From: sr@denx.de (Stefan Roese)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] arm: dts: Add support for Compulab sbc-t3530 with cm-t35
Date: Fri, 21 Feb 2014 13:36:05 +0100 [thread overview]
Message-ID: <1392986165-12238-1-git-send-email-sr@denx.de> (raw)
The cm-t3530 SOM is equipped with the OMAP3530 and does not boot with
the cm-t3730 dts file as it used the omap36xx.dtsi. Add a separate
dts/dtsi for this board to support it correctly.
I moved some common parts into omap3-cm-t3x30.dtsi. And removed
the SDIO/WLAN support for now. As I don't know exactly how this
should be done. Perhaps somebody else might jump in here...
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/omap3-cm-t3530.dts | 29 +++++++++++++++++++
arch/arm/boot/dts/omap3-cm-t3730.dts | 54 ++++-------------------------------
arch/arm/boot/dts/omap3-cm-t3x30.dtsi | 44 ++++++++++++++++++++++++++++
arch/arm/boot/dts/omap3-sbc-t3530.dts | 30 +++++++++++++++++++
5 files changed, 110 insertions(+), 48 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-cm-t3530.dts
create mode 100644 arch/arm/boot/dts/omap3-sbc-t3530.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6d1e43d..6fd1b34 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -200,6 +200,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
omap3430-sdp.dtb \
omap3-beagle.dtb \
omap3-cm-t3730.dtb \
+ omap3-sbc-t3530.dtb \
omap3-sbc-t3730.dtb \
omap3-devkit8000.dtb \
omap3-beagle-xm.dtb \
diff --git a/arch/arm/boot/dts/omap3-cm-t3530.dts b/arch/arm/boot/dts/omap3-cm-t3530.dts
new file mode 100644
index 0000000..35a1fc2
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3530.dts
@@ -0,0 +1,29 @@
+/*
+ * Support for CompuLab CM-T3530
+ */
+/dts-v1/;
+
+#include "omap34xx-hs.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+ model = "CompuLab CM-T3530";
+ compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
+&smsc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts
index 486f4d6..3e05b11 100644
--- a/arch/arm/boot/dts/omap3-cm-t3730.dts
+++ b/arch/arm/boot/dts/omap3-cm-t3730.dts
@@ -32,39 +32,14 @@
};
&omap3_pmx_core {
- mmc1_pins: pinmux_mmc1_pins {
- pinctrl-single,pins = <
- 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
- 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
- 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
- 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
- 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
- >;
- };
-
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
- 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
- 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
- 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
- 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
- >;
- };
-
- smsc1_pins: pinmux_smsc1_pins {
- pinctrl-single,pins = <
- 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
- 0x16a (PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
>;
};
@@ -76,13 +51,6 @@
};
};
-&mmc1 {
- vmmc-supply = <&vmmc1>;
- bus-width = <4>;
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
-};
-
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
@@ -92,13 +60,3 @@
bus-width = <4>;
cap-power-off-card;
};
-
-&smsc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&smsc1_pins>;
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
-};
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
index 3a9f004..0eadd4a 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -36,6 +36,33 @@
};
};
+&omap3_pmx_core {
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+
+ smsc1_pins: pinmux_smsc1_pins {
+ pinctrl-single,pins = <
+ 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */
+ 0x16a (PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+};
+
&gpmc {
ranges = <5 0 0x2c000000 0x01000000>;
@@ -83,6 +110,23 @@
};
};
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
+&smsc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
diff --git a/arch/arm/boot/dts/omap3-sbc-t3530.dts b/arch/arm/boot/dts/omap3-sbc-t3530.dts
new file mode 100644
index 0000000..b548343
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-sbc-t3530.dts
@@ -0,0 +1,30 @@
+/*
+ * Support for CompuLab SBC-T3530 with CM-T3530
+ */
+
+#include "omap3-cm-t3530.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+ model = "CompuLab SBC-T3530 with CM-T3530";
+ compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&gpmc {
+ ranges = <5 0 0x2c000000 0x01000000>,
+ <4 0 0x2d000000 0x01000000>;
+};
+
+&smsc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc2_pins>;
+};
+
+&omap3_pmx_core {
+ smsc2_pins: pinmux_smsc2_pins {
+ pinctrl-single,pins = <
+ 0x86 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */
+ 0xa2 (PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */
+ >;
+ };
+};
--
1.8.5.5
next reply other threads:[~2014-02-21 12:36 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-21 12:36 Stefan Roese [this message]
2014-02-23 12:33 ` [PATCH] arm: dts: Add support for Compulab sbc-t3530 with cm-t35 Igor Grinberg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1392986165-12238-1-git-send-email-sr@denx.de \
--to=sr@denx.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).