[PATCH 1/8] ARM: dts: imx27-phytec-phycore-rdk: Remove duplicate entries for USB PHY

[PATCH 1/8] ARM: dts: imx27-phytec-phycore-rdk: Remove duplicate entries for USB PHY

[Alexander Shiyan]

"compatible", "#address-cells" and "#size-cells" for USB PHY are
already described in the SOM DTS. Remove these duplicate entries.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
index 0875327..ac18ccf 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
@@ -39,10 +39,6 @@
 	};
 
 	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		usbphy2: usbphy at 2 {
 			compatible = "usb-nop-xceiv";
 			reg = <0>;
-- 
1.8.3.2

[PATCH 2/8] ARM: dts: imx27-phytec-phycore-som: Fix active level for FEC reset

[Alexander Shiyan]

FEC reset GPIO is active low. Fix this typo.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
index 32cc7dac9a..93482e9 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
@@ -182,7 +182,7 @@
 
 &fec {
 	phy-mode = "mii";
-	phy-reset-gpios = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+	phy-reset-gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
 	phy-supply = <&reg_3v3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
-- 
1.8.3.2

[PATCH 3/8] ARM: dts: imx27-phytec-phycore-som: Disable PM pins for USB OTG

[Alexander Shiyan]

USB PWR and OC pins are used as GPIOs for different purposes,
so add "disable-over-current" property for OTG node to indicate this.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
index 93482e9..b81796c 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
@@ -323,6 +323,7 @@
 	phy_type = "ulpi";
 	fsl,usbphy = <&usbphy0>;
 	vbus-supply = <&sw3_reg>;
+	disable-over-current;
 	status = "okay";
 };
 
-- 
1.8.3.2

[PATCH 4/8] ARM: dts: imx: Remove excess entries for PMIC

[Alexander Shiyan]

This patch removes excess "#address-cells" and "#size-cells" entries
for PMIC, since these entries is not used.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-pdk.dts                 | 2 --
 arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi | 2 --
 arch/arm/boot/dts/imx51-babbage.dts             | 2 --
 3 files changed, 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx27-pdk.dts b/arch/arm/boot/dts/imx27-pdk.dts
index 764cf79..4c31771 100644
--- a/arch/arm/boot/dts/imx27-pdk.dts
+++ b/arch/arm/boot/dts/imx27-pdk.dts
@@ -42,8 +42,6 @@
 	status = "okay";
 
 	pmic: mc13783 at 0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
 		compatible = "fsl,mc13783";
 		reg = <0>;
 		spi-cs-high;
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
index b81796c..31e9f70 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
@@ -80,8 +80,6 @@
 	status = "okay";
 
 	pmic: mc13783 at 0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
 		compatible = "fsl,mc13783";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts
index e9ce0c0..89470bf 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/imx51-babbage.dts
@@ -191,8 +191,6 @@
 	status = "okay";
 
 	pmic: mc13892 at 0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
 		compatible = "fsl,mc13892";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;
-- 
1.8.3.2

[PATCH 5/8] ARM: dts: imx27-phytec-phycore-rdk: Add CSI enable switch

[Alexander Shiyan]

This patch adds a GPIO fixed regulator which used on RDK to
enable CSI bus.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
index ac18ccf..72c773e 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
@@ -38,6 +38,20 @@
 		};
 	};
 
+	regulators {
+		regulator at 2 {
+			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_csien>;
+			reg = <2>;
+			regulator-name = "CSI_EN";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
+			regulator-always-on;
+		};
+	};
+
 	usbphy {
 		usbphy2: usbphy at 2 {
 			compatible = "usb-nop-xceiv";
@@ -83,6 +97,12 @@
 
 &iomuxc {
 	imx27_phycore_rdk {
+		pinctrl_csien: csiengrp {
+			fsl,pins = <
+				MX27_PAD_USB_OC_B__GPIO2_24 0x0
+			>;
+		};
+
 		pinctrl_cspi1cs1: cspi1cs1grp {
 			fsl,pins = <
 				MX27_PAD_CSPI1_SS1__GPIO4_27 0x0
-- 
1.8.3.2

