From: florian.vaussard@epfl.ch (Florian Vaussard)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 5/9] ARM: dts: omap3-overo: Add HSUSB PHY
Date: Fri, 7 Mar 2014 20:22:15 +0100 [thread overview]
Message-ID: <1394220139-1760-6-git-send-email-florian.vaussard@epfl.ch> (raw)
In-Reply-To: <1394220139-1760-1-git-send-email-florian.vaussard@epfl.ch>
Add the High-Speed USB PHY.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
---
arch/arm/boot/dts/omap3-overo-base.dtsi | 44 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/omap3-overo-storm.dtsi | 16 ++++++++++++
arch/arm/boot/dts/omap3-overo.dtsi | 16 ++++++++++++
3 files changed, 76 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi
index edac70e..13d1ad2 100644
--- a/arch/arm/boot/dts/omap3-overo-base.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-base.dtsi
@@ -30,6 +30,24 @@
ti,codec = <&twl_audio>;
};
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio6 8 0>; /* gpio_168: vbus enable */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; /* gpio_183 */
+ vcc-supply = <&hsusb2_power>;
+ };
+
/* Regulator to trigger the nPoweron signal of the Wifi module */
w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
compatible = "regulator-fixed";
@@ -64,6 +82,11 @@
};
&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_pins
+ >;
+
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */
@@ -116,6 +139,19 @@
OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
>;
};
+
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */
+ OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4) /* i2c2_sda.gpio_183 */
+ >;
+ };
};
&i2c1 {
@@ -177,6 +213,14 @@
power = <50>;
};
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
diff --git a/arch/arm/boot/dts/omap3-overo-storm.dtsi b/arch/arm/boot/dts/omap3-overo-storm.dtsi
index c235ae8..6cb418b 100644
--- a/arch/arm/boot/dts/omap3-overo-storm.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-storm.dtsi
@@ -10,6 +10,22 @@
#include "omap3-overo-base.dtsi"
&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_2_pins
+ >;
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+
w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
pinctrl-single,pins = <
OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
index 95c59b2..c37b130 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/omap3-overo.dtsi
@@ -10,6 +10,22 @@
#include "omap3-overo-base.dtsi"
&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusb2_2_pins
+ >;
+
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+
w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
pinctrl-single,pins = <
OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
--
1.8.3.2
next prev parent reply other threads:[~2014-03-07 19:22 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-03-07 19:22 [PATCH v4 0/9] ARM: dts: Better support for Gumstix Overo (for 3.15?) Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 1/9] ARM: dts: overo: reorganize include files Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 2/9] ARM: dts: omap3-tobi: Add missing pinctrl Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 3/9] ARM: dts: omap3-overo: " Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 4/9] ARM: dts: omap3-overo: Enable WiFi/BT combo Florian Vaussard
2014-03-07 19:22 ` Florian Vaussard [this message]
2014-03-10 10:30 ` [PATCH v4 5/9] ARM: dts: omap3-overo: Add HSUSB PHY Roger Quadros
2014-03-10 15:13 ` Florian Vaussard
2014-03-10 18:03 ` Tony Lindgren
2014-03-11 6:28 ` Florian Vaussard
2014-03-11 9:43 ` Roger Quadros
2014-03-12 17:19 ` Tony Lindgren
2014-03-13 8:29 ` Florian Vaussard
2014-03-11 9:43 ` Roger Quadros
2014-03-07 19:22 ` [PATCH v4 6/9] ARM: dts: omap: Add common file for SMSC9221 Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 7/9] ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221 Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 8/9] ARM: dts: omap3-tobi: Add AT24C01 EEPROM Florian Vaussard
2014-03-07 19:22 ` [PATCH v4 9/9] ARM: dts: overo: Push uart3 pinmux down to expansion board Florian Vaussard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1394220139-1760-6-git-send-email-florian.vaussard@epfl.ch \
--to=florian.vaussard@epfl.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).