* [PATCH v4 01/10] ARM: add mach-asm9260
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 23:24 ` Rob Herring
2014-10-12 19:19 ` [PATCH v4 02/10] arm: add lolevel debug support for asm9260 Oleksij Rempel
` (8 subsequent siblings)
9 siblings, 1 reply; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
it is low cost (?) SoC targeted for market in China and India which
trying to compete with AT91SAM9G25.
Here is some info:
http://www.alphascale.com/index.asp?ics/615.html
One of products:
http://www.aliexpress.com/store/product/2014-hot-sales-FREE-SHIPPING-new-Purple-core-ARM9-development-board-ASM9260T-SDRAM-power-line/433637_1931495721.html
In some cases this SoC looks similar to iMX23/iMX28. But currently it makes no
sense to merge mach code of this devices. Especially because most differences
are already collected mach-mxs folder.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/arm/Kconfig | 2 ++
arch/arm/Makefile | 1 +
arch/arm/mach-asm9260/Kconfig | 8 ++++++++
arch/arm/mach-asm9260/Makefile | 1 +
arch/arm/mach-asm9260/core.c | 20 ++++++++++++++++++++
5 files changed, 32 insertions(+)
create mode 100644 arch/arm/mach-asm9260/Kconfig
create mode 100644 arch/arm/mach-asm9260/Makefile
create mode 100644 arch/arm/mach-asm9260/core.c
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5918d40..87373da 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -968,6 +968,8 @@ source "arch/arm/mach-w90x900/Kconfig"
source "arch/arm/mach-zynq/Kconfig"
+source "arch/arm/mach-asm9260/Kconfig"
+
# Definitions to make life easier
config ARCH_ACORN
bool
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 0ce9d0f..dda8f6d 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -146,6 +146,7 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
# Machine directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
machine-$(CONFIG_ARCH_AT91) += at91
+machine-$(CONFIG_MACH_ASM9260) += asm9260
machine-$(CONFIG_ARCH_AXXIA) += axxia
machine-$(CONFIG_ARCH_BCM) += bcm
machine-$(CONFIG_ARCH_BERLIN) += berlin
diff --git a/arch/arm/mach-asm9260/Kconfig b/arch/arm/mach-asm9260/Kconfig
new file mode 100644
index 0000000..eef90d9
--- /dev/null
+++ b/arch/arm/mach-asm9260/Kconfig
@@ -0,0 +1,8 @@
+config MACH_ASM9260
+ bool "Alphascale ASM9260"
+ depends on ARCH_MULTI_V5
+ select IRQ_MXS
+ select ASM9260_TIMER
+ select CPU_ARM926T
+ help
+ Support for Alpascale ASM9260 based platform.
diff --git a/arch/arm/mach-asm9260/Makefile b/arch/arm/mach-asm9260/Makefile
new file mode 100644
index 0000000..3f774e4
--- /dev/null
+++ b/arch/arm/mach-asm9260/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_MACH_ASM9260) += core.o
diff --git a/arch/arm/mach-asm9260/core.c b/arch/arm/mach-asm9260/core.c
new file mode 100644
index 0000000..d1b9006
--- /dev/null
+++ b/arch/arm/mach-asm9260/core.c
@@ -0,0 +1,20 @@
+/*
+ * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+
+static const char * const asm9260_dt_board_compat[] __initconst = {
+ "alphascale,asm9260",
+ NULL
+};
+
+DT_MACHINE_START(ASM9260, "Alphascale ASM9260 (Device Tree Support)")
+ .dt_compat = asm9260_dt_board_compat,
+MACHINE_END
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 01/10] ARM: add mach-asm9260
2014-10-12 19:19 ` [PATCH v4 01/10] ARM: add mach-asm9260 Oleksij Rempel
@ 2014-10-12 23:24 ` Rob Herring
2014-10-13 6:31 ` [PATCH v5 " Oleksij Rempel
0 siblings, 1 reply; 18+ messages in thread
From: Rob Herring @ 2014-10-12 23:24 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Oct 12, 2014 at 2:19 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> it is low cost (?) SoC targeted for market in China and India which
> trying to compete with AT91SAM9G25.
>
> Here is some info:
> http://www.alphascale.com/index.asp?ics/615.html
>
> One of products:
> http://www.aliexpress.com/store/product/2014-hot-sales-FREE-SHIPPING-new-Purple-core-ARM9-development-board-ASM9260T-SDRAM-power-line/433637_1931495721.html
>
> In some cases this SoC looks similar to iMX23/iMX28. But currently it makes no
> sense to merge mach code of this devices. Especially because most differences
> are already collected mach-mxs folder.
>
> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
> ---
> arch/arm/Kconfig | 2 ++
> arch/arm/Makefile | 1 +
> arch/arm/mach-asm9260/Kconfig | 8 ++++++++
> arch/arm/mach-asm9260/Makefile | 1 +
> arch/arm/mach-asm9260/core.c | 20 ++++++++++++++++++++
> 5 files changed, 32 insertions(+)
> create mode 100644 arch/arm/mach-asm9260/Kconfig
> create mode 100644 arch/arm/mach-asm9260/Makefile
> create mode 100644 arch/arm/mach-asm9260/core.c
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 5918d40..87373da 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -968,6 +968,8 @@ source "arch/arm/mach-w90x900/Kconfig"
>
> source "arch/arm/mach-zynq/Kconfig"
>
> +source "arch/arm/mach-asm9260/Kconfig"
> +
> # Definitions to make life easier
> config ARCH_ACORN
> bool
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index 0ce9d0f..dda8f6d 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -146,6 +146,7 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
> # Machine directory name. This list is sorted alphanumerically
> # by CONFIG_* macro name.
> machine-$(CONFIG_ARCH_AT91) += at91
> +machine-$(CONFIG_MACH_ASM9260) += asm9260
> machine-$(CONFIG_ARCH_AXXIA) += axxia
> machine-$(CONFIG_ARCH_BCM) += bcm
> machine-$(CONFIG_ARCH_BERLIN) += berlin
> diff --git a/arch/arm/mach-asm9260/Kconfig b/arch/arm/mach-asm9260/Kconfig
> new file mode 100644
> index 0000000..eef90d9
> --- /dev/null
> +++ b/arch/arm/mach-asm9260/Kconfig
> @@ -0,0 +1,8 @@
> +config MACH_ASM9260
> + bool "Alphascale ASM9260"
> + depends on ARCH_MULTI_V5
> + select IRQ_MXS
> + select ASM9260_TIMER
> + select CPU_ARM926T
> + help
> + Support for Alpascale ASM9260 based platform.
> diff --git a/arch/arm/mach-asm9260/Makefile b/arch/arm/mach-asm9260/Makefile
> new file mode 100644
> index 0000000..3f774e4
> --- /dev/null
> +++ b/arch/arm/mach-asm9260/Makefile
> @@ -0,0 +1 @@
> +obj-$(CONFIG_MACH_ASM9260) += core.o
> diff --git a/arch/arm/mach-asm9260/core.c b/arch/arm/mach-asm9260/core.c
> new file mode 100644
> index 0000000..d1b9006
> --- /dev/null
> +++ b/arch/arm/mach-asm9260/core.c
> @@ -0,0 +1,20 @@
> +/*
> + * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/of_platform.h>
> +#include <asm/mach/arch.h>
> +
> +static const char * const asm9260_dt_board_compat[] __initconst = {
> + "alphascale,asm9260",
> + NULL
> +};
> +
> +DT_MACHINE_START(ASM9260, "Alphascale ASM9260 (Device Tree Support)")
> + .dt_compat = asm9260_dt_board_compat,
> +MACHINE_END
You don't need this file as you are not doing anything special here.
Only the kconfig is needed.
Rob
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 02/10] arm: add lolevel debug support for asm9260
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 01/10] ARM: add mach-asm9260 Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 03/10] ARM: dts: add DT for Alphascale ASM9260 SoC Oleksij Rempel
` (7 subsequent siblings)
9 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/arm/Kconfig.debug | 33 ++++++++++++++++++++++++++++++---
arch/arm/include/debug/asm9260.S | 31 +++++++++++++++++++++++++++++++
2 files changed, 61 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/include/debug/asm9260.S
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index b11ad54..6902a57 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -953,6 +953,27 @@ choice
options; the platform specific options are deprecated
and will be soon removed.
+ config DEBUG_ASM9260_UART
+ bool "Kernel low-level debugging via asm9260 UART"
+ depends on MACH_ASM9260
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to an UART or USART port on asm9260 based
+ machines.
+
+ DEBUG_UART_PHYS | DEBUG_UART_VIRT
+
+ 0x80000000 | 0xf0000000 | UART0
+ 0x80004000 | 0xf0004000 | UART1
+ 0x80008000 | 0xf0008000 | UART2
+ 0x8000c000 | 0xf000c000 | UART3
+ 0x80010000 | 0xf0010000 | UART4
+ 0x80014000 | 0xf0014000 | UART5
+ 0x80018000 | 0xf0018000 | UART6
+ 0x8001c000 | 0xf001c000 | UART7
+ 0x80020000 | 0xf0020000 | UART8
+ 0x80024000 | 0xf0024000 | UART9
+
endchoice
config DEBUG_EXYNOS_UART
@@ -1038,6 +1059,7 @@ config DEBUG_LL_INCLUDE
default "debug/vf.S" if DEBUG_VF_UART
default "debug/vt8500.S" if DEBUG_VT8500_UART0
default "debug/zynq.S" if DEBUG_ZYNQ_UART0 || DEBUG_ZYNQ_UART1
+ default "debug/asm9260.S" if DEBUG_ASM9260_UART
default "mach/debug-macro.S"
# Compatibility options for PL01x
@@ -1094,6 +1116,7 @@ config DEBUG_UART_PHYS
default 0x50008000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART2 || \
DEBUG_S3C2410_UART2)
default 0x7c0003f8 if FOOTBRIDGE
+ default 0x80010000 if DEBUG_ASM9260_UART
default 0x80070000 if DEBUG_IMX23_UART
default 0x80074000 if DEBUG_IMX28_UART
default 0x80230000 if DEBUG_PICOXCELL_UART
@@ -1126,7 +1149,8 @@ config DEBUG_UART_PHYS
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
DEBUG_LL_UART_EFM32 || \
DEBUG_UART_8250 || DEBUG_UART_PL01X || \
- DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART
+ DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || \
+ DEBUG_S3C24XX_UART || DEBUG_ASM9260_UART
config DEBUG_UART_VIRT
hex "Virtual base address of debug UART"
@@ -1134,6 +1158,7 @@ config DEBUG_UART_VIRT
default 0xe1000000 if DEBUG_MSM_UART
default 0xf0000be0 if ARCH_EBSA110
default 0xf0009000 if DEBUG_CNS3XXX
+ default 0xf0010000 if DEBUG_ASM9260_UART
default 0xf01fb000 if DEBUG_NOMADIK_UART
default 0xf0201000 if DEBUG_BCM2835
default 0xf1000300 if DEBUG_BCM_5301X
@@ -1194,7 +1219,8 @@ config DEBUG_UART_VIRT
default DEBUG_UART_PHYS if !MMU
depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
DEBUG_UART_8250 || DEBUG_UART_PL01X || \
- DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART
+ DEBUG_MSM_UART || DEBUG_QCOM_UARTDM || \
+ DEBUG_S3C24XX_UART || DEBUG_ASM9260_UART
config DEBUG_UART_8250_SHIFT
int "Register offset shift for the 8250 debug UART"
@@ -1236,7 +1262,8 @@ config DEBUG_UNCOMPRESS
config UNCOMPRESS_INCLUDE
string
default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \
- PLAT_SAMSUNG || ARCH_EFM32
+ PLAT_SAMSUNG || ARCH_EFM32 || \
+ MACH_ASM9260
default "mach/uncompress.h"
config EARLY_PRINTK
diff --git a/arch/arm/include/debug/asm9260.S b/arch/arm/include/debug/asm9260.S
new file mode 100644
index 0000000..c70d51f
--- /dev/null
+++ b/arch/arm/include/debug/asm9260.S
@@ -0,0 +1,31 @@
+/* arch/arm/mach-imx/include/mach/debug-macro.S
+ *
+ * Debugging macro include header
+ *
+ * Copyright (C) 1994-1999 Russell King
+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ * Modified for ASM9260 by Oleksij Remepl <linux@rempel-privat.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+ .macro addruart, rp, rv, tmp
+ ldr \rp, = CONFIG_DEBUG_UART_PHYS
+ ldr \rv, = CONFIG_DEBUG_UART_VIRT
+ .endm
+
+ .macro waituart,rd,rx
+ .endm
+
+ .macro senduart,rd,rx
+ str \rd, [\rx, #0x50] @ TXDATA
+ .endm
+
+ .macro busyuart,rd,rx
+1002: ldr \rd, [\rx, #0x60] @ STAT
+ tst \rd, #1 << 27 @ TXEMPTY
+ beq 1002b @ wait until transmit done
+ .endm
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 03/10] ARM: dts: add DT for Alphascale ASM9260 SoC
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 01/10] ARM: add mach-asm9260 Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 02/10] arm: add lolevel debug support for asm9260 Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-13 10:18 ` Mark Rutland
2014-10-12 19:19 ` [PATCH v4 04/10] ARM: add alphascale,acc.txt bindings documentation Oleksij Rempel
` (6 subsequent siblings)
9 siblings, 1 reply; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
for now it is wary basic SoC description with most important IPs needed
to make this device work
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/alphascale-asm9260-devkit.dts | 21 ++++
arch/arm/boot/dts/alphascale-asm9260.dtsi | 134 ++++++++++++++++++++++++
include/dt-bindings/clock/alphascale,asm9260.h | 97 +++++++++++++++++
4 files changed, 254 insertions(+)
create mode 100644 arch/arm/boot/dts/alphascale-asm9260-devkit.dts
create mode 100644 arch/arm/boot/dts/alphascale-asm9260.dtsi
create mode 100644 include/dt-bindings/clock/alphascale,asm9260.h
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b8c5cd3..8943d72 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -492,6 +492,8 @@ dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
dove-d3plug.dtb \
dove-dove-db.dtb
+dtb-$(CONFIG_MACH_ASM9260) += alphascale-asm9260-devkit.dtb
+
targets += dtbs dtbs_install
targets += $(dtb-y)
endif
diff --git a/arch/arm/boot/dts/alphascale-asm9260-devkit.dts b/arch/arm/boot/dts/alphascale-asm9260-devkit.dts
new file mode 100644
index 0000000..bf63dd2
--- /dev/null
+++ b/arch/arm/boot/dts/alphascale-asm9260-devkit.dts
@@ -0,0 +1,21 @@
+/*
+ * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * Licensed under the X11 license or the GPL v2 (or later)
+ */
+
+/dts-v1/;
+#include "alphascale-asm9260.dtsi"
+
+/ {
+ model = "Alphascale asm9260 Development Kit";
+ compatible = "alphascale,asm9260devkit", "alphascale,asm9260";
+
+ aliases {
+ serial0 = &uart4;
+ };
+};
+
+&uart4 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/alphascale-asm9260.dtsi b/arch/arm/boot/dts/alphascale-asm9260.dtsi
new file mode 100644
index 0000000..d147612
--- /dev/null
+++ b/arch/arm/boot/dts/alphascale-asm9260.dtsi
@@ -0,0 +1,134 @@
+/*
+ * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * Licensed under the X11 license or the GPL v2 (or later)
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/alphascale,asm9260.h>
+
+/ {
+ interrupt-parent = <&icoll>;
+
+ memory {
+ device_type = "memory";
+ reg = <0x20000000 0x2000000>;
+ };
+
+ cpus {
+ #address-cells = <0>;
+ #size-cells = <0>;
+
+ cpu {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ clocks = <&acc CLKID_SYS_CPU>;
+ };
+ };
+
+ osc24m: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-accuracy = <30000>;
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges;
+
+ acc: clock-controller at 80040000 {
+ compatible = "alphascale,asm9260-clock-controller";
+ #clock-cells = <1>;
+ clocks = <&osc24m>;
+ reg = <0x80040000 0x204>;
+ };
+
+ icoll: interrupt-controller at 80054000 {
+ compatible = "alphascale,asm9260-icoll";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x80054000 0x200>;
