From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 12/22] ARM: Fix default CPU selection for ARCH_MULTI_V5
Date: Sat, 22 Feb 2014 20:14:54 +0100 [thread overview]
Message-ID: <1393096504-11844-13-git-send-email-andrew@lunn.ch> (raw)
In-Reply-To: <1393096504-11844-1-git-send-email-andrew@lunn.ch>
CPU_ARM926T should be selected if no other CPU is. Put the ! in the
right place so this works.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
---
arch/arm/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index e25419817791..beba369d74de 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -898,7 +898,7 @@ config ARCH_MULTI_V5
bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
depends on !ARCH_MULTI_V6_V7
select ARCH_MULTI_V4_V5
- select CPU_ARM926T if (!CPU_ARM946E || CPU_ARM1020 || \
+ select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \
CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
--
1.8.5.3
next prev parent reply other threads:[~2014-02-22 19:14 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-22 19:14 [PATCH v4 00/22] Move DT kirkwood into mach-mvebu Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 01/22] ARM: Kirkwood: Give pm.c its own header file Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 02/22] irqchip: Orion: Fix getting generic chip pointer Andrew Lunn
2014-02-22 19:46 ` Jason Cooper
2014-02-22 19:14 ` [PATCH v4 03/22] ARM: Kirkwood: Convert mv88f6281gtw_ge switch setup to DT Andrew Lunn
2014-02-22 19:50 ` Jason Cooper
2014-02-22 20:20 ` Andrew Lunn
2014-02-22 20:23 ` Jason Cooper
2014-02-22 19:14 ` [PATCH v4 04/22] ARM: Kirkwood: Drop printing the SoC type and revision Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 05/22] ARM: Kirkwood: Seperate board-dt from common and pcie code Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 06/22] ARM: Kirkwood: ioremap the cpu_config register before using it Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 07/22] ARM: Kirkwood: ioremap memory control register Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 08/22] ARM: MVEBU: Add ARCH_MULTI_V7 to SoCs Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 09/22] ARM: Orion: Move cache-feroceon-l2.h out of plat-orion Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 10/22] ARM: MM: Add DT binding for Feroceon L2 cache Andrew Lunn
2014-02-22 20:11 ` Jason Cooper
2014-02-22 19:14 ` [PATCH v4 11/22] ARM: Kirkwood: Instantiate L2 cache from DT Andrew Lunn
2014-02-22 19:14 ` Andrew Lunn [this message]
2014-02-22 19:58 ` [PATCH v4 12/22] ARM: Fix default CPU selection for ARCH_MULTI_V5 Jason Cooper
2014-02-22 19:14 ` [PATCH v4 13/22] ARM: Fix MULTI_TLB for feroceon Andrew Lunn
2014-02-22 20:03 ` Jason Cooper
2014-02-22 19:14 ` [PATCH v4 14/22] ARM: MM Enable building Feroceon L2 cache controller with ARCH_MVEBU Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 15/22] ARM: Move kirkwood DT boards into mach-mvebu Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 16/22] ARM: MVEBU: Let kirkwood use the system controller for restart Andrew Lunn
2014-02-22 19:14 ` [PATCH v4 17/22] ARM: MVEBU: Instantiate system controller in kirkwood.dtsi Andrew Lunn
2014-02-22 19:15 ` [PATCH v4 18/22] drivers: Enable building of Kirkwood drivers for mach-mvebu Andrew Lunn
2014-02-24 5:37 ` Viresh Kumar
2014-02-24 17:32 ` Jason Cooper
2014-03-27 17:35 ` Bryan Wu
2014-02-22 19:15 ` [PATCH v4 19/22] ARM: MVEBU: Enable mvebu-soc-id on Kirkwood Andrew Lunn
2014-02-22 19:15 ` [PATCH v4 20/22] ARM: config: Add a multi_v5_defconfig Andrew Lunn
2014-02-22 19:15 ` [PATCH v4 21/22] ARM: MVEBU: Simplifiy headers and make local Andrew Lunn
2014-02-22 19:15 ` [PATCH v4 22/22] ARM: config: Add mvebu_v5_defconfig Andrew Lunn
2014-02-22 22:16 ` [PATCH v4 00/22] Move DT kirkwood into mach-mvebu Jason Cooper
2014-02-23 11:14 ` Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1393096504-11844-13-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).