[PATCH 6/8] ARM: dts: imx27-phytec-phycore-rdk: Fix "reg" property for USBH2 PHY

[Alexander Shiyan]

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
index 72c773e..d0b693f 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
@@ -55,7 +55,7 @@
 	usbphy {
 		usbphy2: usbphy at 2 {
 			compatible = "usb-nop-xceiv";
-			reg = <0>;
+			reg = <2>;
 			vcc-supply = <&reg_5v0>;
 			clocks = <&clks 0>;
 			clock-names = "main_clk";
-- 
1.8.3.2

[PATCH 7/8] ARM: dts: imx27: Trim node name for FEC

[Alexander Shiyan]

This patch reduce node name for FEC. Otherwise, the name for PHY
is composed incorrectly.

Before:
fec 1002b000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.etherne:00, irq=-1)

After:
fec 1002b000.fec eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.fec-1:00, irq=-1)

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
index a75555c..377339e 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/imx27.dtsi
@@ -497,7 +497,7 @@
 				clocks = <&clks 38>;
 			};
 
-			fec: ethernet at 1002b000 {
+			fec: fec at 1002b000 {
 				compatible = "fsl,imx27-fec";
 				reg = <0x1002b000 0x4000>;
 				interrupts = <50>;
-- 
1.8.3.2

[PATCH 8/8] ARM: dts: imx27-phytec-phycore-*: Move "iomux" node to the bottom of file

[Alexander Shiyan]

This patch moves "iomux" node to the bottom of file.
No functional changes.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts  | 234 ++++++++++++------------
 arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi | 176 +++++++++---------
 2 files changed, 205 insertions(+), 205 deletions(-)

diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
index d0b693f..07de457 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
@@ -95,123 +95,6 @@
 	};
 };
 