+ };
+
+ uart0: serial at 80000000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80000000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART0>, <&acc CLKID_AHB_UART0>;
+ interrupts = <15>;
+ status = "disabled";
+ };
+ uart1: serial at 80004000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80004000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART1>, <&acc CLKID_AHB_UART1>;
+ interrupts = <16>;
+ status = "disabled";
+ };
+ uart2: serial at 80008000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80008000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART2>, <&acc CLKID_AHB_UART2>;
+ interrupts = <17>;
+ status = "disabled";
+ };
+ uart3: serial at 8000c000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x8000c000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART3>, <&acc CLKID_AHB_UART3>;
+ interrupts = <18>;
+ status = "disabled";
+ };
+ uart4: serial at 80010000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80010000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART4>, <&acc CLKID_AHB_UART4>;
+ interrupts = <19>;
+ status = "disabled";
+ };
+ uart5: serial at 80014000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80014000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART5>, <&acc CLKID_AHB_UART5>;
+ interrupts = <20>;
+ status = "disabled";
+ };
+ uart6: serial at 80018000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80018000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART6>, <&acc CLKID_AHB_UART6>;
+ interrupts = <21>;
+ status = "disabled";
+ };
+ uart7: serial at 8001c000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x8001c000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART7>, <&acc CLKID_AHB_UART7>;
+ interrupts = <22>;
+ status = "disabled";
+ };
+ uart8: serial at 80020000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80020000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART8>, <&acc CLKID_AHB_UART8>;
+ interrupts = <23>;
+ status = "disabled";
+ };
+ uart9: serial at 80024000 {
+ compatible = "alphascale,asm9260-auart";
+ reg = <0x80024000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART9>, <&acc CLKID_AHB_UART9>;
+ interrupts = <24>;
+ status = "disabled";
+ };
+
+ timer0: timer at 80088000 {
+ compatible = "alphascale,asm9260-timer";
+ reg = <0x80088000 0x4000>;
+ clocks = <&acc CLKID_AHB_TIMER0>;
+ interrupts = <29>;
+ };
+ };
+};
diff --git a/include/dt-bindings/clock/alphascale,asm9260.h b/include/dt-bindings/clock/alphascale,asm9260.h
new file mode 100644
index 0000000..04e8db2
--- /dev/null
+++ b/include/dt-bindings/clock/alphascale,asm9260.h
@@ -0,0 +1,97 @@
+/*
+ * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_ASM9260_H
+#define _DT_BINDINGS_CLK_ASM9260_H
+
+/* ahb gate */
+#define CLKID_AHB_ROM 0
+#define CLKID_AHB_RAM 1
+#define CLKID_AHB_GPIO 2
+#define CLKID_AHB_MAC 3
+#define CLKID_AHB_EMI 4
+#define CLKID_AHB_USB0 5
+#define CLKID_AHB_USB1 6
+#define CLKID_AHB_DMA0 7
+#define CLKID_AHB_DMA1 8
+#define CLKID_AHB_UART0 9
+#define CLKID_AHB_UART1 10
+#define CLKID_AHB_UART2 11
+#define CLKID_AHB_UART3 12
+#define CLKID_AHB_UART4 13
+#define CLKID_AHB_UART5 14
+#define CLKID_AHB_UART6 15
+#define CLKID_AHB_UART7 16
+#define CLKID_AHB_UART8 17
+#define CLKID_AHB_UART9 18
+#define CLKID_AHB_I2S0 19
+#define CLKID_AHB_I2C0 20
+#define CLKID_AHB_I2C1 21
+#define CLKID_AHB_SSP0 22
+#define CLKID_AHB_IOCONFIG 23
+#define CLKID_AHB_WDT 24
+#define CLKID_AHB_CAN0 25
+#define CLKID_AHB_CAN1 26
+#define CLKID_AHB_MPWM 27
+#define CLKID_AHB_SPI0 28
+#define CLKID_AHB_SPI1 29
+#define CLKID_AHB_QEI 30
+#define CLKID_AHB_QUADSPI0 31
+#define CLKID_AHB_CAMIF 32
+#define CLKID_AHB_LCDIF 33
+#define CLKID_AHB_TIMER0 34
+#define CLKID_AHB_TIMER1 35
+#define CLKID_AHB_TIMER2 36
+#define CLKID_AHB_TIMER3 37
+#define CLKID_AHB_IRQ 38
+#define CLKID_AHB_RTC 39
+#define CLKID_AHB_NAND 40
+#define CLKID_AHB_ADC0 41
+#define CLKID_AHB_LED 42
+#define CLKID_AHB_DAC0 43
+#define CLKID_AHB_LCD 44
+#define CLKID_AHB_I2S1 45
+#define CLKID_AHB_MAC1 46
+
+/* devider */
+#define CLKID_SYS_CPU 47
+#define CLKID_SYS_AHB 48
+#define CLKID_SYS_I2S0M 49
+#define CLKID_SYS_I2S0S 50
+#define CLKID_SYS_I2S1M 51
+#define CLKID_SYS_I2S1S 52
+#define CLKID_SYS_UART0 53
+#define CLKID_SYS_UART1 54
+#define CLKID_SYS_UART2 55
+#define CLKID_SYS_UART3 56
+#define CLKID_SYS_UART4 56
+#define CLKID_SYS_UART5 57
+#define CLKID_SYS_UART6 58
+#define CLKID_SYS_UART7 59
+#define CLKID_SYS_UART8 60
+#define CLKID_SYS_UART9 61
+#define CLKID_SYS_SPI0 62
+#define CLKID_SYS_SPI1 63
+#define CLKID_SYS_QUADSPI 64
+#define CLKID_SYS_SSP0 65
+#define CLKID_SYS_NAND 66
+#define CLKID_SYS_TRACE 67
+#define CLKID_SYS_CAMM 68
+#define CLKID_SYS_WDT 69
+#define CLKID_SYS_CLKOUT 70
+#define CLKID_SYS_MAC 71
+#define CLKID_SYS_LCD 72
+#define CLKID_SYS_ADCANA 73
+
+#define MAX_CLKS 74
+#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 03/10] ARM: dts: add DT for Alphascale ASM9260 SoC
2014-10-12 19:19 ` [PATCH v4 03/10] ARM: dts: add DT for Alphascale ASM9260 SoC Oleksij Rempel
@ 2014-10-13 10:18 ` Mark Rutland
0 siblings, 0 replies; 18+ messages in thread
From: Mark Rutland @ 2014-10-13 10:18 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Oct 12, 2014 at 08:19:14PM +0100, Oleksij Rempel wrote:
> for now it is wary basic SoC description with most important IPs needed
> to make this device work
>
> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
> ---
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/alphascale-asm9260-devkit.dts | 21 ++++
> arch/arm/boot/dts/alphascale-asm9260.dtsi | 134 ++++++++++++++++++++++++
> include/dt-bindings/clock/alphascale,asm9260.h | 97 +++++++++++++++++
> 4 files changed, 254 insertions(+)
> create mode 100644 arch/arm/boot/dts/alphascale-asm9260-devkit.dts
> create mode 100644 arch/arm/boot/dts/alphascale-asm9260.dtsi
> create mode 100644 include/dt-bindings/clock/alphascale,asm9260.h
This last file should go with the clock controller driver/binding, which
should come before this patch.
[...]
> + soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "simple-bus";
> + ranges;
There seems to be odd whitespace before the ranges property.
Thanks,
Mark.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 04/10] ARM: add alphascale,acc.txt bindings documentation
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (2 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 03/10] ARM: dts: add DT for Alphascale ASM9260 SoC Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-13 10:21 ` Mark Rutland
2014-10-12 19:19 ` [PATCH v4 05/10] ARM: clk: add clk-asm9260 driver Oleksij Rempel
` (5 subsequent siblings)
9 siblings, 1 reply; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
ACC is for AlphaScale Clock Controller.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
.../devicetree/bindings/clock/alphascale,acc.txt | 113 +++++++++++++++++++++
1 file changed, 113 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/alphascale,acc.txt
diff --git a/Documentation/devicetree/bindings/clock/alphascale,acc.txt b/Documentation/devicetree/bindings/clock/alphascale,acc.txt
new file mode 100644
index 0000000..92a03a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/alphascale,acc.txt
@@ -0,0 +1,113 @@
+Alphascale Clock Controller
+
+The ACC (Alphascale Clock Controller) is responsible of choising proper
+clock source, setting deviders and clock gates.
+
+Required properties for the ACC node:
+- compatible: must be "alphascale,asm9260-clock-controller"
+- reg: must contain the ACC register base and size
+
+ACC allow peripheral clocks to be gated to save some power. The clock consumer
+should specify the desired clock by having the clock ID in it
+"clocks" phandle cell. It is encouraged to use dt-binding for clock ID
+definitions. SoC specific dt-binding should be included to the device tree
+descriptor. For example Alphascale ASM9260:
+#include <dt-bindings/clock/alphascale,asm9260.h>
+
+This binding contains two types of clock sinks: _AHB_ sink - a peripheral
+gate; _SYS_ sink - an adjustable clock source. Not all clock consumer
+have _SYS_ sink. All sink details can be found in the SoC documentation.
+CLKID_AHB_ROM 0
+CLKID_AHB_RAM 1
+CLKID_AHB_GPIO 2
+CLKID_AHB_MAC 3
+CLKID_AHB_EMI 4
+CLKID_AHB_USB0 5
+CLKID_AHB_USB1 6
+CLKID_AHB_DMA0 7
+CLKID_AHB_DMA1 8
+CLKID_AHB_UART0 9
+CLKID_AHB_UART1 10
+CLKID_AHB_UART2 11
+CLKID_AHB_UART3 12
+CLKID_AHB_UART4 13
+CLKID_AHB_UART5 14
+CLKID_AHB_UART6 15
+CLKID_AHB_UART7 16
+CLKID_AHB_UART8 17
+CLKID_AHB_UART9 18
+CLKID_AHB_I2S0 19
+CLKID_AHB_I2C0 20
+CLKID_AHB_I2C1 21
+CLKID_AHB_SSP0 22
+CLKID_AHB_IOCONFIG 23
+CLKID_AHB_WDT 24
+CLKID_AHB_CAN0 25
+CLKID_AHB_CAN1 26
+CLKID_AHB_MPWM 27
+CLKID_AHB_SPI0 28
+CLKID_AHB_SPI1 29
+CLKID_AHB_QEI 30
+CLKID_AHB_QUADSPI0 31
+CLKID_AHB_CAMIF 32
+CLKID_AHB_LCDIF 33
+CLKID_AHB_TIMER0 34
+CLKID_AHB_TIMER1 35
+CLKID_AHB_TIMER2 36
+CLKID_AHB_TIMER3 37
+CLKID_AHB_IRQ 38
+CLKID_AHB_RTC 39
+CLKID_AHB_NAND 40
+CLKID_AHB_ADC0 41
+CLKID_AHB_LED 42
+CLKID_AHB_DAC0 43
+CLKID_AHB_LCD 44
+CLKID_AHB_I2S1 45
+CLKID_AHB_MAC1 46
+
+CLKID_SYS_CPU 47
+CLKID_SYS_AHB 48
+CLKID_SYS_I2S0M 49
+CLKID_SYS_I2S0S 50
+CLKID_SYS_I2S1M 51
+CLKID_SYS_I2S1S 52
+CLKID_SYS_UART0 53
+CLKID_SYS_UART1 54
+CLKID_SYS_UART2 55
+CLKID_SYS_UART3 56
+CLKID_SYS_UART4 56
+CLKID_SYS_UART5 57
+CLKID_SYS_UART6 58
+CLKID_SYS_UART7 59
+CLKID_SYS_UART8 60
+CLKID_SYS_UART9 61
+CLKID_SYS_SPI0 62
+CLKID_SYS_SPI1 63
+CLKID_SYS_QUADSPI 64
+CLKID_SYS_SSP0 65
+CLKID_SYS_NAND 66
+CLKID_SYS_TRACE 67
+CLKID_SYS_CAMM 68
+CLKID_SYS_WDT 69
+CLKID_SYS_CLKOUT 70
+CLKID_SYS_MAC 71
+CLKID_SYS_LCD 72
+CLKID_SYS_ADCANA 73
+
+Example of clock consumer with _SYS_ and _AHB_ sinks.
+uart4: serial at 80010000 {
+ compatible = "alphascale,asm9260-uart";
+ reg = <0x80010000 0x4000>;
+ clocks = <&acc CLKID_SYS_UART4>, <&acc CLKID_AHB_UART4>;
+ interrupts = <19>;
+ status = "disabled";
+};
+
+Clock consumer with only one, _AHB_ sink.
+timer0: timer at 80088000 {
+ compatible = "alphascale,asm9260-timer";
+ reg = <0x80088000 0x4000>;
+ clocks = <&acc CLKID_AHB_TIMER0>;
+ interrupts = <29>;
+};
+
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 04/10] ARM: add alphascale,acc.txt bindings documentation
2014-10-12 19:19 ` [PATCH v4 04/10] ARM: add alphascale,acc.txt bindings documentation Oleksij Rempel
@ 2014-10-13 10:21 ` Mark Rutland
0 siblings, 0 replies; 18+ messages in thread
From: Mark Rutland @ 2014-10-13 10:21 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Oct 12, 2014 at 08:19:15PM +0100, Oleksij Rempel wrote:
> ACC is for AlphaScale Clock Controller.
>
> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
> ---
> .../devicetree/bindings/clock/alphascale,acc.txt | 113 +++++++++++++++++++++
> 1 file changed, 113 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/alphascale,acc.txt
>
> diff --git a/Documentation/devicetree/bindings/clock/alphascale,acc.txt b/Documentation/devicetree/bindings/clock/alphascale,acc.txt
> new file mode 100644
> index 0000000..92a03a5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/alphascale,acc.txt
> @@ -0,0 +1,113 @@
> +Alphascale Clock Controller
> +
> +The ACC (Alphascale Clock Controller) is responsible of choising proper
> +clock source, setting deviders and clock gates.
> +
> +Required properties for the ACC node:
> +- compatible: must be "alphascale,asm9260-clock-controller"
> +- reg: must contain the ACC register base and size
I take it you expect #clock-cells to be 1, and for the cell to be one of
the values below. Please point this out explictly here.
> +
> +ACC allow peripheral clocks to be gated to save some power. The clock consumer
> +should specify the desired clock by having the clock ID in it
> +"clocks" phandle cell. It is encouraged to use dt-binding for clock ID
The ID is in the clock-specifier (a tuple of cells defined by
#clock-cells), not the phandle.
> +definitions. SoC specific dt-binding should be included to the device tree
> +descriptor. For example Alphascale ASM9260:
> +#include <dt-bindings/clock/alphascale,asm9260.h>
> +
> +This binding contains two types of clock sinks: _AHB_ sink - a peripheral
> +gate; _SYS_ sink - an adjustable clock source. Not all clock consumer
> +have _SYS_ sink. All sink details can be found in the SoC documentation.
These should be described in terms of the clock provider, not the
consumer.
Thanks,
Mark.
> +CLKID_AHB_ROM 0
> +CLKID_AHB_RAM 1
> +CLKID_AHB_GPIO 2
> +CLKID_AHB_MAC 3
> +CLKID_AHB_EMI 4
> +CLKID_AHB_USB0 5
> +CLKID_AHB_USB1 6
> +CLKID_AHB_DMA0 7
> +CLKID_AHB_DMA1 8
> +CLKID_AHB_UART0 9
> +CLKID_AHB_UART1 10
> +CLKID_AHB_UART2 11
> +CLKID_AHB_UART3 12
> +CLKID_AHB_UART4 13
> +CLKID_AHB_UART5 14
> +CLKID_AHB_UART6 15
> +CLKID_AHB_UART7 16
> +CLKID_AHB_UART8 17
> +CLKID_AHB_UART9 18
> +CLKID_AHB_I2S0 19
> +CLKID_AHB_I2C0 20
> +CLKID_AHB_I2C1 21
> +CLKID_AHB_SSP0 22
> +CLKID_AHB_IOCONFIG 23
> +CLKID_AHB_WDT 24
> +CLKID_AHB_CAN0 25
> +CLKID_AHB_CAN1 26
> +CLKID_AHB_MPWM 27
> +CLKID_AHB_SPI0 28
> +CLKID_AHB_SPI1 29
> +CLKID_AHB_QEI 30
> +CLKID_AHB_QUADSPI0 31
> +CLKID_AHB_CAMIF 32
> +CLKID_AHB_LCDIF 33
> +CLKID_AHB_TIMER0 34
> +CLKID_AHB_TIMER1 35
> +CLKID_AHB_TIMER2 36
> +CLKID_AHB_TIMER3 37
> +CLKID_AHB_IRQ 38
> +CLKID_AHB_RTC 39
> +CLKID_AHB_NAND 40
> +CLKID_AHB_ADC0 41
> +CLKID_AHB_LED 42
> +CLKID_AHB_DAC0 43
> +CLKID_AHB_LCD 44
> +CLKID_AHB_I2S1 45
> +CLKID_AHB_MAC1 46
> +
> +CLKID_SYS_CPU 47
> +CLKID_SYS_AHB 48
> +CLKID_SYS_I2S0M 49
> +CLKID_SYS_I2S0S 50
> +CLKID_SYS_I2S1M 51
> +CLKID_SYS_I2S1S 52
> +CLKID_SYS_UART0 53
> +CLKID_SYS_UART1 54
> +CLKID_SYS_UART2 55
> +CLKID_SYS_UART3 56
> +CLKID_SYS_UART4 56
> +CLKID_SYS_UART5 57
> +CLKID_SYS_UART6 58
> +CLKID_SYS_UART7 59
> +CLKID_SYS_UART8 60
> +CLKID_SYS_UART9 61
> +CLKID_SYS_SPI0 62
> +CLKID_SYS_SPI1 63
> +CLKID_SYS_QUADSPI 64
> +CLKID_SYS_SSP0 65
> +CLKID_SYS_NAND 66
> +CLKID_SYS_TRACE 67
> +CLKID_SYS_CAMM 68
> +CLKID_SYS_WDT 69
> +CLKID_SYS_CLKOUT 70
> +CLKID_SYS_MAC 71
> +CLKID_SYS_LCD 72
> +CLKID_SYS_ADCANA 73
> +
> +Example of clock consumer with _SYS_ and _AHB_ sinks.
> +uart4: serial at 80010000 {
> + compatible = "alphascale,asm9260-uart";
> + reg = <0x80010000 0x4000>;
> + clocks = <&acc CLKID_SYS_UART4>, <&acc CLKID_AHB_UART4>;
> + interrupts = <19>;
> + status = "disabled";
> +};
> +
> +Clock consumer with only one, _AHB_ sink.
