From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/4] mfd: twl4030-power: Add recommended idle configuration
Date: Wed, 23 Apr 2014 17:40:27 -0700 [thread overview]
Message-ID: <1398300030-7386-2-git-send-email-tony@atomide.com> (raw)
In-Reply-To: <1398300030-7386-1-git-send-email-tony@atomide.com>
These settings are based on the "Recommended Sleep Sequences for
the Zoom Platform" pdf at:
http://omappedia.com/wiki/File:Recommended_Sleep_Sequences_Zoom.pdf
These settings assume most of the regulators are under control of
Linux, and cuts off VDD1 and VDD2 during off-idle as Linux cannot
do it.
For any board specific changes to these, let's patch them in as
changes to the generic data in the follow-up patches. This keeps
the board specific changes small.
Note that this does not consider the twl5030 errata 27. That
can be added later on after it has been tested.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
.../devicetree/bindings/mfd/twl4030-power.txt | 4 +
drivers/mfd/twl4030-power.c | 165 +++++++++++++++++++++
2 files changed, 169 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
index b906116..bbd6603 100644
--- a/Documentation/devicetree/bindings/mfd/twl4030-power.txt
+++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt
@@ -8,10 +8,14 @@ Required properties:
- compatible : must be one of the following
"ti,twl4030-power"
"ti,twl4030-power-reset"
+ "ti,twl4030-power-idle"
The use of ti,twl4030-power-reset is recommended at least on
3530 that needs a special configuration for warm reset to work.
+When using ti,twl4030-power-idle, the TI recommended configuration
+for idle modes is loaded to the tlw4030 PMIC.
+
Optional properties:
- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or
SLEEP-to-OFF transition when the system poweroffs.
diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c
index 1db0560..89a8528 100644
--- a/drivers/mfd/twl4030-power.c
+++ b/drivers/mfd/twl4030-power.c
@@ -595,11 +595,176 @@ static struct twl4030_power_data omap3_reset = {
.resource_config = omap3_rconfig,
};
+/* Recommended generic default idle configuration for off-idle */
+
+/* Broadcast message to put res to sleep */
+static struct twl4030_ins omap3_idle_sleep_on_seq[] = {
+ { MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, RES_TYPE_ALL,
+ 0, RES_STATE_SLEEP), 2 },
+};
+
+static struct twl4030_script omap3_idle_sleep_on_script = {
+ .script = omap3_idle_sleep_on_seq,
+ .size = ARRAY_SIZE(omap3_idle_sleep_on_seq),
+ .flags = TWL4030_SLEEP_SCRIPT,
+};
+
+/* Broadcast message to put res to active */
+static struct twl4030_ins omap3_idle_wakeup_p12_seq[] = {
+ { MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, RES_TYPE_ALL,
+ 0, RES_STATE_ACTIVE), 2 },
+ };
+
+static struct twl4030_script omap3_idle_wakeup_p12_script = {
+ .script = omap3_idle_wakeup_p12_seq,
+ .size = ARRAY_SIZE(omap3_idle_wakeup_p12_seq),
+ .flags = TWL4030_WAKEUP12_SCRIPT,
+};
+
+/* Broadcast message to put res to active */
+static struct twl4030_ins omap3_idle_wakeup_p3_seq[] = {
+ { MSG_SINGULAR(DEV_GRP_NULL, RES_CLKEN, RES_STATE_ACTIVE), 0x37 },
+ { MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, RES_TYPE_ALL,
+ 0, RES_STATE_ACTIVE), 2 },
+};
+
+static struct twl4030_script omap3_idle_wakeup_p3_script = {
+ .script = omap3_idle_wakeup_p3_seq,
+ .size = ARRAY_SIZE(omap3_idle_wakeup_p3_seq),
+ .flags = TWL4030_WAKEUP3_SCRIPT,
+};
+
+static struct twl4030_script omap3_idle_wrst_script = {
+ .script = omap3_wrst_seq,
+ .size = ARRAY_SIZE(omap3_wrst_seq),
+ .flags = TWL4030_WRST_SCRIPT,
+};
+
+static struct twl4030_script *omap3_idle_scripts[] = {
+ &omap3_idle_wakeup_p12_script,
+ &omap3_idle_wakeup_p3_script,
+ &omap3_idle_wrst_script,
+ &omap3_idle_sleep_on_script,
+};
+
+/*
+ * Usable values for .remap_sleep and .remap_off
+ * Based on table "5.3.3 Resource Operating modes"
+ */
+enum {
+ TWL_REMAP_OFF = 0,
+ TWL_REMAP_SLEEP = 8,
+ TWL_REMAP_ACTIVE = 9,
+};
+
+#define TWL_DEV_GRP_P123 (DEV_GRP_P1 | DEV_GRP_P2 | DEV_GRP_P3)
+
+/*
+ * Recommended configuration based on "Recommended Sleep
+ * Sequences for the Zoom Platform":
+ * http://omappedia.com/wiki/File:Recommended_Sleep_Sequences_Zoom.pdf
+ */
+static struct twl4030_resconfig omap3_idle_rconfig[] = {
