[PATCH V3 1/2] ARM: dts: Add DT changes for display on snow

[PATCH V3 1/2] ARM: dts: Add DT changes for display on snow

[Ajay Kumar]

Add DT nodes for ptn3460 bridge chip and panel.
Add backlight enable pin and backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on snow.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
---
Changes since V1:
	-- Remove "simple-panel" compatible string.
	-- Use GPIO_ACTIVE_HIGH instead of 0.
	-- Change panel node naming from "panel-simple" to "panel".

Changes since V2:
	-- Use proper compatible string: "auo,b116xw03"

 arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
 1 file changed, 22 insertions(+), 19 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index f2b8c41..1ac9709 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -9,6 +9,7 @@
 */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "exynos5250.dtsi"
 #include "exynos5250-cros-common.dtsi"
 
@@ -181,7 +182,7 @@
 					dcdc3 {
 						ti,enable-ext-control;
 					};
-					fet1 {
+					fet1: fet1 {
 						regulator-name = "vcd_led";
 						ti,overcurrent-wait = <3>;
 					};
@@ -204,7 +205,7 @@
 						regulator-always-on;
 						ti,overcurrent-wait = <3>;
 					};
-					fet6 {
+					fet6: fet6 {
 						regulator-name = "lcd_vdd";
 						ti,overcurrent-wait = <3>;
 					};
@@ -253,6 +254,15 @@
 			pinctrl-0 = <&max98095_en>;
 			pinctrl-names = "default";
 		};
+
+		ptn3460: lvds-bridge at 20 {
+			compatible = "nxp,ptn3460";
+			reg = <0x20>;
+			powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
+			edid-emulation = <5>;
+			panel = <&panel>;
+		};
 	};
 
 	i2s0: i2s at 03830000 {
@@ -300,11 +310,13 @@
 		vdd_pll-supply = <&ldo8_reg>;
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 1000000 0>;
 		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
 		default-brightness-level = <7>;
+		enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
+		power-supply = <&fet1>;
 		pinctrl-0 = <&pwm0_out>;
 		pinctrl-names = "default";
 	};
@@ -314,6 +326,12 @@
 		samsung,invert-vclk;
 	};
 
+	panel: panel {
+		compatible = "auo,b116xw03";
+		power-supply = <&fet6>;
+		backlight = <&backlight>;
+	};
+
 	dp-controller at 145B0000 {
 		status = "okay";
 		pinctrl-names = "default";
@@ -325,22 +343,7 @@
 		samsung,link-rate = <0x0a>;
 		samsung,lane-count = <2>;
 		samsung,hpd-gpio = <&gpx0 7 0>;
-
-		display-timings {
-			native-mode = <&timing1>;
-
-			timing1: timing at 1 {
-				clock-frequency = <70589280>;
-				hactive = <1366>;
-				vactive = <768>;
-				hfront-porch = <40>;
-				hback-porch = <40>;
-				hsync-len = <32>;
-				vback-porch = <10>;
-				vfront-porch = <12>;
-				vsync-len = <6>;
-			};
-		};
+		bridge = <&ptn3460>;
 	};
 };
 
-- 
1.7.9.5

[PATCH V3 2/2] ARM: dts: Add DT changes for display on peach_pit

[Ajay Kumar]

Add DT nodes for ps8622 bridge chip and panel.
Add backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on peach_pit.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
---
Changes since V1:
	-- Remove "simple-panel" compatible string.
	-- Use GPIO_ACTIVE_HIGH instead of 0.
	-- Change panel node naming from "panel-simple" to "panel".