> +timer0: timer at 80088000 {
> + compatible = "alphascale,asm9260-timer";
> + reg = <0x80088000 0x4000>;
> + clocks = <&acc CLKID_AHB_TIMER0>;
> + interrupts = <29>;
> +};
> +
> --
> 1.9.1
>
>
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 05/10] ARM: clk: add clk-asm9260 driver
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (3 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 04/10] ARM: add alphascale,acc.txt bindings documentation Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 06/10] clocksource: add asm9260_timer driver Oleksij Rempel
` (4 subsequent siblings)
9 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
Provide CLK support for Alphascale ASM9260 SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
drivers/clk/Makefile | 1 +
drivers/clk/clk-asm9260.c | 351 ++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 352 insertions(+)
create mode 100644 drivers/clk/clk-asm9260.c
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index f537a0b..45bbf22 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_ARCH_HI3xxx) += hisilicon/
obj-$(CONFIG_ARCH_HIP04) += hisilicon/
obj-$(CONFIG_ARCH_HIX5HD2) += hisilicon/
obj-$(CONFIG_COMMON_CLK_KEYSTONE) += keystone/
+obj-$(CONFIG_MACH_ASM9260) += clk-asm9260.o
ifeq ($(CONFIG_COMMON_CLK), y)
obj-$(CONFIG_ARCH_MMP) += mmp/
endif
diff --git a/drivers/clk/clk-asm9260.c b/drivers/clk/clk-asm9260.c
new file mode 100644
index 0000000..9ef4e8d
--- /dev/null
+++ b/drivers/clk/clk-asm9260.c
@@ -0,0 +1,351 @@
+/*
+ * Copyright (c) 2014 Oleksij Rempel <linux@rempel-privat.de>.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk-provider.h>
+#include <linux/spinlock.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <dt-bindings/clock/alphascale,asm9260.h>
+
+#define HW_AHBCLKCTRL0 0x0020
+#define HW_AHBCLKCTRL1 0x0030
+#define HW_SYSPLLCTRL 0x0100
+#define HW_MAINCLKSEL 0x0120
+#define HW_MAINCLKUEN 0x0124
+#define HW_UARTCLKSEL 0x0128
+#define HW_UARTCLKUEN 0x012c
+#define HW_I2S0CLKSEL 0x0130
+#define HW_I2S0CLKUEN 0x0134
+#define HW_I2S1CLKSEL 0x0138
+#define HW_I2S1CLKUEN 0x013c
+#define HW_WDTCLKSEL 0x0160
+#define HW_WDTCLKUEN 0x0164
+#define HW_CLKOUTCLKSEL 0x0170
+#define HW_CLKOUTCLKUEN 0x0174
+#define HW_CPUCLKDIV 0x017c
+#define HW_SYSAHBCLKDIV 0x0180
+#define HW_I2S0MCLKDIV 0x0190
+#define HW_I2S0SCLKDIV 0x0194
+#define HW_I2S1MCLKDIV 0x0188
+#define HW_I2S1SCLKDIV 0x018c
+#define HW_UART0CLKDIV 0x0198
+#define HW_UART1CLKDIV 0x019c
+#define HW_UART2CLKDIV 0x01a0
+#define HW_UART3CLKDIV 0x01a4
+#define HW_UART4CLKDIV 0x01a8
+#define HW_UART5CLKDIV 0x01ac
+#define HW_UART6CLKDIV 0x01b0
+#define HW_UART7CLKDIV 0x01b4
+#define HW_UART8CLKDIV 0x01b8
+#define HW_UART9CLKDIV 0x01bc
+#define HW_SPI0CLKDIV 0x01c0
+#define HW_SPI1CLKDIV 0x01c4
+#define HW_QUADSPICLKDIV 0x01c8
+#define HW_SSP0CLKDIV 0x01d0
+#define HW_NANDCLKDIV 0x01d4
+#define HW_TRACECLKDIV 0x01e0
+#define HW_CAMMCLKDIV 0x01e8
+#define HW_WDTCLKDIV 0x01ec
+#define HW_CLKOUTCLKDIV 0x01f4
+#define HW_MACCLKDIV 0x01f8
+#define HW_LCDCLKDIV 0x01fc
+#define HW_ADCANACLKDIV 0x0200
+
+static struct clk *clks[MAX_CLKS];
+static struct clk_onecell_data clk_data;
+static DEFINE_SPINLOCK(asm9260_clk_lock);
+
+struct asm9260_div_clk {
+ unsigned int idx;
+ const char *name;
+ const char *parent_name;
+ u32 reg;
+};
+
+struct asm9260_gate_data {
+ unsigned int idx;
+ const char *name;
+ const char *parent_name;
+ u32 reg;
+ u8 bit_idx;
+ unsigned long flags;
+};
+
+struct asm9260_mux_clock {
+ u8 mask;
+ u32 *table;
+ const char *name;
+ const char **parent_names;
+ u8 num_parents;
+ unsigned long offset;
+ unsigned long flags;
+};
+
+static void __iomem *base;
+
+enum {
+ REFCLK, SYSPLL, I2S0_MCLK, I2S1_MCLK, RTC_OSC, USB_PLL,
+};
+
+static const char *clk_names[] = {
+ [REFCLK] = "oscillator",
+ [SYSPLL] = "pll",
+ [I2S0_MCLK] = "i2s0_mclk",
+ [I2S1_MCLK] = "i2s1_mclk",
+ [RTC_OSC] = "rtc_osc",
+ [USB_PLL] = "usb_pll",
+};
+
+static const struct asm9260_div_clk asm9260_div_clks[] __initconst = {
+ { CLKID_SYS_CPU, "cpu_div", "main_gate", HW_CPUCLKDIV },
+ { CLKID_SYS_AHB, "ahb_div", "cpu_div", HW_SYSAHBCLKDIV },
+
+ /* i2s has two deviders: one for only external mclk and internal
+ * devider for all clks. */
+ { CLKID_SYS_I2S0M, "i2s0m_div", "i2s0_mclk", HW_I2S0MCLKDIV },
+ { CLKID_SYS_I2S1M, "i2s1m_div", "i2s1_mclk", HW_I2S1MCLKDIV },
+ { CLKID_SYS_I2S0S, "i2s0s_div", "i2s0_gate", HW_I2S0SCLKDIV },
+ { CLKID_SYS_I2S1S, "i2s1s_div", "i2s0_gate", HW_I2S1SCLKDIV },
+
+ { CLKID_SYS_UART0, "uart0_div", "uart_gate", HW_UART0CLKDIV },
+ { CLKID_SYS_UART1, "uart1_div", "uart_gate", HW_UART1CLKDIV },
+ { CLKID_SYS_UART2, "uart2_div", "uart_gate", HW_UART2CLKDIV },
+ { CLKID_SYS_UART3, "uart3_div", "uart_gate", HW_UART3CLKDIV },
+ { CLKID_SYS_UART4, "uart4_div", "uart_gate", HW_UART4CLKDIV },
+ { CLKID_SYS_UART5, "uart5_div", "uart_gate", HW_UART5CLKDIV },
+ { CLKID_SYS_UART6, "uart6_div", "uart_gate", HW_UART6CLKDIV },
+ { CLKID_SYS_UART7, "uart7_div", "uart_gate", HW_UART7CLKDIV },
+ { CLKID_SYS_UART8, "uart8_div", "uart_gate", HW_UART8CLKDIV },
+ { CLKID_SYS_UART9, "uart9_div", "uart_gate", HW_UART9CLKDIV },
+};
+
+static const struct asm9260_gate_data asm9260_mux_gates[] __initconst = {
+ { 0, "main_gate", "main_mux", HW_MAINCLKUEN, 0 },
+ { 0, "uart_gate", "uart_mux", HW_UARTCLKUEN, 0 },
+ { 0, "i2s0_gate", "i2s0_mux", HW_I2S0CLKUEN, 0 },
+ { 0, "i2s1_gate", "i2s1_mux", HW_I2S1CLKUEN, 0 },
+ { 0, "wdt_gate", "wdt_mux", HW_WDTCLKUEN, 0 },
+ { 0, "clkout_gate", "clkout_mux", HW_CLKOUTCLKUEN, 0 },
+};
+static const struct asm9260_gate_data asm9260_ahb_gates[] __initconst = {
+ /* ahb gates */
+ { CLKID_AHB_ROM, "rom", "ahb_div",
+ HW_AHBCLKCTRL0, 1, CLK_IGNORE_UNUSED},
+ { CLKID_AHB_RAM, "ram", "ahb_div",
+ HW_AHBCLKCTRL0, 2, CLK_IGNORE_UNUSED},
+ { CLKID_AHB_GPIO, "gpio", "ahb_div",
+ HW_AHBCLKCTRL0, 4 },
+ { CLKID_AHB_MAC, "mac", "ahb_div",
+ HW_AHBCLKCTRL0, 5 },
+ { CLKID_AHB_EMI, "emi", "ahb_div",
+ HW_AHBCLKCTRL0, 6, CLK_IGNORE_UNUSED},
+ { CLKID_AHB_USB0, "usb0", "ahb_div",
+ HW_AHBCLKCTRL0, 7 },
+ { CLKID_AHB_USB1, "usb1", "ahb_div",
+ HW_AHBCLKCTRL0, 8 },
+ { CLKID_AHB_DMA0, "dma0", "ahb_div",
+ HW_AHBCLKCTRL0, 9 },
+ { CLKID_AHB_DMA1, "dma1", "ahb_div",
+ HW_AHBCLKCTRL0, 10 },
+ { CLKID_AHB_UART0, "uart0", "ahb_div",
+ HW_AHBCLKCTRL0, 11 },
+ { CLKID_AHB_UART1, "uart1", "ahb_div",
+ HW_AHBCLKCTRL0, 12 },
+ { CLKID_AHB_UART2, "uart2", "ahb_div",
+ HW_AHBCLKCTRL0, 13 },
+ { CLKID_AHB_UART3, "uart3", "ahb_div",
+ HW_AHBCLKCTRL0, 14 },
+ { CLKID_AHB_UART4, "uart4", "ahb_div",
+ HW_AHBCLKCTRL0, 15 },
+ { CLKID_AHB_UART5, "uart5", "ahb_div",
+ HW_AHBCLKCTRL0, 16 },
+ { CLKID_AHB_UART6, "uart6", "ahb_div",
+ HW_AHBCLKCTRL0, 17 },
+ { CLKID_AHB_UART7, "uart7", "ahb_div",
+ HW_AHBCLKCTRL0, 18 },
+ { CLKID_AHB_UART8, "uart8", "ahb_div",
+ HW_AHBCLKCTRL0, 19 },
+ { CLKID_AHB_UART9, "uart9", "ahb_div",
+ HW_AHBCLKCTRL0, 20 },
+ { CLKID_AHB_I2S0, "i2s0", "ahb_div",
+ HW_AHBCLKCTRL0, 21 },
+ { CLKID_AHB_I2C0, "i2c0", "ahb_div",
+ HW_AHBCLKCTRL0, 22 },
+ { CLKID_AHB_I2C1, "i2c1", "ahb_div",
+ HW_AHBCLKCTRL0, 23 },
+ { CLKID_AHB_SSP0, "ssp0", "ahb_div",
+ HW_AHBCLKCTRL0, 24 },
+ { CLKID_AHB_IOCONFIG, "ioconf", "ahb_div",
+ HW_AHBCLKCTRL0, 25 },
+ { CLKID_AHB_WDT, "wdt", "ahb_div",
+ HW_AHBCLKCTRL0, 26 },
+ { CLKID_AHB_CAN0, "can0", "ahb_div",
+ HW_AHBCLKCTRL0, 27 },
+ { CLKID_AHB_CAN1, "can1", "ahb_div",
+ HW_AHBCLKCTRL0, 28 },
+ { CLKID_AHB_MPWM, "mpwm", "ahb_div",
+ HW_AHBCLKCTRL0, 29 },
+ { CLKID_AHB_SPI0, "spi0", "ahb_div",
+ HW_AHBCLKCTRL0, 30 },
+ { CLKID_AHB_SPI1, "spi1", "ahb_div",
+ HW_AHBCLKCTRL0, 31 },
+
+ { CLKID_AHB_QEI, "qei", "ahb_div",
+ HW_AHBCLKCTRL1, 0 },
+ { CLKID_AHB_QUADSPI0, "quadspi0", "ahb_div",
+ HW_AHBCLKCTRL1, 1 },
+ { CLKID_AHB_CAMIF, "capmif", "ahb_div",
+ HW_AHBCLKCTRL1, 2 },
+ { CLKID_AHB_LCDIF, "lcdif", "ahb_div",
+ HW_AHBCLKCTRL1, 3 },
+ { CLKID_AHB_TIMER0, "timer0", "ahb_div",
+ HW_AHBCLKCTRL1, 4 },
+ { CLKID_AHB_TIMER1, "timer1", "ahb_div",
+ HW_AHBCLKCTRL1, 5 },
+ { CLKID_AHB_TIMER2, "timer2", "ahb_div",
+ HW_AHBCLKCTRL1, 6 },
+ { CLKID_AHB_TIMER3, "timer3", "ahb_div",
+ HW_AHBCLKCTRL1, 7 },
+ { CLKID_AHB_IRQ, "irq", "ahb_div",
+ HW_AHBCLKCTRL1, 8, CLK_IGNORE_UNUSED},
+ { CLKID_AHB_RTC, "rtc", "ahb_div",
+ HW_AHBCLKCTRL1, 9 },
+ { CLKID_AHB_NAND, "nand", "ahb_div",
+ HW_AHBCLKCTRL1, 10 },
+ { CLKID_AHB_ADC0, "adc0", "ahb_div",
+ HW_AHBCLKCTRL1, 11 },
+ { CLKID_AHB_LED, "led", "ahb_div",
+ HW_AHBCLKCTRL1, 12 },
+ { CLKID_AHB_DAC0, "dac0", "ahb_div",
+ HW_AHBCLKCTRL1, 13 },
+ { CLKID_AHB_LCD, "lcd", "ahb_div",
+ HW_AHBCLKCTRL1, 14 },
+ { CLKID_AHB_I2S1, "i2s1", "ahb_div",
+ HW_AHBCLKCTRL1, 15 },
+ { CLKID_AHB_MAC1, "mac1", "ahb_div",
+ HW_AHBCLKCTRL1, 16 },
+};
+
+static const char __initdata *main_mux_p[] = {"oscillator", "pll"};
+static const char __initdata *i2s0_mux_p[] = {"oscillator", "pll", "i2s0m_div"};
+static const char __initdata *i2s1_mux_p[] = {"oscillator", "pll", "i2s1m_div"};
+static const char __initdata *clkout_mux_p[] = {"oscillator", "pll", "rtc"};
+static u32 three_mux_table[] = {0, 1, 3};
+
+static struct asm9260_mux_clock asm9260_mux_clks[] __initdata = {
+ { 1, three_mux_table, "main_mux", main_mux_p,
+ ARRAY_SIZE(main_mux_p), HW_MAINCLKSEL, },
+ { 1, three_mux_table, "uart_mux", main_mux_p,
+ ARRAY_SIZE(main_mux_p), HW_UARTCLKSEL, },
+ { 1, three_mux_table, "wdt_mux", main_mux_p,
+ ARRAY_SIZE(main_mux_p), HW_WDTCLKSEL, },
+ { 3, three_mux_table, "i2s0_mux", i2s0_mux_p,
+ ARRAY_SIZE(i2s0_mux_p), HW_I2S0CLKSEL, },
+ { 3, three_mux_table, "i2s1_mux", i2s1_mux_p,
+ ARRAY_SIZE(i2s1_mux_p), HW_I2S1CLKSEL, },
+ { 3, three_mux_table, "clkout_mux", clkout_mux_p,
+ ARRAY_SIZE(clkout_mux_p), HW_CLKOUTCLKSEL, },
+};
+
+static void __init asm9260_acc_init(struct device_node *np)
+{
+ struct clk *clk;
+ struct resource res;
+ u32 rate;
+ int n;
+ u32 accuracy = 0;
+
+ of_address_to_resource(np, 0, &res);
+ if (!request_mem_region(res.start, resource_size(&res), np->name))
+ panic("%s: unable to request mem region", np->name);
+
+ base = ioremap_nocache(res.start, resource_size(&res));
+ if (!base)
+ panic("%s: unable to map resource", np->name);
+
+
+ /* register pll */
+ rate = (ioread32(base + HW_SYSPLLCTRL) & 0xffff) * 1000000;
+
+ clk_names[REFCLK] = of_clk_get_parent_name(np, 0);
+ accuracy = clk_get_accuracy(__clk_lookup(clk_names[REFCLK]));
+ clk = clk_register_fixed_rate_with_accuracy(NULL, clk_names[SYSPLL],
+ clk_names[REFCLK], 0, rate, accuracy);
+
+ if (IS_ERR(clk))
+ panic("%s: can't register REFCLK. Check DT!", np->name);
+
+ for (n = 0; n < ARRAY_SIZE(asm9260_mux_clks); n++) {
+ const struct asm9260_mux_clock *mc = &asm9260_mux_clks[n];
+
+ mc->parent_names[0] = clk_names[REFCLK];
+ clk = clk_register_mux_table(NULL, mc->name, mc->parent_names,
+ mc->num_parents, mc->flags, base + mc->offset,
+ 0, mc->mask, 0, mc->table, &asm9260_clk_lock);
+ }
+
+ /* clock mux gate cells */
+ for (n = 0; n < ARRAY_SIZE(asm9260_mux_gates); n++) {
+ const struct asm9260_gate_data *gd = &asm9260_mux_gates[n];
+
+ clk = clk_register_gate(NULL, gd->name,
+ gd->parent_name, gd->flags | CLK_SET_RATE_PARENT,
+ base + gd->reg, gd->bit_idx, 0, &asm9260_clk_lock);
+ }
+
+ /* clock div cells */
+ for (n = 0; n < ARRAY_SIZE(asm9260_div_clks); n++) {
+ const struct asm9260_div_clk *dc = &asm9260_div_clks[n];
+
+ clks[dc->idx] = clk_register_divider(NULL, dc->name,
+ dc->parent_name, CLK_SET_RATE_PARENT,
+ base + dc->reg, 0, 8, CLK_DIVIDER_ONE_BASED,
+ &asm9260_clk_lock);
+ }
+
+ /* clock ahb gate cells */
+ for (n = 0; n < ARRAY_SIZE(asm9260_ahb_gates); n++) {
+ const struct asm9260_gate_data *gd = &asm9260_ahb_gates[n];
+
+ clks[gd->idx] = clk_register_gate(NULL, gd->name,
+ gd->parent_name, gd->flags, base + gd->reg,
+ gd->bit_idx, 0, &asm9260_clk_lock);
+ }
+
+ /* check for errors on leaf clocks */
+ for (n = 0; n < MAX_CLKS; n++) {
+ if (!IS_ERR(clks[n]))
+ continue;
+
+ pr_err("%s: Unable to register leaf clock %d\n",
+ np->full_name, n);
+ goto fail;
+ }
+
+ /* register clk-provider */
+ clk_data.clks = clks;
+ clk_data.clk_num = MAX_CLKS;
+ of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
+ return;
+fail:
+ iounmap(base);
+}
+CLK_OF_DECLARE(asm9260_acc, "alphascale,asm9260-clock-controller",
+ asm9260_acc_init);
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 06/10] clocksource: add asm9260_timer driver
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (4 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 05/10] ARM: clk: add clk-asm9260 driver Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 07/10] tty/serial/mxs-auart.c: add initial Alphascale ASM9260 support Oleksij Rempel
` (3 subsequent siblings)
9 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
In some cases asm9260 looks similar to iMX2x. One of exceptions is
timer controller. So this patch introduces new driver for this special case.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
drivers/clocksource/Kconfig | 4 +
drivers/clocksource/Makefile | 1 +
drivers/clocksource/asm9260_timer.c | 234 ++++++++++++++++++++++++++++++++++++
3 files changed, 239 insertions(+)
create mode 100644 drivers/clocksource/asm9260_timer.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index cfd6519..6a03d34 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -216,4 +216,8 @@ config CLKSRC_VERSATILE
ARM Versatile, RealView and Versatile Express reference
platforms.
