From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6 01/36] mtd: st_spi_fsm: Allocate resources and register with MTD framework
Date: Thu, 20 Mar 2014 09:20:33 +0000 [thread overview]
Message-ID: <1395307268-12721-2-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1395307268-12721-1-git-send-email-lee.jones@linaro.org>
This is a new driver. It's used to communicate with a special type of
optimised Serial Flash Controller called the FSM. The FSM uses a subset
of the SPI protocol to communicate with supported NOR-Flash devices.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
drivers/mtd/devices/Kconfig | 8 +++
drivers/mtd/devices/Makefile | 1 +
drivers/mtd/devices/st_spi_fsm.c | 106 +++++++++++++++++++++++++++++++++++++++
3 files changed, 115 insertions(+)
create mode 100644 drivers/mtd/devices/st_spi_fsm.c
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 0128138..1210bc2 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -210,6 +210,14 @@ config MTD_DOCG3
M-Systems and now Sandisk. The support is very experimental,
and doesn't give access to any write operations.
+config MTD_ST_SPI_FSM
+ tristate "ST Microelectronics SPI FSM Serial Flash Controller"
+ depends on ARM || SH
+ help
+ This provides an MTD device driver for the ST Microelectronics
+ SPI Fast Sequence Mode (FSM) Serial Flash Controller and support
+ for a subset of connected Serial Flash devices.
+
if MTD_DOCG3
config BCH_CONST_M
default 14
diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile
index d83bd73..c68868f 100644
--- a/drivers/mtd/devices/Makefile
+++ b/drivers/mtd/devices/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_MTD_NAND_OMAP_BCH) += elm.o
obj-$(CONFIG_MTD_SPEAR_SMI) += spear_smi.o
obj-$(CONFIG_MTD_SST25L) += sst25l.o
obj-$(CONFIG_MTD_BCM47XXSFLASH) += bcm47xxsflash.o
+obj-$(CONFIG_MTD_ST_SPI_FSM) += st_spi_fsm.o
CFLAGS_docg3.o += -I$(src)
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
new file mode 100644
index 0000000..b1e6740
--- /dev/null
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -0,0 +1,106 @@
+/*
+ * st_spi_fsm.c - ST Fast Sequence Mode (FSM) Serial Flash Controller
+ *
+ * Author: Angus Clark <angus.clark@st.com>
+ *
+ * Copyright (C) 2010-2014 STicroelectronics Limited
+ *
+ * JEDEC probe based on drivers/mtd/devices/m25p80.c
+ *
+ * This code is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/sched.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/of.h>
+
+struct stfsm {
+ struct device *dev;
+ void __iomem *base;
+ struct resource *region;
+ struct mtd_info mtd;
+ struct mutex lock;
+};
+
+static int stfsm_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct resource *res;
+ struct stfsm *fsm;
+
+ if (!np) {
+ dev_err(&pdev->dev, "No DT found\n");
+ return -EINVAL;
+ }
+
+ fsm = devm_kzalloc(&pdev->dev, sizeof(*fsm), GFP_KERNEL);
+ if (!fsm)
+ return -ENOMEM;
+
+ fsm->dev = &pdev->dev;
+
+ platform_set_drvdata(pdev, fsm);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Resource not found\n");
+ return -ENODEV;
+ }
+
+ fsm->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(fsm->base)) {
+ dev_err(&pdev->dev,
+ "Failed to reserve memory region %pR\n", res);
+ return PTR_ERR(fsm->base);
+ }
+
+ mutex_init(&fsm->lock);
+
+ fsm->mtd.dev.parent = &pdev->dev;
+ fsm->mtd.type = MTD_NORFLASH;
+ fsm->mtd.writesize = 4;
+ fsm->mtd.writebufsize = fsm->mtd.writesize;
+ fsm->mtd.flags = MTD_CAP_NORFLASH;
+
+ return mtd_device_parse_register(&fsm->mtd, NULL, NULL, NULL, 0);
+}
+
+static int stfsm_remove(struct platform_device *pdev)
+{
+ struct stfsm *fsm = platform_get_drvdata(pdev);
+ int err;
+
+ err = mtd_device_unregister(&fsm->mtd);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+static struct of_device_id stfsm_match[] = {
+ { .compatible = "st,spi-fsm", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, stfsm_match);
+
+static struct platform_driver stfsm_driver = {
+ .probe = stfsm_probe,
+ .remove = stfsm_remove,
+ .driver = {
+ .name = "st-spi-fsm",
+ .owner = THIS_MODULE,
+ .of_match_table = stfsm_match,
+ },
+};
+module_platform_driver(stfsm_driver);
+
+MODULE_AUTHOR("Angus Clark <angus.clark@st.com>");
+MODULE_DESCRIPTION("ST SPI FSM driver");
+MODULE_LICENSE("GPL");
--
1.8.3.2
next prev parent reply other threads:[~2014-03-20 9:20 UTC|newest]
Thread overview: 45+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-03-20 9:20 [PATCH v6 00/36] mtd: st_spi_fsm: Add new driver Lee Jones
