @@ +/* + * Nodes for Marvell 628x Synology devices + * + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/ { + mbus { + pcie-controller { + status = "okay"; + + pcie at 1,0 { + status = "okay"; + }; + + pcie2: pcie at 2,0 { + status = "disabled"; + }; + }; + }; + + ocp at f1000000 { + pinctrl: pinctrl at 10000 { + pmx_alarmled_12: pmx-alarmled-12 { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_15: pmx-fanctrl-15 { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_16: pmx-fanctrl-16 { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_17: pmx-fanctrl-17 { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_18: pmx-fanalarm-18 { + marvell,pins = "mpp18"; + marvell,function = "gpo"; + }; + + pmx_hddled_20: pmx-hddled-20 { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + + pmx_hddled_21: pmx-hddled-21 { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_hddled_22: pmx-hddled-22 { + marvell,pins = "mpp22"; + marvell,function = "gpio"; + }; + + pmx_hddled_23: pmx-hddled-23 { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + + pmx_hddled_24: pmx-hddled-24 { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + + pmx_hddled_25: pmx-hddled-25 { + marvell,pins = "mpp25"; + marvell,function = "gpio"; + }; + + pmx_hddled_26: pmx-hddled-26 { + marvell,pins = "mpp26"; + marvell,function = "gpio"; + }; + + pmx_hddled_27: pmx-hddled-27 { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + pmx_hddled_28: pmx-hddled-28 { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 { + marvell,pins = "mpp30"; + marvell,function = "gpio"; + }; + + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_32: pmx-fanctrl-32 { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_33: pmx-fanctrl-33 { + marvell,pins = "mpp33"; + marvell,function = "gpo"; + }; + + pmx_fanctrl_34: pmx-fanctrl-34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_35: pmx-fanalarm-35 { + marvell,pins = "mpp35"; + marvell,function = "gpio"; + }; + + pmx_hddled_36: pmx-hddled-36 { + marvell,pins = "mpp36"; + marvell,function = "gpio"; + }; + + pmx_hddled_37: pmx-hddled-37 { + marvell,pins = "mpp37"; + marvell,function = "gpio"; + }; + + pmx_hddled_38: pmx-hddled-38 { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; + + pmx_hddled_39: pmx-hddled-39 { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + + pmx_hddled_40: pmx-hddled-40 { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + pmx_hddled_41: pmx-hddled-41 { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_hddled_42: pmx-hddled-42 { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + pmx_hddled_43: pmx-hddled-43 { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + pmx_hddled_44: pmx-hddled-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_hddled_45: pmx-hddled-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_44: pmx-fanalarm-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_45: pmx-fanalarm-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + }; + + rtc at 10300 { + status = "disabled"; + }; + + spi at 10600 { + status = "okay"; + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + + m25p80 at 0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + reg = <0>; + spi-max-frequency = <20000000>; + mode = <0>; + + partition at 00000000 { + reg = <0x00000000 0x00080000>; + label = "RedBoot"; + }; + + partition at 00080000 { + reg = <0x00080000 0x00200000>; + label = "zImage"; + }; + + partition at 00280000 { + reg = <0x00280000 0x00140000>; + label = "rd.gz"; + }; + + partition at 003c0000 { + reg = <0x003c0000 0x00010000>; + label = "vendor"; + }; + + partition at 003d0000 { + reg = <0x003d0000 0x00020000>; + label = "RedBoot config"; + }; + + partition at 003f0000 { + reg = <0x003f0000 0x00010000>; + label = "FIS directory"; + }; + }; + }; + + i2c at 11000 { + status = "okay"; + clock-frequency = <400000>; + pinctrl-0 = <&pmx_twsi0>; + pinctrl-names = "default"; + + rs5c372: rs5c372 at 32 { + status = "disabled"; + compatible = "ricoh,rs5c372"; + reg = <0x32>; + }; + + s35390a: s35390a at 30 { + status = "disabled"; + compatible = "ssi,s35390a"; + reg = <0x30>; + }; + }; + + serial at 12000 { + status = "okay"; + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + }; + + serial at 12100 { + status = "okay"; + pinctrl-0 = <&pmx_uart1>; + pinctrl-names = "default"; + }; + + poweroff at 12100 { + compatible = "synology,power-off"; + reg = <0x12100 0x100>; + clocks = <&gate_clk 7>; + }; + + sata at 80000 { + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; + pinctrl-names = "default"; + status = "okay"; + nr-ports = <2>; + }; + }; + + gpio-fan-150-32-35 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH + &gpio1 1 GPIO_ACTIVE_HIGH + &gpio1 2 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2200 1 + 2500 2 + 3000 4 + 3300 3 + 3700 5 + 3800 6 + 4200 7 >; + }; + + gpio-fan-150-15-18 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_18>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2200 