+config ASM9260_TIMER
+ select CLKSRC_MMIO
+ bool
+
endmenu
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 7fd9fd1..fc93854 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -44,3 +44,4 @@ obj-$(CONFIG_CLKSRC_METAG_GENERIC) += metag_generic.o
obj-$(CONFIG_ARCH_HAS_TICK_BROADCAST) += dummy_timer.o
obj-$(CONFIG_ARCH_KEYSTONE) += timer-keystone.o
obj-$(CONFIG_CLKSRC_VERSATILE) += versatile.o
+obj-$(CONFIG_ASM9260_TIMER) += asm9260_timer.o
diff --git a/drivers/clocksource/asm9260_timer.c b/drivers/clocksource/asm9260_timer.c
new file mode 100644
index 0000000..1b16e00
--- /dev/null
+++ b/drivers/clocksource/asm9260_timer.c
@@ -0,0 +1,234 @@
+/*
+ * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/clk.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/bitops.h>
+
+
+/*
+ * this device provide 4 offsets for each register:
+ * 0x0 - plain read write mode
+ * 0x4 - set mode, OR logic.
+ * 0x8 - clr mode, XOR logic.
+ * 0xc - togle mode.
+ */
+#define SET_REG 4
+#define CLR_REG 8
+
+#define HW_IR 0x0000 /* RW. Interrupt */
+#define BM_IR_CR0 BIT(4)
+#define BM_IR_MR3 BIT(3)
+#define BM_IR_MR2 BIT(2)
+#define BM_IR_MR1 BIT(1)
+#define BM_IR_MR0 BIT(0)
+
+#define HW_TCR 0x0010 /* RW. Timer controller */
+/* BM_C*_RST
+ * Timer Counter and the Prescale Counter are synchronously reset on the
+ * next positive edge of PCLK. The counters remain reset until TCR[1] is
+ * returned to zero. */
+#define BM_C3_RST BIT(7)
+#define BM_C2_RST BIT(6)
+#define BM_C1_RST BIT(5)
+#define BM_C0_RST BIT(4)
+/* BM_C*_EN
+ * 1 - Timer Counter and Prescale Counter are enabled for counting
+ * 0 - counters are disabled */
+#define BM_C3_EN BIT(3)
+#define BM_C2_EN BIT(2)
+#define BM_C1_EN BIT(1)
+#define BM_C0_EN BIT(0)
+
+#define HW_DIR 0x0020 /* RW. Direction? */
+/* 00 - count up
+ * 01 - count down
+ * 10 - ?? 2^n/2 */
+#define BM_DIR0_SHIFT 0
+#define BM_DIR1_SHIFT 4
+#define BM_DIR2_SHIFT 8
+#define BM_DIR3_SHIFT 12
+
+#define HW_TC0 0x0030 /* RO. Timer counter 0 */
+/* HW_TC*. Timer counter owerflow (0xffff.ffff to 0x0000.0000) do not generate
+ * interrupt. This registers can be used to detect overflow */
+#define HW_TC1 0x0040
+#define HW_TC2 0x0050
+#define HW_TC3 0x0060
+
+#define HW_PR 0x0070 /* RW. prescaler */
+#define HW_PC 0x0080 /* RO. Prescaler counter */
+#define HW_MCR 0x0090 /* RW. Match control */
+/* enable interrupt on match */
+#define BM_MCR_INT_EN(n) (1 << (n * 3 + 0))
+/* enable TC reset on match */
+#define BM_MCR_RES_EN(n) (1 << (n * 3 + 1))
+/* enable stop TC on match */
+#define BM_MCR_STOP_EN(n) (1 << (n * 3 + 2))
+
+#define HW_MR0 0x00a0 /* RW. Match reg */
+#define HW_MR1 0x00b0
+#define HW_MR2 0x00C0
+#define HW_MR3 0x00D0
+#define HW_CCR 0x00E0 /* RW. Capture control */
+#define HW_CR0 0x00F0 /* RO. Capture reg */
+#define HW_CR1 0x0100
+#define HW_CR2 0x0110
+#define HW_CR3 0x0120
+#define HW_EMR 0x0130 /* RW. External Match */
+#define HW_PWMTH0 0x0140 /* RW. PWM width */
+#define HW_PWMTH1 0x0150
+#define HW_PWMTH2 0x0160
+#define HW_PWMTH3 0x0170
+#define HW_CTCR 0x0180 /* Counter control */
+#define HW_PWMC 0x0190 /* PWM control */
+
+static void __iomem *base;
+static unsigned long ticks_per_jiffy;
+
+static int asm9260_timer_set_next_event(unsigned long delta,
+ struct clock_event_device *dev)
+{
+ /* configure match count for TC0 */
+ writel_relaxed(delta, base + HW_MR0);
+ /* enable TC0 */
+ writel_relaxed(BM_C0_EN, base + HW_TCR + SET_REG);
+ return 0;
+}
+
+static void asm9260_timer_set_mode(enum clock_event_mode mode,
+ struct clock_event_device *evt)
+{
+ /* stop timer0 */
+ writel_relaxed(BM_C0_EN, base + HW_TCR + CLR_REG);
+
+ switch (mode) {
+ case CLOCK_EVT_MODE_PERIODIC:
+ /* disable reset and stop on match */
+ writel_relaxed(BM_MCR_RES_EN(0) | BM_MCR_STOP_EN(0),
+ base + HW_MCR + CLR_REG);
+ /* configure match count for TC0 */
+ writel_relaxed(ticks_per_jiffy, base + HW_MR0);
+ /* enable TC0 */
+ writel_relaxed(BM_C0_EN, base + HW_TCR + SET_REG);
+ break;
+ case CLOCK_EVT_MODE_ONESHOT:
+ /* enable reset and stop on match */
+ writel_relaxed(BM_MCR_RES_EN(0) | BM_MCR_STOP_EN(0),
+ base + HW_MCR + SET_REG);
+ break;
+ default:
+ break;
+ }
+}
+
+static struct clock_event_device asm9260_clockevent_device = {
+ .name = "asm9260-clockevent-dev",
+ .rating = 200,
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .set_next_event = asm9260_timer_set_next_event,
+ .set_mode = asm9260_timer_set_mode,
+};
+
+static irqreturn_t asm9260_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = &asm9260_clockevent_device;
+
+ evt->event_handler(evt);
+
+ writel_relaxed(BM_IR_MR0, base + HW_IR);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction asm9260_timer_irq = {
+ .name = "asm9260-clockevent-dev",
+ .flags = IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = asm9260_timer_interrupt,
+};
+
+/*
+ * ---------------------------------------------------------------------------
+ * Timer initialization
+ * ---------------------------------------------------------------------------
+ */
+
+static void __init asm9260_clockevent_init(struct clk *clk)
+{
+ unsigned long rate = clk_get_rate(clk);
+
+ ticks_per_jiffy = DIV_ROUND_CLOSEST(rate, HZ);
+ asm9260_clockevent_device.cpumask = cpumask_of(0);
+ clockevents_config_and_register(&asm9260_clockevent_device,
+ rate, 0x2c00, 0xfffffffe);
+}
+
+static void __init asm9260_clocksource_init(struct clk *clk)
+{
+ unsigned long hz = clk_get_rate(clk);
+
+ clocksource_mmio_init(base + HW_TC1,
+ "asm9260-clocksource", hz,
+ 200, 32, clocksource_mmio_readl_up);
+
+ /* Seems like we can't use counter without match register even if
+ * actions for MR are disabled. */
+ writel_relaxed(0xffffffff, base + HW_MR1);
+ /* enable TC1 */
+ writel_relaxed(BM_C1_EN, base + HW_TCR + SET_REG);
+}
+
+static void __init asm9260_timer_init(struct device_node *np)
+{
+ int irq;
+ struct clk *clk;
+ struct resource res;
+ int ret;
+
+ of_address_to_resource(np, 0, &res);
+ if (!request_mem_region(res.start, resource_size(&res),
+ "asm9260-timer"))
+ panic("%s: unable to request mem region", np->name);
+
+ base = ioremap_nocache(res.start, resource_size(&res));
+ if (!base)
+ panic("%s: unable to map resource", np->name);
+
+ clk = of_clk_get(np, 0);
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ panic("Failed to enable clk!\n");
+
+ irq = irq_of_parse_and_map(np, 0);
+ setup_irq(irq, &asm9260_timer_irq);
+
+ /* set all timers for count-up */
+ writel_relaxed(0, base + HW_DIR);
+ /* disable divider */
+ writel_relaxed(0, base + HW_PR);
+ /* make sure all timers use every rising PCLK edge. */
+ writel_relaxed(0, base + HW_CTCR);
+ /* enable interrupt for TC0 and clean setting for all other lines */
+ writel_relaxed(BM_MCR_INT_EN(0) , base + HW_MCR);
+
+ asm9260_clocksource_init(clk);
+ asm9260_clockevent_init(clk);
+}
+CLOCKSOURCE_OF_DECLARE(asm9260_timer, "alphascale,asm9260-timer",
+ asm9260_timer_init);
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 07/10] tty/serial/mxs-auart.c: add initial Alphascale ASM9260 support
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (5 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 06/10] clocksource: add asm9260_timer driver Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 08/10] add Alphascale to vendor-prefixes.txt Oleksij Rempel
` (2 subsequent siblings)
9 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
Alphascale ASM9260 uart IP has some common registers with
Freescale STMP37XX. This patch provide initial changes which
allow to reuse mxs-auart.c code for ASM9260.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
drivers/tty/serial/Kconfig | 5 +-
drivers/tty/serial/alphascale,asm9260_serial.h | 373 +++++++++++++++++++++++++
drivers/tty/serial/mxs-auart.c | 344 +++++++++++++++--------
3 files changed, 599 insertions(+), 123 deletions(-)
create mode 100644 drivers/tty/serial/alphascale,asm9260_serial.h
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 26cec64..11bbb76 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1385,11 +1385,12 @@ config SERIAL_MSM_SMD
ports via tty device interface for MSM chipset.
config SERIAL_MXS_AUART
- depends on ARCH_MXS
+ depends on ARCH_MXS || MACH_ASM9260
tristate "MXS AUART support"
select SERIAL_CORE
help
- This driver supports the MXS Application UART (AUART) port.
+ This driver supports the MXS and Alphascale ASM9260 Application
+ UART (AUART) port.
config SERIAL_MXS_AUART_CONSOLE
bool "MXS AUART console support"
diff --git a/drivers/tty/serial/alphascale,asm9260_serial.h b/drivers/tty/serial/alphascale,asm9260_serial.h
new file mode 100644
index 0000000..eeed9c4
--- /dev/null
+++ b/drivers/tty/serial/alphascale,asm9260_serial.h
@@ -0,0 +1,373 @@
+/*
+ * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _ALPHASCALE_ASM9260_SERIAL_H
+#define _ALPHASCALE_ASM9260_SERIAL_H
+
+/* RX ctrl register */
+#define ASM9260_HW_CTRL0 0x0000
+/* RW. Set to zero for normal operation. */
+#define ASM9260_BM_CTRL0_SFTRST BIT(31)
+/*
+ * RW. 0 for normal operation; 1 gates all of the block level clocks off for
+ * miniminizing AC energy consumption.
+ */
+#define ASM9260_BM_CTRL0_CLKGATE BIT(30)
+/*
+ * RW. Tell the UART to execute the RX DMA Command. The
+ * UART will clear this bit at the end of receive execution.
+ */
+#define ASM9260_BM_CTRL0_RXDMA_RUN BIT(28)
+/* RW. 0 use FIFO for status register; 1 use DMA */
+#define ASM9260_BM_CTRL0_RXTO_SOURCE_STATUS BIT(25)
+/*
+ * RW. RX TIMEOUT Enable. Valid for FIFO and DMA.
+ * Warning: If this bit is set to 0, the RX timeout will not affect receive DMA
+ * operation. If this bit is set to 1, a receive timeout will cause the receive
+ * DMA logic to terminate by filling the remaining DMA bytes with garbage data.
+ */
+#define ASM9260_BM_CTRL0_RXTO_ENABLE BIT(24)
+/*
+ * RW. Receive Timeout Counter Value: number of 8-bit-time to wait before
+ * asserting timeout on the RX input. If the RXFIFO is not empty and the RX
+ * input is idle, then the watchdog counter will decrement each bit-time. Note
+ * 7-bit-time is added to the programmed value, so a value of zero will set
+ * the counter to 7-bit-time, a value of 0x1 gives 15-bit-time and so on. Also
+ * note that the counter is reloaded at the end of each frame, so if the frame
+ * is 10 bits long and the timeout counter value is zero, then timeout will
+ * occur (when FIFO is not empty) even if the RX input is not idle. The default
+ * value is 0x3 (31 bit-time).
+ */
+#define ASM9260_BM_CTRL0_RXTO_MASK (0xff<<16)
+/* TIMEOUT = (100*7+1)*(1/BAUD) */
+#define ASM9260_BM_CTRL0_DEFAULT_RXTIMEOUT (20<<16)
+/* RW. Number of bytes to receive. This must be a multiple of 4 */
+#define ASM9260_BM_CTRL0_RXDMA_COUNT_MASK (0xffff<<0)
+
+/* TX ctrl register */
+#define ASM9260_HW_CTRL1 0x0010
+/*
+ * RW. Tell the UART to execute the TX DMA Command. The
+ * UART will clear this bit at the end of transmit execution.
+ */
+#define ASM9260_BM_CTRL1_TXDMA_RUN BIT(28)
+/* RW. Number of bytes to transmit. */
+#define ASM9260_BM_CTRL1_TXDMA_COUNT_MASK (0xffff << 0)
+
+#define ASM9260_HW_CTRL2 0x0020
+/*
+ * RW. Receive dma will terminate on error. (Cmd_end signal may not be asserted
+ * when this occurs.)
+ */
+#define ASM9260_BM_CTRL2_DMAONERROR BIT(26)
+/*
+ * RW. Transmit DMA Enable. Data Register can be loaded with up to 4 bytes per
+ * write. TXFIFO must be enabled in TXDMA mode.
+ */
+#define ASM9260_BM_CTRL2_TXDMAE BIT(25)
+/*
+ * RW. Receive DMA Enable. Data Register can be contain up to 4 bytes per read.
+ * RXFIFO must be enabled in RXDMA mode.
+ */
+#define ASM9260_BM_CTRL2_RXDMAE BIT(24)
+/*
+ * RW. Receive Interrupt FIFO Level Select.
