From: galak@codeaurora.org (Kumar Gala)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: dts: qcom: Update msm8660 device trees
Date: Wed, 28 May 2014 13:27:39 -0500 [thread overview]
Message-ID: <1401301659-20235-1-git-send-email-galak@codeaurora.org> (raw)
* Move SoC peripherals into an SoC container node
* Move serial enabling into board file (qcom-msm8660-surf.dts)
* Cleanup cpu node to match binding spec, enable-method and compatible
should be per cpu, not part of the container
Signed-off-by: Kumar Gala <galak@codeaurora.org>
---
arch/arm/boot/dts/qcom-msm8660-surf.dts | 6 ++
arch/arm/boot/dts/qcom-msm8660.dtsi | 104 +++++++++++++++++---------------
2 files changed, 63 insertions(+), 47 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
index 169bad9..13f5a78 100644
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
@@ -3,4 +3,10 @@
/ {
model = "Qualcomm MSM8660 SURF";
compatible = "qcom,msm8660-surf", "qcom,msm8660";
+
+ soc {
+ serial at 19c40000 {
+ status = "ok";
+ };
+ };
};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index c52a9e9..41bc38b 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -12,16 +12,18 @@
cpus {
#address-cells = <1>;
#size-cells = <0>;
- compatible = "qcom,scorpion";
- enable-method = "qcom,gcc-msm8660";
cpu at 0 {
+ compatible = "qcom,scorpion";
+ enable-method = "qcom,gcc-msm8660";
device_type = "cpu";
reg = <0>;
next-level-cache = <&L2>;
};
cpu at 1 {
+ compatible = "qcom,scorpion";
+ enable-method = "qcom,gcc-msm8660";
device_type = "cpu";
reg = <1>;
next-level-cache = <&L2>;
@@ -33,55 +35,63 @@
};
};
- intc: interrupt-controller at 2080000 {
- compatible = "qcom,msm-8660-qgic";
- interrupt-controller;
- #interrupt-cells = <3>;
- reg = < 0x02080000 0x1000 >,
- < 0x02081000 0x1000 >;
- };
+ soc: soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "simple-bus";
- timer at 2000000 {
- compatible = "qcom,scss-timer", "qcom,msm-timer";
- interrupts = <1 0 0x301>,
- <1 1 0x301>,
- <1 2 0x301>;
- reg = <0x02000000 0x100>;
- clock-frequency = <27000000>,
- <32768>;
- cpu-offset = <0x40000>;
- };
+ intc: interrupt-controller at 2080000 {
+ compatible = "qcom,msm-8660-qgic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = < 0x02080000 0x1000 >,
+ < 0x02081000 0x1000 >;
+ };
- msmgpio: gpio at 800000 {
- compatible = "qcom,msm-gpio";
- reg = <0x00800000 0x4000>;
- gpio-controller;
- #gpio-cells = <2>;
- ngpio = <173>;
- interrupts = <0 16 0x4>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
+ timer at 2000000 {
+ compatible = "qcom,scss-timer", "qcom,msm-timer";
+ interrupts = <1 0 0x301>,
+ <1 1 0x301>,
+ <1 2 0x301>;
+ reg = <0x02000000 0x100>;
+ clock-frequency = <27000000>,
+ <32768>;
+ cpu-offset = <0x40000>;
+ };
- gcc: clock-controller at 900000 {
- compatible = "qcom,gcc-msm8660";
- #clock-cells = <1>;
- #reset-cells = <1>;
- reg = <0x900000 0x4000>;
- };
+ msmgpio: gpio at 800000 {
+ compatible = "qcom,msm-gpio";
+ reg = <0x00800000 0x4000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpio = <173>;
+ interrupts = <0 16 0x4>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
- serial at 19c40000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x19c40000 0x1000>,
- <0x19c00000 0x1000>;
- interrupts = <0 195 0x0>;
- clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
- clock-names = "core", "iface";
- };
+ gcc: clock-controller at 900000 {
+ compatible = "qcom,gcc-msm8660";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ reg = <0x900000 0x4000>;
+ };
- qcom,ssbi at 500000 {
- compatible = "qcom,ssbi";
- reg = <0x500000 0x1000>;
- qcom,controller-type = "pmic-arbiter";
+ serial at 19c40000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x19c40000 0x1000>,
+ <0x19c00000 0x1000>;
+ interrupts = <0 195 0x0>;
+ clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ qcom,ssbi at 500000 {
+ compatible = "qcom,ssbi";
+ reg = <0x500000 0x1000>;
+ qcom,controller-type = "pmic-arbiter";
+ };
};
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
next reply other threads:[~2014-05-28 18:27 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-28 18:27 Kumar Gala [this message]
-- strict thread matches above, loose matches on Subject: below --
2014-05-29 15:40 [PATCH] ARM: dts: qcom: Update msm8660 device trees Kumar Gala
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1401301659-20235-1-git-send-email-galak@codeaurora.org \
--to=galak@codeaurora.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).