1 + 2500 2 + 3000 4 + 3300 3 + 3700 5 + 3800 6 + 4200 7 >; + }; + + gpio-fan-100-32-35 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH + &gpio1 1 GPIO_ACTIVE_HIGH + &gpio1 2 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-18 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_18>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-35-1 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-35-3 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH + &gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-leds-alarm-12 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_alarmled_12>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:alarm"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-20 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22 + &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25 + &pmx_hddled_26 &pmx_hddled_27>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + + hdd3-green { + label = "synology:green:hdd3"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + + hdd3-amber { + label = "synology:amber:hdd3"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; + + hdd4-green { + label = "synology:green:hdd4"; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + + hdd4-amber { + label = "synology:amber:hdd4"; + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-21-1 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-21-2 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-36 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38 + &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41 + &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44 + &pmx_hddled_45>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + hdd3-green { + label = "synology:green:hdd3"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + hdd3-amber { + label = "synology:amber:hdd3"; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + hdd4-green { + label = "synology:green:hdd4"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + hdd4-amber { + label = "synology:amber:hdd4"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + hdd5-green { + label = "synology:green:hdd5"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + + hdd5-amber { + label = "synology:amber:hdd5"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-38 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + }; + + regulators-hdd-29 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>; + pinctrl-names = "default"; + + regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + + regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-1 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30>; + pinctrl-names = "default"; + + regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-2 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>; + pinctrl-names = "default"; + + regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + + regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-4 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34 + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>; + pinctrl-names = "default"; + + regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + + regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "hdd3power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + regulator at 4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "hdd4power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-31 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd2_pwr_31>; + pinctrl-names = "default"; + + regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-34 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44 + &pmx_hdd4_pwr_45>; + pinctrl-names = "default"; + + regulator at 2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "hdd3power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + regulator at 4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "hdd4power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy at 0 { + device_type = "ethernet-phy"; + reg = <8>; + }; + + ethphy1: ethernet-phy at 1 { + device_type = "ethernet-phy"; + reg = <9>; + }; +}; + +ð0 { + status = "okay"; + + ethernet0-port at 0 { + phy-handle = <ðphy0>; + }; +}; + +ð1 { + status = "disabled"; + + ethernet1-port at 0 { + phy-handle = <ðphy1>; + }; +}; -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v7 4/4] ARM: Kirkwood: Add support for many Synology NAS devices 2014-02-19 20:02 ` [PATCH v7 4/4] ARM: Kirkwood: Add support for many Synology NAS devices klightspeed at killerwolves.net @ 2014-02-20 9:11 ` Andrew Lunn 0 siblings, 0 replies; 11+ messages in thread From: Andrew Lunn @ 2014-02-20 9:11 UTC (permalink / raw) To: linux-arm-kernel On Thu, Feb 20, 2014 at 06:02:37AM +1000, klightspeed at killerwolves.net wrote: > From: "Ben Peddell" <klightspeed@killerwolves.net> > > Add device tree fragments and files to support