-&iomuxc {
-	imx27_phycore_rdk {
-		pinctrl_csien: csiengrp {
-			fsl,pins = <
-				MX27_PAD_USB_OC_B__GPIO2_24 0x0
-			>;
-		};
-
-		pinctrl_cspi1cs1: cspi1cs1grp {
-			fsl,pins = <
-				MX27_PAD_CSPI1_SS1__GPIO4_27 0x0
-			>;
-		};
-
-		pinctrl_imxfb1: imxfbgrp {
-			fsl,pins = <
-				MX27_PAD_LD0__LD0 0x0
-				MX27_PAD_LD1__LD1 0x0
-				MX27_PAD_LD2__LD2 0x0
-				MX27_PAD_LD3__LD3 0x0
-				MX27_PAD_LD4__LD4 0x0
-				MX27_PAD_LD5__LD5 0x0
-				MX27_PAD_LD6__LD6 0x0
-				MX27_PAD_LD7__LD7 0x0
-				MX27_PAD_LD8__LD8 0x0
-				MX27_PAD_LD9__LD9 0x0
-				MX27_PAD_LD10__LD10 0x0
-				MX27_PAD_LD11__LD11 0x0
-				MX27_PAD_LD12__LD12 0x0
-				MX27_PAD_LD13__LD13 0x0
-				MX27_PAD_LD14__LD14 0x0
-				MX27_PAD_LD15__LD15 0x0
-				MX27_PAD_LD16__LD16 0x0
-				MX27_PAD_LD17__LD17 0x0
-				MX27_PAD_CLS__CLS 0x0
-				MX27_PAD_CONTRAST__CONTRAST 0x0
-				MX27_PAD_LSCLK__LSCLK 0x0
-				MX27_PAD_OE_ACD__OE_ACD 0x0
-				MX27_PAD_PS__PS 0x0
-				MX27_PAD_REV__REV 0x0
-				MX27_PAD_SPL_SPR__SPL_SPR 0x0
-				MX27_PAD_HSYNC__HSYNC 0x0
-				MX27_PAD_VSYNC__VSYNC 0x0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			/* Add pullup to DATA line */
-			fsl,pins = <
-				MX27_PAD_I2C_DATA__I2C_DATA	0x1
-				MX27_PAD_I2C_CLK__I2C_CLK	0x0
-			>;
-		};
-
-		pinctrl_owire1: owire1grp {
-			fsl,pins = <
-				MX27_PAD_RTCK__OWIRE 0x0
-			>;
-		};
-
-		pinctrl_sdhc2: sdhc2grp {
-			fsl,pins = <
-				MX27_PAD_SD2_CLK__SD2_CLK 0x0
-				MX27_PAD_SD2_CMD__SD2_CMD 0x0
-				MX27_PAD_SD2_D0__SD2_D0 0x0
-				MX27_PAD_SD2_D1__SD2_D1 0x0
-				MX27_PAD_SD2_D2__SD2_D2 0x0
-				MX27_PAD_SD2_D3__SD2_D3 0x0
-				MX27_PAD_SSI3_FS__GPIO3_28	0x0 /* WP */
-				MX27_PAD_SSI3_RXDAT__GPIO3_29	0x0 /* CD */
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX27_PAD_UART1_TXD__UART1_TXD 0x0
-				MX27_PAD_UART1_RXD__UART1_RXD 0x0
-				MX27_PAD_UART1_CTS__UART1_CTS 0x0
-				MX27_PAD_UART1_RTS__UART1_RTS 0x0
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX27_PAD_UART2_TXD__UART2_TXD 0x0
-				MX27_PAD_UART2_RXD__UART2_RXD 0x0
-				MX27_PAD_UART2_CTS__UART2_CTS 0x0
-				MX27_PAD_UART2_RTS__UART2_RTS 0x0
-			>;
-		};
-
-		pinctrl_usbh2: usbh2grp {
-			fsl,pins = <
-				MX27_PAD_USBH2_CLK__USBH2_CLK 0x0
-				MX27_PAD_USBH2_DIR__USBH2_DIR 0x0
-				MX27_PAD_USBH2_NXT__USBH2_NXT 0x0
-				MX27_PAD_USBH2_STP__USBH2_STP 0x0
-				MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x0
-				MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x0
-				MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x0
-				MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x0
-				MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x0
-				MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x0
-				MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x0
-				MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x0
-			>;
-		};
-
-		pinctrl_weim: weimgrp {
-			fsl,pins = <
-				MX27_PAD_CS4_B__CS4_B		0x0 /* CS4 */
-				MX27_PAD_SD1_D1__GPIO5_19	0x0 /* CAN IRQ */
-			>;
-		};
-	};
-};
-
 &owire {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_owire1>;
@@ -318,3 +201,120 @@
