From: mlangsdo@redhat.com (Mark Langsdorf)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/2] [usb] add support for APM X-Gene to xhci-platform
Date: Thu, 30 Oct 2014 13:16:29 -0500 [thread overview]
Message-ID: <1414692989-23128-3-git-send-email-mlangsdo@redhat.com> (raw)
In-Reply-To: <1414692989-23128-1-git-send-email-mlangsdo@redhat.com>
Applied Micro's X-Gene platform uses the xhci-platform for USB.
Add the glue to decode it from ACPI and change the Kconfig files
so the xhci-plat.o file gets built.
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
---
arch/arm64/Kconfig | 1 +
drivers/usb/host/Kconfig | 8 ++++++++
drivers/usb/host/xhci-plat.c | 11 +++++++++++
3 files changed, 20 insertions(+)
diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 042f785..07549ec 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -149,6 +149,7 @@ config ARCH_XGENE
bool "AppliedMicro X-Gene SOC Family"
select MFD_SYSCON
select POWER_RESET_SYSCON
+ select USB_XHCI_XGENE
help
This enables support for AppliedMicro X-Gene SOC Family
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 82800a7..9fd52db 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -45,6 +45,14 @@ config USB_XHCI_RCAR
Say 'Y' to enable the support for the xHCI host controller
found in Renesas R-Car ARM SoCs.
+config USB_XHCI_XGENE
+ tristate "xHCI support for Applied Micro X-Gene SoCs"
+ select USB_XHCI_PLATFORM
+ depends on ARCH_XGENE || COMPILE_TEST
+ ---help---
+ Say 'Y' to enable the support for the xHCI host controller
+ found in Applied Micro X-Gene ARM SoCs.
+
endif # USB_XHCI_HCD
config USB_EHCI_HCD
diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
index 3045e77..5012c68 100644
--- a/drivers/usb/host/xhci-plat.c
+++ b/drivers/usb/host/xhci-plat.c
@@ -18,6 +18,7 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/usb/xhci_pdriver.h>
+#include <linux/acpi.h>
#include "xhci.h"
#include "xhci-mvebu.h"
@@ -290,6 +291,15 @@ static const struct of_device_id usb_xhci_of_match[] = {
MODULE_DEVICE_TABLE(of, usb_xhci_of_match);
#endif
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id usb_xhci_acpi_match[] = {
+ /* APM X-Gene USB Controller */
+ { "PNP0D10", },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, usb_xhci_acpi_match);
+#endif
+
static struct platform_driver usb_xhci_driver = {
.probe = xhci_plat_probe,
.remove = xhci_plat_remove,
@@ -297,6 +307,7 @@ static struct platform_driver usb_xhci_driver = {
.name = "xhci-hcd",
.pm = DEV_PM_OPS,
.of_match_table = of_match_ptr(usb_xhci_of_match),
+ .acpi_match_table = ACPI_PTR(usb_xhci_acpi_match),
},
};
MODULE_ALIAS("platform:xhci-hcd");
--
1.9.3
next prev parent reply other threads:[~2014-10-30 18:16 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-30 18:16 [usb] add support for APM X-Gene to xhci-platform Mark Langsdorf
2014-10-30 18:16 ` [PATCH 1/2] [usb] make xhci platform driver use 64 bit or 32 bit DMA Mark Langsdorf
2014-10-30 19:05 ` Arnd Bergmann
2014-10-30 20:09 ` Mark Langsdorf
2014-10-30 21:05 ` Arnd Bergmann
2014-10-31 14:22 ` Mark Langsdorf
2014-10-31 15:49 ` Arnd Bergmann
2014-10-31 17:32 ` Mark Langsdorf
2014-10-31 19:41 ` Arnd Bergmann
2014-11-03 14:15 ` Mark Salter
2014-11-03 17:14 ` Arnd Bergmann
2014-11-03 18:45 ` Mark Salter
2014-11-04 17:33 ` Al Stone
2014-11-06 0:03 ` Arnd Bergmann
2014-11-04 16:50 ` [PATCH v2 " Mark Langsdorf
2014-11-04 16:50 ` [PATCH v2 2/2] [usb] add support for ACPI identification to xhci-platform Mark Langsdorf
2014-11-04 17:12 ` Greg KH
2014-11-05 13:59 ` Mark Langsdorf
2014-11-05 19:11 ` Greg KH
2014-11-05 19:44 ` Mark Langsdorf
2014-11-05 19:55 ` Greg KH
2014-11-05 20:41 ` Arnd Bergmann
2014-11-05 22:05 ` Greg KH
2014-11-13 18:36 ` Mark Langsdorf
2014-11-13 19:08 ` Greg KH
2014-11-18 20:05 ` Feng Kan
2014-11-18 20:33 ` Mark Langsdorf
2014-11-18 21:11 ` Feng Kan
2014-10-30 18:16 ` Mark Langsdorf [this message]
2014-10-30 19:07 ` [PATCH 2/2] [usb] add support for APM X-Gene " Arnd Bergmann
2014-10-30 20:12 ` Mark Langsdorf
2014-10-30 20:53 ` Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1414692989-23128-3-git-send-email-mlangsdo@redhat.com \
--to=mlangsdo@redhat.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).