+ * The trigger points for the receive interrupt are as follows:
+ * ONE_EIGHTHS = 0x0 Trigger on FIFO full to at least 2 of 16 entries.
+ * ONE_QUARTER = 0x1 Trigger on FIFO full to at least 4 of 16 entries.
+ * ONE_HALF = 0x2 Trigger on FIFO full to at least 8 of 16 entries.
+ * THREE_QUARTERS = 0x3 Trigger on FIFO full to at least 12 of 16 entries.
+ * SEVEN_EIGHTHS = 0x4 Trigger on FIFO full to at least 14 of 16 entries.
+ */
+#define ASM9260_BM_CTRL2_RXIFLSEL (7<<20)
+#define ASM9260_BM_CTRL2_DEFAULT_RXIFLSEL (3<<20)
+/* RW. Same as RXIFLSEL */
+#define ASM9260_BM_CTRL2_TXIFLSEL (7<<16)
+#define ASM9260_BM_CTRL2_DEFAULT_TXIFLSEL (2<<16)
+/* RW. CTS Enable */
+#define ASM9260_BM_CTRL2_CTSE BIT(15)
+/* RW. RTS Enable */
+#define ASM9260_BM_CTRL2_RTSE BIT(14)
+/*
+ * RW. Manually trigger RTS. Works only if ASM9260_BM_CTRL2_RTSE = 0.
+ * When this bit is 1, the output is 0.
+ */
+#define ASM9260_BM_CTRL2_RTS BIT(11)
+/* RW. Set DTR. When this bit is 1, the output is 0. */
+#define ASM9260_BM_CTRL2_DTR BIT(10)
+/* RW. RX Enable */
+#define ASM9260_BM_CTRL2_RXE BIT(9)
+/* RW. TX Enable */
+#define ASM9260_BM_CTRL2_TXE BIT(8)
+/* RW. Loop Back Enable */
+#define ASM9260_BM_CTRL2_LBE BIT(7)
+#define ASM9260_BM_CTRL2_PORT_ENABLE BIT(0)
+
+#define ASM9260_HW_LINECTRL 0x0030
+#define ASM9260_BM_LCTRL_BAUD_DIVINT (0xFFFF<<16)
+#define ASM9260_BM_LCTRL_BAUD_DIVFRA (0x3F<<8)
+/*
+ * RW. Stick Parity Select. When bits 1, 2, and 7 of this register are set, the
+ * parity bit is transmitted and checked as a 0. When bits 1 and 7 are set,
+ * and bit 2 is 0, the parity bit is transmitted and checked as a 1. When this
+ * bit is cleared stick parity is disabled.
+ */
+#define ASM9260_BM_LCTRL_SPS BIT(7)
+/* RW. Word length */
+#define ASM9260_BM_LCTRL_WLEN (3<<5)
+#define ASM9260_BM_LCTRL_CHRL_5 (0<<5)
+#define ASM9260_BM_LCTRL_CHRL_6 (1<<5)
+#define ASM9260_BM_LCTRL_CHRL_7 (2<<5)
+#define ASM9260_BM_LCTRL_CHRL_8 (3<<5)
+/*
+ * RW. Enable FIFOs. If this bit is set to 1, transmit and receive FIFO buffers
+ * are enabled (FIFO mode). When cleared to 0, the FIFOs are disabled (character
+ * mode); that is, the FIFOs become 1-byte-deep holding registers.
+ */
+#define ASM9260_BM_LCTRL_FEN BIT(4)
+/*
+ * RW. Two Stop Bits Select. If this bit is set to 1, two stop bits are
+ * transmitted at the end of the frame. The receive logic does not check for
+ * two stop bits being received.
+ */
+#define ASM9260_BM_LCTRL_STP2 BIT(3)
+#define ASM9260_BM_LCTRL_NBSTOP_1 (0<<3)
+#define ASM9260_BM_LCTRL_NBSTOP_2 (1<<3)
+/* RW. Even Parity Select. If disabled, then odd parity is performed. */
+#define ASM9260_BM_LCTRL_EPS BIT(2)
+/* Parity Enable. */
+#define ASM9260_BM_LCTRL_PEN BIT(1)
+#define ASM9260_BM_LCTRL_PAR_MARK ((3<<1) | (1<<7))
+#define ASM9260_BM_LCTRL_PAR_SPACE ((1<<1) | (1<<7))
+#define ASM9260_BM_LCTRL_PAR_ODD ((1<<1) | (0<<7))
+#define ASM9260_BM_LCTRL_PAR_EVEN ((3<<1) | (0<<7))
+#define ASM9260_BM_LCTRL_PAR_NONE (0<<1)
+/*
+ * RW. Send Break. If this bit is set to 1, a low-level is continually output on
+ * the UARTTXD output, after completing transmission of the current character.
+ * For the proper execution of the break command, the software must set this bit
+ * for@least two complete frames. For normal use, this bit must be cleared
+ * to 0.
+ */
+#define ASM9260_BM_LCTRL_BREAK BIT(0)
+
+/*
+ * Interrupt register.
+ * contains the interrupt enables and the interrupt status bits
+ */
+#define ASM9260_HW_INTR 0x0040
+/* Tx FIFO EMPTY Raw Interrupt enable */
+#define ASM9260_BM_INTR_TFEIEN BIT(27)
+/* Overrun Error Interrupt Enable. */
+#define ASM9260_BM_INTR_OEIEN BIT(26)
+/* Break Error Interrupt Enable. */
+#define ASM9260_BM_INTR_BEIEN BIT(25)
+/* Parity Error Interrupt Enable. */
+#define ASM9260_BM_INTR_PEIEN BIT(24)
+/* Framing Error Interrupt Enable. */
+#define ASM9260_BM_INTR_FEIEN BIT(23)
+/*
+ * RW. Receive Timeout Interrupt Enable.
+ * If not set and FIFO is enabled, then RX will be triggered only
+ * if FIFO is full.
+ */
+#define ASM9260_BM_INTR_RTIEN BIT(22)
+/* Transmit Interrupt Enable. */
+#define ASM9260_BM_INTR_TXIEN BIT(21)
+/* Receive Interrupt Enable. */
+#define ASM9260_BM_INTR_RXIEN BIT(20)
+/* nUARTDSR Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_DSRMIEN BIT(19)
+/* nUARTDCD Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_DCDMIEN BIT(18)
+/* nUARTCTS Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_CTSMIEN BIT(17)
+/* nUARTRI Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_RIMIEN BIT(16)
+/* Auto-Boud Timeout */
+#define ASM9260_BM_INTR_ABTO BIT(13)
+#define ASM9260_BM_INTR_ABEO BIT(12)
+/* Tx FIFO EMPTY Raw Interrupt state */
+#define ASM9260_BM_INTR_TFEIS BIT(11)
+/* Overrun Error */
+#define ASM9260_BM_INTR_OEIS BIT(10)
+/* Break Error */
+#define ASM9260_BM_INTR_BEIS BIT(9)
+/* Parity Error */
+#define ASM9260_BM_INTR_PEIS BIT(8)
+/* Framing Error */
+#define ASM9260_BM_INTR_FEIS BIT(7)
+/* Receive Timeout */
+#define ASM9260_BM_INTR_RTIS BIT(6)
+/* Transmit done */
+#define ASM9260_BM_INTR_TXIS BIT(5)
+/* Receive done */
+#define ASM9260_BM_INTR_RXIS BIT(4)
+#define ASM9260_BM_INTR_DSRMIS BIT(3)
+#define ASM9260_BM_INTR_DCDMIS BIT(2)
+#define ASM9260_BM_INTR_CTSMIS BIT(1)
+#define ASM9260_BM_INTR_RIMIS BIT(0)
+#define ASM9260_BM_INTR_DEF_MASK (ASM9260_BM_INTR_RXIEN \
+ | ASM9260_BM_INTR_TXIEN | ASM9260_BM_INTR_RTIEN \
+ | ASM9260_BM_INTR_FEIEN | ASM9260_BM_INTR_PEIEN \
+ | ASM9260_BM_INTR_BEIEN | ASM9260_BM_INTR_OEIEN)
+#define ASM9260_BM_INTR_DEF_IS_MASK (BM_INTR_DEF_MASK >> 16)
+#define ASM9260_BM_INTR_EN_MASK (0x3fff0000)
+#define ASM9260_BM_INTR_IS_MASK (0x00003fff)
+
+/*
+ * RW. In DMA mode, up to 4 Received/Transmit characters can be accessed at a
+ * time. In PIO mode, only one character can be accessed at a time. The status
+ * register contains the receive data flags and valid bits.
+ */
+#define ASM9260_HW_DATA 0x0050
+
+#define ASM9260_HW_STAT 0x0060
+/* RO. If 1, UARTAPP is present in this product. */
+#define ASM9260_BM_STAT_PRESENT BIT(31)
+/* RO. If 1, HISPEED is present in this product. */
+#define ASM9260_BM_STAT_HISPEED BIT(30)
+/* RO. UART Busy. */
+#define ASM9260_BM_STAT_BUSY BIT(29)
+/* RO. Clear To Send. */
+#define ASM9260_BM_STAT_CTS BIT(28)
+/* RO. Transmit FIFO/PIO Empty */
+#define ASM9260_BM_STAT_TXEMPTY BIT(27)
+/* RO. Receive FIFO Full. */
+#define ASM9260_BM_STAT_RXFULL BIT(26)
+/* RO. Transmit FIFO Full. */
+#define ASM9260_BM_STAT_TXFULL BIT(25)
+/* RO. Receive FIFO Empty. */
+#define ASM9260_BM_STAT_RXEMPTY BIT(24)
+/*
+ * RW. The invalid state of the last read of Receive Data. Each
+ * bit corresponds to one byte of the RX data. (1 = invalid.)
+ */
+#define ASM9260_BM_STAT_RXBYTE_INVALID_MASK (0xf<<20)
+/*
+ * RO. Overrun Error. This bit is set to 1 if data is received and the FIFO is
+ * already full. This bit is cleared to 0 by any write to the Status Register.
+ * The FIFO contents remain valid since no further data is written when the
+ * FIFO is full; only the contents of the shift register are overwritten. The
+ * CPU must now read the data in order to empty the FIFO.
+ */
+#define ASM9260_BM_STAT_OVERRUNERR BIT(19)
+/*
+ * RW. Break Error. For PIO mode, this is for the last character read from the
+ * data register. For DMA mode, it will be set to 1 if any received character
+ * for a particular RXDMA command had a Break Error. To clear this bit, write a
+ * zero to it. Note that clearing this bit does not affect the interrupt status,
+ * which must be cleared by writing the interrupt register.
+ */
+#define ASM9260_BM_STAT_BREAKERR BIT(18)
+/* RW. Parity Error. Same as BREAKERR. */
+#define ASM9260_BM_STAT_PARITYERR BIT(17)
+/* RW. Framing Erro. Same as BREAKERR. */
+#define ASM9260_BM_STAT_FRAMEERR BIT(16)
+/* RO. Number of bytes received during a Receive DMA command. */
+#define ASM9260_BM_STAT_RXCOUNT_MASK (0xffff<<0)
+
+/* RO. The UART Debug Register contains the state of the DMA signals. */
+#define ASM9260_HW_DEBUG 0x0070
+/* DMA Command Run Status */
+#define ASM9260_BM_DEBUG_TXDMARUN BIT(5)
+#define ASM9260_BM_DEBUG_RXDMARUN BIT(4)
+/* DMA Command End Status */
+#define ASM9260_BM_DEBUG_TXCMDEND BIT(3)
+#define ASM9260_BM_DEBUG_RXCMDEND BIT(2)
+/* DMA Request Status */
+#define ASM9260_BM_DEBUG_TXDMARQ BIT(1)
+#define ASM9260_BM_DEBUG_RXDMARQ BIT(0)
+
+#define ASM9260_HW_ILPR 0x0080
+
+#define ASM9260_HW_RS485CTRL 0x0090
+/*
+ * RW. This bit reverses the polarity of the direction control signal on the RTS
+ * (or DTR) pin.
+ * If 0, The direction control pin will be driven to logic ?0? when the
+ * transmitter has data to be sent. It will be driven to logic ?1? after the
+ * last bit of data has been transmitted.
+ */
+#define ASM9260_BM_RS485CTRL_ONIV BIT(5)
+/* RW. Enable Auto Direction Control. */
+#define ASM9260_BM_RS485CTRL_DIR_CTRL BIT(4)
+/*
+ * RW. If 0 and DIR_CTRL = 1, pin RTS is used for direction control.
+ * If 1 and DIR_CTRL = 1, pin DTR is used for direction control.
+ */
+#define ASM9260_BM_RS485CTRL_PINSEL BIT(3)
+/* RW. Enable Auto Address Detect (AAD). */
+#define ASM9260_BM_RS485CTRL_AADEN BIT(2)
+/* RW. Disable receiver. */
+#define ASM9260_BM_RS485CTRL_RXDIS BIT(1)
+/* RW. Enable RS-485/EIA-485 Normal Multidrop Mode (NMM) */
+#define ASM9260_BM_RS485CTRL_RS485EN BIT(0)
+
+#define ASM9260_HW_RS485ADRMATCH 0x00a0
+/* Contains the address match value. */
+#define ASM9260_BM_RS485ADRMATCH_MASK (0xff<<0)
+
+#define ASM9260_HW_RS485DLY 0x00b0
+/*
+ * RW. Contains the direction control (RTS or DTR) delay value. This delay time
+ * is in periods of the baud clock.
+ */
+#define ASM9260_BM_RS485DLY_MASK (0xff<<0)
+
+#define ASM9260_HW_AUTOBAUD 0x00c0
+/* WO. Auto-baud time-out interrupt clear bit. */
+#define ASM9260_BM_AUTOBAUD_ABTOIntClr BIT(9)
+/* WO. End of auto-baud interrupt clear bit. */
+#define ASM9260_BM_AUTOBAUD_ABEOIntClr BIT(8)
+/* Restart in case of timeout (counter restarts at next UART Rx falling edge) */
+#define ASM9260_BM_AUTOBAUD_AUTORESTART BIT(2)
+/* Auto-baud mode select bit. 0 - Mode 0, 1 - Mode 1. */
+#define ASM9260_BM_AUTOBAUD_MODE BIT(1)
+/*
+ * Auto-baud start (auto-baud is running). Auto-baud run bit. This bit is
+ * automatically cleared after auto-baud completion.
+ */
+#define ASM9260_BM_AUTOBAUD_START BIT(0)
+
+#define ASM9260_HW_CTRL3 0x00d0
+#define ASM9260_BM_CTRL3_OUTCLK_DIV_MASK (0xffff<<16)
+/*
+ * RW. Provide clk over OUTCLK pin. In case of asm9260 it can be configured on
+ * pins 137 and 144.
+ */
+#define ASM9260_BM_CTRL3_MASTERMODE BIT(6)
+/* RW. Baud Rate Mode: 1 - Enable sync mode. 0 - async mode. */
+#define ASM9260_BM_CTRL3_SYNCMODE BIT(4)
+/* RW. 1 - MSB bit send frist; 0 - LSB bit frist. */
+#define ASM9260_BM_CTRL3_MSBF BIT(2)
+/* RW. 1 - sample rate = 8 x Baudrate; 0 - sample rate = 16 x Baudrate. */
+#define ASM9260_BM_CTRL3_BAUD8 BIT(1)
+/* RW. 1 - Set word lenght to 9bit. 0 - use ASM9260_BM_LCTRL_WLEN */
+#define ASM9260_BM_CTRL3_9BIT BIT(0)
+
+#define ASM9260_HW_ISO7816_CTRL 0x00e0
+/* RW. Enable High Speed mode. */
+#define ASM9260_BM_ISO7816CTRL_HS BIT(12)
+/* Disable Successive Receive NACK */
+#define ASM9260_BM_ISO7816CTRL_DS_NACK BIT(8)
+#define ASM9260_BM_ISO7816CTRL_MAX_ITER_MASK (0xff<<4)
+/* Receive NACK Inhibit */
+#define ASM9260_BM_ISO7816CTRL_INACK BIT(3)
+#define ASM9260_BM_ISO7816CTRL_NEG_DATA BIT(2)
+/* RW. 1 - ISO7816 mode; 0 - USART mode */
+#define ASM9260_BM_ISO7816CTRL_ENABLE BIT(0)
+
+#define ASM9260_HW_ISO7816_ERRCNT 0x00f0
+/* Parity error counter. Will be cleared after reading */
+#define ASM9260_BM_ISO7816_NB_ERRORS_MASK (0xff<<0)
+
+#define ASM9260_HW_ISO7816_STATUS 0x0100
+/* Max number of Repetitions Reached */
+#define ASM9260_BM_ISO7816_STAT_ITERATION BIT(0)
+#endif
diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c
index b5c3292..b5a1455 100644
--- a/drivers/tty/serial/mxs-auart.c
+++ b/drivers/tty/serial/mxs-auart.c
@@ -1,17 +1,18 @@
/*
- * Freescale STMP37XX/STMP378X Application UART driver
+ * Application UART driver for:
+ * Freescale STMP37XX/STMP378X
+ * Alphascale ASM9260
*
* Author: dmitry pervushin <dimka@embeddedalley.com>
*
+ * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de>
+ * Provide Alphascale ASM9260 support.
* Copyright 2008-2010 Freescale Semiconductor, Inc.
* Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/kernel.h>
@@ -37,34 +38,23 @@
#include <linux/dmaengine.h>
#include <asm/cacheflush.h>
+#include "alphascale,asm9260_serial.h"
#define MXS_AUART_PORTS 5
#define MXS_AUART_FIFO_SIZE 16
+#define MXS_DEVICENAME "ttyAPP"
+#define DRIVER_NAME "mxs-auart"
+
+#define SET_REG 0x4
+#define CLR_REG 0x8
+#define TOG_REG 0xc
#define AUART_CTRL0 0x00000000
-#define AUART_CTRL0_SET 0x00000004
-#define AUART_CTRL0_CLR 0x00000008
-#define AUART_CTRL0_TOG 0x0000000c
#define AUART_CTRL1 0x00000010
-#define AUART_CTRL1_SET 0x00000014
-#define AUART_CTRL1_CLR 0x00000018
-#define AUART_CTRL1_TOG 0x0000001c
#define AUART_CTRL2 0x00000020
-#define AUART_CTRL2_SET 0x00000024
-#define AUART_CTRL2_CLR 0x00000028
-#define AUART_CTRL2_TOG 0x0000002c
#define AUART_LINECTRL 0x00000030
-#define AUART_LINECTRL_SET 0x00000034
-#define AUART_LINECTRL_CLR 0x00000038
-#define AUART_LINECTRL_TOG 0x0000003c
#define AUART_LINECTRL2 0x00000040
-#define AUART_LINECTRL2_SET 0x00000044
-#define AUART_LINECTRL2_CLR 0x00000048
-#define AUART_LINECTRL2_TOG 0x0000004c
#define AUART_INTR 0x00000050
-#define AUART_INTR_SET 0x00000054
-#define AUART_INTR_CLR 0x00000058
-#define AUART_INTR_TOG 0x0000005c
#define AUART_DATA 0x00000060
#define AUART_STAT 0x00000070
#define AUART_DEBUG 0x00000080
@@ -129,6 +119,17 @@ static struct uart_driver auart_driver;
enum mxs_auart_type {
IMX23_AUART,
IMX28_AUART,
+ ASM9260_AUART,
+};
+
+struct mxs_auart_regs {
+ void __iomem *ctrl0;
+ void __iomem *ctrl1;
+ void __iomem *ctrl2;
+ void __iomem *linectrl;
+ void __iomem *intr;
+ void __iomem *data;
+ void __iomem *stat;
};
struct mxs_auart_port {
@@ -142,9 +143,11 @@ struct mxs_auart_port {
unsigned int ctrl;
enum mxs_auart_type devtype;
+ struct mxs_auart_regs regs;
unsigned int irq;
struct clk *clk;
+ struct clk *clk_ahb;
struct device *dev;
/* for DMA */
@@ -160,6 +163,7 @@ struct mxs_auart_port {
static struct platform_device_id mxs_auart_devtype[] = {
{ .name = "mxs-auart-imx23", .driver_data = IMX23_AUART },
{ .name = "mxs-auart-imx28", .driver_data = IMX28_AUART },
+ { .name = "as-auart-asm9260", .driver_data = ASM9260_AUART },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(platform, mxs_auart_devtype);
@@ -171,7 +175,11 @@ static struct of_device_id mxs_auart_dt_ids[] = {
}, {
.compatible = "fsl,imx23-auart",
.data = &mxs_auart_devtype[IMX23_AUART]
+ }, {
+ .compatible = "alphascale,asm9260-auart",
+ .data = &mxs_auart_devtype[ASM9260_AUART]
}, { /* sentinel */ }
+
};
MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids);
@@ -180,6 +188,11 @@ static inline int is_imx28_auart(struct mxs_auart_port *s)
return s->devtype == IMX28_AUART;
}
+static inline int is_asm9260_auart(struct mxs_auart_port *s)
+{
+ return s->devtype == ASM9260_AUART;
+}
+
static inline bool auart_dma_enabled(struct mxs_auart_port *s)
{
return s->flags & MXS_AUART_DMA_ENABLED;
@@ -281,19 +294,19 @@ static void mxs_auart_tx_chars(struct mxs_auart_port *s)
}
- while (!(readl(s->port.membase + AUART_STAT) &
+ while (!(readl(s->regs.stat) &
AUART_STAT_TXFF)) {
if (s->port.x_char) {
s->port.icount.tx++;
writel(s->port.x_char,
- s->port.membase + AUART_DATA);
+ s->regs.data);
s->port.x_char = 0;
continue;
}
if (!uart_circ_empty(xmit) && !uart_tx_stopped(&s->port)) {
s->port.icount.tx++;
writel(xmit->buf[xmit->tail],
- s->port.membase + AUART_DATA);
+ s->regs.data);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
} else
break;
@@ -303,10 +316,10 @@ static void mxs_auart_tx_chars(struct mxs_auart_port *s)
if (uart_circ_empty(&(s->port.state->xmit)))
writel(AUART_INTR_TXIEN,
- s->port.membase + AUART_INTR_CLR);
+ s->regs.intr + CLR_REG);
else
writel(AUART_INTR_TXIEN,
- s->port.membase + AUART_INTR_SET);
+ s->regs.intr + SET_REG);
if (uart_tx_stopped(&s->port))
mxs_auart_stop_tx(&s->port);
@@ -318,8 +331,8 @@ static void mxs_auart_rx_char(struct mxs_auart_port *s)
u32 stat;
u8 c;
- c = readl(s->port.membase + AUART_DATA);
- stat = readl(s->port.membase + AUART_STAT);
+ c = readl(s->regs.data);
+ stat = readl(s->regs.stat);
flag = TTY_NORMAL;
s->port.icount.rx++;
@@ -354,7 +367,7 @@ static void mxs_auart_rx_char(struct mxs_auart_port *s)
uart_insert_char(&s->port, stat, AUART_STAT_OERR, c, flag);
out:
- writel(stat, s->port.membase + AUART_STAT);
+ writel(stat, s->regs.stat);
}
static void mxs_auart_rx_chars(struct mxs_auart_port *s)
@@ -362,13 +375,13 @@ static void mxs_auart_rx_chars(struct mxs_auart_port *s)
u32 stat = 0;
for (;;) {
- stat = readl(s->port.membase + AUART_STAT);
+ stat = readl(s->regs.stat);
if (stat & AUART_STAT_RXFE)
break;
mxs_auart_rx_char(s);
}
- writel(stat, s->port.membase + AUART_STAT);
+ writel(stat, s->regs.stat);
tty_flip_buffer_push(&s->port.state->port);
}
@@ -404,7 +417,7 @@ static void mxs_auart_set_mctrl(struct uart_port *u, unsigned mctrl)
{
struct mxs_auart_port *s = to_auart_port(u);
- u32 ctrl = readl(u->membase + AUART_CTRL2);
+ u32 ctrl = readl(s->regs.ctrl2);
ctrl &= ~(AUART_CTRL2_RTSEN | AUART_CTRL2_RTS);
if (mctrl & TIOCM_RTS) {
@@ -415,14 +428,14 @@ static void mxs_auart_set_mctrl(struct uart_port *u, unsigned mctrl)
}
s->ctrl = mctrl;
- writel(ctrl, u->membase + AUART_CTRL2);
+ writel(ctrl, s->regs.ctrl2);
}
static u32 mxs_auart_get_mctrl(struct uart_port *u)
{
struct mxs_auart_port *s = to_auart_port(u);
- u32 stat = readl(u->membase + AUART_STAT);
- int ctrl2 = readl(u->membase + AUART_CTRL2);
+ u32 stat = readl(s->regs.stat);
+ int ctrl2 = readl(s->regs.ctrl2);
u32 mctrl = s->ctrl;
mctrl &= ~TIOCM_CTS;
@@ -445,14 +458,14 @@ static void dma_rx_callback(void *arg)
dma_unmap_sg(s->dev, &s->rx_sgl, 1, DMA_FROM_DEVICE);
- stat = readl(s->port.membase + AUART_STAT);
+ stat = readl(s->regs.stat);
stat &= ~(AUART_STAT_OERR | AUART_STAT_BERR |
AUART_STAT_PERR | AUART_STAT_FERR);
count = stat & AUART_STAT_RXCOUNT_MASK;
tty_insert_flip_string(port, s->rx_dma_buf, count);
- writel(stat, s->port.membase + AUART_STAT);
+ writel(stat, s->regs.stat);
tty_flip_buffer_push(port);
/* start the next DMA for RX. */
@@ -506,8 +519,8 @@ static void mxs_auart_dma_exit_channel(struct mxs_auart_port *s)
s->rx_dma_chan = NULL;
}
- kfree(s->tx_dma_buf);
- kfree(s->rx_dma_buf);
+ devm_kfree(s->dev, s->tx_dma_buf);
+ devm_kfree(s->dev, s->rx_dma_buf);
s->tx_dma_buf = NULL;
s->rx_dma_buf = NULL;
}
@@ -516,7 +529,7 @@ static void mxs_auart_dma_exit(struct mxs_auart_port *s)
{
writel(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR,
- s->port.membase + AUART_CTRL2_CLR);
+ s->regs.ctrl2 + CLR_REG);
mxs_auart_dma_exit_channel(s);
s->flags &= ~MXS_AUART_DMA_ENABLED;
@@ -533,7 +546,8 @@ static int mxs_auart_dma_init(struct mxs_auart_port *s)
s->rx_dma_chan = dma_request_slave_channel(s->dev, "rx");
if (!s->rx_dma_chan)
goto err_out;
- s->rx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
+ s->rx_dma_buf = devm_kzalloc(s->dev,
+ UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
if (!s->rx_dma_buf)
goto err_out;
@@ -541,7 +555,8 @@ static int mxs_auart_dma_init(struct mxs_auart_port *s)
s->tx_dma_chan = dma_request_slave_channel(s->dev, "tx");
if (!s->tx_dma_chan)
goto err_out;
- s->tx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
+ s->tx_dma_buf = devm_kzalloc(s->dev,
+ UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
if (!s->tx_dma_buf)
goto err_out;
@@ -571,7 +586,7 @@ static void mxs_auart_settermios(struct uart_port *u,
cflag = termios->c_cflag;
ctrl = AUART_LINECTRL_FEN;
- ctrl2 = readl(u->membase + AUART_CTRL2);
+ ctrl2 = readl(s->regs.ctrl2);
/* byte size */
switch (cflag & CSIZE) {
@@ -656,13 +671,21 @@ static void mxs_auart_settermios(struct uart_port *u,
}
/* set baud rate */
- baud = uart_get_baud_rate(u, termios, old, 0, u->uartclk);
- div = u->uartclk * 32 / baud;
+ if (is_asm9260_auart(s)) {
+ baud = uart_get_baud_rate(u, termios, old,
+ u->uartclk * 4 / 0x3FFFFF,
+ u->uartclk / 16);
+ div = u->uartclk * 4 / baud;
+ } else {
+ baud = uart_get_baud_rate(u, termios, old, 0, u->uartclk);
+ div = u->uartclk * 32 / baud;
+ }
+
ctrl |= AUART_LINECTRL_BAUD_DIVFRAC(div & 0x3F);
ctrl |= AUART_LINECTRL_BAUD_DIVINT(div >> 6);
+ writel(ctrl, s->regs.linectrl);
- writel(ctrl, u->membase + AUART_LINECTRL);
- writel(ctrl2, u->membase + AUART_CTRL2);
+ writel(ctrl2, s->regs.ctrl2);
uart_update_timeout(u, termios->c_cflag, baud);
@@ -672,7 +695,7 @@ static void mxs_auart_settermios(struct uart_port *u,
if (!mxs_auart_dma_prep_rx(s)) {
/* Disable the normal RX interrupt. */
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN,
- u->membase + AUART_INTR_CLR);
+ s->regs.intr + CLR_REG);
} else {
mxs_auart_dma_exit(s);
dev_err(s->dev, "We can not start up the DMA.\n");
@@ -684,21 +707,21 @@ static irqreturn_t mxs_auart_irq_handle(int irq, void *context)
{
u32 istat;
struct mxs_auart_port *s = context;
- u32 stat = readl(s->port.membase + AUART_STAT);
+ u32 stat = readl(s->regs.stat);
- istat = readl(s->port.membase + AUART_INTR);
+ istat = readl(s->regs.intr);
/* ack irq */
writel(istat & (AUART_INTR_RTIS
| AUART_INTR_TXIS
| AUART_INTR_RXIS
| AUART_INTR_CTSMIS),
- s->port.membase + AUART_INTR_CLR);
+ s->regs.intr + CLR_REG);
if (istat & AUART_INTR_CTSMIS) {
uart_handle_cts_change(&s->port, stat & AUART_STAT_CTS);
writel(AUART_INTR_CTSMIS,
- s->port.membase + AUART_INTR_CLR);
+ s->regs.intr + CLR_REG);
istat &= ~AUART_INTR_CTSMIS;
}
@@ -716,20 +739,20 @@ static irqreturn_t mxs_auart_irq_handle(int irq, void *context)
return IRQ_HANDLED;
}
-static void mxs_auart_reset(struct uart_port *u)
+static void mxs_auart_reset(struct mxs_auart_port *s)
{
int i;
unsigned int reg;
- writel(AUART_CTRL0_SFTRST, u->membase + AUART_CTRL0_CLR);
+ writel(AUART_CTRL0_SFTRST, s->regs.ctrl0 + CLR_REG);
for (i = 0; i < 10000; i++) {
- reg = readl(u->membase + AUART_CTRL0);
+ reg = readl(s->regs.ctrl0);
if (!(reg & AUART_CTRL0_SFTRST))
break;
udelay(3);
}
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
+ writel(AUART_CTRL0_CLKGATE, s->regs.ctrl0 + CLR_REG);
}
static int mxs_auart_startup(struct uart_port *u)
@@ -741,12 +764,12 @@ static int mxs_auart_startup(struct uart_port *u)
if (ret)
return ret;
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
+ writel(AUART_CTRL0_CLKGATE, s->regs.ctrl0 + CLR_REG);
- writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_SET);
+ writel(AUART_CTRL2_UARTEN, s->regs.ctrl2 + SET_REG);
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
- u->membase + AUART_INTR);
+ s->regs.intr);
/* Reset FIFO size (it could have changed if DMA was enabled) */
u->fifosize = MXS_AUART_FIFO_SIZE;
@@ -755,7 +778,7 @@ static int mxs_auart_startup(struct uart_port *u)
* Enable fifo so all four bytes of a DMA word are written to
* output (otherwise, only the LSB is written, ie. 1 in 4 bytes)
*/
- writel(AUART_LINECTRL_FEN, u->membase + AUART_LINECTRL_SET);
+ writel(AUART_LINECTRL_FEN, s->regs.linectrl + SET_REG);
return 0;
}
@@ -767,19 +790,21 @@ static void mxs_auart_shutdown(struct uart_port *u)
if (auart_dma_enabled(s))
mxs_auart_dma_exit(s);
- writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR);
+ writel(AUART_CTRL2_UARTEN, s->regs.ctrl2 + CLR_REG);
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
- u->membase + AUART_INTR_CLR);
+ s->regs.intr + CLR_REG);
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET);
+ writel(AUART_CTRL0_CLKGATE, s->regs.ctrl0 + SET_REG);
clk_disable_unprepare(s->clk);
}
static unsigned int mxs_auart_tx_empty(struct uart_port *u)
{
- if (readl(u->membase + AUART_STAT) & AUART_STAT_TXFE)
+ struct mxs_auart_port *s = to_auart_port(u);
+
+ if (readl(s->regs.stat) & AUART_STAT_TXFE)
return TIOCSER_TEMT;
else
return 0;
@@ -790,29 +815,35 @@ static void mxs_auart_start_tx(struct uart_port *u)
struct mxs_auart_port *s = to_auart_port(u);
/* enable transmitter */
- writel(AUART_CTRL2_TXE, u->membase + AUART_CTRL2_SET);
+ writel(AUART_CTRL2_TXE, s->regs.ctrl2 + SET_REG);
mxs_auart_tx_chars(s);
}
static void mxs_auart_stop_tx(struct uart_port *u)
{
- writel(AUART_CTRL2_TXE, u->membase + AUART_CTRL2_CLR);
+ struct mxs_auart_port *s = to_auart_port(u);
+
+ writel(AUART_CTRL2_TXE, s->regs.ctrl2 + CLR_REG);
}
static void mxs_auart_stop_rx(struct uart_port *u)
{
- writel(AUART_CTRL2_RXE, u->membase + AUART_CTRL2_CLR);
+ struct mxs_auart_port *s = to_auart_port(u);
+
+ writel(AUART_CTRL2_RXE, s->regs.ctrl2 + CLR_REG);
}
static void mxs_auart_break_ctl(struct uart_port *u, int ctl)
{
+ struct mxs_auart_port *s = to_auart_port(u);
+
if (ctl)
writel(AUART_LINECTRL_BRK,
- u->membase + AUART_LINECTRL_SET);
+ s->regs.linectrl + SET_REG);
else
writel(AUART_LINECTRL_BRK,
- u->membase + AUART_LINECTRL_CLR);
+ s->regs.linectrl + CLR_REG);
}
static struct uart_ops mxs_auart_ops = {
@@ -838,15 +869,16 @@ static struct mxs_auart_port *auart_port[MXS_AUART_PORTS];
#ifdef CONFIG_SERIAL_MXS_AUART_CONSOLE
static void mxs_auart_console_putchar(struct uart_port *port, int ch)
{
+ struct mxs_auart_port *s = to_auart_port(port);
unsigned int to = 1000;
- while (readl(port->membase + AUART_STAT) & AUART_STAT_TXFF) {
+ while (readl(s->regs.stat) & AUART_STAT_TXFF) {
if (!to--)
break;
udelay(1);
}
- writel(ch, port->membase + AUART_DATA);
+ writel(ch, s->regs.data);
}
static void
@@ -866,18 +898,18 @@ auart_console_write(struct console *co, const char *str, unsigned int count)
clk_enable(s->clk);
/* First save the CR then disable the interrupts */
- old_ctrl2 = readl(port->membase + AUART_CTRL2);
- old_ctrl0 = readl(port->membase + AUART_CTRL0);
+ old_ctrl2 = readl(s->regs.ctrl2);
+ old_ctrl0 = readl(s->regs.ctrl0);
writel(AUART_CTRL0_CLKGATE,
- port->membase + AUART_CTRL0_CLR);
+ s->regs.ctrl0 + CLR_REG);
writel(AUART_CTRL2_UARTEN | AUART_CTRL2_TXE,
- port->membase + AUART_CTRL2_SET);
+ s->regs.ctrl2 + SET_REG);
uart_console_write(port, str, count, mxs_auart_console_putchar);
/* Finally, wait for transmitter to become empty ... */
- while (readl(port->membase + AUART_STAT) & AUART_STAT_BUSY) {
+ while (readl(s->regs.stat) & AUART_STAT_BUSY) {
udelay(1);
if (!to--)
break;
@@ -889,24 +921,25 @@ auart_console_write(struct console *co, const char *str, unsigned int count)
* unused, but that is better than to disable it while it is still
* transmitting.
