From: denis@eukrea.com (Denis Carikli)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v14 07/10] imx-drm: Use drm_display_mode timings flags.
Date: Mon, 16 Jun 2014 12:11:21 +0200 [thread overview]
Message-ID: <1402913484-25910-7-git-send-email-denis@eukrea.com> (raw)
In-Reply-To: <1402913484-25910-1-git-send-email-denis@eukrea.com>
The previous hardware behaviour was kept if the
flags are not set.
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
ChangeLog v13->v14:
- Rebased
ChangeLog v12->v13:
- This patch doesn't need the DRM_MODE_FLAG_POL_*_PRESERVE flags anymore.
- code cleanup to improve readability:
- ENABLE_POL_PRESERVE is now gone
- Less modifications in ipu_di_init_sync_panel
- more readable modifications in int ipu_crtc_mode_set
ChangeLog v11->v12:
- Rebased: It now uses the following new flags defines names:
CLK_POL, ENABLE_POL
- The inversions in ipuv3-crtc.c are now fixed.
- ipuv3-crtc.c was still using mode->private_flags
from the previous versions of this patchset, that's now fixed.
ChangeLog v10->v11:
- This patch was splitted-out and adapted from:
"Prepare imx-drm for extra display-timings retrival."
- The display-timings dt specific part was removed.
- The flags names were changed to use the DRM ones from:
"drm: drm_display_mode: add signal polarity flags"
---
drivers/gpu/ipu-v3/ipu-di.c | 2 ++
drivers/staging/imx-drm/ipuv3-crtc.c | 18 ++++++++++++++++--
include/video/imx-ipu-v3.h | 4 ++--
3 files changed, 20 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/ipu-v3/ipu-di.c b/drivers/gpu/ipu-v3/ipu-di.c
index d00f357..1a1e116 100644
--- a/drivers/gpu/ipu-v3/ipu-di.c
+++ b/drivers/gpu/ipu-v3/ipu-di.c
@@ -597,6 +597,8 @@ int ipu_di_init_sync_panel(struct ipu_di *di, struct ipu_di_signal_cfg *sig)
if (sig->clk_pol == CLK_POL_POSEDGE)
di_gen |= DI_GEN_POLARITY_DISP_CLK;
+ else if (sig->clk_pol == CLK_POL_NEGEDGE)
+ di_gen &= ~DI_GEN_POLARITY_DISP_CLK;
ipu_di_write(di, di_gen, DI_GENERAL);
diff --git a/drivers/staging/imx-drm/ipuv3-crtc.c b/drivers/staging/imx-drm/ipuv3-crtc.c
index 7fec438..7fdf575 100644
--- a/drivers/staging/imx-drm/ipuv3-crtc.c
+++ b/drivers/staging/imx-drm/ipuv3-crtc.c
@@ -165,8 +165,22 @@ static int ipu_crtc_mode_set(struct drm_crtc *crtc,
if (mode->flags & DRM_MODE_FLAG_PVSYNC)
sig_cfg.Vsync_pol = 1;
- sig_cfg.enable_pol = ENABLE_POL_HIGH;
- sig_cfg.clk_pol = CLK_POL_NEGEDGE;
+ if (mode->pol_flags & DRM_MODE_FLAG_POL_PIXDATA_POSEDGE)
+ sig_cfg.clk_pol = CLK_POL_POSEDGE;
+ else if (mode->pol_flags & DRM_MODE_FLAG_POL_PIXDATA_NEGEDGE)
+ sig_cfg.clk_pol = CLK_POL_NEGEDGE;
+ else
+ /* If no PIXDATA flags were set, keep the old behaviour */
+ sig_cfg.clk_pol = CLK_POL_NEGEDGE;
+
+ if (mode->pol_flags & DRM_MODE_FLAG_POL_DE_HIGH)
+ sig_cfg.enable_pol = ENABLE_POL_HIGH;
+ else if (mode->pol_flags & DRM_MODE_FLAG_POL_DE_LOW)
+ sig_cfg.enable_pol = ENABLE_POL_LOW;
+ else
+ /* If no DE flags were set, keep the old behaviour */
+ sig_cfg.enable_pol = ENABLE_POL_HIGH;
+