 		fsl,weim-cs-timing = <0x0000dcf6 0x444a0301 0x44443302>;
 	};
 };
+
+&iomuxc {
+	imx27_phycore_rdk {
+		pinctrl_csien: csiengrp {
+			fsl,pins = <
+				MX27_PAD_USB_OC_B__GPIO2_24		0x0
+			>;
+		};
+
+		pinctrl_cspi1cs1: cspi1cs1grp {
+			fsl,pins = <
+				MX27_PAD_CSPI1_SS1__GPIO4_27		0x0
+			>;
+		};
+
+		pinctrl_imxfb1: imxfbgrp {
+			fsl,pins = <
+				MX27_PAD_LD0__LD0			0x0
+				MX27_PAD_LD1__LD1			0x0
+				MX27_PAD_LD2__LD2			0x0
+				MX27_PAD_LD3__LD3			0x0
+				MX27_PAD_LD4__LD4			0x0
+				MX27_PAD_LD5__LD5			0x0
+				MX27_PAD_LD6__LD6			0x0
+				MX27_PAD_LD7__LD7			0x0
+				MX27_PAD_LD8__LD8			0x0
+				MX27_PAD_LD9__LD9			0x0
+				MX27_PAD_LD10__LD10			0x0
+				MX27_PAD_LD11__LD11			0x0
+				MX27_PAD_LD12__LD12			0x0
+				MX27_PAD_LD13__LD13			0x0
+				MX27_PAD_LD14__LD14			0x0
+				MX27_PAD_LD15__LD15			0x0
+				MX27_PAD_LD16__LD16			0x0
+				MX27_PAD_LD17__LD17			0x0
+				MX27_PAD_CLS__CLS			0x0
+				MX27_PAD_CONTRAST__CONTRAST		0x0
+				MX27_PAD_LSCLK__LSCLK			0x0
+				MX27_PAD_OE_ACD__OE_ACD			0x0
+				MX27_PAD_PS__PS				0x0
+				MX27_PAD_REV__REV			0x0
+				MX27_PAD_SPL_SPR__SPL_SPR		0x0
+				MX27_PAD_HSYNC__HSYNC			0x0
+				MX27_PAD_VSYNC__VSYNC			0x0
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			/* Use pullup for DATA line */
+			fsl,pins = <
+				MX27_PAD_I2C_DATA__I2C_DATA		0x1
+				MX27_PAD_I2C_CLK__I2C_CLK		0x0
+			>;
+		};
+
+		pinctrl_owire1: owire1grp {
+			fsl,pins = <
+				MX27_PAD_RTCK__OWIRE			0x0
+			>;
+		};
+
+		pinctrl_sdhc2: sdhc2grp {
+			fsl,pins = <
+				MX27_PAD_SD2_CLK__SD2_CLK		0x0
+				MX27_PAD_SD2_CMD__SD2_CMD		0x0
+				MX27_PAD_SD2_D0__SD2_D0			0x0
+				MX27_PAD_SD2_D1__SD2_D1			0x0
+				MX27_PAD_SD2_D2__SD2_D2			0x0
+				MX27_PAD_SD2_D3__SD2_D3			0x0
+				MX27_PAD_SSI3_FS__GPIO3_28		0x0 /* WP */
+				MX27_PAD_SSI3_RXDAT__GPIO3_29		0x0 /* CD */
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX27_PAD_UART1_TXD__UART1_TXD		0x0
+				MX27_PAD_UART1_RXD__UART1_RXD		0x0
+				MX27_PAD_UART1_CTS__UART1_CTS		0x0
+				MX27_PAD_UART1_RTS__UART1_RTS		0x0
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX27_PAD_UART2_TXD__UART2_TXD		0x0
+				MX27_PAD_UART2_RXD__UART2_RXD		0x0
+				MX27_PAD_UART2_CTS__UART2_CTS		0x0
+				MX27_PAD_UART2_RTS__UART2_RTS		0x0
+			>;
+		};
+
+		pinctrl_usbh2: usbh2grp {
+			fsl,pins = <
+				MX27_PAD_USBH2_CLK__USBH2_CLK		0x0
+				MX27_PAD_USBH2_DIR__USBH2_DIR		0x0
+				MX27_PAD_USBH2_NXT__USBH2_NXT		0x0
+				MX27_PAD_USBH2_STP__USBH2_STP		0x0
+				MX27_PAD_CSPI2_SCLK__USBH2_DATA0	0x0
+				MX27_PAD_CSPI2_MOSI__USBH2_DATA1	0x0
+				MX27_PAD_CSPI2_MISO__USBH2_DATA2	0x0
+				MX27_PAD_CSPI2_SS1__USBH2_DATA3		0x0
+				MX27_PAD_CSPI2_SS2__USBH2_DATA4		0x0
+				MX27_PAD_CSPI1_SS2__USBH2_DATA5		0x0
+				MX27_PAD_CSPI2_SS0__USBH2_DATA6		0x0
+				MX27_PAD_USBH2_DATA7__USBH2_DATA7	0x0
+			>;
+		};
+
+		pinctrl_weim: weimgrp {
+			fsl,pins = <
+				MX27_PAD_CS4_B__CS4_B			0x0 /* CS4 */
+				MX27_PAD_SD1_D1__GPIO5_19		0x0 /* CAN IRQ */
+			>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
index 31e9f70..1509f00 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
@@ -210,94 +210,6 @@
 	};
 };
 