many of the kirkwood > based Synology NAS devices. This is a modification of > Andrew Lunn's <andrew@lunn.ch> translation of the board setup file > maintained by Ben Peddell <klightspeed@killerwolves.net> > > The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units. > All other Synology Kirkwood-based DiskStations and RackStations use > the Seiko S35390A RTC. > > Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed > with the built-in SATA interface activity/presence pins on mpp 20-23, > while the 4-bay units use ge01 and a PCIe SATA controller, and put the > software controlled HDD leds on mpp 36-43. > > Most of the 6281 units with HDD power controls use mpp 29 and 31, while > most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45 > and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and > most 4-bay units didn't have a separate power control for HDD1. These > power controls are presumably to limit startup current from the 12V > brick power supply. > > Instead of using separate dtsi files in a synology directory, this > patch uses a single dtsi file containing all of the modules for > these boards, with all of the modules not common to all boards > disabled. The board dts files then enable the appropriate modules for > their boards. > > Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> > Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j) Since it is based on my code: Signed-off-by: Andrew Lunn <andrew@lunn.ch> Andrew > --- > v2: > Fix gpio's which should be gpo. > Rebase onto v3-14-rc1 > Update RTC nodes with vendor name. > Update SPI flash node with vendor name. > Add a description of the lego > Use ricoy, i.e. the stock ticker > > v3: > Merge Synology dtsi files into single dtsi file > > v4: > Various minor fixes to synology dtsi file > > v7: > Revert ricoh vendor prefix change from v2 > --- > arch/arm/boot/dts/Makefile | 15 + > arch/arm/boot/dts/kirkwood-ds109.dts | 41 ++ > arch/arm/boot/dts/kirkwood-ds110jv10.dts | 41 ++ > arch/arm/boot/dts/kirkwood-ds111.dts | 44 ++ > arch/arm/boot/dts/kirkwood-ds112.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds209.dts | 44 ++ > arch/arm/boot/dts/kirkwood-ds210.dts | 46 ++ > arch/arm/boot/dts/kirkwood-ds212.dts | 47 ++ > arch/arm/boot/dts/kirkwood-ds212j.dts | 41 ++ > arch/arm/boot/dts/kirkwood-ds409.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds409slim.dts | 40 ++ > arch/arm/boot/dts/kirkwood-ds411.dts | 52 ++ > arch/arm/boot/dts/kirkwood-ds411j.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds411slim.dts | 48 ++ > arch/arm/boot/dts/kirkwood-rs212.dts | 48 ++ > arch/arm/boot/dts/kirkwood-rs409.dts | 44 ++ > arch/arm/boot/dts/kirkwood-rs411.dts | 44 ++ > arch/arm/boot/dts/kirkwood-synology.dtsi | 871 +++++++++++++++++++++++++++++++ > 18 files changed, 1610 insertions(+) > create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts > create mode 100644 arch/arm/boot/dts/kirkwood-synology.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 6d1e43d..e286abc 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -90,6 +90,18 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ > kirkwood-dns325.dtb \ > kirkwood-dockstar.dtb \ > kirkwood-dreamplug.dtb \ > + kirkwood-ds109.dtb \ > + kirkwood-ds110jv10.dtb \ > + kirkwood-ds111.dtb \ > + kirkwood-ds209.dtb \ > + kirkwood-ds210.dtb \ > + kirkwood-ds212.dtb \ > + kirkwood-ds212j.dtb \ > + kirkwood-ds409.dtb \ > + kirkwood-ds409slim.dtb \ > + kirkwood-ds411.dtb \ > + kirkwood-ds411j.dtb \ > + kirkwood-ds411slim.dtb \ > kirkwood-goflexnet.dtb \ > kirkwood-guruplug-server-plus.dtb \ > kirkwood-ib62x0.dtb \ > @@ -112,6 +124,9 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ > kirkwood-nsa310a.dtb \ > kirkwood-openblocks_a6.dtb \ > kirkwood-openblocks_a7.dtb \ > + kirkwood-rs212.dtb \ > + kirkwood-rs409.dtb \ > + kirkwood-rs411.dtb \ > kirkwood-sheevaplug.dtb \ > kirkwood-sheevaplug-esata.dtb \ > kirkwood-topkick.dtb \ > diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts > new file mode 100644 > index 0000000..772092c > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds109.dts > @@ -0,0 +1,41 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS109, DS110, DS110jv20"; > + compatible = "synology,ds109", "synology,ds110jv20", > + "synology,ds110", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "okay"; > + }; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts > new file mode 100644 > index 0000000..aabafbe > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts > @@ -0,0 +1,41 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS110j v10 and v30"; > + compatible = "synology,ds110jv10", "synology,ds110jv30", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts > new file mode 100644 > index 0000000..16ec7fb > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds111.