*/
- if (!(readl(port->membase + AUART_STAT) & AUART_STAT_BUSY)) {
- writel(old_ctrl0, port->membase + AUART_CTRL0);
- writel(old_ctrl2, port->membase + AUART_CTRL2);
+ if (!(readl(s->regs.stat) & AUART_STAT_BUSY)) {
+ writel(old_ctrl0, s->regs.ctrl0);
+ writel(old_ctrl2, s->regs.ctrl2);
}
clk_disable(s->clk);
}
static void __init
-auart_console_get_options(struct uart_port *port, int *baud,
+auart_console_get_options(struct mxs_auart_port *s, int *baud,
int *parity, int *bits)
{
+ struct uart_port *port = &s->port;
unsigned int lcr_h, quot;
- if (!(readl(port->membase + AUART_CTRL2) & AUART_CTRL2_UARTEN))
+ if (!(readl(s->regs.ctrl2) & AUART_CTRL2_UARTEN))
return;
- lcr_h = readl(port->membase + AUART_LINECTRL);
+ lcr_h = readl(s->regs.linectrl);
*parity = 'n';
if (lcr_h & AUART_LINECTRL_PEN) {
@@ -921,10 +954,10 @@ auart_console_get_options(struct uart_port *port, int *baud,
else
*bits = 8;
- quot = ((readl(port->membase + AUART_LINECTRL)
+ quot = ((readl(s->regs.linectrl)
& AUART_LINECTRL_BAUD_DIVINT_MASK))
>> (AUART_LINECTRL_BAUD_DIVINT_SHIFT - 6);
- quot |= ((readl(port->membase + AUART_LINECTRL)
+ quot |= ((readl(s->regs.linectrl)
& AUART_LINECTRL_BAUD_DIVFRAC_MASK))
>> AUART_LINECTRL_BAUD_DIVFRAC_SHIFT;
if (quot == 0)
@@ -950,6 +983,7 @@ auart_console_setup(struct console *co, char *options)
*/
if (co->index == -1 || co->index >= ARRAY_SIZE(auart_port))
co->index = 0;
+
s = auart_port[co->index];
if (!s)
return -ENODEV;
@@ -961,7 +995,7 @@ auart_console_setup(struct console *co, char *options)
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
- auart_console_get_options(&s->port, &baud, &parity, &bits);
+ auart_console_get_options(s, &baud, &parity, &bits);
ret = uart_set_options(&s->port, co, baud, parity, bits, flow);
@@ -971,7 +1005,7 @@ auart_console_setup(struct console *co, char *options)
}
static struct console auart_console = {
- .name = "ttyAPP",
+ .name = MXS_DEVICENAME,
.write = auart_console_write,
.device = uart_console_device,
.setup = auart_console_setup,
@@ -983,8 +1017,8 @@ static struct console auart_console = {
static struct uart_driver auart_driver = {
.owner = THIS_MODULE,
- .driver_name = "ttyAPP",
- .dev_name = "ttyAPP",
+ .driver_name = MXS_DEVICENAME,
+ .dev_name = MXS_DEVICENAME,
.major = 0,
.minor = 0,
.nr = MXS_AUART_PORTS,
@@ -993,6 +1027,58 @@ static struct uart_driver auart_driver = {
#endif
};
+static void mxs_init_regs(struct mxs_auart_port *s)
+{
+ s->regs.ctrl0 = s->port.membase + AUART_CTRL0;
+ s->regs.ctrl1 = s->port.membase + AUART_CTRL1;
+ s->regs.ctrl2 = s->port.membase + AUART_CTRL2;
+ s->regs.linectrl = s->port.membase + AUART_LINECTRL;
+
+ if (is_asm9260_auart(s)) {
+ s->regs.intr = s->port.membase + ASM9260_HW_INTR;
+ s->regs.data = s->port.membase + ASM9260_HW_DATA;
+ s->regs.stat = s->port.membase + ASM9260_HW_STAT;
+ } else {
+ s->regs.intr = s->port.membase + AUART_INTR;
+ s->regs.data = s->port.membase + AUART_DATA;
+ s->regs.stat = s->port.membase + AUART_STAT;
+ }
+}
+
+static int mxs_get_dt_clks(struct mxs_auart_port *s,
+ struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int clk_idx = 0, err;
+
+ s->clk = of_clk_get(np, clk_idx);
+ if (IS_ERR(s->clk))
+ goto out_err;
+
+ /* configure AHB clock */
+ clk_idx = 1;
+ s->clk_ahb = of_clk_get(np, clk_idx);
+ if (IS_ERR(s->clk_ahb))
+ goto out_err;
+
+ err = clk_prepare_enable(s->clk_ahb);
+ if (err)
+ dev_err(s->dev, "Failed to enable ahb_clk!\n");
+
+ err = clk_set_rate(s->clk, clk_get_rate(s->clk_ahb));
+ if (err)
+ dev_err(s->dev, "Failed to set rate!\n");
+
+ err = clk_prepare_enable(s->clk);
+ if (err)
+ dev_err(s->dev, "Failed to enable clk!\n");
+
+ return 0;
+out_err:
+ dev_err(s->dev, "%s: Failed to get clk (%i)\n", __func__, clk_idx);
+ return 1;
+}
+
/*
* This function returns 1 if pdev isn't a device instatiated by dt, 0 if it
* could successfully get all information from dt or a negative errno.
@@ -1029,77 +1115,98 @@ static int mxs_auart_probe(struct platform_device *pdev)
int ret = 0;
struct resource *r;
- s = kzalloc(sizeof(struct mxs_auart_port), GFP_KERNEL);
+ s = devm_kzalloc(&pdev->dev,
+ sizeof(struct mxs_auart_port), GFP_KERNEL);
if (!s) {
ret = -ENOMEM;
goto out;
}
+ s->port.dev = s->dev = &pdev->dev;
+
ret = serial_mxs_probe_dt(s, pdev);
if (ret > 0)
s->port.line = pdev->id < 0 ? 0 : pdev->id;
else if (ret < 0)
- goto out_free;
+ return ret;
if (of_id) {
pdev->id_entry = of_id->data;
s->devtype = pdev->id_entry->driver_data;
}
- s->clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(s->clk)) {
- ret = PTR_ERR(s->clk);
- goto out_free;
+ if (is_asm9260_auart(s)) {
+ if (mxs_get_dt_clks(s, pdev))
+ return -ENODEV;
+ } else {
+ s->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(s->clk))
+ return PTR_ERR(s->clk);
}
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!r) {
- ret = -ENXIO;
- goto out_free_clk;
+ dev_err(s->dev, "platform_get_resource filed!\n");
+ return -ENXIO;
+ }
+
+ if (!devm_request_mem_region(s->dev, r->start, resource_size(r),
+ dev_name(s->dev))) {
+ dev_err(s->dev, "request_mem_region filed!\n");
+ return -ENXIO;
+ }
+
+ s->port.membase = devm_ioremap_nocache(s->dev, r->start,
+ resource_size(r));
+ if (!s->port.membase) {
+ dev_err(s->dev, "ioremap filed!\n");
+ return -ENXIO;
}
s->port.mapbase = r->start;
- s->port.membase = ioremap(r->start, resource_size(r));
s->port.ops = &mxs_auart_ops;
s->port.iotype = UPIO_MEM;
s->port.fifosize = MXS_AUART_FIFO_SIZE;
s->port.uartclk = clk_get_rate(s->clk);
s->port.type = PORT_IMX;
- s->port.dev = s->dev = &pdev->dev;
+
+ mxs_init_regs(s);
s->ctrl = 0;
s->irq = platform_get_irq(pdev, 0);
s->port.irq = s->irq;
- ret = request_irq(s->irq, mxs_auart_irq_handle, 0, dev_name(&pdev->dev), s);
+ ret = devm_request_threaded_irq(s->dev, s->irq, NULL,
+ mxs_auart_irq_handle, IRQF_ONESHOT,
+ dev_name(&pdev->dev), s);
if (ret)
- goto out_free_clk;
+ return ret;
platform_set_drvdata(pdev, s);
auart_port[s->port.line] = s;
- mxs_auart_reset(&s->port);
+ mxs_auart_reset(s);
ret = uart_add_one_port(&auart_driver, &s->port);
if (ret)
- goto out_free_irq;
+ goto out;
+
- version = readl(s->port.membase + AUART_VERSION);
- dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n",
- (version >> 24) & 0xff,
- (version >> 16) & 0xff, version & 0xffff);
+ /* ASM9260 don't have version reg */
+ if (is_asm9260_auart(s))
+ dev_info(&pdev->dev, "Found APPUART ASM9260\n");
+ else {
+ version = readl(s->port.membase + AUART_VERSION);
+ dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n",
+ (version >> 24) & 0xff,
+ (version >> 16) & 0xff, version & 0xffff);
+ }
return 0;
-out_free_irq:
- auart_port[pdev->id] = NULL;
- free_irq(s->irq, s);
-out_free_clk:
- clk_put(s->clk);
-out_free:
- kfree(s);
out:
+ auart_port[pdev->id] = NULL;
return ret;
}
@@ -1110,11 +1217,6 @@ static int mxs_auart_remove(struct platform_device *pdev)
uart_remove_one_port(&auart_driver, &s->port);
auart_port[pdev->id] = NULL;
-
- clk_put(s->clk);
- free_irq(s->irq, s);
- kfree(s);
-
return 0;
}
@@ -1122,7 +1224,7 @@ static struct platform_driver mxs_auart_driver = {
.probe = mxs_auart_probe,
.remove = mxs_auart_remove,
.driver = {
- .name = "mxs-auart",
+ .name = DRIVER_NAME,
.owner = THIS_MODULE,
.of_match_table = mxs_auart_dt_ids,
},
@@ -1157,4 +1259,4 @@ module_init(mxs_auart_init);
module_exit(mxs_auart_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Freescale MXS application uart driver");
-MODULE_ALIAS("platform:mxs-auart");
+MODULE_ALIAS("platform:" DRIVER_NAME);
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 08/10] add Alphascale to vendor-prefixes.txt
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (6 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 07/10] tty/serial/mxs-auart.c: add initial Alphascale ASM9260 support Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 23:19 ` Rob Herring
2014-10-12 19:19 ` [PATCH v4 09/10] irqchip: mxs: prepare driver for HW with different offsets Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 10/10] irqchip: mxs: add Alpascale ASM9260 support Oleksij Rempel
9 siblings, 1 reply; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
this company already provided some products, so it make sense to add
them to vendor-prefixes.txt list
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ac7269f..23c862f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -11,6 +11,7 @@ adi Analog Devices, Inc.
aeroflexgaisler Aeroflex Gaisler AB
ak Asahi Kasei Corp.
allwinner Allwinner Technology Co., Ltd.
+alphascale AlphaScale Integrated Circuits Systems, Inc.
altr Altera Corp.
amcc Applied Micro Circuits Corporation (APM, formally AMCC)
amd Advanced Micro Devices (AMD), Inc.
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 08/10] add Alphascale to vendor-prefixes.txt
2014-10-12 19:19 ` [PATCH v4 08/10] add Alphascale to vendor-prefixes.txt Oleksij Rempel
@ 2014-10-12 23:19 ` Rob Herring
2014-10-13 10:44 ` Oleksij Rempel
0 siblings, 1 reply; 18+ messages in thread
From: Rob Herring @ 2014-10-12 23:19 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Oct 12, 2014 at 2:19 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
> this company already provided some products, so it make sense to add
> them to vendor-prefixes.txt list
>
> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Acked-by: Rob Herring <robh@kernel.org>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index ac7269f..23c862f 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -11,6 +11,7 @@ adi Analog Devices, Inc.
> aeroflexgaisler Aeroflex Gaisler AB
> ak Asahi Kasei Corp.
> allwinner Allwinner Technology Co., Ltd.
> +alphascale AlphaScale Integrated Circuits Systems, Inc.
> altr Altera Corp.
> amcc Applied Micro Circuits Corporation (APM, formally AMCC)
> amd Advanced Micro Devices (AMD), Inc.
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 08/10] add Alphascale to vendor-prefixes.txt
2014-10-12 23:19 ` Rob Herring
@ 2014-10-13 10:44 ` Oleksij Rempel
0 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-13 10:44 UTC (permalink / raw)
To: linux-arm-kernel
Do it make sense to push this patch separately? Right now it looks like
this patch set will be pingponged some more times :/
Am 13.10.2014 um 01:19 schrieb Rob Herring:
> On Sun, Oct 12, 2014 at 2:19 PM, Oleksij Rempel <linux@rempel-privat.de> wrote:
>> this company already provided some products, so it make sense to add
>> them to vendor-prefixes.txt list
>>
>> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
>
> Acked-by: Rob Herring <robh@kernel.org>
>
>> ---
>> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>> 1 file changed, 1 insertion(+)
>>
>> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> index ac7269f..23c862f 100644
>> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
>> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> @@ -11,6 +11,7 @@ adi Analog Devices, Inc.
>> aeroflexgaisler Aeroflex Gaisler AB
>> ak Asahi Kasei Corp.
>> allwinner Allwinner Technology Co., Ltd.
>> +alphascale AlphaScale Integrated Circuits Systems, Inc.
>> altr Altera Corp.
>> amcc Applied Micro Circuits Corporation (APM, formally AMCC)
>> amd Advanced Micro Devices (AMD), Inc.
>> --
>> 1.9.1
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Regards,
Oleksij
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 213 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20141013/3fc3d183/attachment.sig>
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v4 09/10] irqchip: mxs: prepare driver for HW with different offsets
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (7 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 08/10] add Alphascale to vendor-prefixes.txt Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
2014-10-12 19:19 ` [PATCH v4 10/10] irqchip: mxs: add Alpascale ASM9260 support Oleksij Rempel
9 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
Some HW has similar functionality but different register offsets.
Make sure we can change offsets dynamically.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
drivers/irqchip/irq-mxs.c | 55 ++++++++++++++++++++++++++++++++++++-----------
1 file changed, 42 insertions(+), 13 deletions(-)
diff --git a/drivers/irqchip/irq-mxs.c b/drivers/irqchip/irq-mxs.c
index e4acf1e..681125d 100644
--- a/drivers/irqchip/irq-mxs.c
+++ b/drivers/irqchip/irq-mxs.c
@@ -29,18 +29,39 @@
#include "irqchip.h"
+/*
+ * this device provide 4 offsets for each register:
+ * 0x0 - plain read write mode
+ * 0x4 - set mode, OR logic.
+ * 0x8 - clr mode, XOR logic.
+ * 0xc - togle mode.
+ */
+#define SET_REG 4
+#define CLR_REG 8
+
#define HW_ICOLL_VECTOR 0x0000
#define HW_ICOLL_LEVELACK 0x0010
#define HW_ICOLL_CTRL 0x0020
#define HW_ICOLL_STAT_OFFSET 0x0070
-#define HW_ICOLL_INTERRUPTn_SET(n) (0x0124 + (n) * 0x10)
-#define HW_ICOLL_INTERRUPTn_CLR(n) (0x0128 + (n) * 0x10)
-#define BM_ICOLL_INTERRUPTn_ENABLE 0x00000004
+#define HW_ICOLL_INTERRUPT0 0x0120
+#define HW_ICOLL_INTERRUPTn(n) ((n) * 0x10)
+#define BM_ICOLL_INTR_ENABLE BIT(2)
#define BV_ICOLL_LEVELACK_IRQLEVELACK__LEVEL0 0x1
#define ICOLL_NUM_IRQS 128
-static void __iomem *icoll_base;
+struct icoll_priv {
+ void __iomem *vector;
+ void __iomem *levelack;
+ void __iomem *ctrl;
+ void __iomem *stat;
+ void __iomem *intr;
+ /* number of interrupts per register */
+ int intr_per_reg;
+ void __iomem *clear;
+};
+
+static struct icoll_priv icoll_priv;
static struct irq_domain *icoll_domain;
static void icoll_ack_irq(struct irq_data *d)
@@ -51,19 +72,19 @@ static void icoll_ack_irq(struct irq_data *d)
* BV_ICOLL_LEVELACK_IRQLEVELACK__LEVEL0 unconditionally.