-&iomuxc {
-	imx27_phycore_som {
-		pinctrl_cspi1: cspi1grp {
-			fsl,pins = <
-				MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x0
-				MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x0
-				MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x0
-				MX27_PAD_CSPI1_SS0__GPIO4_28	0x0 /* SPI1 CS0 */
-			>;
-		};
-
-		pinctrl_fec1: fec1grp {
-			fsl,pins = <
-				MX27_PAD_SD3_CMD__FEC_TXD0 0x0
-				MX27_PAD_SD3_CLK__FEC_TXD1 0x0
-				MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
-				MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
-				MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
-				MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
-				MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
-				MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
-				MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
-				MX27_PAD_ATA_DATA7__FEC_MDC 0x0
-				MX27_PAD_ATA_DATA8__FEC_CRS 0x0
-				MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
-				MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
-				MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
-				MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
-				MX27_PAD_ATA_DATA13__FEC_COL 0x0
-				MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
-				MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
-				MX27_PAD_SSI3_TXDAT__GPIO3_30	0x0 /* FEC RST */
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
-				MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
-			>;
-		};
-
-		pinctrl_nfc: nfcgrp {
-			fsl,pins = <
-				MX27_PAD_NFRB__NFRB 0x0
-				MX27_PAD_NFCLE__NFCLE 0x0
-				MX27_PAD_NFWP_B__NFWP_B 0x0
-				MX27_PAD_NFCE_B__NFCE_B 0x0
-				MX27_PAD_NFALE__NFALE 0x0
-				MX27_PAD_NFRE_B__NFRE_B 0x0
-				MX27_PAD_NFWE_B__NFWE_B 0x0
-			>;
-		};
-
-		pinctrl_pmic: pmicgrp {
-			fsl,pins = <
-				MX27_PAD_USB_PWR__GPIO2_23	0x0 /* PMIC IRQ */
-			>;
-		};
-
-		pinctrl_ssi1: ssi1grp {
-			fsl,pins = <
-				MX27_PAD_SSI1_FS__SSI1_FS 0x0
-				MX27_PAD_SSI1_RXDAT__SSI1_RXDAT 0x0
-				MX27_PAD_SSI1_TXDAT__SSI1_TXDAT 0x0
-				MX27_PAD_SSI1_CLK__SSI1_CLK 0x0
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x0
-				MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x0
-				MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x0
-				MX27_PAD_USBOTG_STP__USBOTG_STP 0x0
-				MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x0
-				MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x0
-				MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x0
-				MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x0
-				MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x0
-				MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x0
