* [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
@ 2014-05-27 12:53 Lee Jones
2014-05-27 18:01 ` Olof Johansson
2014-06-25 14:53 ` Lee Jones
0 siblings, 2 replies; 6+ messages in thread
From: Lee Jones @ 2014-05-27 12:53 UTC (permalink / raw)
To: linux-arm-kernel
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
arch/arm/boot/dts/stih415-pinctrl.dtsi | 340 +++++++++++++++---------------
arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
arch/arm/boot/dts/stih416-pinctrl.dtsi | 342 +++++++++++++++----------------
arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +-
5 files changed, 350 insertions(+), 350 deletions(-)
diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
index caeac7e..1e0255d 100644
--- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
@@ -11,33 +11,33 @@
/ {
aliases {
- gpio0 = &PIO0;
- gpio1 = &PIO1;
- gpio2 = &PIO2;
- gpio3 = &PIO3;
- gpio4 = &PIO4;
- gpio5 = &PIO5;
- gpio6 = &PIO6;
- gpio7 = &PIO7;
- gpio8 = &PIO8;
- gpio9 = &PIO9;
- gpio10 = &PIO10;
- gpio11 = &PIO11;
- gpio12 = &PIO12;
- gpio13 = &PIO13;
- gpio14 = &PIO14;
- gpio15 = &PIO15;
- gpio16 = &PIO16;
- gpio17 = &PIO17;
- gpio18 = &PIO18;
- gpio19 = &PIO100;
- gpio20 = &PIO101;
- gpio21 = &PIO102;
- gpio22 = &PIO103;
- gpio23 = &PIO104;
- gpio24 = &PIO105;
- gpio25 = &PIO106;
- gpio26 = &PIO107;
+ gpio0 = &pio0;
+ gpio1 = &pio1;
+ gpio2 = &pio2;
+ gpio3 = &pio3;
+ gpio4 = &pio4;
+ gpio5 = &pio5;
+ gpio6 = &pio6;
+ gpio7 = &pio7;
+ gpio8 = &pio8;
+ gpio9 = &pio9;
+ gpio10 = &pio10;
+ gpio11 = &pio11;
+ gpio12 = &pio12;
+ gpio13 = &pio13;
+ gpio14 = &pio14;
+ gpio15 = &pio15;
+ gpio16 = &pio16;
+ gpio17 = &pio17;
+ gpio18 = &pio18;
+ gpio19 = &pio100;
+ gpio20 = &pio101;
+ gpio21 = &pio102;
+ gpio22 = &pio103;
+ gpio23 = &pio104;
+ gpio24 = &pio105;
+ gpio25 = &pio106;
+ gpio26 = &pio107;
};
soc {
@@ -52,7 +52,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfe610000 0x5000>;
- PIO0: gpio at fe610000 {
+ pio0: gpio at fe610000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -60,7 +60,7 @@
reg = <0 0x100>;
st,bank-name = "PIO0";
};
- PIO1: gpio at fe611000 {
+ pio1: gpio at fe611000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -68,7 +68,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO1";
};
- PIO2: gpio at fe612000 {
+ pio2: gpio at fe612000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -76,7 +76,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO2";
};
- PIO3: gpio at fe613000 {
+ pio3: gpio at fe613000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -84,7 +84,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO3";
};
- PIO4: gpio at fe614000 {
+ pio4: gpio at fe614000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -96,8 +96,8 @@
sbc_serial1 {
pinctrl_sbc_serial1:sbc_serial1 {
st,pins {
- tx = <&PIO2 6 ALT3 OUT>;
- rx = <&PIO2 7 ALT3 IN>;
+ tx = <&pio2 6 ALT3 OUT>;
+ rx = <&pio2 7 ALT3 IN>;
};
};
};
@@ -105,15 +105,15 @@
keyscan {
pinctrl_keyscan: keyscan {
st,pins {
- keyin0 = <&PIO0 2 ALT2 IN>;
- keyin1 = <&PIO0 3 ALT2 IN>;
- keyin2 = <&PIO0 4 ALT2 IN>;
- keyin3 = <&PIO2 6 ALT2 IN>;
-
- keyout0 = <&PIO1 6 ALT2 OUT>;
- keyout1 = <&PIO1 7 ALT2 OUT>;
- keyout2 = <&PIO0 6 ALT2 OUT>;
- keyout3 = <&PIO2 7 ALT2 OUT>;
+ keyin0 = <&pio0 2 ALT2 IN>;
+ keyin1 = <&pio0 3 ALT2 IN>;
+ keyin2 = <&pio0 4 ALT2 IN>;
+ keyin3 = <&pio2 6 ALT2 IN>;
+
+ keyout0 = <&pio1 6 ALT2 OUT>;
+ keyout1 = <&pio1 7 ALT2 OUT>;
+ keyout2 = <&pio0 6 ALT2 OUT>;
+ keyout3 = <&pio2 7 ALT2 OUT>;
};
};
};
@@ -121,8 +121,8 @@
sbc_i2c0 {
pinctrl_sbc_i2c0_default: sbc_i2c0-default {
st,pins {
- sda = <&PIO4 6 ALT1 BIDIR>;
- scl = <&PIO4 5 ALT1 BIDIR>;
+ sda = <&pio4 6 ALT1 BIDIR>;
+ scl = <&pio4 5 ALT1 BIDIR>;
};
};
};
@@ -130,8 +130,8 @@
sbc_i2c1 {
pinctrl_sbc_i2c1_default: sbc_i2c1-default {
st,pins {
- sda = <&PIO3 2 ALT2 BIDIR>;
- scl = <&PIO3 1 ALT2 BIDIR>;
+ sda = <&pio3 2 ALT2 BIDIR>;
+ scl = <&pio3 1 ALT2 BIDIR>;
};
};
};
@@ -139,7 +139,7 @@
rc{
pinctrl_ir: ir0 {
st,pins {
- ir = <&PIO4 0 ALT2 IN>;
+ ir = <&pio4 0 ALT2 IN>;
};
};
};
@@ -147,49 +147,49 @@
gmac1 {
pinctrl_mii1: mii1 {
st,pins {
- txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
- col = <&PIO0 7 ALT1 IN BYPASS 1000>;
- mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
- mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
- crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
- mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
- rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
- phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
+ txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&pio0 7 ALT1 IN BYPASS 1000>;
+ mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&pio1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&pio1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&pio2 3 ALT1 IN NICLK 1000 CLK_A>;
};
};
pinctrl_rgmii1: rgmii1-0 {
st,pins {
- txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
- txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
- txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
- txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
- txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
- txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
- mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
- mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
- rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
- rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
- rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
- rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
-
- rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
- rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
- phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
-
- clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ txd0 = <&pio0 0 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd1 = <&pio0 1 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd2 = <&pio0 2 ALT1 OUT DE_IO 1000 CLK_A>;
+ txd3 = <&pio0 3 ALT1 OUT DE_IO 1000 CLK_A>;
+ txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
+ mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&pio1 4 ALT1 IN DE_IO 0 CLK_A>;
+ rxd1 = <&pio1 5 ALT1 IN DE_IO 0 CLK_A>;
+ rxd2 = <&pio1 6 ALT1 IN DE_IO 0 CLK_A>;
+ rxd3 = <&pio1 7 ALT1 IN DE_IO 0 CLK_A>;
+
+ rxdv = <&pio2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&pio2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
};
};
};
@@ -206,7 +206,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfee00000 0x8000>;
- PIO5: gpio at fee00000 {
+ pio5: gpio at fee00000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -214,7 +214,7 @@
reg = <0 0x100>;
st,bank-name = "PIO5";
};
- PIO6: gpio at fee01000 {
+ pio6: gpio at fee01000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -222,7 +222,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO6";
};
- PIO7: gpio at fee02000 {
+ pio7: gpio at fee02000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -230,7 +230,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO7";
};
- PIO8: gpio at fee03000 {
+ pio8: gpio at fee03000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -238,7 +238,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO8";
};
- PIO9: gpio at fee04000 {
+ pio9: gpio at fee04000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -246,7 +246,7 @@
reg = <0x4000 0x100>;
st,bank-name = "PIO9";
};
- PIO10: gpio at fee05000 {
+ pio10: gpio at fee05000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -254,7 +254,7 @@
reg = <0x5000 0x100>;
st,bank-name = "PIO10";
};
- PIO11: gpio at fee06000 {
+ pio11: gpio at fee06000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -262,7 +262,7 @@
reg = <0x6000 0x100>;
st,bank-name = "PIO11";
};
- PIO12: gpio at fee07000 {
+ pio12: gpio at fee07000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -274,8 +274,8 @@
i2c0 {
pinctrl_i2c0_default: i2c0-default {
st,pins {
- sda = <&PIO9 3 ALT1 BIDIR>;
- scl = <&PIO9 2 ALT1 BIDIR>;
+ sda = <&pio9 3 ALT1 BIDIR>;
+ scl = <&pio9 2 ALT1 BIDIR>;
};
};
};
@@ -283,8 +283,8 @@
i2c1 {
pinctrl_i2c1_default: i2c1-default {
st,pins {
- sda = <&PIO12 1 ALT1 BIDIR>;
- scl = <&PIO12 0 ALT1 BIDIR>;
+ sda = <&pio12 1 ALT1 BIDIR>;
+ scl = <&pio12 0 ALT1 BIDIR>;
};
};
};
@@ -301,7 +301,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfe820000 0x8000>;