2014-03-20 9:20 ` Lee Jones [this message]
2014-04-07 8:12 ` [PATCH v6 01/36] mtd: st_spi_fsm: Allocate resources and register with MTD framework Paul Bolle
2014-04-07 9:11 ` Lee Jones
2014-04-07 9:41 ` Paul Bolle
2014-04-07 11:08 ` Lee Jones
2014-03-20 9:20 ` [PATCH v6 02/36] mtd: st_spi_fsm: Supply all register address and bit logic defines Lee Jones
2014-03-20 9:20 ` [PATCH v6 03/36] mtd: st_spi_fsm: Initialise and configure the FSM for normal working conditions Lee Jones
2014-03-20 9:20 ` [PATCH v6 04/36] mtd: st_spi_fsm: Supply framework for device requests Lee Jones
2014-03-20 9:20 ` [PATCH v6 05/36] mtd: st_spi_fsm: Supply a method to read from the FSM's FIFO Lee Jones
2014-03-20 9:20 ` [PATCH v6 06/36] mtd: st_spi_fsm: Add support for JEDEC ID extraction Lee Jones
2014-03-20 9:20 ` [PATCH v6 07/36] mtd: devices: Provide header for shared OPCODEs and SFDP commands Lee Jones
2014-03-20 9:20 ` [PATCH v6 08/36] mtd: st_spi_fsm: Provide device look-up table Lee Jones
2014-03-20 9:20 ` [PATCH v6 09/36] mtd: st_spi_fsm: Dynamically setup flash device based on JEDEC ID Lee Jones
2014-03-20 9:20 ` [PATCH v6 10/36] mtd: st_spi_fsm: Search for preferred FSM message sequence configurations Lee Jones
2014-03-20 9:20 ` [PATCH v6 11/36] mtd: st_spi_fsm: Use device size to determine address width Lee Jones
2014-03-20 9:20 ` [PATCH v6 12/36] mtd: st_spi_fsm: Prepare the read/write FSM message sequence(s) Lee Jones
2014-03-20 9:20 ` [PATCH v6 13/36] mtd: st_spi_fsm: Add device-tree binding documentation Lee Jones
2014-03-20 9:20 ` [PATCH v6 14/36] mtd: st_spi_fsm: Fetch boot-device from mode pins Lee Jones
2014-03-20 9:20 ` [PATCH v6 15/36] mtd: st_spi_fsm: Provide the erase one sector sequence Lee Jones
2014-03-20 9:20 ` [PATCH v6 16/36] mtd: st_spi_fsm: Provide the sequence for enabling 32bit addressing mode Lee Jones
2014-03-20 9:20 ` [PATCH v6 17/36] mtd: st_spi_fsm: Prepare read/write sequences according to configuration Lee Jones
2014-03-20 9:20 ` [PATCH v6 18/36] mtd: st_spi_fsm: Add a check to if the chip can handle an SoC reset Lee Jones
2014-03-20 9:20 ` [PATCH v6 19/36] mtd: st_spi_fsm: Provide a method to put the chip into 32bit addressing mode Lee Jones
2014-03-20 9:20 ` [PATCH v6 20/36] mtd: st_spi_fsm: Update the flash Volatile Configuration Register Lee Jones
2014-03-20 9:20 ` [PATCH v6 21/36] mtd: st_spi_fsm: Provide the default read/write configurations Lee Jones
2014-03-20 9:20 ` [PATCH v6 22/36] mtd: st_spi_fsm: Supply the N25Qxxx specific read configurations Lee Jones
2014-03-20 9:20 ` [PATCH v6 23/36] mtd: st_spi_fsm: Supply the N25Qxxx chip specific configuration call-back Lee Jones
2014-03-20 9:20 ` [PATCH v6 24/36] mtd: st_spi_fsm: Prepare default sequences for read/write/erase Lee Jones
2014-03-20 9:20 ` [PATCH v6 25/36] mtd: st_spi_fsm: Add the ability to read from a Serial Flash device Lee Jones
2014-03-20 9:20 ` [PATCH v6 26/36] mtd: st_spi_fsm: Write to Flash via the FSM FIFO Lee Jones
2014-03-20 9:20 ` [PATCH v6 27/36] mtd: st_spi_fsm: Supply a busy wait for post-write status Lee Jones
2014-03-20 9:21 ` [PATCH v6 28/36] mtd: st_spi_fsm: Erase partly or as a whole a Serial Flash device Lee Jones
2014-03-20 9:21 ` [PATCH v6 29/36] mtd: st_spi_fsm: Add the ability to read the FSM's status Lee Jones
2014-03-20 9:21 ` [PATCH v6 30/36] mtd: st_spi_fsm: Add the ability to write to FSM's status register Lee Jones
2014-03-20 9:21 ` [PATCH v6 31/36] mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back Lee Jones
2014-03-20 9:21 ` [PATCH v6 32/36] mtd: st_spi_fsm: Supply the S25FLxxx " Lee Jones
2014-03-20 9:21 ` [PATCH v6 33/36] mtd: st_spi_fsm: Supply the W25Qxxx " Lee Jones
2014-03-20 9:21 ` [PATCH v6 34/36] mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct Lee Jones
2014-03-20 9:21 ` [PATCH v6 35/36] mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions Lee Jones
2014-03-20 9:21 ` [PATCH v6 36/36] ARM: STi: Add support for the FSM Serial Flash Controller Lee Jones
2014-03-20 11:27 ` Brian Norris
2014-03-20 15:51 ` Lee Jones
2014-03-20 9:48 ` [PATCH v6 00/36] mtd: st_spi_fsm: Add new driver Brian Norris
2014-03-20 11:19 ` Brian Norris
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1395307268-12721-2-git-send-email-lee.jones@linaro.org \
--to=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).