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS111"; > + compatible = "synology,ds111", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts > new file mode 100644 > index 0000000..cff1b23 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds112.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS111"; > + compatible = "synology,ds111", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-21-2 { > + status = "okay"; > + }; > + > + regulators-hdd-30 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts > new file mode 100644 > index 0000000..3304119 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds209.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS209"; > + compatible = "synology,ds209", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > + > + regulators-hdd-31 { > + status = "okay"; > + }; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts > new file mode 100644 > index 0000000..6052eaa > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds210.dts > @@ -0,0 +1,46 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS210 v10, v20, v30, DS211j"; > + compatible = "synology,ds210jv10", "synology,ds210jv20", > + "synology,ds210jv30", "synology,ds211j", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > + > + regulators-hdd-31 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts > new file mode 100644 > index 0000000..7f76cd3 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds212.dts > @@ -0,0 +1,47 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10"; > + compatible = "synology,ds212", "synology,ds212pv10", > + "synology,ds212pv10", "synology,ds212pv20", > + "synology,ds213airv10", "synology,ds213v10", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts > new file mode 100644 > index 0000000..1f83a00 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts > @@ -0,0 +1,41 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS212j v10, v20"; > + compatible = "synology,ds212jv10", "synology,ds212jv20", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts > new file mode 100644 > index 0000000..0a573ad > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds409.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS409, DS410j"; > + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-15-18 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > + > + gpio-leds-alarm-12 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts > new file mode 100644 > index 0000000..1848a62 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts > @@ -0,0 +1,40 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology 409slim"; > + compatible = "synology,ds409slim", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-20 { > + status = "okay"; > + }; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts > new file mode 100644 > index 0000000..a1737b4 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds411.dts > @@ -0,0 +1,52 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS411, DS413jv10"; > + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > + > + regulators-hdd-34 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts > new file mode 100644 > index 0000000..0cde914 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS411j"; > + compatible = "synology,ds411j", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-15-18 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > + > + gpio-leds-alarm-12 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts > new file mode 100644 > index 0000000..aef0cad > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS411slim"; > + compatible = "synology,ds411slim", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts > new file mode 100644 > index 0000000..93ec3d0 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-rs212.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology RS212"; > + compatible = "synology,rs212", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-3 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-38 { > + status = "okay"; > + }; > + > + regulators-hdd-30-2 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts > new file mode 100644 > index 0000000..311df4e > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-rs409.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology RS409"; > + compatible = "synology,rs409", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-15-18 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts > new file mode 100644 > index 0000000..f90da85 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-rs411.