- PIO13: gpio at fe820000 {
+ pio13: gpio at fe820000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -309,7 +309,7 @@
reg = <0 0x100>;
st,bank-name = "PIO13";
};
- PIO14: gpio at fe821000 {
+ pio14: gpio at fe821000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -317,7 +317,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO14";
};
- PIO15: gpio at fe822000 {
+ pio15: gpio at fe822000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -325,7 +325,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO15";
};
- PIO16: gpio at fe823000 {
+ pio16: gpio at fe823000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -333,7 +333,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO16";
};
- PIO17: gpio at fe824000 {
+ pio17: gpio at fe824000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -341,7 +341,7 @@
reg = <0x4000 0x100>;
st,bank-name = "PIO17";
};
- PIO18: gpio at fe825000 {
+ pio18: gpio at fe825000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -353,8 +353,8 @@
serial2 {
pinctrl_serial2: serial2-0 {
st,pins {
- tx = <&PIO17 4 ALT2 OUT>;
- rx = <&PIO17 5 ALT2 IN>;
+ tx = <&pio17 4 ALT2 OUT>;
+ rx = <&pio17 5 ALT2 IN>;
};
};
};
@@ -362,68 +362,68 @@
gmac0{
pinctrl_mii0: mii0 {
st,pins {
- mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
- txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
-
- txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
- txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
-
- txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
- txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
- col = <&PIO15 3 ALT2 IN BYPASS 1000>;
- mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
- mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
-
- rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
- phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
+ mdint = <&pio13 6 ALT2 IN BYPASS 0>;
+ txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+
+ txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&pio15 2 ALT2 IN BYPASS 1000>;
+ col = <&pio15 3 ALT2 IN BYPASS 1000>;
+ mdio = <&pio15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&pio13 5 ALT2 OUT NICLK 1000 CLK_A>;
};
};
pinctrl_gmii0: gmii0 {
st,pins {
- mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
- mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
- mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
- txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
-
- txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
- txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
- txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
- txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
- txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
- txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
- txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
- txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
-
- txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
- txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
- crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
- col = <&PIO15 3 ALT2 IN BYPASS 1000>;
- rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
-
- rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
- rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
-
- rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
- clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
- phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
+ mdint = <&pio13 6 ALT2 IN BYPASS 0>;
+ mdio = <&pio15 4 ALT2 OUT BYPASS 3000>;
+ mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
+ txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+
+ txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd4 = <&pio14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd5 = <&pio14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd6 = <&pio14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+ txd7 = <&pio14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
+
+ txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
+ crs = <&pio15 2 ALT2 IN BYPASS 1000>;
+ col = <&pio15 3 ALT2 IN BYPASS 1000>;
+ rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd4 = <&pio16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd5 = <&pio16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd6 = <&pio16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+ rxd7 = <&pio16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
+
+ rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
+ clk125 = <&pio17 6 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&pio13 5 ALT4 OUT NICLK 0 CLK_B>;
};
@@ -442,7 +442,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfd6b0000 0x3000>;
- PIO100: gpio at fd6b0000 {
+ pio100: gpio at fd6b0000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -450,7 +450,7 @@
reg = <0 0x100>;
st,bank-name = "PIO100";
};
- PIO101: gpio at fd6b1000 {
+ pio101: gpio at fd6b1000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -458,7 +458,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO101";
};
- PIO102: gpio at fd6b2000 {
+ pio102: gpio at fd6b2000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -479,7 +479,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfd330000 0x5000>;
- PIO103: gpio at fd330000 {
+ pio103: gpio at fd330000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -487,7 +487,7 @@
reg = <0 0x100>;
st,bank-name = "PIO103";
};
- PIO104: gpio at fd331000 {
+ pio104: gpio at fd331000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -495,7 +495,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO104";
};
- PIO105: gpio at fd332000 {
+ pio105: gpio at fd332000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -503,7 +503,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO105";
};
- PIO106: gpio at fd333000 {
+ pio106: gpio at fd333000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -511,7 +511,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO106";
};
- PIO107: gpio at fd334000 {
+ pio107: gpio at fd334000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
diff --git a/arch/arm/boot/dts/stih416-b2020-revE.dts b/arch/arm/boot/dts/stih416-b2020-revE.dts
index ba0fa2c..d72e5c7 100644
--- a/arch/arm/boot/dts/stih416-b2020-revE.dts
+++ b/arch/arm/boot/dts/stih416-b2020-revE.dts
@@ -19,17 +19,17 @@
red {
#gpio-cells = <1>;
label = "Front Panel LED";
- gpios = <&PIO4 1>;
+ gpios = <&pio4 1>;
linux,default-trigger = "heartbeat";
};
green {
- gpios = <&PIO1 3>;
+ gpios = <&pio1 3>;
default-state = "off";
};
};
ethernet1: dwmac at fef08000 {
- snps,reset-gpio = <&PIO0 7>;
+ snps,reset-gpio = <&pio0 7>;
};
};
};
diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
index 6252188..3e06d7f 100644
--- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
@@ -12,36 +12,36 @@
/ {
aliases {
- gpio0 = &PIO0;
- gpio1 = &PIO1;
- gpio2 = &PIO2;
- gpio3 = &PIO3;
- gpio4 = &PIO4;
- gpio5 = &PIO40;
- gpio6 = &PIO5;
- gpio7 = &PIO6;
- gpio8 = &PIO7;
- gpio9 = &PIO8;
- gpio10 = &PIO9;
- gpio11 = &PIO10;
- gpio12 = &PIO11;
- gpio13 = &PIO12;
- gpio14 = &PIO30;
- gpio15 = &PIO31;
- gpio16 = &PIO13;
- gpio17 = &PIO14;
- gpio18 = &PIO15;
- gpio19 = &PIO16;
- gpio20 = &PIO17;
- gpio21 = &PIO18;
- gpio22 = &PIO100;
- gpio23 = &PIO101;
- gpio24 = &PIO102;
- gpio25 = &PIO103;
- gpio26 = &PIO104;
- gpio27 = &PIO105;
- gpio28 = &PIO106;
- gpio29 = &PIO107;
+ gpio0 = &pio0;
+ gpio1 = &pio1;
+ gpio2 = &pio2;
+ gpio3 = &pio3;
+ gpio4 = &pio4;
+ gpio5 = &pio40;
+ gpio6 = &pio5;
+ gpio7 = &pio6;
+ gpio8 = &pio7;
+ gpio9 = &pio8;
+ gpio10 = &pio9;
+ gpio11 = &pio10;
+ gpio12 = &pio11;
+ gpio13 = &pio12;
+ gpio14 = &pio30;
+ gpio15 = &pio31;
+ gpio16 = &pio13;
+ gpio17 = &pio14;
+ gpio18 = &pio15;
+ gpio19 = &pio16;
+ gpio20 = &pio17;
+ gpio21 = &pio18;
+ gpio22 = &pio100;
+ gpio23 = &pio101;
+ gpio24 = &pio102;
+ gpio25 = &pio103;
+ gpio26 = &pio104;
+ gpio27 = &pio105;
+ gpio28 = &pio106;
+ gpio29 = &pio107;
};
soc {
@@ -56,7 +56,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfe610000 0x6000>;
- PIO0: gpio at fe610000 {
+ pio0: gpio at fe610000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -64,7 +64,7 @@
reg = <0 0x100>;
st,bank-name = "PIO0";
};
- PIO1: gpio at fe611000 {
+ pio1: gpio at fe611000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -72,7 +72,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO1";