-				MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x0
-				MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x0
-			>;
-		};
-	};
-};
-
 &nfc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_nfc>;
@@ -348,3 +260,91 @@
 		#size-cells = <1>;
 	};
 };
+
+&iomuxc {
+	imx27_phycore_som {
+		pinctrl_cspi1: cspi1grp {
+			fsl,pins = <
+				MX27_PAD_CSPI1_MISO__CSPI1_MISO		0x0
+				MX27_PAD_CSPI1_MOSI__CSPI1_MOSI		0x0
+				MX27_PAD_CSPI1_SCLK__CSPI1_SCLK		0x0
+				MX27_PAD_CSPI1_SS0__GPIO4_28		0x0 /* SPI1 CS0 */
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				MX27_PAD_SD3_CMD__FEC_TXD0		0x0
+				MX27_PAD_SD3_CLK__FEC_TXD1		0x0
+				MX27_PAD_ATA_DATA0__FEC_TXD2		0x0
+				MX27_PAD_ATA_DATA1__FEC_TXD3		0x0
+				MX27_PAD_ATA_DATA2__FEC_RX_ER		0x0
+				MX27_PAD_ATA_DATA3__FEC_RXD1		0x0
+				MX27_PAD_ATA_DATA4__FEC_RXD2		0x0
+				MX27_PAD_ATA_DATA5__FEC_RXD3		0x0
+				MX27_PAD_ATA_DATA6__FEC_MDIO		0x0
+				MX27_PAD_ATA_DATA7__FEC_MDC		0x0
+				MX27_PAD_ATA_DATA8__FEC_CRS		0x0
+				MX27_PAD_ATA_DATA9__FEC_TX_CLK		0x0
+				MX27_PAD_ATA_DATA10__FEC_RXD0		0x0
+				MX27_PAD_ATA_DATA11__FEC_RX_DV		0x0
+				MX27_PAD_ATA_DATA12__FEC_RX_CLK		0x0
+				MX27_PAD_ATA_DATA13__FEC_COL		0x0
+				MX27_PAD_ATA_DATA14__FEC_TX_ER		0x0
+				MX27_PAD_ATA_DATA15__FEC_TX_EN		0x0
+				MX27_PAD_SSI3_TXDAT__GPIO3_30		0x0 /* FEC RST */
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX27_PAD_I2C2_SDA__I2C2_SDA		0x0
+				MX27_PAD_I2C2_SCL__I2C2_SCL		0x0
+			>;
+		};
+
+		pinctrl_nfc: nfcgrp {
+			fsl,pins = <
+				MX27_PAD_NFRB__NFRB			0x0
+				MX27_PAD_NFCLE__NFCLE			0x0
+				MX27_PAD_NFWP_B__NFWP_B			0x0
+				MX27_PAD_NFCE_B__NFCE_B			0x0
+				MX27_PAD_NFALE__NFALE			0x0
+				MX27_PAD_NFRE_B__NFRE_B			0x0
+				MX27_PAD_NFWE_B__NFWE_B			0x0
+			>;
+		};
+
+		pinctrl_pmic: pmicgrp {
+			fsl,pins = <
+				MX27_PAD_USB_PWR__GPIO2_23		0x0 /* PMIC IRQ */
+			>;
+		};
+
+		pinctrl_ssi1: ssi1grp {
+			fsl,pins = <
+				MX27_PAD_SSI1_FS__SSI1_FS		0x0
+				MX27_PAD_SSI1_RXDAT__SSI1_RXDAT		0x0
+				MX27_PAD_SSI1_TXDAT__SSI1_TXDAT		0x0
+				MX27_PAD_SSI1_CLK__SSI1_CLK		0x0
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX27_PAD_USBOTG_CLK__USBOTG_CLK		0x0
+				MX27_PAD_USBOTG_DIR__USBOTG_DIR		0x0
+				MX27_PAD_USBOTG_NXT__USBOTG_NXT		0x0
+				MX27_PAD_USBOTG_STP__USBOTG_STP		0x0
+				MX27_PAD_USBOTG_DATA0__USBOTG_DATA0	0x0
+				MX27_PAD_USBOTG_DATA1__USBOTG_DATA1	0x0
+				MX27_PAD_USBOTG_DATA2__USBOTG_DATA2	0x0
+				MX27_PAD_USBOTG_DATA3__USBOTG_DATA3	0x0
+				MX27_PAD_USBOTG_DATA4__USBOTG_DATA4	0x0
+				MX27_PAD_USBOTG_DATA5__USBOTG_DATA5	0x0
+				MX27_PAD_USBOTG_DATA6__USBOTG_DATA6	0x0
+				MX27_PAD_USBOTG_DATA7__USBOTG_DATA7	0x0
+			>;
+		};
+	};
+};
-- 
1.8.3.2