*/
__raw_writel(BV_ICOLL_LEVELACK_IRQLEVELACK__LEVEL0,
- icoll_base + HW_ICOLL_LEVELACK);
+ icoll_priv.levelack);
}
static void icoll_mask_irq(struct irq_data *d)
{
- __raw_writel(BM_ICOLL_INTERRUPTn_ENABLE,
- icoll_base + HW_ICOLL_INTERRUPTn_CLR(d->hwirq));
+ __raw_writel(BM_ICOLL_INTR_ENABLE,
+ icoll_priv.intr + CLR_REG + HW_ICOLL_INTERRUPTn(d->hwirq));
}
static void icoll_unmask_irq(struct irq_data *d)
{
- __raw_writel(BM_ICOLL_INTERRUPTn_ENABLE,
- icoll_base + HW_ICOLL_INTERRUPTn_SET(d->hwirq));
+ __raw_writel(BM_ICOLL_INTR_ENABLE,
+ icoll_priv.intr + SET_REG + HW_ICOLL_INTERRUPTn(d->hwirq));
}
static struct irq_chip mxs_icoll_chip = {
@@ -76,8 +97,8 @@ asmlinkage void __exception_irq_entry icoll_handle_irq(struct pt_regs *regs)
{
u32 irqnr;
- irqnr = __raw_readl(icoll_base + HW_ICOLL_STAT_OFFSET);
- __raw_writel(irqnr, icoll_base + HW_ICOLL_VECTOR);
+ irqnr = __raw_readl(icoll_priv.stat);
+ __raw_writel(irqnr, icoll_priv.vector);
handle_domain_irq(icoll_domain, irqnr, regs);
}
@@ -98,14 +119,22 @@ static struct irq_domain_ops icoll_irq_domain_ops = {
static int __init icoll_of_init(struct device_node *np,
struct device_node *interrupt_parent)
{
- icoll_base = of_iomap(np, 0);
+ void __iomem *icoll_base = of_iomap(np, 0);
WARN_ON(!icoll_base);
+ icoll_priv.vector = icoll_base + HW_ICOLL_VECTOR;
+ icoll_priv.levelack = icoll_base + HW_ICOLL_LEVELACK;
+ icoll_priv.ctrl = icoll_base + HW_ICOLL_CTRL;
+ icoll_priv.stat = icoll_base + HW_ICOLL_STAT_OFFSET;
+ icoll_priv.intr = icoll_base + HW_ICOLL_INTERRUPT0;
+ icoll_priv.intr_per_reg = 1;
+ icoll_priv.clear = NULL;
+
/*
* Interrupt Collector reset, which initializes the priority
* for each irq to level 0.
*/
- stmp_reset_block(icoll_base + HW_ICOLL_CTRL);
+ stmp_reset_block(icoll_priv.ctrl);
icoll_domain = irq_domain_add_linear(np, ICOLL_NUM_IRQS,
&icoll_irq_domain_ops, NULL);
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH v4 10/10] irqchip: mxs: add Alpascale ASM9260 support
2014-10-12 19:19 [PATCH v4 00/10] initial suport for Alphascale ASM9260 Oleksij Rempel
` (8 preceding siblings ...)
2014-10-12 19:19 ` [PATCH v4 09/10] irqchip: mxs: prepare driver for HW with different offsets Oleksij Rempel
@ 2014-10-12 19:19 ` Oleksij Rempel
9 siblings, 0 replies; 18+ messages in thread
From: Oleksij Rempel @ 2014-10-12 19:19 UTC (permalink / raw)
To: linux-arm-kernel
Freescale iMX23/iMX28 and Alphascale ASM9260 have similar
interrupt collectors. It makes easy to reuse irq-mxs code for ASM9260.
Differences between this devices are fallowing:
- different register offsets
- different count of intterupt lines per register
- ASM9260 don't provide reset bit
- ASM9260 don't support FIQ.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
---
drivers/irqchip/Kconfig | 5 ++
drivers/irqchip/Makefile | 2 +-
drivers/irqchip/alphascale_asm9260-icoll.h | 109 ++++++++++++++++++++++++++++
drivers/irqchip/irq-mxs.c | 112 ++++++++++++++++++++++++++---
4 files changed, 219 insertions(+), 9 deletions(-)
create mode 100644 drivers/irqchip/alphascale_asm9260-icoll.h
diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index b8632bf..2ee202f 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -113,3 +113,8 @@ config IRQ_CROSSBAR
The primary irqchip invokes the crossbar's callback which inturn allocates
a free irq and configures the IP. Thus the peripheral interrupts are
routed to one of the free irqchip interrupt lines.
+
+config IRQ_MXS
+ bool
+ select IRQ_DOMAIN
+ select STMP_DEVICE
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index 73052ba..89c7042 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -4,7 +4,7 @@ obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o
obj-$(CONFIG_ARCH_EXYNOS) += exynos-combiner.o
obj-$(CONFIG_ARCH_MMP) += irq-mmp.o
obj-$(CONFIG_ARCH_MVEBU) += irq-armada-370-xp.o
-obj-$(CONFIG_ARCH_MXS) += irq-mxs.o
+obj-$(CONFIG_IRQ_MXS) += irq-mxs.o
obj-$(CONFIG_ARCH_S3C24XX) += irq-s3c24xx.o
obj-$(CONFIG_DW_APB_ICTL) += irq-dw-apb-ictl.o
obj-$(CONFIG_METAG) += irq-metag-ext.o
diff --git a/drivers/irqchip/alphascale_asm9260-icoll.h b/drivers/irqchip/alphascale_asm9260-icoll.h
new file mode 100644
index 0000000..5cec108
--- /dev/null
+++ b/drivers/irqchip/alphascale_asm9260-icoll.h
@@ -0,0 +1,109 @@
+/*
+ * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _ALPHASCALE_ASM9260_ICOLL_H
+#define _ALPHASCALE_ASM9260_ICOLL_H
+
+#define ASM9260_NUM_IRQS 64
+/*
+ * this device provide 4 offsets for each register:
+ * 0x0 - plain read write mode
+ * 0x4 - set mode, OR logic.
+ * 0x8 - clr mode, XOR logic.
+ * 0xc - togle mode.
+ */
+
+#define ASM9260_HW_ICOLL_VECTOR 0x0000
+/*
+ * bits 31:2
+ * This register presents the vector address for the interrupt currently
+ * active on the CPU IRQ input. Writing to this register notifies the
+ * interrupt collector that the interrupt service routine for the current
+ * interrupt has been entered.
+ * The exception trap should have a LDPC instruction from this address:
+ * LDPC ASM9260_HW_ICOLL_VECTOR_ADDR; IRQ exception at 0xffff0018
+ */
+
+/*
+ * The Interrupt Collector Level Acknowledge Register is used by software to
+ * indicate the completion of an interrupt on a specific level.
+ * This register is written at the very end of an interrupt service routine. If
+ * nesting is used then the CPU irq must be turned on before writing to this
+ * register to avoid a race condition in the CPU interrupt hardware.
+ */
+#define ASM9260_HW_ICOLL_LEVELACK 0x0010
+#define ASM9260_BM_LEVELn(nr) BIT(nr)
+
+#define ASM9260_HW_ICOLL_CTRL 0x0020
+/*
+ * ASM9260_BM_CTRL_SFTRST and ASM9260_BM_CTRL_CLKGATE are not available on
+ * asm9260.
+ */
+#define ASM9260_BM_CTRL_SFTRST BIT(31)
+#define ASM9260_BM_CTRL_CLKGATE BIT(30)
+/* disable interrupt level nesting */
+#define ASM9260_BM_CTRL_NO_NESTING BIT(19)
+/*
+ * Set this bit to one enable the RISC32-style read side effect associated with
+ * the vector address register. In this mode, interrupt in-service is signaled
+ * by the read of the ASM9260_HW_ICOLL_VECTOR register to acquire the interrupt
+ * vector address. Set this bit to zero for normal operation, in which the ISR
+ * signals in-service explicitly by means of a write to the
+ * ASM9260_HW_ICOLL_VECTOR register.
+ * 0 - Must Write to Vector register to go in-service.
+ * 1 - Go in-service as a read side effect
+ */
+#define ASM9260_BM_CTRL_ARM_RSE_MODE BIT(18)
+#define ASM9260_BM_CTRL_IRQ_ENABLE BIT(16)
+
+#define ASM9260_HW_ICOLL_STAT_OFFSET 0x0030
+/*
+ * bits 5:0
+ * Vector number of current interrupt. Multiply by 4 and add to vector base
+ * address to obtain the value in ASM9260_HW_ICOLL_VECTOR.
+ */
+
+/*
+ * RAW0 and RAW1 provides a read-only view of the raw interrupt request lines
+ * coming from various parts of the chip. Its purpose is to improve diagnostic
+ * observability.
+ */
+#define ASM9260_HW_ICOLL_RAW0 0x0040
+#define ASM9260_HW_ICOLL_RAW1 0x0050
+
+#define ASM9260_HW_ICOLL_INTERRUPT0 0x0060
+#define ASM9260_HW_ICOLL_INTERRUPTn(n) (0x0060 + ((n) >> 2) * 0x10)
+/*
+ * WARNING: Modifying the priority of an enabled interrupt may result in
+ * undefined behavior.
+ */
+#define ASM9260_BM_INT_PRIORITY_MASK 0x3
+#define ASM9260_BM_INT_ENABLE BIT(2)
+#define ASM9260_BM_INT_SOFTIRQ BIT(3)
+
+#define ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n) (((n) & 0x3) << 3)
+#define ASM9260_BM_ICOLL_INTERRUPTn_ENABLE(n) (1 << (2 + \
+ ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n)))
+
+#define ASM9260_HW_ICOLL_VBASE 0x0160
+/*
+ * bits 31:2
+ * This bitfield holds the upper 30 bits of the base address of the vector
+ * table.
+ */
+
+#define ASM9260_HW_ICOLL_CLEAR0 0x01d0
+#define ASM9260_HW_ICOLL_CLEAR1 0x01e0
+#define ASM9260_HW_ICOLL_CLEARn(n) (((n >> 5) * 0x10) \
+ + SET_REG)
+#define ASM9260_BM_CLEAR_BIT(n) BIT(n & 0x1f)
+
+/* Scratchpad */
+#define ASM9260_HW_ICOLL_UNDEF_VECTOR 0x01f0
+#endif
diff --git a/drivers/irqchip/irq-mxs.c b/drivers/irqchip/irq-mxs.c
index 681125d..8397c73 100644
--- a/drivers/irqchip/irq-mxs.c
+++ b/drivers/irqchip/irq-mxs.c
@@ -1,5 +1,7 @@
/*
* Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de>
+ * Add Alphascale ASM9260 support.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -28,6 +30,7 @@
#include <asm/exception.h>
#include "irqchip.h"
+#include "alphascale_asm9260-icoll.h"
/*
* this device provide 4 offsets for each register:
@@ -63,6 +66,33 @@ struct icoll_priv {
static struct icoll_priv icoll_priv;
static struct irq_domain *icoll_domain;
+static DEFINE_MUTEX(icoll_lock);
+
+/* calculate bit offset depending on number of intterupt per register */
+static u32 icoll_intr_bitshift(struct irq_data *d, u32 bit)
+{
+ /*
+ * We expect intr_per_reg to be 4 or 1, it means
+ * "n" will be 3 or 0.
+ */
+ int n = icoll_priv.intr_per_reg - 1;
+
+ /*
+ * If n = 0, "bit" is never shifted.
+ * If n = 3, mask lower part of hwirq to convert it
+ * in 0, 1, 2 or 3 and then multiply it by 8 (or shift by 3)
+ */
+ return bit << ((d->hwirq & n) << n);
+}
+
+/* calculate mem offset depending on number of intterupt per register */
+static void __iomem *icoll_intr_reg(struct irq_data *d)
+{
+ int n = icoll_priv.intr_per_reg >> 1;
+
+ /* offset = hwirq / intr_per_reg * 0x10 */
+ return icoll_priv.intr + ((d->hwirq >> n) * 0x10);
+}
static void icoll_ack_irq(struct irq_data *d)
{
@@ -77,14 +107,21 @@ static void icoll_ack_irq(struct irq_data *d)
static void icoll_mask_irq(struct irq_data *d)
{
- __raw_writel(BM_ICOLL_INTR_ENABLE,
- icoll_priv.intr + CLR_REG + HW_ICOLL_INTERRUPTn(d->hwirq));
+ __raw_writel(icoll_intr_bitshift(d, BM_ICOLL_INTR_ENABLE),
+ icoll_intr_reg(d) + CLR_REG);
}
static void icoll_unmask_irq(struct irq_data *d)
{
- __raw_writel(BM_ICOLL_INTR_ENABLE,
- icoll_priv.intr + SET_REG + HW_ICOLL_INTERRUPTn(d->hwirq));
+ mutex_lock(&icoll_lock);
+ if (icoll_priv.clear)
+ __raw_writel(ASM9260_BM_CLEAR_BIT(d->hwirq),
+ icoll_priv.clear +
+ ASM9260_HW_ICOLL_CLEARn(d->hwirq));
+
+ __raw_writel(icoll_intr_bitshift(d, BM_ICOLL_INTR_ENABLE),
+ icoll_intr_reg(d) + SET_REG);
+ mutex_unlock(&icoll_lock);
}
static struct irq_chip mxs_icoll_chip = {
@@ -116,12 +153,41 @@ static struct irq_domain_ops icoll_irq_domain_ops = {
.xlate = irq_domain_xlate_onecell,
};
+static void __init icoll_add_domain(struct device_node *np,
+ int num)
+{
+ icoll_domain = irq_domain_add_linear(np, num,
+ &icoll_irq_domain_ops, NULL);
+
+ if (!icoll_domain)
+ panic("%s: unable add irq domain", np->full_name);
+ irq_set_default_host(icoll_domain);
+ set_handle_irq(icoll_handle_irq);
+}
+
+static void __iomem * __init icoll_init_iobase(struct device_node *np)
+{
+ struct resource res;
+ void __iomem *icoll_base;
+
+ if (of_address_to_resource(np, 0, &res))
+ panic("%s: unable to get resource", np->full_name);
+
+ if (!request_mem_region(res.start, resource_size(&res), np->name))
+ panic("%s: unable to request mem region", np->full_name);
+
+ icoll_base = ioremap_nocache(res.start, resource_size(&res));
+ if (!icoll_base)
+ panic("%s: unable to map resource", np->full_name);
+ return icoll_base;
+}
+
static int __init icoll_of_init(struct device_node *np,
struct device_node *interrupt_parent)
{
- void __iomem *icoll_base = of_iomap(np, 0);
- WARN_ON(!icoll_base);
+ void __iomem *icoll_base;
+ icoll_base = icoll_init_iobase(np);
icoll_priv.vector = icoll_base + HW_ICOLL_VECTOR;
icoll_priv.levelack = icoll_base + HW_ICOLL_LEVELACK;
icoll_priv.ctrl = icoll_base + HW_ICOLL_CTRL;
@@ -136,8 +202,38 @@ static int __init icoll_of_init(struct device_node *np,
*/
stmp_reset_block(icoll_priv.ctrl);
- icoll_domain = irq_domain_add_linear(np, ICOLL_NUM_IRQS,
- &icoll_irq_domain_ops, NULL);
+ icoll_add_domain(np, ICOLL_NUM_IRQS);
+
return icoll_domain ? 0 : -ENODEV;
}
IRQCHIP_DECLARE(mxs, "fsl,icoll", icoll_of_init);
+
+static int __init asm9260_of_init(struct device_node *np,
+ struct device_node *interrupt_parent)
+{
+ void __iomem *icoll_base;
+ int i;
+
+ icoll_base = icoll_init_iobase(np);
+ icoll_priv.vector = icoll_base + ASM9260_HW_ICOLL_VECTOR;
+ icoll_priv.levelack = icoll_base + ASM9260_HW_ICOLL_LEVELACK;
+ icoll_priv.ctrl = icoll_base + ASM9260_HW_ICOLL_CTRL;
+ icoll_priv.stat = icoll_base + ASM9260_HW_ICOLL_STAT_OFFSET;
+ icoll_priv.intr = icoll_base + ASM9260_HW_ICOLL_INTERRUPT0;
+ icoll_priv.intr_per_reg = 4;
+ icoll_priv.clear = icoll_base + ASM9260_HW_ICOLL_CLEAR0;
+
+ writel_relaxed(ASM9260_BM_CTRL_IRQ_ENABLE,
+ icoll_priv.ctrl);
+ /*
+ * ASM9260 don't provide reset bit. So, we need to set level 0
+ * manually.
+ */
+ for (i = 0; i < 16 * 0x10; i += 0x10)
+ writel(0, icoll_priv.intr + i);
+
+ icoll_add_domain(np, ASM9260_NUM_IRQS);
+
+ return icoll_domain ? 0 : -ENODEV;
+}
+IRQCHIP_DECLARE(asm9260, "alphascale,asm9260-icoll", asm9260_of_init);
--
1.9.1
^ permalink raw reply related [flat|nested] 18+ messages in thread