};
- PIO2: gpio at fe612000 {
+ pio2: gpio at fe612000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -80,7 +80,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO2";
};
- PIO3: gpio at fe613000 {
+ pio3: gpio at fe613000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -88,7 +88,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO3";
};
- PIO4: gpio at fe614000 {
+ pio4: gpio at fe614000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -96,7 +96,7 @@
reg = <0x4000 0x100>;
st,bank-name = "PIO4";
};
- PIO40: gpio at fe615000 {
+ pio40: gpio at fe615000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -109,15 +109,15 @@
rc{
pinctrl_ir: ir0 {
st,pins {
- ir = <&PIO4 0 ALT2 IN>;
+ ir = <&pio4 0 ALT2 IN>;
};
};
};
sbc_serial1 {
pinctrl_sbc_serial1: sbc_serial1 {
st,pins {
- tx = <&PIO2 6 ALT3 OUT>;
- rx = <&PIO2 7 ALT3 IN>;
+ tx = <&pio2 6 ALT3 OUT>;
+ rx = <&pio2 7 ALT3 IN>;
};
};
};
@@ -125,15 +125,15 @@
keyscan {
pinctrl_keyscan: keyscan {
st,pins {
- keyin0 = <&PIO0 2 ALT2 IN>;
- keyin1 = <&PIO0 3 ALT2 IN>;
- keyin2 = <&PIO0 4 ALT2 IN>;
- keyin3 = <&PIO2 6 ALT2 IN>;
-
- keyout0 = <&PIO1 6 ALT2 OUT>;
- keyout1 = <&PIO1 7 ALT2 OUT>;
- keyout2 = <&PIO0 6 ALT2 OUT>;
- keyout3 = <&PIO2 7 ALT2 OUT>;
+ keyin0 = <&pio0 2 ALT2 IN>;
+ keyin1 = <&pio0 3 ALT2 IN>;
+ keyin2 = <&pio0 4 ALT2 IN>;
+ keyin3 = <&pio2 6 ALT2 IN>;
+
+ keyout0 = <&pio1 6 ALT2 OUT>;
+ keyout1 = <&pio1 7 ALT2 OUT>;
+ keyout2 = <&pio0 6 ALT2 OUT>;
+ keyout3 = <&pio2 7 ALT2 OUT>;
};
};
};
@@ -141,8 +141,8 @@
sbc_i2c0 {
pinctrl_sbc_i2c0_default: sbc_i2c0-default {
st,pins {
- sda = <&PIO4 6 ALT1 BIDIR>;
- scl = <&PIO4 5 ALT1 BIDIR>;
+ sda = <&pio4 6 ALT1 BIDIR>;
+ scl = <&pio4 5 ALT1 BIDIR>;
};
};
};
@@ -150,8 +150,8 @@
sbc_i2c1 {
pinctrl_sbc_i2c1_default: sbc_i2c1-default {
st,pins {
- sda = <&PIO3 2 ALT2 BIDIR>;
- scl = <&PIO3 1 ALT2 BIDIR>;
+ sda = <&pio3 2 ALT2 BIDIR>;
+ scl = <&pio3 1 ALT2 BIDIR>;
};
};
};
@@ -159,51 +159,51 @@
gmac1 {
pinctrl_mii1: mii1 {
st,pins {
- txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
- txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
- col = <&PIO0 7 ALT1 IN BYPASS 1000>;
-
- mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
- mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
- crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
- mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
- rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
-
- rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
- rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
- phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
+ txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+ txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
+ col = <&pio0 7 ALT1 IN BYPASS 1000>;
+
+ mdio = <&pio1 0 ALT1 OUT BYPASS 1500>;
+ mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+ crs = <&pio1 2 ALT1 IN BYPASS 1000>;
+ mdint = <&pio1 3 ALT1 IN BYPASS 0>;
+ rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+ rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>;
};
};
pinctrl_rgmii1: rgmii1-0 {
st,pins {
- txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
- txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
- txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
- txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
- txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
- txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
-
- mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
- mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
- rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
- rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
- rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
- rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
-
- rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
- rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
- phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
-
- clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+ txd0 = <&pio0 0 ALT1 OUT DE_IO 500 CLK_A>;
+ txd1 = <&pio0 1 ALT1 OUT DE_IO 500 CLK_A>;
+ txd2 = <&pio0 2 ALT1 OUT DE_IO 500 CLK_A>;
+ txd3 = <&pio0 3 ALT1 OUT DE_IO 500 CLK_A>;
+ txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
+ txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
+
+ mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
+ mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+ rxd0 = <&pio1 4 ALT1 IN DE_IO 500 CLK_A>;
+ rxd1 = <&pio1 5 ALT1 IN DE_IO 500 CLK_A>;
+ rxd2 = <&pio1 6 ALT1 IN DE_IO 500 CLK_A>;
+ rxd3 = <&pio1 7 ALT1 IN DE_IO 500 CLK_A>;
+
+ rxdv = <&pio2 0 ALT1 IN DE_IO 500 CLK_A>;
+ rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&pio2 3 ALT4 OUT NICLK 0 CLK_B>;
+
+ clk125= <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
};
};
};
@@ -220,7 +220,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfee00000 0x10000>;
- PIO5: gpio at fee00000 {
+ pio5: gpio at fee00000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -228,7 +228,7 @@
reg = <0 0x100>;
st,bank-name = "PIO5";
};
- PIO6: gpio at fee01000 {
+ pio6: gpio at fee01000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -236,7 +236,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO6";
};
- PIO7: gpio at fee02000 {
+ pio7: gpio at fee02000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -244,7 +244,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO7";
};
- PIO8: gpio at fee03000 {
+ pio8: gpio at fee03000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -252,7 +252,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO8";
};
- PIO9: gpio at fee04000 {
+ pio9: gpio at fee04000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -260,7 +260,7 @@
reg = <0x4000 0x100>;
st,bank-name = "PIO9";
};
- PIO10: gpio at fee05000 {
+ pio10: gpio at fee05000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -268,7 +268,7 @@
reg = <0x5000 0x100>;
st,bank-name = "PIO10";
};
- PIO11: gpio at fee06000 {
+ pio11: gpio at fee06000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -276,7 +276,7 @@
reg = <0x6000 0x100>;
st,bank-name = "PIO11";
};
- PIO12: gpio at fee07000 {
+ pio12: gpio at fee07000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -284,7 +284,7 @@
reg = <0x7000 0x100>;
st,bank-name = "PIO12";
};
- PIO30: gpio at fee08000 {
+ pio30: gpio at fee08000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -292,7 +292,7 @@
reg = <0x8000 0x100>;
st,bank-name = "PIO30";
};
- PIO31: gpio at fee09000 {
+ pio31: gpio at fee09000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -304,7 +304,7 @@
serial2-oe {
pinctrl_serial2_oe: serial2-1 {
st,pins {
- output-enable = <&PIO11 3 ALT2 OUT>;
+ output-enable = <&pio11 3 ALT2 OUT>;
};
};
};
@@ -312,8 +312,8 @@
i2c0 {
pinctrl_i2c0_default: i2c0-default {
st,pins {
- sda = <&PIO9 3 ALT1 BIDIR>;
- scl = <&PIO9 2 ALT1 BIDIR>;
+ sda = <&pio9 3 ALT1 BIDIR>;
+ scl = <&pio9 2 ALT1 BIDIR>;
};
};
};
@@ -321,8 +321,8 @@
i2c1 {
pinctrl_i2c1_default: i2c1-default {
st,pins {
- sda = <&PIO12 1 ALT1 BIDIR>;
- scl = <&PIO12 0 ALT1 BIDIR>;
+ sda = <&pio12 1 ALT1 BIDIR>;
+ scl = <&pio12 0 ALT1 BIDIR>;
};
};
};
@@ -330,12 +330,12 @@
fsm {
pinctrl_fsm: fsm {
st,pins {
- spi-fsm-clk = <&PIO12 2 ALT1 OUT>;
- spi-fsm-cs = <&PIO12 3 ALT1 OUT>;
- spi-fsm-mosi = <&PIO12 4 ALT1 OUT>;
- spi-fsm-miso = <&PIO12 5 ALT1 IN>;
- spi-fsm-hol = <&PIO12 6 ALT1 OUT>;
- spi-fsm-wp = <&PIO12 7 ALT1 OUT>;
+ spi-fsm-clk = <&pio12 2 ALT1 OUT>;
+ spi-fsm-cs = <&pio12 3 ALT1 OUT>;
+ spi-fsm-mosi = <&pio12 4 ALT1 OUT>;
+ spi-fsm-miso = <&pio12 5 ALT1 IN>;
+ spi-fsm-hol = <&pio12 6 ALT1 OUT>;
+ spi-fsm-wp = <&pio12 7 ALT1 OUT>;
};
};
};
@@ -352,7 +352,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfe820000 0x6000>;
- PIO13: gpio at fe820000 {
+ pio13: gpio at fe820000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -360,7 +360,7 @@
reg = <0 0x100>;
st,bank-name = "PIO13";
};
- PIO14: gpio at fe821000 {
+ pio14: gpio at fe821000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -368,7 +368,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO14";
};
- PIO15: gpio at fe822000 {
+ pio15: gpio at fe822000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -376,7 +376,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO15";
