From: manabian@gmail.com (Joachim Eastwood)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 0/6] Add support for NXP LPC18xx family
Date: Wed, 1 Apr 2015 23:20:37 +0200 [thread overview]
Message-ID: <1427923243-26296-1-git-send-email-manabian@gmail.com> (raw)
This patch set adds minimal support for the LPC18xx/43xx family of
Cortex-M3/4 MCUs from NXP.
Patch set is based on Linus master v4.0-rc6. I assume it's too late
for 4.1 now, so the target for these patches is 4.2.
To keep the amount of dependencies down the PLL1 clock has been hard
coded in the lpc18xx.dtsi file. The clock system of LPC18xx is quite
advanced for a MCU and requires two clk drivers to work. A patch set
with these drivers and update to the dtsi files will be posted
separately.
Drivers for pinctrl, gpio, ethernet, i2c, rtc and emc (external
memories) are also coming for LPC18xx. Right now these can found on:
https://github.com/manabian/linux-lpc
I don't know the policy on new kernel configs, but if this is a no go
the last patch can be dropped.
For zImage support: https://patchwork.kernel.org/patch/5505741/
Sucessfuly tested on Embedded Artist LPC4357 Developers Kit.
Joachim Eastwood (6):
ARM: lpc18xx: add basic support for NXP LPC18xx/43xx SoCs
clocksource: add lpc32xx timer driver
doc: dt: add documentation for lpc3250-timer
ARM: dts: Add base DT for NXP LPC18xx and LPC4357
ARM: dts: Add DT for Embedded Artist LPC4357 Developers Kit
ARM: lpc18xx: add kernel config
.../bindings/timer/nxp,lpc3250-timer.txt | 25 +++
arch/arm/Kconfig | 20 ++
arch/arm/Kconfig.debug | 8 +-
arch/arm/Makefile | 1 +
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/lpc18xx.dtsi | 117 ++++++++++
arch/arm/boot/dts/lpc4357-ea4357.dts | 34 +++
arch/arm/boot/dts/lpc4357.dtsi | 39 ++++
arch/arm/configs/lpc18xx_defconfig | 135 +++++++++++
arch/arm/mach-lpc18xx/Makefile | 1 +
arch/arm/mach-lpc18xx/Makefile.boot | 3 +
arch/arm/mach-lpc18xx/board-dt.c | 24 ++
drivers/clocksource/Kconfig | 10 +
drivers/clocksource/Makefile | 1 +
drivers/clocksource/time-lpc32xx.c | 249 +++++++++++++++++++++
15 files changed, 666 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/timer/nxp,lpc3250-timer.txt
create mode 100644 arch/arm/boot/dts/lpc18xx.dtsi
create mode 100644 arch/arm/boot/dts/lpc4357-ea4357.dts
create mode 100644 arch/arm/boot/dts/lpc4357.dtsi
create mode 100644 arch/arm/configs/lpc18xx_defconfig
create mode 100644 arch/arm/mach-lpc18xx/Makefile
create mode 100644 arch/arm/mach-lpc18xx/Makefile.boot
create mode 100644 arch/arm/mach-lpc18xx/board-dt.c
create mode 100644 drivers/clocksource/time-lpc32xx.c
--
1.8.0
next reply other threads:[~2015-04-01 21:20 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-01 21:20 Joachim Eastwood [this message]
2015-04-01 21:20 ` [PATCH 1/6] ARM: lpc18xx: add basic support for NXP LPC18xx/43xx SoCs Joachim Eastwood
2015-04-02 14:21 ` Arnd Bergmann
2015-04-02 16:48 ` Joachim Eastwood
2015-04-02 22:25 ` Ezequiel Garcia
2015-04-09 20:23 ` Arnd Bergmann
2015-04-01 21:20 ` [PATCH 2/6] clocksource: add lpc32xx timer driver Joachim Eastwood
2015-04-02 14:24 ` Arnd Bergmann
2015-04-02 16:35 ` Joachim Eastwood
2015-04-09 20:24 ` Arnd Bergmann
2015-04-09 20:43 ` Joachim Eastwood
2015-04-01 21:20 ` [PATCH 3/6] doc: dt: add documentation for lpc3250-timer Joachim Eastwood
2015-04-01 21:20 ` [PATCH 4/6] ARM: dts: Add base DT for NXP LPC18xx and LPC4357 Joachim Eastwood
2015-04-02 14:25 ` Arnd Bergmann
2015-04-02 16:36 ` Joachim Eastwood
2015-04-01 21:20 ` [PATCH 5/6] ARM: dts: Add DT for Embedded Artist LPC4357 Developers Kit Joachim Eastwood
2015-04-01 21:20 ` [PATCH 6/6] ARM: lpc18xx: add kernel config Joachim Eastwood
2015-04-02 14:26 ` [PATCH 0/6] Add support for NXP LPC18xx family Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1427923243-26296-1-git-send-email-manabian@gmail.com \
--to=manabian@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).