From mboxrd@z Thu Jan 1 00:00:00 1970 From: maxime.ripard@free-electrons.com (Maxime Ripard) Date: Wed, 11 Feb 2015 10:01:03 +0100 Subject: [PATCH v2 04/30] ARM: sun4i: a1000: Convert to DT label based syntax In-Reply-To: <1423645289-1074-1-git-send-email-maxime.ripard@free-electrons.com> References: <1423645289-1074-1-git-send-email-maxime.ripard@free-electrons.com> Message-ID: <1423645289-1074-5-git-send-email-maxime.ripard@free-electrons.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-a1000.dts | 200 +++++++++++++++++----------------- 1 file changed, 99 insertions(+), 101 deletions(-) diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts index b67e5be618cf..648626bc58a1 100644 --- a/arch/arm/boot/dts/sun4i-a10-a1000.dts +++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts @@ -58,103 +58,6 @@ model = "Mele A1000"; compatible = "mele,a1000", "allwinner,sun4i-a10"; - soc at 01c00000 { - emac: ethernet at 01c0b000 { - pinctrl-names = "default"; - pinctrl-0 = <&emac_pins_a>; - phy = <&phy1>; - status = "okay"; - }; - - mdio at 01c0b080 { - phy-supply = <®_emac_3v3>; - status = "okay"; - - phy1: ethernet-phy at 1 { - reg = <1>; - }; - }; - - mmc0: mmc at 01c0f000 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; - vmmc-supply = <®_vcc3v3>; - bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; - status = "okay"; - }; - - usbphy: phy at 01c13400 { - usb1_vbus-supply = <®_usb1_vbus>; - usb2_vbus-supply = <®_usb2_vbus>; - status = "okay"; - }; - - ehci0: usb at 01c14000 { - status = "okay"; - }; - - ohci0: usb at 01c14400 { - status = "okay"; - }; - - ahci: sata at 01c18000 { - status = "okay"; - }; - - ehci1: usb at 01c1c000 { - status = "okay"; - }; - - ohci1: usb at 01c1c400 { - status = "okay"; - }; - - pinctrl at 01c20800 { - emac_power_pin_a1000: emac_power_pin at 0 { - allwinner,pins = "PH15"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - - led_pins_a1000: led_pins at 0 { - allwinner,pins = "PH10", "PH20"; - allwinner,function = "gpio_out"; - allwinner,drive = ; - allwinner,pull = ; - }; - }; - - ir0: ir at 01c21800 { - pinctrl-names = "default"; - pinctrl-0 = <&ir0_pins_a>; - status = "okay"; - }; - - uart0: serial at 01c28000 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins_a>; - status = "okay"; - }; - - i2c0: i2c at 01c2ac00 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; - status = "okay"; - - axp209: pmic at 34 { - compatible = "x-powers,axp209"; - reg = <0x34>; - interrupts = <0>; - - interrupt-controller; - #interrupt-cells = <1>; - }; - }; - }; - leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -181,12 +84,107 @@ enable-active-high; gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; }; +}; + +&ahci { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_pins_a>; + phy = <&phy1>; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic at 34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + }; +}; + +&ir0 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; +}; + +&mdio { + phy-supply = <®_emac_3v3>; + status = "okay"; + + phy1: ethernet-phy at 1 { + reg = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; - reg_usb1_vbus: usb1-vbus { - status = "okay"; +&pio { + emac_power_pin_a1000: emac_power_pin at 0 { + allwinner,pins = "PH15"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; }; - reg_usb2_vbus: usb2-vbus { - status = "okay"; + led_pins_a1000: led_pins at 0 { + allwinner,pins = "PH10", "PH20"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; }; }; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; -- 2.3.0