};
- PIO16: gpio at fe823000 {
+ pio16: gpio at fe823000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -384,7 +384,7 @@
reg = <0x3000 0x100>;
st,bank-name = "PIO16";
};
- PIO17: gpio at fe824000 {
+ pio17: gpio at fe824000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -392,7 +392,7 @@
reg = <0x4000 0x100>;
st,bank-name = "PIO17";
};
- PIO18: gpio at fe825000 {
+ pio18: gpio at fe825000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -405,8 +405,8 @@
serial2 {
pinctrl_serial2: serial2-0 {
st,pins {
- tx = <&PIO17 4 ALT2 OUT>;
- rx = <&PIO17 5 ALT2 IN>;
+ tx = <&pio17 4 ALT2 OUT>;
+ rx = <&pio17 5 ALT2 IN>;
};
};
};
@@ -414,28 +414,28 @@
gmac0 {
pinctrl_mii0: mii0 {
st,pins {
- mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
- txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
- txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
-
- txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
- txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
- crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
- col = <&PIO15 3 ALT2 IN BYPASS 1000>;
- mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
- mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
-
- rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
- rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
- phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
+ mdint = <&pio13 6 ALT2 IN BYPASS 0>;
+ txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+ txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+ txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
+ txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+ crs = <&pio15 2 ALT2 IN BYPASS 1000>;
+ col = <&pio15 3 ALT2 IN BYPASS 1000>;
+ mdio= <&pio15 4 ALT2 OUT BYPASS 1500>;
+ mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+ rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
+ phyclk = <&pio13 5 ALT2 OUT NICLK 0 CLK_B>;
};
};
@@ -445,25 +445,25 @@
};
pinctrl_rgmii0: rgmii0 {
st,pins {
- phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
- txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
- txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
- txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
- txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
- txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
- txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
-
- mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
- mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
-
- rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
- rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
- rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
- rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
- rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
- rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
-
- clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+ phyclk = <&pio13 5 ALT4 OUT NICLK 0 CLK_B>;
+ txen = <&pio13 7 ALT2 OUT DE_IO 0 CLK_A>;
+ txd0 = <&pio14 0 ALT2 OUT DE_IO 500 CLK_A>;
+ txd1 = <&pio14 1 ALT2 OUT DE_IO 500 CLK_A>;
+ txd2 = <&pio14 2 ALT2 OUT DE_IO 500 CLK_B>;
+ txd3 = <&pio14 3 ALT2 OUT DE_IO 500 CLK_B>;
+ txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
+
+ mdio = <&pio15 4 ALT2 OUT BYPASS 0>;
+ mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+ rxdv = <&pio15 6 ALT2 IN DE_IO 500 CLK_A>;
+ rxd0 =<&pio16 0 ALT2 IN DE_IO 500 CLK_A>;
+ rxd1 =<&pio16 1 ALT2 IN DE_IO 500 CLK_A>;
+ rxd2 =<&pio16 2 ALT2 IN DE_IO 500 CLK_A>;
+ rxd3 =<&pio16 3 ALT2 IN DE_IO 500 CLK_A>;
+ rxclk =<&pio17 0 ALT2 IN NICLK 0 CLK_A>;
+
+ clk125=<&pio17 6 ALT1 IN NICLK 0 CLK_A>;
};
};
};
@@ -480,7 +480,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfd6b0000 0x3000>;
- PIO100: gpio at fd6b0000 {
+ pio100: gpio at fd6b0000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -488,7 +488,7 @@
reg = <0 0x100>;
st,bank-name = "PIO100";
};
- PIO101: gpio at fd6b1000 {
+ pio101: gpio at fd6b1000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -496,7 +496,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO101";
};
- PIO102: gpio at fd6b2000 {
+ pio102: gpio at fd6b2000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -517,7 +517,7 @@
interrupts-names = "irqmux";
ranges = <0 0xfd330000 0x5000>;
- PIO103: gpio at fd330000 {
+ pio103: gpio at fd330000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -525,7 +525,7 @@
reg = <0 0x100>;
st,bank-name = "PIO103";
};
- PIO104: gpio at fd331000 {
+ pio104: gpio at fd331000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -533,7 +533,7 @@
reg = <0x1000 0x100>;
st,bank-name = "PIO104";
};
- PIO105: gpio at fd332000 {
+ pio105: gpio at fd332000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -541,7 +541,7 @@
reg = <0x2000 0x100>;
st,bank-name = "PIO105";
};
- PIO106: gpio at fd333000 {
+ pio106: gpio at fd333000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
@@ -550,7 +550,7 @@
st,bank-name = "PIO106";
};
- PIO107: gpio at fd334000 {
+ pio107: gpio at fd334000 {
gpio-controller;
#gpio-cells = <1>;
interrupt-controller;
diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
index b3dd6ca..5f91f45 100644
--- a/arch/arm/boot/dts/stih41x-b2000.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
@@ -35,7 +35,7 @@
fp_led {
#gpio-cells = <1>;
label = "Front Panel LED";
- gpios = <&PIO105 7>;
+ gpios = <&pio105 7>;
linux,default-trigger = "heartbeat";
};
};
@@ -55,7 +55,7 @@
phy-mode = "mii";
pinctrl-0 = <&pinctrl_mii0>;
- snps,reset-gpio = <&PIO106 2>;
+ snps,reset-gpio = <&pio106 2>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 10000>;
};
@@ -65,7 +65,7 @@
phy-mode = "mii";
st,tx-retime-src = "txclk";
- snps,reset-gpio = <&PIO4 7>;
+ snps,reset-gpio = <&pio4 7>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 10000>;
};
diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
index d8a8429..c0f50e9 100644
--- a/arch/arm/boot/dts/stih41x-b2020.dtsi
+++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
@@ -32,11 +32,11 @@
red {
#gpio-cells = <1>;
label = "Front Panel LED";
- gpios = <&PIO4 1>;
+ gpios = <&pio4 1>;
linux,default-trigger = "heartbeat";
};
green {
- gpios = <&PIO4 7>;
+ gpios = <&pio4 7>;
default-state = "off";
};
};
@@ -68,7 +68,7 @@
phy-mode = "rgmii-id";
max-speed = <1000>;
st,tx-retime-src = "clk_125";
- snps,reset-gpio = <&PIO3 0>;
+ snps,reset-gpio = <&pio3 0>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 10000>;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
2014-05-27 12:53 [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase Lee Jones
@ 2014-05-27 18:01 ` Olof Johansson
2014-06-25 14:53 ` Lee Jones
1 sibling, 0 replies; 6+ messages in thread
From: Olof Johansson @ 2014-05-27 18:01 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, May 27, 2014 at 01:53:08PM +0100, Lee Jones wrote:
> Suggested-by: Olof Johansson <olof@lixom.net>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
> arch/arm/boot/dts/stih415-pinctrl.dtsi | 340 +++++++++++++++---------------
> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
> arch/arm/boot/dts/stih416-pinctrl.dtsi | 342 +++++++++++++++----------------
> arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
> arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +-
> 5 files changed, 350 insertions(+), 350 deletions(-)
Acked-by: Olof Johansson <olof@lixom.net>
-Olof
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
2014-05-27 12:53 [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase Lee Jones
2014-05-27 18:01 ` Olof Johansson
@ 2014-06-25 14:53 ` Lee Jones
2014-06-25 15:08 ` Maxime Coquelin
1 sibling, 1 reply; 6+ messages in thread
From: Lee Jones @ 2014-06-25 14:53 UTC (permalink / raw)
To: linux-arm-kernel
> Suggested-by: Olof Johansson <olof@lixom.net>
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
> arch/arm/boot/dts/stih415-pinctrl.dtsi | 340 +++++++++++++++---------------
> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
> arch/arm/boot/dts/stih416-pinctrl.dtsi | 342 +++++++++++++++----------------
> arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
> arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +-
> 5 files changed, 350 insertions(+), 350 deletions(-)
What happened to this Maxime?
It was Acked by Olof, then died. Did it slip through the net?
> diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi
> index caeac7e..1e0255d 100644
> --- a/arch/arm/boot/dts/stih415-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi
> @@ -11,33 +11,33 @@
> / {
>
> aliases {
> - gpio0 = &PIO0;
> - gpio1 = &PIO1;
> - gpio2 = &PIO2;
> - gpio3 = &PIO3;
> - gpio4 = &PIO4;
> - gpio5 = &PIO5;
> - gpio6 = &PIO6;
> - gpio7 = &PIO7;
> - gpio8 = &PIO8;
> - gpio9 = &PIO9;
> - gpio10 = &PIO10;
> - gpio11 = &PIO11;
> - gpio12 = &PIO12;
> - gpio13 = &PIO13;
> - gpio14 = &PIO14;
> - gpio15 = &PIO15;
> - gpio16 = &PIO16;
> - gpio17 = &PIO17;
> - gpio18 = &PIO18;
> - gpio19 = &PIO100;
> - gpio20 = &PIO101;
> - gpio21 = &PIO102;
> - gpio22 = &PIO103;
> - gpio23 = &PIO104;
> - gpio24 = &PIO105;
> - gpio25 = &PIO106;
> - gpio26 = &PIO107;
> + gpio0 = &pio0;
> + gpio1 = &pio1;
> + gpio2 = &pio2;
> + gpio3 = &pio3;
> + gpio4 = &pio4;
> + gpio5 = &pio5;
> + gpio6 = &pio6;
> + gpio7 = &pio7;
> + gpio8 = &pio8;
> + gpio9 = &pio9;
> + gpio10 = &pio10;
> + gpio11 = &pio11;
> + gpio12 = &pio12;
> + gpio13 = &pio13;
> + gpio14 = &pio14;
> + gpio15 = &pio15;
> + gpio16 = &pio16;
> + gpio17 = &pio17;
> + gpio18 = &pio18;
> + gpio19 = &pio100;
> + gpio20 = &pio101;
> + gpio21 = &pio102;
> + gpio22 = &pio103;
> + gpio23 = &pio104;
> + gpio24 = &pio105;
> + gpio25 = &pio106;
> + gpio26 = &pio107;
> };
>
> soc {
> @@ -52,7 +52,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe610000 0x5000>;
>
> - PIO0: gpio at fe610000 {
> + pio0: gpio at fe610000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -60,7 +60,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO0";
> };
> - PIO1: gpio at fe611000 {
> + pio1: gpio at fe611000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -68,7 +68,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO1";
> };
> - PIO2: gpio at fe612000 {
> + pio2: gpio at fe612000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -76,7 +76,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO2";
> };
> - PIO3: gpio at fe613000 {
> + pio3: gpio at fe613000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -84,7 +84,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO3";
> };
> - PIO4: gpio at fe614000 {
> + pio4: gpio at fe614000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -96,8 +96,8 @@
> sbc_serial1 {
> pinctrl_sbc_serial1:sbc_serial1 {
> st,pins {
> - tx = <&PIO2 6 ALT3 OUT>;
> - rx = <&PIO2 7 ALT3 IN>;
> + tx = <&pio2 6 ALT3 OUT>;
> + rx = <&pio2 7 ALT3 IN>;
> };
> };
> };
> @@ -105,15 +105,15 @@
> keyscan {
> pinctrl_keyscan: keyscan {
> st,pins {
> - keyin0 = <&PIO0 2 ALT2 IN>;
> - keyin1 = <&PIO0 3 ALT2 IN>;
> - keyin2 = <&PIO0 4 ALT2 IN>;
> - keyin3 = <&PIO2 6 ALT2 IN>;
> -
> - keyout0 = <&PIO1 6 ALT2 OUT>;
> - keyout1 = <&PIO1 7 ALT2 OUT>;
> - keyout2 = <&PIO0 6 ALT2 OUT>;
> - keyout3 = <&PIO2 7 ALT2 OUT>;
> + keyin0 = <&pio0 2 ALT2 IN>;
> + keyin1 = <&pio0 3 ALT2 IN>;
> + keyin2 = <&pio0 4 ALT2 IN>;
> + keyin3 = <&pio2 6 ALT2 IN>;
> +
> + keyout0 = <&pio1 6 ALT2 OUT>;
> + keyout1 = <&pio1 7 ALT2 OUT>;
> + keyout2 = <&pio0 6 ALT2 OUT>;
> + keyout3 = <&pio2 7 ALT2 OUT>;
> };
> };
> };
> @@ -121,8 +121,8 @@
> sbc_i2c0 {
> pinctrl_sbc_i2c0_default: sbc_i2c0-default {
> st,pins {
> - sda = <&PIO4 6 ALT1 BIDIR>;
> - scl = <&PIO4 5 ALT1 BIDIR>;
> + sda = <&pio4 6 ALT1 BIDIR>;
> + scl = <&pio4 5 ALT1 BIDIR>;
> };
> };
> };
> @@ -130,8 +130,8 @@
> sbc_i2c1 {
> pinctrl_sbc_i2c1_default: sbc_i2c1-default {
> st,pins {
> - sda = <&PIO3 2 ALT2 BIDIR>;
> - scl = <&PIO3 1 ALT2 BIDIR>;
> + sda = <&pio3 2 ALT2 BIDIR>;
> + scl = <&pio3 1 ALT2 BIDIR>;
> };
> };
> };
> @@ -139,7 +139,7 @@
> rc{
> pinctrl_ir: ir0 {
> st,pins {
> - ir = <&PIO4 0 ALT2 IN>;
> + ir = <&pio4 0 ALT2 IN>;
> };
> };
> };
> @@ -147,49 +147,49 @@
> gmac1 {
> pinctrl_mii1: mii1 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> - col = <&PIO0 7 ALT1 IN BYPASS 1000>;
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
> - mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
> - rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> + col = <&pio0 7 ALT1 IN BYPASS 1000>;
> + mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + crs = <&pio1 2 ALT1 IN BYPASS 1000>;
> + mdint = <&pio1 3 ALT1 IN BYPASS 0>;
> + rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT1 IN NICLK 1000 CLK_A>;
> };
> };
>
> pinctrl_rgmii1: rgmii1-0 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>;
> -
> - rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
> -
> - clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT DE_IO 1000 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT DE_IO 1000 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT DE_IO 1000 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT DE_IO 1000 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> + mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + rxd0 = <&pio1 4 ALT1 IN DE_IO 0 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN DE_IO 0 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN DE_IO 0 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN DE_IO 0 CLK_A>;
> +
> + rxdv = <&pio2 0 ALT1 IN DE_IO 500 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT4 OUT NICLK 0 CLK_B>;
> +
> + clk125= <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
> };
> };
> };
> @@ -206,7 +206,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfee00000 0x8000>;
>
> - PIO5: gpio at fee00000 {
> + pio5: gpio at fee00000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -214,7 +214,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO5";
> };
> - PIO6: gpio at fee01000 {
> + pio6: gpio at fee01000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -222,7 +222,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO6";
> };
> - PIO7: gpio at fee02000 {
> + pio7: gpio at fee02000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -230,7 +230,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO7";
> };
> - PIO8: gpio at fee03000 {
> + pio8: gpio at fee03000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -238,7 +238,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO8";
> };
> - PIO9: gpio at fee04000 {
> + pio9: gpio at fee04000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -246,7 +246,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO9";
> };
> - PIO10: gpio at fee05000 {
> + pio10: gpio at fee05000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -254,7 +254,7 @@
> reg = <0x5000 0x100>;
> st,bank-name = "PIO10";
> };
> - PIO11: gpio at fee06000 {
> + pio11: gpio at fee06000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -262,7 +262,7 @@
> reg = <0x6000 0x100>;
> st,bank-name = "PIO11";
> };
> - PIO12: gpio at fee07000 {
> + pio12: gpio at fee07000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -274,8 +274,8 @@
> i2c0 {
> pinctrl_i2c0_default: i2c0-default {
> st,pins {
> - sda = <&PIO9 3 ALT1 BIDIR>;
> - scl = <&PIO9 2 ALT1 BIDIR>;
> + sda = <&pio9 3 ALT1 BIDIR>;
> + scl = <&pio9 2 ALT1 BIDIR>;
> };
> };
> };
> @@ -283,8 +283,8 @@
> i2c1 {
> pinctrl_i2c1_default: i2c1-default {
> st,pins {
> - sda = <&PIO12 1 ALT1 BIDIR>;
> - scl = <&PIO12 0 ALT1 BIDIR>;
> + sda = <&pio12 1 ALT1 BIDIR>;
> + scl = <&pio12 0 ALT1 BIDIR>;
> };
> };
> };
> @@ -301,7 +301,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe820000 0x8000>;
>
> - PIO13: gpio at fe820000 {
> + pio13: gpio at fe820000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -309,7 +309,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO13";
> };
> - PIO14: gpio at fe821000 {
> + pio14: gpio at fe821000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -317,7 +317,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO14";
> };
> - PIO15: gpio at fe822000 {
> + pio15: gpio at fe822000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -325,7 +325,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO15";
> };
> - PIO16: gpio at fe823000 {
> + pio16: gpio at fe823000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -333,7 +333,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO16";
> };
> - PIO17: gpio at fe824000 {
> + pio17: gpio at fe824000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -341,7 +341,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO17";
> };
> - PIO18: gpio at fe825000 {
> + pio18: gpio at fe825000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -353,8 +353,8 @@
> serial2 {
> pinctrl_serial2: serial2-0 {
> st,pins {
> - tx = <&PIO17 4 ALT2 OUT>;
> - rx = <&PIO17 5 ALT2 IN>;
> + tx = <&pio17 4 ALT2 OUT>;
> + rx = <&pio17 5 ALT2 IN>;
> };
> };
> };
> @@ -362,68 +362,68 @@
> gmac0{
> pinctrl_mii0: mii0 {
> st,pins {
> - mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
> - txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> -
> - txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> -
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> - txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
> - col = <&PIO15 3 ALT2 IN BYPASS 1000>;
> - mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> -
> - rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>;
