From: sr@denx.de (Stefan Roese)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/4 v2] arm: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
Date: Fri, 29 Aug 2014 12:40:04 +0200 [thread overview]
Message-ID: <1409308806-27036-2-git-send-email-sr@denx.de> (raw)
In-Reply-To: <1409308806-27036-1-git-send-email-sr@denx.de>
The Technexion TAO3530 is a OMAP3530 based SOM. This patch adds the
basic support for it as an dtsi file which can be included by
baseboard equipped with this SOM. E.g. the Technexion Thunder
baseboard.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
---
v2:
- Used OMAP3_CORE1_IOPAD macros for all mux entries
- Added ranges entry to gpmc node
- Added gpmc,device-width = <2> to nand dt node. Otherwise NAND probing
would not work
arch/arm/boot/dts/omap3-tao3530.dtsi | 337 +++++++++++++++++++++++++++++++++++
1 file changed, 337 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-tao3530.dtsi
diff --git a/arch/arm/boot/dts/omap3-tao3530.dtsi b/arch/arm/boot/dts/omap3-tao3530.dtsi
new file mode 100644
index 0000000..b30f387
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-tao3530.dtsi
@@ -0,0 +1,337 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "omap34xx-hs.dtsi"
+
+/ {
+ cpus {
+ cpu at 0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; /* gpio_162 */
+ vcc-supply = <&hsusb2_power>;
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "omap3beagle";
+
+ /* McBSP2 is used for onboard sound, same as on beagle */
+ ti,mcbsp = <&mcbsp2>;
+ ti,codec = <&twl_audio>;
+ };
+
+ /* Regulator to enable/switch the vcc of the Wifi module */
+ mmc2_sdio_poweron: regulator-mmc2-sdio-poweron {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-mmc2-sdio-poweron";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ gpio = <&gpio5 29 GPIO_ACTIVE_LOW>; /* gpio_157 */
+ enable-active-low;
+ startup-delay-us = <10000>;
+ };
+};
+
+&omap3_pmx_core {
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3_CORE1_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3_CORE1_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3_CORE1_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3_CORE1_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3_CORE1_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
+ OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
+ OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
+ OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
+ >;
+ };
+
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ /* wlan GPIO output for WLAN_EN */
+ wlan_gpio: pinmux_wlan_gpio {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr gpio_157 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl.i2c3_scl */
+ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda.i2c3_sda */
+ >;
+ };
+
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+
+ mcspi3_pins: pinmux_mcspi3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x25dc, PIN_OUTPUT | MUX_MODE1) /* etk_d0.mcspi3_simo gpio14 INPUT | MODE1 */
+ OMAP3_CORE1_IOPAD(0x25de, PIN_INPUT_PULLUP | MUX_MODE1) /* etk_d1.mcspi3_somi gpio15 INPUT | MODE1 */
+ OMAP3_CORE1_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE1) /* etk_d2.mcspi3_cs0 gpio16 INPUT | MODE1 */
+ OMAP3_CORE1_IOPAD(0x25e2, PIN_INPUT | MUX_MODE1) /* etk_d3.mcspi3_clk gpio17 INPUT | MODE1 */
+ >;
+ };
+
+ mcbsp3_pins: pinmux_mcbsp3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x216c, PIN_OUTPUT | MUX_MODE0) /* mcbsp3_dx.uart2_cts */
+ OMAP3_CORE1_IOPAD(0x216e, PIN_INPUT | MUX_MODE0) /* mcbsp3_dr.uart2_rts */
+ OMAP3_CORE1_IOPAD(0x2170, PIN_INPUT | MUX_MODE0) /* mcbsp3_clk.uart2_tx */
+ OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE0) /* mcbsp3_fsx.uart2_rx */
+ >;
+ };
+};
+
+/* McBSP1: mux'ed with GPIO158 as clock for HA-DSP */
+&mcbsp1 {
+ status = "disabled";
+};
+
+&mcbsp2 {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl at 48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+};
+
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+
+ spidev at 0 {
+ compatible = "spidev";
+ spi-max-frequency = <48000000>;
+ reg = <0>;
+ spi-cpha;
+ };
+};
+
+&mcspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi3_pins>;
+
+ spidev at 0 {
+ compatible = "spidev";
+ spi-max-frequency = <48000000>;
+ reg = <0>;
+ spi-cpha;
+ };
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ cd-gpios = <&twl_gpio 0 0>;
+ bus-width = <8>;
+};
+
+// WiFi (Marvell 88W8686) on MMC2/SDIO
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&mmc2_sdio_poweron>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
+&twl_gpio {
+ ti,use-leds;
+ /* pullups: BIT(1) */
+ ti,pullups = <0x000002>;
+ /*
+ * pulldowns:
+ * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+ * BIT(15), BIT(16), BIT(17)
+ */
+ ti,pulldowns = <0x03a1c4>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&mcbsp3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp3_pins>;
+};
+
+&gpmc {
+ ranges = <0 0 0x00000000 0x01000000>;
+
+ nand at 0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
+ ti,nand-ecc-opt = "sw";
+
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <36>;
+ gpmc,cs-wr-off-ns = <36>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <24>;
+ gpmc,adv-wr-off-ns = <36>;
+ gpmc,oe-on-ns = <6>;
+ gpmc,oe-off-ns = <48>;
+ gpmc,we-on-ns = <6>;
+ gpmc,we-off-ns = <30>;
+ gpmc,rd-cycle-ns = <72>;
+ gpmc,wr-cycle-ns = <72>;
+ gpmc,access-ns = <54>;
+ gpmc,wr-access-ns = <30>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ x-loader at 0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+
+ bootloaders at 80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ bootloaders_env at 260000 {
+ label = "U-Boot Env";
+ reg = <0x260000 0x20000>;
+ };
+
+ kernel at 280000 {
+ label = "Kernel";
+ reg = <0x280000 0x400000>;
+ };
+
+ filesystem at 680000 {
+ label = "File System";
+ reg = <0x680000 0xf980000>;
+ };
+ };
+};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
+
+&vaux2 {
+ regulator-name = "vdd_ehci";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
--
2.1.0
next prev parent reply other threads:[~2014-08-29 10:40 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-29 10:40 [PATCH 1/4 v2] arm: omap: tao3530: Add pdata-quirk for the mmc2 internal clock Stefan Roese
2014-08-29 10:40 ` Stefan Roese [this message]
2014-08-29 10:40 ` [PATCH 3/4 v2] arm: omap3: Add Technexion Thunder support (TAO3530 SOM based) Stefan Roese
2014-08-29 10:40 ` [PATCH 4/4 v2] arm: omap3: Add HEAD acoustics omap3-ha.dts and omap3-ha-lcd.dts (TAO3530 based) Stefan Roese
2014-09-09 0:09 ` [PATCH 1/4 v2] arm: omap: tao3530: Add pdata-quirk for the mmc2 internal clock Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1409308806-27036-2-git-send-email-sr@denx.de \
--to=sr@denx.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).