[PATCH 7/8] ARM: dts: imx27: Trim node name for FEC

[Sergei Shtylyov]

Hello.

On 26-04-2014 8:52, Alexander Shiyan wrote:

> This patch reduce node name for FEC. Otherwise, the name for PHY
> is composed incorrectly.

> Before:
> fec 1002b000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.etherne:00, irq=-1)

> After:
> fec 1002b000.fec eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.fec-1:00, irq=-1)

> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
> ---
>   arch/arm/boot/dts/imx27.dtsi | 2 +-
>   1 file changed, 1 insertion(+), 1 deletion(-)

> diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
> index a75555c..377339e 100644
> --- a/arch/arm/boot/dts/imx27.dtsi
> +++ b/arch/arm/boot/dts/imx27.dtsi
> @@ -497,7 +497,7 @@
>   				clocks = <&clks 38>;
>   			};
>
> -			fec: ethernet at 1002b000 {
> +			fec: fec at 1002b000 {

    The "ethernet" name complies to the ePAPR standard. Don't change it, please.

WBR, Sergei

Re: [PATCH 7/8] ARM: dts: imx27: Trim node name for FEC

[Alexander Shiyan]

Sat, 26 Apr 2014 20:32:18 +0400 ?? Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>:
> Hello.
> 
> On 26-04-2014 8:52, Alexander Shiyan wrote:
> 
> > This patch reduce node name for FEC. Otherwise, the name for PHY
> > is composed incorrectly.
> 
> > Before:
> > fec 1002b000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.etherne:00, irq=-1)
> 
> > After:
> > fec 1002b000.fec eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.fec-1:00, irq=-1)
> 
> > Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
> > ---
> >   arch/arm/boot/dts/imx27.dtsi | 2 +-
> >   1 file changed, 1 insertion(+), 1 deletion(-)
> 
> > diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
> > index a75555c..377339e 100644
> > --- a/arch/arm/boot/dts/imx27.dtsi
> > +++ b/arch/arm/boot/dts/imx27.dtsi
> > @@ -497,7 +497,7 @@
> >   				clocks = <&clks 38>;
> >   			};
> >
> > -			fec: ethernet at 1002b000 {
> > +			fec: fec at 1002b000 {
> 
>     The "ethernet" name complies to the ePAPR standard. Don't change it, please.

So this is ok?
mii_bus:phy_addr=1002b000.etherne:00

---

[PATCH 7/8] ARM: dts: imx27: Trim node name for FEC

[Sergei Shtylyov]

Hello.

On 26-04-2014 20:39, Alexander Shiyan wrote:

>>> This patch reduce node name for FEC. Otherwise, the name for PHY
>>> is composed incorrectly.

>>> Before:
>>> fec 1002b000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.etherne:00, irq=-1)

>>> After:
>>> fec 1002b000.fec eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.fec-1:00, irq=-1)

>>> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
>>> ---
>>>    arch/arm/boot/dts/imx27.dtsi | 2 +-
>>>    1 file changed, 1 insertion(+), 1 deletion(-)

>>> diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
>>> index a75555c..377339e 100644
>>> --- a/arch/arm/boot/dts/imx27.dtsi
>>> +++ b/arch/arm/boot/dts/imx27.dtsi
>>> @@ -497,7 +497,7 @@
>>>    				clocks = <&clks 38>;
>>>    			};
>>>
>>> -			fec: ethernet at 1002b000 {
>>> +			fec: fec at 1002b000 {

>>      The "ethernet" name complies to the ePAPR standard. Don't change it, please.

