From: acourbot@nvidia.com (Alexandre Courbot)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2] ARM: tegra: add Tegra Note 7 device tree
Date: Fri, 2 May 2014 16:59:08 +0900 [thread overview]
Message-ID: <1399017548-1638-1-git-send-email-acourbot@nvidia.com> (raw)
Tegra Note 7 is a consumer tablet embedding a Tegra 4 SoC with 1GB RAM
and a 720p panel.
The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, DSI panel, keys.
SD card, HDMI, charger, self-powered USB, audio, wifi, bluetooth are not
yet supported but might be by future patches (likely in that order).
Touch panel, sensors & cameras will probably never be supported.
Pinctrl is not set yet, as the bootloader-provided values allow us to
use the currently supported hardware.
Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the bootloader
which is filled with garbage.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[treding at nvidia.com: DT fixes, DSI panel support]
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes since v1:
- removed the cma kernel parameter
- removed the not-yet-working HDMI node
- do not keep some non-essential regulators always on
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/tegra114-tn7.dts | 348 +++++++++++++++++++++++++++++++++++++
2 files changed, 349 insertions(+)
create mode 100644 arch/arm/boot/dts/tegra114-tn7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 49717b2db19a..fb662207a504 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -369,6 +369,7 @@ dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
tegra30-cardhu-a02.dtb \
tegra30-cardhu-a04.dtb \
tegra114-dalmore.dtb \
+ tegra114-tn7.dtb \
tegra124-jetson-tk1.dtb \
tegra124-venice2.dtb
dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb
diff --git a/arch/arm/boot/dts/tegra114-tn7.dts b/arch/arm/boot/dts/tegra114-tn7.dts
new file mode 100644
index 000000000000..963662145635
--- /dev/null
+++ b/arch/arm/boot/dts/tegra114-tn7.dts
@@ -0,0 +1,348 @@
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "tegra114.dtsi"
+
+/ {
+ model = "Tegra Note 7";
+ compatible = "nvidia,tn7", "nvidia,tegra114";
+
+ chosen {
+ /* TN7's bootloader's arguments need to be overridden */
+ bootargs = "console=ttyS0,115200n8 console=tty1 gpt fbcon=rotate:2";
+ /* TN7's bootloader will place initrd at this address */
+ linux,initrd-start = <0x82000000>;
+ linux,initrd-end = <0x82800000>;
+ };
+
+ firmware {
+ trusted-foundations {
+ compatible = "tlm,trusted-foundations";
+ tlm,version-major = <2>;
+ tlm,version-minor = <8>;
+ };
+ };
+
+ memory {
+ /* memory >= 0x37e00000 is reserved for firmware usage */
+ reg = <0x80000000 0x37e00000>;
+ };
+
+ host1x at 50000000 {
+ dsi at 54300000 {
+ status = "okay";
+
+ vdd-supply = <&vdd_1v2_ap>;
+
+ panel at 0 {
+ compatible = "lg,ld070wx3-sl01";
+ reg = <0>;
+
+ power-supply = <&vdd_lcd>;
+ backlight = <&backlight>;
+ };
+ };
+ };
+
+ serial at 70006300 {
+ status = "okay";
+ };
+
+ pwm at 7000a000 {
+ status = "okay";
+ };
+
+ i2c at 7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ palmas: pmic at 58 {
+ compatible = "ti,palmas";
+ reg = <0x58>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_LOW>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ ti,system-power-controller;
+
+ palmas_gpio: gpio {
+ compatible = "ti,palmas-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pmic {
+ compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+
+ ldoln-in-supply = <&vdd_smps10_out2>;
+
+ regulators {
+ smps123 {
+ regulator-name = "vd-cpu";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps45 {
+ regulator-name = "vd-soc";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps6 {
+ regulator-name = "va-lcd-hv";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps7 {
+ regulator-name = "vd-ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_1v8: smps8 {
+ regulator-name = "vs-pmu-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_2v9_sys: smps9 {
+ regulator-name = "vs-sys-2v9";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_smps10_out1: smps10_out1 {
+ regulator-name = "vd-smps10-out1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_smps10_out2: smps10_out2 {
+ regulator-name = "vd-smps10-out2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo1 {
+ regulator-name = "va-pllx";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_1v2_ap: ldo2 {
+ regulator-name = "va-ap-1v2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo3 {
+ regulator-name = "vd-fuse";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4 {
+ regulator-name = "vd-ts-hv";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo5 {
+ regulator-name = "va-cam2-hv";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ ldo6 {
+ regulator-name = "va-sns-hv";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ ldo7 {
+ regulator-name = "va-cam1-hv";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ ldo8 {
+ regulator-name = "va-ap-rtc";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ ti,enable-ldo8-tracking;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo9 {
+ regulator-name = "vi-sdcard";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ ldousb {
+ regulator-name = "avdd-usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldoln {
+ regulator-name = "va-hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ rtc {
+ compatible = "ti,palmas-rtc";
+ interrupt-parent = <&palmas>;
+ interrupts = <8 0>;
+ };
+
+ };
+ };
+
+ pmc at 7000e400 {
+ nvidia,invert-interrupt;
+ };
+
+ /* eMMC */
+ sdhci at 78000600 {
+ status = "okay";
+ bus-width = <8>;
+ vmmc-supply = <&vdd_1v8>;
+ non-removable;
+ };
+
+ usb at 7d000000 {
+ status = "okay";
+ };
+
+ usb-phy at 7d000000 {
+ status = "okay";
+ nvidia,xcvr-setup = <7>;
+ nvidia,xcvr-lsfslew = <2>;
+ nvidia,xcvr-lsrslew = <2>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ /* Should be changed to "otg" once we have vbus_supply */
+ /* As of now, USB devices need to be powered externally */
+ dr_mode = "host";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 1 40000>;
+
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+
+ power-supply = <&lcd_bl_en>;
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clk32k_in: clock {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+
+ volume_down {
+ label = "Volume Down";
+ gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ volume_up {
+ label = "Volume Up";
+ gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* FIXME: output of BQ24192 */
+ vs_sys: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "VS_SYS";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ lcd_bl_en: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "VDD_LCD_BL";
+ regulator-min-microvolt = <16500000>;
+ regulator-max-microvolt = <16500000>;
+ gpio = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vs_sys>;
+ regulator-boot-on;
+ };
+
+ vdd_lcd: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "VD_LCD_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&palmas_gpio 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&vdd_1v8>;
+ regulator-boot-on;
+ };
+ };
+};
--
1.9.2
next reply other threads:[~2014-05-02 7:59 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-02 7:59 Alexandre Courbot [this message]
2014-05-02 18:20 ` [PATCH v2] ARM: tegra: add Tegra Note 7 device tree Stephen Warren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1399017548-1638-1-git-send-email-acourbot@nvidia.com \
--to=acourbot@nvidia.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).