From mboxrd@z Thu Jan 1 00:00:00 1970 From: maxime.ripard@free-electrons.com (Maxime Ripard) Date: Sun, 1 Feb 2015 14:50:10 +0100 Subject: [PATCH 26/30] ARM: sun7i: olinuxino lime: Convert to DT label based syntax In-Reply-To: <1422798614-3581-1-git-send-email-maxime.ripard@free-electrons.com> References: <1422798614-3581-1-git-send-email-maxime.ripard@free-electrons.com> Message-ID: <1422798614-3581-27-git-send-email-maxime.ripard@free-electrons.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts | 186 ++++++++++++------------- 1 file changed, 92 insertions(+), 94 deletions(-) diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts index 12ded69d61eb..68efd2f33307 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts @@ -60,118 +60,116 @@ model = "Olimex A20-OLinuXino-LIME"; compatible = "olimex,a20-olinuxino-lime", "allwinner,sun7i-a20"; - soc at 01c00000 { - mmc0: mmc at 01c0f000 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; - vmmc-supply = <®_vcc3v3>; - bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; - status = "okay"; - }; + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_olinuxinolime>; - usbphy: phy at 01c13400 { - usb1_vbus-supply = <®_usb1_vbus>; - usb2_vbus-supply = <®_usb2_vbus>; - status = "okay"; + green { + label = "a20-olinuxino-lime:green:usr"; + gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; + default-state = "on"; }; + }; +}; - ehci0: usb at 01c14000 { - status = "okay"; - }; +&ahci { + target-supply = <®_ahci_5v>; + status = "okay"; +}; - ohci0: usb at 01c14400 { - status = "okay"; - }; +&ehci0 { + status = "okay"; +}; - ahci: sata at 01c18000 { - target-supply = <®_ahci_5v>; - status = "okay"; - }; +&ehci1 { + status = "okay"; +}; - ehci1: usb at 01c1c000 { - status = "okay"; - }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + status = "okay"; - ohci1: usb at 01c1c400 { - status = "okay"; - }; + phy1: ethernet-phy at 1 { + reg = <1>; + }; +}; - pinctrl at 01c20800 { - ahci_pwr_pin_olinuxinolime: ahci_pwr_pin at 1 { - allwinner,pins = "PC3"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - - led_pins_olinuxinolime: led_pins at 0 { - allwinner,pins = "PH2"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - }; +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; - uart0: serial at 01c28000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; - }; + axp209: pmic at 34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + + interrupt-controller; + #interrupt-cells = <1>; + }; +}; - i2c0: i2c at 01c2ac00 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; - axp209: pmic at 34 { - compatible = "x-powers,axp209"; - reg = <0x34>; - interrupt-parent = <&nmi_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; +&ohci0 { + status = "okay"; +}; - interrupt-controller; - #interrupt-cells = <1>; - }; - }; +&ohci1 { + status = "okay"; +}; - gmac: ethernet at 01c50000 { - pinctrl-names = "default"; - pinctrl-0 = <&gmac_pins_mii_a>; - phy = <&phy1>; - phy-mode = "mii"; - status = "okay"; +&pio { + ahci_pwr_pin_olinuxinolime: ahci_pwr_pin at 1 { + allwinner,pins = "PC3"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; - phy1: ethernet-phy at 1 { - reg = <1>; - }; - }; + led_pins_olinuxinolime: led_pins at 0 { + allwinner,pins = "PH2"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; }; +}; - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins_olinuxinolime>; +®_ahci_5v { + pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>; + gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; - green { - label = "a20-olinuxino-lime:green:usr"; - gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - }; +®_usb1_vbus { + status = "okay"; +}; - reg_ahci_5v: ahci-5v { - pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>; - gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>; - status = "okay"; - }; +®_usb2_vbus { + status = "okay"; +}; - reg_usb1_vbus: usb1-vbus { - status = "okay"; - }; +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; - reg_usb2_vbus: usb2-vbus { - status = "okay"; - }; +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; }; -- 2.2.2