+ { .resource = RES_VAUX1, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VAUX2, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VAUX3, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VAUX4, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VMMC1, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VMMC2, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VPLL1, .devgroup = DEV_GRP_P1,
+ .type = 3, .type2 = 1, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_OFF, },
+ { .resource = RES_VPLL2, .devgroup = DEV_GRP_P1,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VSIM, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VDAC, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VINTANA1, .devgroup = TWL_DEV_GRP_P123,
+ .type = 1, .type2 = 2, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VINTANA2, .devgroup = TWL_DEV_GRP_P123,
+ .type = 0, .type2 = 2, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VINTDIG, .devgroup = TWL_DEV_GRP_P123,
+ .type = 1, .type2 = 2, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VIO, .devgroup = TWL_DEV_GRP_P123,
+ .type = 2, .type2 = 2, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VDD1, .devgroup = DEV_GRP_P1,
+ .type = 4, .type2 = 1, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_OFF, },
+ { .resource = RES_VDD2, .devgroup = DEV_GRP_P1,
+ .type = 3, .type2 = 1, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_OFF, },
+ { .resource = RES_VUSB_1V5, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VUSB_1V8, .devgroup = DEV_GRP_NULL,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_VUSB_3V1, .devgroup = TWL_DEV_GRP_P123,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ /* Resource #20 USB charge pump skipped */
+ { .resource = RES_REGEN, .devgroup = TWL_DEV_GRP_P123,
+ .type = 2, .type2 = 1, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_NRES_PWRON, .devgroup = TWL_DEV_GRP_P123,
+ .type = 0, .type2 = 1, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP },
+ { .resource = RES_CLKEN, .devgroup = TWL_DEV_GRP_P123,
+ .type = 3, .type2 = 2, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_SYSEN, .devgroup = TWL_DEV_GRP_P123,
+ .type = 6, .type2 = -1, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_HFCLKOUT, .devgroup = DEV_GRP_P3,
+ .type = 0, .type2 = 2, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_32KCLKOUT, .devgroup = TWL_DEV_GRP_P123,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_RESET, .devgroup = TWL_DEV_GRP_P123,
+ .type = 6, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { .resource = RES_MAIN_REF, .devgroup = TWL_DEV_GRP_P123,
+ .type = 0, .type2 = 0, .remap_off = TWL_REMAP_OFF,
+ .remap_sleep = TWL_REMAP_SLEEP, },
+ { /* Terminator */ },
+};
+
+static struct twl4030_power_data omap3_idle = {
+ .scripts = omap3_idle_scripts,
+ .num = ARRAY_SIZE(omap3_idle_scripts),
+ .resource_config = omap3_idle_rconfig,
+};
+
static struct of_device_id twl4030_power_of_match[] = {
{
.compatible = "ti,twl4030-power-reset",
.data = &omap3_reset,
},
+ {
+ .compatible = "ti,twl4030-power-idle",
+ .data = &omap3_idle,
+ },
{ },
};
MODULE_DEVICE_TABLE(of, twl4030_power_of_match);
--
1.8.1.1
next prev parent reply other threads:[~2014-04-24 0:40 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-04-24 0:40 [PATCH 0/4] mfd: twl4030-power: Enable off-idle configuration when booted with device tree Tony Lindgren
2014-04-24 0:40 ` Tony Lindgren [this message]
2014-04-28 11:41 ` [PATCH 1/4] mfd: twl4030-power: Add recommended idle configuration Lee Jones
2014-04-28 15:33 ` Tony Lindgren
2014-04-28 15:42 ` Lee Jones
2014-04-24 0:40 ` [PATCH 2/4] mfd: twl4030-power: Add support for board specific configuration Tony Lindgren
2014-04-28 11:47 ` Lee Jones
2014-04-28 15:36 ` Tony Lindgren
2014-04-24 0:40 ` [PATCH 3/4] mfd: twl4030power: Add a configuration to turn off oscillator during off-idle Tony Lindgren
2014-04-28 11:48 ` Lee Jones
2014-04-24 0:40 ` [PATCH 4/4] ARM: dts: Enable twl4030 off-idle configuration for selected omaps Tony Lindgren
2014-04-24 0:49 ` [PATCH 1a/4] mfd: twl4030-power: Add generic reset configuration Tony Lindgren
2014-04-28 11:37 ` Lee Jones
2014-04-28 16:01 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1398300030-7386-2-git-send-email-tony@atomide.com \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).