sig_cfg.width = mode->hdisplay;
sig_cfg.height = mode->vdisplay;
sig_cfg.pixel_fmt = out_pixel_fmt;
diff --git a/include/video/imx-ipu-v3.h b/include/video/imx-ipu-v3.h
index 8888305..e660522 100644
--- a/include/video/imx-ipu-v3.h
+++ b/include/video/imx-ipu-v3.h
@@ -43,10 +43,10 @@ struct ipu_di_signal_cfg {
unsigned clksel_en:1;
unsigned clkidle_en:1;
unsigned data_pol:1; /* true = inverted */
- unsigned clk_pol:1;
- unsigned enable_pol:1;
unsigned Hsync_pol:1; /* true = active high */
unsigned Vsync_pol:1;
+ u8 clk_pol;
+ u8 enable_pol;
u16 width;
u16 height;
--
1.7.9.5
next prev parent reply other threads:[~2014-06-16 10:11 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-06-16 10:11 [PATCH v14 01/10] [media] v4l2: add new V4L2_PIX_FMT_RGB666 pixel format Denis Carikli
2014-06-16 10:11 ` [PATCH v14 02/10] imx-drm: Add RGB666 support for parallel display Denis Carikli
2014-06-16 10:15 ` Russell King - ARM Linux
2014-06-16 10:11 ` [PATCH v14 03/10] imx-drm: Correct BGR666 and the board's dts that use them Denis Carikli
2014-06-16 10:15 ` Russell King - ARM Linux
2014-06-16 10:11 ` [PATCH v14 04/10] imx-drm: use defines for clock polarity settings Denis Carikli
2014-06-24 15:13 ` Russell King - ARM Linux
2014-06-24 16:25 ` Denis Carikli
2014-06-24 16:35 ` Russell King - ARM Linux
2014-06-25 4:48 ` Sascha Hauer
2014-06-25 8:43 ` Russell King - ARM Linux
2014-06-25 9:46 ` Sascha Hauer
2014-06-25 9:44 ` Denis Carikli
2014-06-26 20:56 ` Russell King - ARM Linux
2014-06-27 14:17 ` [PATCH v14 updated] " Denis Carikli
2014-06-16 10:11 ` [PATCH v14 05/10] ARM: dts: imx5*, imx6*: correct display-timings nodes Denis Carikli
2014-06-24 15:01 ` Russell King - ARM Linux
2014-06-25 2:29 ` Shawn Guo
2014-06-16 10:11 ` [PATCH v14 06/10] drm: drm_display_mode: add signal polarity flags Denis Carikli
2014-06-24 14:57 ` Russell King - ARM Linux
2014-06-24 22:13 ` Thierry Reding
2014-06-16 10:11 ` Denis Carikli [this message]
2014-06-25 9:20 ` [PATCH v14 07/10] imx-drm: Use drm_display_mode timings flags Russell King - ARM Linux
2014-06-16 10:11 ` [PATCH v14 08/10] drm/panel: Add Eukrea mbimxsd51 displays Denis Carikli
2014-06-24 15:06 ` Russell King - ARM Linux
2014-06-24 19:52 ` Rob Herring
2014-06-24 21:56 ` Thierry Reding
2014-06-25 9:42 ` Denis Carikli
2014-06-24 21:49 ` Thierry Reding
2014-06-24 21:56 ` Eric Bénard
2014-06-24 22:04 ` Thierry Reding
2014-06-25 8:27 ` Denis Carikli
2014-06-16 10:11 ` [PATCH v14 09/10] ARM: dts: mbimx51sd: Add display support Denis Carikli
2014-06-16 12:29 ` Denis Carikli
2014-06-17 13:46 ` Denis Carikli
2014-06-16 10:11 ` [PATCH v14 10/10] ARM: dts: mbimx51sd: Add CMO-QVGA backlight support Denis Carikli
2014-06-16 10:14 ` [PATCH v14 01/10] [media] v4l2: add new V4L2_PIX_FMT_RGB666 pixel format Russell King - ARM Linux
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1402913484-25910-7-git-send-email-denis@eukrea.com \
--to=denis@eukrea.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).