Changes since V2:
	-- Use proper compatible string: "auo,b116xw03"

 arch/arm/boot/dts/exynos5420-peach-pit.dts |   36 +++++++++++++++-------------
 1 file changed, 19 insertions(+), 17 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 228a6b1..1070a31 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -30,11 +30,12 @@
 		i2c20 = "/spi at 12d40000/cros-ec at 0/i2c-tunnel";
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 1000000 0>;
 		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
 		default-brightness-level = <7>;
+		power-supply = <&tps65090_fet1>;
 		pinctrl-0 = <&pwm0_out>;
 		pinctrl-names = "default";
 	};
@@ -100,6 +101,12 @@
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	panel: panel {
+		compatible = "auo,b116xw03";
+		power-supply = <&tps65090_fet6>;
+		backlight = <&backlight>;
+	};
 };
 
 &dp {
@@ -113,22 +120,7 @@
 	samsung,link-rate = <0x06>;
 	samsung,lane-count = <2>;
 	samsung,hpd-gpio = <&gpx2 6 0>;
-
-	display-timings {
-		native-mode = <&timing1>;
-
-		timing1: timing at 1 {
-			clock-frequency = <70589280>;
-			hactive = <1366>;
-			vactive = <768>;
-			hfront-porch = <40>;
-			hback-porch = <40>;
-			hsync-len = <32>;
-			vback-porch = <10>;
-			vfront-porch = <12>;
-			vsync-len = <6>;
-		};
-	};
+	bridge = <&ps8625>;
 };
 
 &fimd {
@@ -155,6 +147,16 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&max98090_irq>;
 	};
+
+	ps8625: lvds-bridge at 48 {
+		compatible = "parade,ps8625";
+		reg = <0x48>;
+		sleep-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpy7 7 GPIO_ACTIVE_HIGH>;
+		lane-count = <2>;
+		panel = <&panel>;
+		use-external-pwm;
+	};
 };
 
 &hsi2c_9 {
-- 
1.7.9.5

[PATCH V3 1/2] ARM: dts: Add DT changes for display on snow

[Kukjin Kim]

On 09/01/14 19:36, Ajay Kumar wrote:
> Add DT nodes for ptn3460 bridge chip and panel.
> Add backlight enable pin and backlight power supply for pwm-backlight.
> Also add bridge phandle needed by dp to enable display on snow.
>
> Signed-off-by: Ajay Kumar<ajaykumar.rs@samsung.com>
> ---
> Changes since V1:
> 	-- Remove "simple-panel" compatible string.
> 	-- Use GPIO_ACTIVE_HIGH instead of 0.
> 	-- Change panel node naming from "panel-simple" to "panel".
>
> Changes since V2:
> 	-- Use proper compatible string: "auo,b116xw03"
>
>   arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
>   1 file changed, 22 insertions(+), 19 deletions(-)
>
Applied this and 2nd one.

BTW, I resolved conflict when I applied. Please check my tree and then 
if any problems, please let me know.

Thanks,
Kukjin

[PATCH V3 1/2] ARM: dts: Add DT changes for display on snow

[Ajay kumar]

Hi Kukjin,


On Sat, Sep 13, 2014 at 10:52 PM, Kukjin Kim <kgene.kim@samsung.com> wrote:
> On 09/01/14 19:36, Ajay Kumar wrote:
>>
>> Add DT nodes for ptn3460 bridge chip and panel.
>> Add backlight enable pin and backlight power supply for pwm-backlight.
>> Also add bridge phandle needed by dp to enable display on snow.
>>
>> Signed-off-by: Ajay Kumar<ajaykumar.rs@samsung.com>
>> ---
>> Changes since V1:
>>         -- Remove "simple-panel" compatible string.
>>         -- Use GPIO_ACTIVE_HIGH instead of 0.
>>         -- Change panel node naming from "panel-simple" to "panel".
>>
>> Changes since V2:
>>         -- Use proper compatible string: "auo,b116xw03"
>>
>>   arch/arm/boot/dts/exynos5250-snow.dts |   41
>> ++++++++++++++++++---------------
>>   1 file changed, 22 insertions(+), 19 deletions(-)
>>
> Applied this and 2nd one.
>
> BTW, I resolved conflict when I applied. Please check my tree and then if
> any problems, please let me know.

This patchset has dependency on driver patches.
But, no harm merging it since DT bindings are almost agreed.

The below patch should be merged ASAP. Because, driver changes are already in
for this patch:
https://www.mail-archive.com/linux-samsung-soc at vger.kernel.org/msg35182.html

Ajay