> So this is ok?
> mii_bus:phy_addr=1002b000.etherne:00

    Why not? :-)

WBR, Sergei

Re: [PATCH 7/8] ARM: dts: imx27: Trim node name for FEC

[Alexander Shiyan]

Sat, 26 Apr 2014 20:54:11 +0400 ?? Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>:
> Hello.
> 
> On 26-04-2014 20:39, Alexander Shiyan wrote:
> 
> >>> This patch reduce node name for FEC. Otherwise, the name for PHY
> >>> is composed incorrectly.
> 
> >>> Before:
> >>> fec 1002b000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.etherne:00, irq=-1)
> 
> >>> After:
> >>> fec 1002b000.fec eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1002b000.fec-1:00, irq=-1)
> 
> >>> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
> >>> ---
> >>>    arch/arm/boot/dts/imx27.dtsi | 2 +-
> >>>    1 file changed, 1 insertion(+), 1 deletion(-)
> 
> >>> diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
> >>> index a75555c..377339e 100644
> >>> --- a/arch/arm/boot/dts/imx27.dtsi
> >>> +++ b/arch/arm/boot/dts/imx27.dtsi
> >>> @@ -497,7 +497,7 @@
> >>>    				clocks = <&clks 38>;
> >>>    			};
> >>>
> >>> -			fec: ethernet at 1002b000 {
> >>> +			fec: fec at 1002b000 {
> 
> >>      The "ethernet" name complies to the ePAPR standard. Don't change it, please.
> 
> > So this is ok?
> > mii_bus:phy_addr=1002b000.etherne:00
> 
>     Why not? :-)

OK if so. Shawn, please skip this one patch if all other looks OK.

---

[PATCH 8/8] ARM: dts: imx27-phytec-phycore-*: Move "iomux" node to the bottom of file

[Sascha Hauer]

On Sat, Apr 26, 2014 at 08:52:13AM +0400, Alexander Shiyan wrote:
> This patch moves "iomux" node to the bottom of file.
> No functional changes.

Why? The nodes are (at least should be) sorted alphabetically.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH 8/8] ARM: dts: imx27-phytec-phycore-*: Move "iomux" node to the bottom of file

[Alexander Shiyan]

Sat, 26 Apr 2014 21:09:35 +0200 ?? Sascha Hauer <s.hauer@pengutronix.de>:
> On Sat, Apr 26, 2014 at 08:52:13AM +0400, Alexander Shiyan wrote:
> > This patch moves "iomux" node to the bottom of file.
> > No functional changes.
> 
> Why? The nodes are (at least should be) sorted alphabetically.

Pin definitions look better in one place, at the bottom.
As far as I know, Shawn supported this position.

---

[PATCH 8/8] ARM: dts: imx27-phytec-phycore-*: Move "iomux" node to the bottom of file

[Sascha Hauer]

On Sat, Apr 26, 2014 at 11:15:10PM +0400, Alexander Shiyan wrote:
> Sat, 26 Apr 2014 21:09:35 +0200 ?? Sascha Hauer <s.hauer@pengutronix.de>:
> > On Sat, Apr 26, 2014 at 08:52:13AM +0400, Alexander Shiyan wrote:
> > > This patch moves "iomux" node to the bottom of file.
> > > No functional changes.
> > 
> > Why? The nodes are (at least should be) sorted alphabetically.
> 
> Pin definitions look better in one place, at the bottom.
> As far as I know, Shawn supported this position.

If that's the way we want to go then ok. I wasn't aware of this.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH 8/8] ARM: dts: imx27-phytec-phycore-*: Move "iomux" node to the bottom of file

[Shawn Guo]

On Sat, Apr 26, 2014 at 08:52:13AM +0400, Alexander Shiyan wrote:
> This patch moves "iomux" node to the bottom of file.

Let's only do this for new files, and save the churn on the existing
files.

Shawn

> No functional changes.
> 
> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
> ---
>  arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts  | 234 ++++++++++++------------
>  arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi | 176 +++++++++---------
>  2 files changed, 205 insertions(+), 205 deletions(-)

[PATCH 1/8] ARM: dts: imx27-phytec-phycore-rdk: Remove duplicate entries for USB PHY

[Shawn Guo]

On Sat, Apr 26, 2014 at 08:52:06AM +0400, Alexander Shiyan wrote:
> "compatible", "#address-cells" and "#size-cells" for USB PHY are
> already described in the SOM DTS. Remove these duplicate entries.
> 
> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>

Applied 1 ~ 6, thanks.