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology RS411 RS812"; > + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-3 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/kirkwood-synology.dtsi > new file mode 100644 > index 0000000..92b3177 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-synology.dtsi > @@ -0,0 +1,871 @@ > +/* > + * Nodes for Marvell 628x Synology devices > + * > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/ { > + mbus { > + pcie-controller { > + status = "okay"; > + > + pcie at 1,0 { > + status = "okay"; > + }; > + > + pcie2: pcie at 2,0 { > + status = "disabled"; > + }; > + }; > + }; > + > + ocp at f1000000 { > + pinctrl: pinctrl at 10000 { > + pmx_alarmled_12: pmx-alarmled-12 { > + marvell,pins = "mpp12"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_15: pmx-fanctrl-15 { > + marvell,pins = "mpp15"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_16: pmx-fanctrl-16 { > + marvell,pins = "mpp16"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_17: pmx-fanctrl-17 { > + marvell,pins = "mpp17"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_18: pmx-fanalarm-18 { > + marvell,pins = "mpp18"; > + marvell,function = "gpo"; > + }; > + > + pmx_hddled_20: pmx-hddled-20 { > + marvell,pins = "mpp20"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_21: pmx-hddled-21 { > + marvell,pins = "mpp21"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_22: pmx-hddled-22 { > + marvell,pins = "mpp22"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_23: pmx-hddled-23 { > + marvell,pins = "mpp23"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_24: pmx-hddled-24 { > + marvell,pins = "mpp24"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_25: pmx-hddled-25 { > + marvell,pins = "mpp25"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_26: pmx-hddled-26 { > + marvell,pins = "mpp26"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_27: pmx-hddled-27 { > + marvell,pins = "mpp27"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_28: pmx-hddled-28 { > + marvell,pins = "mpp28"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 { > + marvell,pins = "mpp29"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 { > + marvell,pins = "mpp30"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 { > + marvell,pins = "mpp31"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_32: pmx-fanctrl-32 { > + marvell,pins = "mpp32"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_33: pmx-fanctrl-33 { > + marvell,pins = "mpp33"; > + marvell,function = "gpo"; > + }; > + > + pmx_fanctrl_34: pmx-fanctrl-34 { > + marvell,pins = "mpp34"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 { > + marvell,pins = "mpp34"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_35: pmx-fanalarm-35 { > + marvell,pins = "mpp35"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_36: pmx-hddled-36 { > + marvell,pins = "mpp36"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_37: pmx-hddled-37 { > + marvell,pins = "mpp37"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_38: pmx-hddled-38 { > + marvell,pins = "mpp38"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_39: pmx-hddled-39 { > + marvell,pins = "mpp39"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_40: pmx-hddled-40 { > + marvell,pins = "mpp40"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_41: pmx-hddled-41 { > + marvell,pins = "mpp41"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_42: pmx-hddled-42 { > + marvell,pins = "mpp42"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_43: pmx-hddled-43 { > + marvell,pins = "mpp43"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_44: pmx-hddled-44 { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_45: pmx-hddled-45 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_44: pmx-fanalarm-44 { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_45: pmx-fanalarm-45 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + }; > + > + rtc at 10300 { > + status = "disabled"; > + }; > + > + spi at 10600 { > + status = "okay"; > + pinctrl-0 = <&pmx_spi>; > + pinctrl-names = "default"; > + > + m25p80 at 0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "st,m25p80"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + mode = <0>; > + > + partition at 00000000 { > + reg = <0x00000000 0x00080000>; > + label = "RedBoot"; > + }; > + > + partition at 00080000 { > + reg = <0x00080000 0x00200000>; > + label = "zImage"; > + }; > + > + partition at 00280000 { > + reg = <0x00280000 0x00140000>; > + label = "rd.gz"; > + }; > + > + partition at 003c0000 { > + reg = <0x003c0000 0x00010000>; > + label = "vendor"; > + }; > + > + partition at 003d0000 { > + reg = <0x003d0000 0x00020000>; > + label = "RedBoot config"; > + }; > + > + partition at 003f0000 { > + reg = <0x003f0000 0x00010000>; > + label = "FIS directory"; > + }; > + }; > + }; > + > + i2c at 11000 { > + status = "okay"; > + clock-frequency = <400000>; > + pinctrl-0 = <&pmx_twsi0>; > + pinctrl-names = "default"; > + > + rs5c372: rs5c372 at 32 { > + status = "disabled"; > + compatible = "ricoh,rs5c372"; > + reg = <0x32>; > + }; > + > + s35390a: s35390a at 30 { > + status = "disabled"; > + compatible = "ssi,s35390a"; > + reg = <0x30>; > + }; > + }; > + > + serial at 12000 { > + status = "okay"; > + pinctrl-0 = <&pmx_uart0>; > + pinctrl-names = "default"; > + }; > + > + serial at 12100 { > + status = "okay"; > + pinctrl-0 = <&pmx_uart1>; > + pinctrl-names = "default"; > + }; > + > + poweroff at 12100 { > + compatible = "synology,power-off"; > + reg = <0x12100 0x100>; > + clocks = <&gate_clk 7>; > + }; > + > + sata at 80000 { > + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; > + pinctrl-names = "default"; > + status = "okay"; > + nr-ports = <2>; > + }; > + }; > + > + gpio-fan-150-32-35 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 > + &pmx_fanalarm_35>; > + pinctrl-names = "default"; > + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH > + &gpio1 1 GPIO_ACTIVE_HIGH > + &gpio1 2 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2200 1 > + 2500 2 > + 3000 4 > + 3300 3 > + 3700 5 > + 3800 6 > + 4200 7 >; > + }; > + > + gpio-fan-150-15-18 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_18>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2200 1 > + 2500 2 > + 3000 4 > + 3300 3 > + 3700 5 > + 3800 6 > + 4200 7 >; > + }; > + > + gpio-fan-100-32-35 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 > + &pmx_fanalarm_35>; > + pinctrl-names = "default"; > + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH > + &gpio1 1 GPIO_ACTIVE_HIGH > + &gpio1 2 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-fan-100-15-18 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_18>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_35>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-fan-100-15-35-3 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH > + &gpio1 12 GPIO_ACTIVE_HIGH > + &gpio1 13 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-leds-alarm-12 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_alarmled_12>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:alarm"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-20 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22 > + &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25 > + &pmx_hddled_26 &pmx_hddled_27>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-green { > + label = "synology:green:hdd3"; > + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-amber { > + label = "synology:amber:hdd3"; > + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-green { > + label = "synology:green:hdd4"; > + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-amber { > + label = "synology:amber:hdd4"; > + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-36 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38 > + &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41 > + &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44 > + &pmx_hddled_45>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-green { > + label = "synology:green:hdd3"; > + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-amber { > + label = "synology:amber:hdd3"; > + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-green { > + label = "synology:green:hdd4"; > + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-amber { > + label = "synology:amber:hdd4"; > + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; > + }; > + > + hdd5-green { > + label = "synology:green:hdd5"; > + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; > + }; > + > + hdd5-amber { > + label = "synology:amber:hdd5"; > + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-38 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + regulators-hdd-29 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>; > + pinctrl-names = "default"; > + > + regulator at 1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-30-1 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_30>; > + pinctrl-names = "default"; > + > + regulator at 1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-30-2 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>; > + pinctrl-names = "default"; > + > + regulator at 1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-30-4 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34 > + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>; > + pinctrl-names = "default"; > + > + regulator at 1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 3 { > + compatible = "regulator-fixed"; > + reg = <3>; > + regulator-name = "hdd3power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 4 { > + compatible = "regulator-fixed"; > + reg = <4>; > + regulator-name = "hdd4power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-31 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd2_pwr_31>; > + pinctrl-names = "default"; > + > + regulator at 1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-34 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44 > + &pmx_hdd4_pwr_45>; > + pinctrl-names = "default"; > + > + regulator at 2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 3 { > + compatible = "regulator-fixed"; > + reg = <3>; > + regulator-name = "hdd3power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator at 4 { > + compatible = "regulator-fixed"; > + reg = <4>; > + regulator-name = "hdd4power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + }; > + }; > +}; > + > +&mdio { > + status = "okay"; > + > + ethphy0: ethernet-phy at 0 { > + device_type = "ethernet-phy"; > + reg = <8>; > + }; > + > + ethphy1: ethernet-phy at 1 { > + device_type = "ethernet-phy"; > + reg = <9>; > + }; > +}; > + > +ð0 { > + status = "okay"; > + > + ethernet0-port at 0 { > + phy-handle = <ðphy0>; > + }; > +}; > + > +ð1 { > + status = "disabled"; > + > + ethernet1-port at 0 { > + phy-handle = <ðphy1>; > + }; > +}; > -- > 1.8.3.2 > ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net ` (3 preceding siblings ...) 2014-02-19 20:02 ` [PATCH v7 4/4] ARM: Kirkwood: Add support for many Synology NAS devices klightspeed at killerwolves.net @ 2014-02-20 9:18 ` Andrew Lunn 2014-02-22 1:56 ` Jason Cooper 5 siblings, 0 replies; 11+ messages in thread From: Andrew Lunn @ 2014-02-20 9:18 UTC (permalink / raw) To: linux-arm-kernel On Thu, Feb 20, 2014 at 06:02:33AM +1000, klightspeed at killerwolves.net wrote: > This patchset adds support for around 30 kirkwood bases Synology NAS > boxes. Patch #1 documents vendor prefixes. Patch #2 generalizes the qnap > power off driver so that it can also be used for Synology devices. > Patch #3 adds sii,s35390a to i2c trivial devices. Patch #4 adds the > synology DT files. Hi Ben Thanks for finishing this. Whole series: Acked-by: Andrew Lunn <andrew@lunn.ch> Andrew ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net ` (4 preceding siblings ...) 2014-02-20 9:18 ` [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes Andrew Lunn @ 2014-02-22 1:56 ` Jason Cooper 5 siblings, 0 replies; 11+ messages in thread From: Jason Cooper @ 2014-02-22 1:56 UTC (permalink / raw) To: linux-arm-kernel Ben, On Thu, Feb 20, 2014 at 06:02:33AM +1000, klightspeed at killerwolves.net wrote: > This patchset adds support for around 30 kirkwood bases Synology NAS > boxes. Patch #1 documents vendor prefixes. Patch #2 generalizes the qnap > power off driver so that it can also be used for Synology devices. > Patch #3 adds sii,s35390a to i2c trivial devices. Patch #4 adds the > synology DT files. ... > Andrew Lunn (3): > DT: Vendor prefixes: Add ricoh, qnap, sii and synology > Power: Reset: Generalize qnap-poweroff to with on Synology devices. > DT: i2c: Trivial: Add sii,s35390a > > Ben Peddell (1): > ARM: Kirkwood: Add support for many Synology NAS devices > > .../devicetree/bindings/i2c/trivial-devices.txt | 1 + > .../bindings/power_supply/qnap-poweroff.txt | 5 +- > .../devicetree/bindings/vendor-prefixes.txt | 4 + > arch/arm/boot/dts/Makefile | 15 + > arch/arm/boot/dts/kirkwood-ds109.dts | 41 + > arch/arm/boot/dts/kirkwood-ds110jv10.dts | 41 + > arch/arm/boot/dts/kirkwood-ds111.dts | 44 ++ > arch/arm/boot/dts/kirkwood-ds112.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds209.dts | 44 ++ > arch/arm/boot/dts/kirkwood-ds210.dts | 46 ++ > arch/arm/boot/dts/kirkwood-ds212.dts | 47 ++ > arch/arm/boot/dts/kirkwood-ds212j.dts | 41 + > arch/arm/boot/dts/kirkwood-ds409.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds409slim.dts | 40 + > arch/arm/boot/dts/kirkwood-ds411.dts | 52 ++ > arch/arm/boot/dts/kirkwood-ds411j.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds411slim.dts | 48 ++ > arch/arm/boot/dts/kirkwood-rs212.dts | 48 ++ > arch/arm/boot/dts/kirkwood-rs409.dts | 44 ++ > arch/arm/boot/dts/kirkwood-rs411.dts | 44 ++ > arch/arm/boot/dts/kirkwood-synology.dtsi | 871 +++++++++++++++++++++ > drivers/power/reset/qnap-poweroff.c | 49 +- > 22 files changed, 1656 insertions(+), 13 deletions(-) > create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts > create mode 100644 arch/arm/boot/dts/kirkwood-synology.dtsi I applied patches 1, 3, and 4 to mvebu/dt. Thanks and good work! Jason. ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2014-03-04 3:54 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-02-19 20:02 [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes klightspeed at killerwolves.net 2014-02-19 20:02 ` [PATCH v7 1/4] DT: Vendor prefixes: Add ricoh, qnap, sii and synology klightspeed at killerwolves.net 2014-02-19 21:17 ` Rob Herring 2014-02-19 20:02 ` [PATCH v7 2/4] Power: Reset: Generalize qnap-poweroff to work on Synology devices klightspeed at killerwolves.net 2014-02-22 1:39 ` Jason Cooper 2014-03-04 3:54 ` Jason Cooper 2014-02-19 20:02 ` [PATCH v7 3/4] DT: i2c: Trivial: Add sii,s35390a klightspeed at killerwolves.net 2014-02-19 20:02 ` [PATCH v7 4/4] ARM: Kirkwood: Add support for many Synology NAS devices klightspeed at killerwolves.net 2014-02-20 9:11 ` Andrew Lunn 2014-02-20 9:18 ` [PATCH v7 0/4] DT support for kirkwood based Synology NAS boxes Andrew Lunn 2014-02-22 1:56 ` Jason Cooper
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).