> + mdint = <&pio13 6 ALT2 IN BYPASS 0>;
> + txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> +
> + txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> +
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> + txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + crs = <&pio15 2 ALT2 IN BYPASS 1000>;
> + col = <&pio15 3 ALT2 IN BYPASS 1000>;
> + mdio = <&pio15 4 ALT2 OUT BYPASS 3000>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> +
> + rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT2 OUT NICLK 1000 CLK_A>;
>
> };
> };
>
> pinctrl_gmii0: gmii0 {
> st,pins {
> - mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
> - mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> - txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> -
> - txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> - txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> -
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> - txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> - crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
> - col = <&PIO15 3 ALT2 IN BYPASS 1000>;
> - rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> -
> - rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> - rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> -
> - rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> - clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
> + mdint = <&pio13 6 ALT2 IN BYPASS 0>;
> + mdio = <&pio15 4 ALT2 OUT BYPASS 3000>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> + txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> +
> + txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd4 = <&pio14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd5 = <&pio14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd6 = <&pio14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> + txd7 = <&pio14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>;
> +
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> + txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>;
> + crs = <&pio15 2 ALT2 IN BYPASS 1000>;
> + col = <&pio15 3 ALT2 IN BYPASS 1000>;
> + rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> +
> + rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd4 = <&pio16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd5 = <&pio16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd6 = <&pio16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> + rxd7 = <&pio16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>;
> +
> + rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> + clk125 = <&pio17 6 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT4 OUT NICLK 0 CLK_B>;
>
>
> };
> @@ -442,7 +442,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd6b0000 0x3000>;
>
> - PIO100: gpio at fd6b0000 {
> + pio100: gpio at fd6b0000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -450,7 +450,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO100";
> };
> - PIO101: gpio at fd6b1000 {
> + pio101: gpio at fd6b1000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -458,7 +458,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO101";
> };
> - PIO102: gpio at fd6b2000 {
> + pio102: gpio at fd6b2000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -479,7 +479,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd330000 0x5000>;
>
> - PIO103: gpio at fd330000 {
> + pio103: gpio at fd330000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -487,7 +487,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO103";
> };
> - PIO104: gpio at fd331000 {
> + pio104: gpio at fd331000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -495,7 +495,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO104";
> };
> - PIO105: gpio at fd332000 {
> + pio105: gpio at fd332000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -503,7 +503,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO105";
> };
> - PIO106: gpio at fd333000 {
> + pio106: gpio at fd333000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -511,7 +511,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO106";
> };
> - PIO107: gpio at fd334000 {
> + pio107: gpio at fd334000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> diff --git a/arch/arm/boot/dts/stih416-b2020-revE.dts b/arch/arm/boot/dts/stih416-b2020-revE.dts
> index ba0fa2c..d72e5c7 100644
> --- a/arch/arm/boot/dts/stih416-b2020-revE.dts
> +++ b/arch/arm/boot/dts/stih416-b2020-revE.dts
> @@ -19,17 +19,17 @@
> red {
> #gpio-cells = <1>;
> label = "Front Panel LED";
> - gpios = <&PIO4 1>;
> + gpios = <&pio4 1>;
> linux,default-trigger = "heartbeat";
> };
> green {
> - gpios = <&PIO1 3>;
> + gpios = <&pio1 3>;
> default-state = "off";
> };
> };
>
> ethernet1: dwmac at fef08000 {
> - snps,reset-gpio = <&PIO0 7>;
> + snps,reset-gpio = <&pio0 7>;
> };
> };
> };
> diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi
> index 6252188..3e06d7f 100644
> --- a/arch/arm/boot/dts/stih416-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi
> @@ -12,36 +12,36 @@
> / {
>
> aliases {
> - gpio0 = &PIO0;
> - gpio1 = &PIO1;
> - gpio2 = &PIO2;
> - gpio3 = &PIO3;
> - gpio4 = &PIO4;
> - gpio5 = &PIO40;
> - gpio6 = &PIO5;
> - gpio7 = &PIO6;
> - gpio8 = &PIO7;
> - gpio9 = &PIO8;
> - gpio10 = &PIO9;
> - gpio11 = &PIO10;
> - gpio12 = &PIO11;
> - gpio13 = &PIO12;
> - gpio14 = &PIO30;
> - gpio15 = &PIO31;
> - gpio16 = &PIO13;
> - gpio17 = &PIO14;
> - gpio18 = &PIO15;
> - gpio19 = &PIO16;
> - gpio20 = &PIO17;
> - gpio21 = &PIO18;
> - gpio22 = &PIO100;
> - gpio23 = &PIO101;
> - gpio24 = &PIO102;
> - gpio25 = &PIO103;
> - gpio26 = &PIO104;
> - gpio27 = &PIO105;
> - gpio28 = &PIO106;
> - gpio29 = &PIO107;
> + gpio0 = &pio0;
> + gpio1 = &pio1;
> + gpio2 = &pio2;
> + gpio3 = &pio3;
> + gpio4 = &pio4;
> + gpio5 = &pio40;
> + gpio6 = &pio5;
> + gpio7 = &pio6;
> + gpio8 = &pio7;
> + gpio9 = &pio8;
> + gpio10 = &pio9;
> + gpio11 = &pio10;
> + gpio12 = &pio11;
> + gpio13 = &pio12;
> + gpio14 = &pio30;
> + gpio15 = &pio31;
> + gpio16 = &pio13;
> + gpio17 = &pio14;
> + gpio18 = &pio15;
> + gpio19 = &pio16;
> + gpio20 = &pio17;
> + gpio21 = &pio18;
> + gpio22 = &pio100;
> + gpio23 = &pio101;
> + gpio24 = &pio102;
> + gpio25 = &pio103;
> + gpio26 = &pio104;
> + gpio27 = &pio105;
> + gpio28 = &pio106;
> + gpio29 = &pio107;
> };
>
> soc {
> @@ -56,7 +56,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe610000 0x6000>;
>
> - PIO0: gpio at fe610000 {
> + pio0: gpio at fe610000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -64,7 +64,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO0";
> };
> - PIO1: gpio at fe611000 {
> + pio1: gpio at fe611000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -72,7 +72,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO1";
> };
> - PIO2: gpio at fe612000 {
> + pio2: gpio at fe612000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -80,7 +80,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO2";
> };
> - PIO3: gpio at fe613000 {
> + pio3: gpio at fe613000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -88,7 +88,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO3";
> };
> - PIO4: gpio at fe614000 {
> + pio4: gpio at fe614000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -96,7 +96,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO4";
> };
> - PIO40: gpio at fe615000 {
> + pio40: gpio at fe615000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -109,15 +109,15 @@
> rc{
> pinctrl_ir: ir0 {
> st,pins {
> - ir = <&PIO4 0 ALT2 IN>;
> + ir = <&pio4 0 ALT2 IN>;
> };
> };
> };
> sbc_serial1 {
> pinctrl_sbc_serial1: sbc_serial1 {
> st,pins {
> - tx = <&PIO2 6 ALT3 OUT>;
> - rx = <&PIO2 7 ALT3 IN>;
> + tx = <&pio2 6 ALT3 OUT>;
> + rx = <&pio2 7 ALT3 IN>;
> };
> };
> };
> @@ -125,15 +125,15 @@
> keyscan {
> pinctrl_keyscan: keyscan {
> st,pins {
> - keyin0 = <&PIO0 2 ALT2 IN>;
> - keyin1 = <&PIO0 3 ALT2 IN>;
> - keyin2 = <&PIO0 4 ALT2 IN>;
> - keyin3 = <&PIO2 6 ALT2 IN>;
> -
> - keyout0 = <&PIO1 6 ALT2 OUT>;
> - keyout1 = <&PIO1 7 ALT2 OUT>;
> - keyout2 = <&PIO0 6 ALT2 OUT>;
> - keyout3 = <&PIO2 7 ALT2 OUT>;
> + keyin0 = <&pio0 2 ALT2 IN>;
> + keyin1 = <&pio0 3 ALT2 IN>;
> + keyin2 = <&pio0 4 ALT2 IN>;
> + keyin3 = <&pio2 6 ALT2 IN>;
> +
> + keyout0 = <&pio1 6 ALT2 OUT>;
> + keyout1 = <&pio1 7 ALT2 OUT>;
> + keyout2 = <&pio0 6 ALT2 OUT>;
> + keyout3 = <&pio2 7 ALT2 OUT>;
> };
> };
> };
> @@ -141,8 +141,8 @@
> sbc_i2c0 {
> pinctrl_sbc_i2c0_default: sbc_i2c0-default {
> st,pins {
> - sda = <&PIO4 6 ALT1 BIDIR>;
> - scl = <&PIO4 5 ALT1 BIDIR>;
> + sda = <&pio4 6 ALT1 BIDIR>;
> + scl = <&pio4 5 ALT1 BIDIR>;
> };
> };
> };
> @@ -150,8 +150,8 @@
> sbc_i2c1 {
> pinctrl_sbc_i2c1_default: sbc_i2c1-default {
> st,pins {
> - sda = <&PIO3 2 ALT2 BIDIR>;
> - scl = <&PIO3 1 ALT2 BIDIR>;
> + sda = <&pio3 2 ALT2 BIDIR>;
> + scl = <&pio3 1 ALT2 BIDIR>;
> };
> };
> };
> @@ -159,51 +159,51 @@
> gmac1 {
> pinctrl_mii1: mii1 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> - col = <&PIO0 7 ALT1 IN BYPASS 1000>;
> -
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - crs = <&PIO1 2 ALT1 IN BYPASS 1000>;
> - mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
> - rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> -
> - rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> + col = <&pio0 7 ALT1 IN BYPASS 1000>;
> +
> + mdio = <&pio1 0 ALT1 OUT BYPASS 1500>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + crs = <&pio1 2 ALT1 IN BYPASS 1000>;
> + mdint = <&pio1 3 ALT1 IN BYPASS 0>;
> + rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> +
> + rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>;
> };
> };
> pinctrl_rgmii1: rgmii1-0 {
> st,pins {
> - txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
> - txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
> - txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
> - txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
> - txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>;
> - txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
> -
> - mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
> - mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
> - rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
> - rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
> - rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
> - rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
> -
> - rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>;
> - rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>;
> -
> - clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
> + txd0 = <&pio0 0 ALT1 OUT DE_IO 500 CLK_A>;
> + txd1 = <&pio0 1 ALT1 OUT DE_IO 500 CLK_A>;
> + txd2 = <&pio0 2 ALT1 OUT DE_IO 500 CLK_A>;
> + txd3 = <&pio0 3 ALT1 OUT DE_IO 500 CLK_A>;
> + txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
> + txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
> +
> + mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
> + mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
> + rxd0 = <&pio1 4 ALT1 IN DE_IO 500 CLK_A>;
> + rxd1 = <&pio1 5 ALT1 IN DE_IO 500 CLK_A>;
> + rxd2 = <&pio1 6 ALT1 IN DE_IO 500 CLK_A>;
> + rxd3 = <&pio1 7 ALT1 IN DE_IO 500 CLK_A>;
> +
> + rxdv = <&pio2 0 ALT1 IN DE_IO 500 CLK_A>;
> + rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio2 3 ALT4 OUT NICLK 0 CLK_B>;
> +
> + clk125= <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
> };
> };
> };
> @@ -220,7 +220,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfee00000 0x10000>;
>
> - PIO5: gpio at fee00000 {
> + pio5: gpio at fee00000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -228,7 +228,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO5";
> };
> - PIO6: gpio at fee01000 {
> + pio6: gpio at fee01000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -236,7 +236,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO6";
> };
> - PIO7: gpio at fee02000 {
> + pio7: gpio at fee02000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -244,7 +244,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO7";
> };
> - PIO8: gpio at fee03000 {
> + pio8: gpio at fee03000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -252,7 +252,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO8";
> };
> - PIO9: gpio at fee04000 {
> + pio9: gpio at fee04000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -260,7 +260,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO9";
> };
> - PIO10: gpio at fee05000 {
> + pio10: gpio at fee05000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -268,7 +268,7 @@
> reg = <0x5000 0x100>;
> st,bank-name = "PIO10";
> };
> - PIO11: gpio at fee06000 {
> + pio11: gpio at fee06000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -276,7 +276,7 @@
> reg = <0x6000 0x100>;
> st,bank-name = "PIO11";
> };
> - PIO12: gpio at fee07000 {
> + pio12: gpio at fee07000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -284,7 +284,7 @@
> reg = <0x7000 0x100>;
> st,bank-name = "PIO12";
> };
> - PIO30: gpio at fee08000 {
> + pio30: gpio at fee08000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -292,7 +292,7 @@
> reg = <0x8000 0x100>;
> st,bank-name = "PIO30";
> };
> - PIO31: gpio at fee09000 {
> + pio31: gpio at fee09000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -304,7 +304,7 @@
> serial2-oe {
> pinctrl_serial2_oe: serial2-1 {
> st,pins {
> - output-enable = <&PIO11 3 ALT2 OUT>;
> + output-enable = <&pio11 3 ALT2 OUT>;
> };
> };
> };
> @@ -312,8 +312,8 @@
> i2c0 {
> pinctrl_i2c0_default: i2c0-default {
> st,pins {
> - sda = <&PIO9 3 ALT1 BIDIR>;
> - scl = <&PIO9 2 ALT1 BIDIR>;
> + sda = <&pio9 3 ALT1 BIDIR>;
> + scl = <&pio9 2 ALT1 BIDIR>;
> };
> };
> };
> @@ -321,8 +321,8 @@
> i2c1 {
> pinctrl_i2c1_default: i2c1-default {
> st,pins {
> - sda = <&PIO12 1 ALT1 BIDIR>;
> - scl = <&PIO12 0 ALT1 BIDIR>;
> + sda = <&pio12 1 ALT1 BIDIR>;
> + scl = <&pio12 0 ALT1 BIDIR>;
> };
> };
> };
> @@ -330,12 +330,12 @@
> fsm {
> pinctrl_fsm: fsm {
> st,pins {
> - spi-fsm-clk = <&PIO12 2 ALT1 OUT>;
> - spi-fsm-cs = <&PIO12 3 ALT1 OUT>;
> - spi-fsm-mosi = <&PIO12 4 ALT1 OUT>;
> - spi-fsm-miso = <&PIO12 5 ALT1 IN>;
> - spi-fsm-hol = <&PIO12 6 ALT1 OUT>;
> - spi-fsm-wp = <&PIO12 7 ALT1 OUT>;
> + spi-fsm-clk = <&pio12 2 ALT1 OUT>;
> + spi-fsm-cs = <&pio12 3 ALT1 OUT>;
> + spi-fsm-mosi = <&pio12 4 ALT1 OUT>;
> + spi-fsm-miso = <&pio12 5 ALT1 IN>;
> + spi-fsm-hol = <&pio12 6 ALT1 OUT>;
> + spi-fsm-wp = <&pio12 7 ALT1 OUT>;
> };
> };
> };
> @@ -352,7 +352,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfe820000 0x6000>;
>
> - PIO13: gpio at fe820000 {
> + pio13: gpio at fe820000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -360,7 +360,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO13";
> };
> - PIO14: gpio at fe821000 {
> + pio14: gpio at fe821000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -368,7 +368,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO14";
> };
> - PIO15: gpio at fe822000 {
> + pio15: gpio at fe822000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -376,7 +376,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO15";
> };
> - PIO16: gpio at fe823000 {
> + pio16: gpio at fe823000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -384,7 +384,7 @@
> reg = <0x3000 0x100>;
> st,bank-name = "PIO16";
> };
> - PIO17: gpio at fe824000 {
> + pio17: gpio at fe824000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -392,7 +392,7 @@
> reg = <0x4000 0x100>;
> st,bank-name = "PIO17";
> };
> - PIO18: gpio at fe825000 {
> + pio18: gpio at fe825000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -405,8 +405,8 @@
> serial2 {
> pinctrl_serial2: serial2-0 {
> st,pins {
> - tx = <&PIO17 4 ALT2 OUT>;
> - rx = <&PIO17 5 ALT2 IN>;
> + tx = <&pio17 4 ALT2 OUT>;
> + rx = <&pio17 5 ALT2 IN>;
> };
> };
> };
> @@ -414,28 +414,28 @@
> gmac0 {
> pinctrl_mii0: mii0 {
> st,pins {
> - mdint = <&PIO13 6 ALT2 IN BYPASS 0>;
> - txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> -
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> - txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> - crs = <&PIO15 2 ALT2 IN BYPASS 1000>;
> - col = <&PIO15 3 ALT2 IN BYPASS 1000>;
> - mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> -
> - rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> - rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> - phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
> + mdint = <&pio13 6 ALT2 IN BYPASS 0>;
> + txen = <&pio13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd0 = <&pio14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
> +
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> + txer = <&pio15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
> + crs = <&pio15 2 ALT2 IN BYPASS 1000>;
> + col = <&pio15 3 ALT2 IN BYPASS 1000>;
> + mdio= <&pio15 4 ALT2 OUT BYPASS 1500>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> +
> + rxd0 = <&pio16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd1 = <&pio16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd2 = <&pio16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxd3 = <&pio16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxdv = <&pio15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rx_er = <&pio15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
> + rxclk = <&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT2 OUT NICLK 0 CLK_B>;
> };
> };
>
> @@ -445,25 +445,25 @@
> };
> pinctrl_rgmii0: rgmii0 {
> st,pins {
> - phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>;
> - txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
> - txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
> - txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
> - txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
> - txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
> - txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
> -
> - mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
> - mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
> -
> - rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
> - rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>;
> - rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>;
> - rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>;
> - rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
> - rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
> -
> - clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
> + phyclk = <&pio13 5 ALT4 OUT NICLK 0 CLK_B>;
> + txen = <&pio13 7 ALT2 OUT DE_IO 0 CLK_A>;
> + txd0 = <&pio14 0 ALT2 OUT DE_IO 500 CLK_A>;
> + txd1 = <&pio14 1 ALT2 OUT DE_IO 500 CLK_A>;
> + txd2 = <&pio14 2 ALT2 OUT DE_IO 500 CLK_B>;
> + txd3 = <&pio14 3 ALT2 OUT DE_IO 500 CLK_B>;
> + txclk = <&pio15 0 ALT2 IN NICLK 0 CLK_A>;
> +
> + mdio = <&pio15 4 ALT2 OUT BYPASS 0>;
> + mdc = <&pio15 5 ALT2 OUT NICLK 0 CLK_B>;
> +
> + rxdv = <&pio15 6 ALT2 IN DE_IO 500 CLK_A>;
> + rxd0 =<&pio16 0 ALT2 IN DE_IO 500 CLK_A>;
> + rxd1 =<&pio16 1 ALT2 IN DE_IO 500 CLK_A>;
> + rxd2 =<&pio16 2 ALT2 IN DE_IO 500 CLK_A>;
> + rxd3 =<&pio16 3 ALT2 IN DE_IO 500 CLK_A>;
> + rxclk =<&pio17 0 ALT2 IN NICLK 0 CLK_A>;
> +
> + clk125=<&pio17 6 ALT1 IN NICLK 0 CLK_A>;
> };
> };
> };
> @@ -480,7 +480,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd6b0000 0x3000>;
>
> - PIO100: gpio at fd6b0000 {
> + pio100: gpio at fd6b0000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -488,7 +488,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO100";
> };
> - PIO101: gpio at fd6b1000 {
> + pio101: gpio at fd6b1000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -496,7 +496,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO101";
> };
> - PIO102: gpio at fd6b2000 {
> + pio102: gpio at fd6b2000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -517,7 +517,7 @@
> interrupts-names = "irqmux";
> ranges = <0 0xfd330000 0x5000>;
>
> - PIO103: gpio at fd330000 {
> + pio103: gpio at fd330000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -525,7 +525,7 @@
> reg = <0 0x100>;
> st,bank-name = "PIO103";
> };
> - PIO104: gpio at fd331000 {
> + pio104: gpio at fd331000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -533,7 +533,7 @@
> reg = <0x1000 0x100>;
> st,bank-name = "PIO104";
> };
> - PIO105: gpio at fd332000 {
> + pio105: gpio at fd332000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -541,7 +541,7 @@
> reg = <0x2000 0x100>;
> st,bank-name = "PIO105";
> };
> - PIO106: gpio at fd333000 {
> + pio106: gpio at fd333000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> @@ -550,7 +550,7 @@
> st,bank-name = "PIO106";
> };
>
> - PIO107: gpio at fd334000 {
> + pio107: gpio at fd334000 {
> gpio-controller;
> #gpio-cells = <1>;
> interrupt-controller;
> diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi
> index b3dd6ca..5f91f45 100644
> --- a/arch/arm/boot/dts/stih41x-b2000.dtsi
> +++ b/arch/arm/boot/dts/stih41x-b2000.dtsi
> @@ -35,7 +35,7 @@
> fp_led {
> #gpio-cells = <1>;
> label = "Front Panel LED";
> - gpios = <&PIO105 7>;
> + gpios = <&pio105 7>;
> linux,default-trigger = "heartbeat";
> };
> };
> @@ -55,7 +55,7 @@
> phy-mode = "mii";
> pinctrl-0 = <&pinctrl_mii0>;
>
> - snps,reset-gpio = <&PIO106 2>;
> + snps,reset-gpio = <&pio106 2>;
> snps,reset-active-low;
> snps,reset-delays-us = <0 10000 10000>;
> };
> @@ -65,7 +65,7 @@
> phy-mode = "mii";
> st,tx-retime-src = "txclk";
>
> - snps,reset-gpio = <&PIO4 7>;
> + snps,reset-gpio = <&pio4 7>;
> snps,reset-active-low;
> snps,reset-delays-us = <0 10000 10000>;
> };
> diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi
> index d8a8429..c0f50e9 100644
> --- a/arch/arm/boot/dts/stih41x-b2020.dtsi
> +++ b/arch/arm/boot/dts/stih41x-b2020.dtsi
> @@ -32,11 +32,11 @@
> red {
> #gpio-cells = <1>;
> label = "Front Panel LED";
> - gpios = <&PIO4 1>;
> + gpios = <&pio4 1>;
> linux,default-trigger = "heartbeat";
> };
> green {
> - gpios = <&PIO4 7>;
> + gpios = <&pio4 7>;
> default-state = "off";
> };
> };
> @@ -68,7 +68,7 @@
> phy-mode = "rgmii-id";
> max-speed = <1000>;
> st,tx-retime-src = "clk_125";
> - snps,reset-gpio = <&PIO3 0>;
> + snps,reset-gpio = <&pio3 0>;
> snps,reset-active-low;
> snps,reset-delays-us = <0 10000 10000>;
>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
2014-06-25 14:53 ` Lee Jones
@ 2014-06-25 15:08 ` Maxime Coquelin
2014-06-25 15:26 ` Olof Johansson
0 siblings, 1 reply; 6+ messages in thread
From: Maxime Coquelin @ 2014-06-25 15:08 UTC (permalink / raw)
To: linux-arm-kernel
On 06/25/2014 04:53 PM, Lee Jones wrote:
>> Suggested-by: Olof Johansson <olof@lixom.net>
>> Signed-off-by: Lee Jones <lee.jones@linaro.org>
>> ---
>> arch/arm/boot/dts/stih415-pinctrl.dtsi | 340 +++++++++++++++---------------
>> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
>> arch/arm/boot/dts/stih416-pinctrl.dtsi | 342 +++++++++++++++----------------
>> arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
>> arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +-
>> 5 files changed, 350 insertions(+), 350 deletions(-)
>
> What happened to this Maxime?
>
> It was Acked by Olof, then died. Did it slip through the net?
>
You sent it to the ML after my last pull request for v3.16.
I think to take it for v3.17, but maybe you think it can go in next v3.16 rc?
If so, maybe Arnd or Olof can pick it directly, since we only have this single
patch for v3.16 fixes currently?
Anyway, you will have to rebase it I think, since stih416-b2020-revE.dts has
been renamed to stih416-b2020e.dts.
Don't hesitate to add my:
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Regards,
Maxime
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
2014-06-25 15:08 ` Maxime Coquelin
@ 2014-06-25 15:26 ` Olof Johansson
2014-06-25 15:37 ` Maxime Coquelin
0 siblings, 1 reply; 6+ messages in thread
From: Olof Johansson @ 2014-06-25 15:26 UTC (permalink / raw)
To: linux-arm-kernel
`On Wed, Jun 25, 2014 at 8:08 AM, Maxime Coquelin
<maxime.coquelin@st.com> wrote:
>
>
> On 06/25/2014 04:53 PM, Lee Jones wrote:
>>> Suggested-by: Olof Johansson <olof@lixom.net>
>>> Signed-off-by: Lee Jones <lee.jones@linaro.org>
>>> ---
>>> arch/arm/boot/dts/stih415-pinctrl.dtsi | 340 +++++++++++++++---------------
>>> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
>>> arch/arm/boot/dts/stih416-pinctrl.dtsi | 342 +++++++++++++++----------------
>>> arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
>>> arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +-
>>> 5 files changed, 350 insertions(+), 350 deletions(-)
>>
>> What happened to this Maxime?
>>
>> It was Acked by Olof, then died. Did it slip through the net?
>>
>
> You sent it to the ML after my last pull request for v3.16.
> I think to take it for v3.17, but maybe you think it can go in next v3.16 rc?
> If so, maybe Arnd or Olof can pick it directly, since we only have this single
> patch for v3.16 fixes currently?
If you have only one patch, then please send it to us as a fresh copy
with git send-email to arm at kernel.org + the usual lists.
You need to apply it and test it on hardware before anyway, right? We
certainly can't do that for you.
-Olof
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
2014-06-25 15:26 ` Olof Johansson
@ 2014-06-25 15:37 ` Maxime Coquelin
0 siblings, 0 replies; 6+ messages in thread
From: Maxime Coquelin @ 2014-06-25 15:37 UTC (permalink / raw)
To: linux-arm-kernel
Hi Olof,
On 06/25/2014 05:26 PM, Olof Johansson wrote:
> `On Wed, Jun 25, 2014 at 8:08 AM, Maxime Coquelin
> <maxime.coquelin@st.com> wrote:
>>
>>
>> On 06/25/2014 04:53 PM, Lee Jones wrote:
>>>> Suggested-by: Olof Johansson <olof@lixom.net> Signed-off-by:
>>>> Lee Jones <lee.jones@linaro.org> ---
>>>> arch/arm/boot/dts/stih415-pinctrl.dtsi | 340
>>>> +++++++++++++++---------------
>>>> arch/arm/boot/dts/stih416-b2020-revE.dts | 6 +-
>>>> arch/arm/boot/dts/stih416-pinctrl.dtsi | 342
>>>> +++++++++++++++----------------
>>>> arch/arm/boot/dts/stih41x-b2000.dtsi | 6 +-
>>>> arch/arm/boot/dts/stih41x-b2020.dtsi | 6 +- 5 files
>>>> changed, 350 insertions(+), 350 deletions(-)
>>>
>>> What happened to this Maxime?
>>>
>>> It was Acked by Olof, then died. Did it slip through the net?
>>>
>>
>> You sent it to the ML after my last pull request for v3.16. I
>> think to take it for v3.17, but maybe you think it can go in next
>> v3.16 rc? If so, maybe Arnd or Olof can pick it directly, since
>> we only have this single patch for v3.16 fixes currently?
>
> If you have only one patch, then please send it to us as a fresh
> copy with git send-email to arm at kernel.org + the usual lists.
>
> You need to apply it and test it on hardware before anyway, right?
> We certainly can't do that for you.
Sure, rebase and testing has to be done on our side.
I will add this patch to my queue for v3.17.
Regards,
Maxime
>
>
>
> -Olof
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-06-25 15:37 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-05-27 12:53 [PATCH] ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase Lee Jones
2014-05-27 18:01 ` Olof Johansson
2014-06-25 14:53 ` Lee Jones
2014-06-25 15:08 ` Maxime Coquelin
2014-06-25 15:26 ` Olof Johansson
2014-06-25 15:37 ` Maxime Coquelin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).