[PATCH v2 18/30] ARM: sun6i: colombus: Convert to DT label based syntax

Maxime Ripard
2015-02-11T09:01:17Z

arch/arm/boot/dts/sun6i-a31-colombus.dts | 120 +++++++++++++++----------------
1 file changed, 59 insertions(+), 61 deletions(-)

diff --git a/arch/arm/boot/dts/sun6i-a31-colombus.dts b/arch/arm/boot/dts/sun6i-a31-colombus.dts
index 84630e56acd7..d6e925c381a3 100644
--- a/arch/arm/boot/dts/sun6i-a31-colombus.dts
+++ b/arch/arm/boot/dts/sun6i-a31-colombus.dts
@@ -61,76 +61,74 @@
chosen {
bootargs = "earlyprintk console=ttyS0,115200";
};
+};

- soc at 01c00000 {
- mmc0: mmc at 01c0f000 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>;
- vmmc-supply = <&reg_vcc3v0>;
- bus-width = <4>;
- cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
- cd-inverted;
- status = "okay";
- };
+&ehci1 {
+ status = "okay";
+};

- usbphy: phy at 01c19400 {
- usb2_vbus-supply = <&reg_usb2_vbus>;
- status = "okay";
- };
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "fail";
+};

- ehci1: usb at 01c1b000 {
- status = "okay";
- };
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};

- pio: pinctrl at 01c20800 {
- mmc0_pins_a: mmc0 at 0 {
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};

- mmc0_cd_pin_colombus: mmc0_cd_pin at 0 {
- allwinner,pins = "PA8";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>;
+ vmmc-supply = <&reg_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};

- usb2_vbus_pin_colombus: usb2_vbus_pin at 0 {
- allwinner,pins = "PH24";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
- };
+&mmc0_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};

- uart0: serial at 01c28000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
- };
+&pio {
+ mmc0_cd_pin_colombus: mmc0_cd_pin at 0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };

- i2c0: i2c at 01c2ac00 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "fail";
- };
+ usb2_vbus_pin_colombus: usb2_vbus_pin at 0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};

- i2c1: i2c at 01c2b000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
- };
+&reg_usb2_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_vbus_pin_colombus>;
+ gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};

- i2c2: i2c at 01c2b400 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
- status = "okay";
- };
- };
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};

- reg_usb2_vbus: usb2-vbus {
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_vbus_pin_colombus>;
- gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>;