From: s.hauer@pengutronix.de (Sascha Hauer)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 16/16] ARM64: dts: mt8173: Add thermal/auxadc device nodes
Date: Wed, 20 May 2015 15:20:46 +0200 [thread overview]
Message-ID: <1432128046-12921-17-git-send-email-s.hauer@pengutronix.de> (raw)
In-Reply-To: <1432128046-12921-1-git-send-email-s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index 924fdb6..50d424f 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -147,6 +147,11 @@
(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ auxadc: auxadc at 11001000 {
+ compatible = "mediatek,mt8173-auxadc";
+ reg = <0 0x11001000 0 0x1000>;
+ };
+
uart0: serial at 11002000 {
compatible = "mediatek,mt8173-uart",
"mediatek,mt6577-uart";
@@ -182,6 +187,19 @@
clocks = <&uart_clk>;
status = "disabled";
};
+
+ thermal: thermal at 1100b000 {
+ #thermal-sensor-cells = <1>;
+ compatible = "mediatek,mt8173-thermal";
+ reg = <0 0x1100b000 0 0x1000>;
+ interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
+ clock-names = "therm", "auxadc";
+ resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
+ reset-names = "therm";
+ auxadc = <&auxadc>;
+ apmixedsys = <&apmixedsys>;
+ };
};
};
--
2.1.4
next prev parent reply other threads:[~2015-05-20 13:20 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-20 13:20 [PATCH v4] Thermal cleanups and hardware trip points Sascha Hauer
2015-05-20 13:20 ` [PATCH 01/16] thermal: consistently use int for temperatures Sascha Hauer
2015-05-20 13:20 ` [PATCH 02/16] thermal: trivial: fix typo in comment Sascha Hauer
2015-05-20 13:20 ` [PATCH 03/16] thermal: remove useless call to thermal_zone_device_set_polling Sascha Hauer
2015-05-20 13:20 ` [PATCH 04/16] thermal: Use IS_ENABLED instead of #ifdef Sascha Hauer
2015-05-20 13:20 ` [PATCH 05/16] thermal: Add comment explaining test for critical temperature Sascha Hauer
2015-05-20 13:20 ` [PATCH 06/16] thermal: inline only once used function Sascha Hauer
2015-05-20 13:20 ` [PATCH 07/16] thermal: streamline get_trend callbacks Sascha Hauer
2015-05-20 13:20 ` [PATCH 08/16] thermal: Allow sensor ops to fail with -ENOSYS Sascha Hauer
2015-05-20 13:20 ` [PATCH 09/16] thermal: of: always set sensor related callbacks Sascha Hauer
2015-05-20 13:20 ` [PATCH 10/16] thermal: Make struct thermal_zone_device_ops const Sascha Hauer
2015-05-20 13:20 ` [PATCH 11/16] thermal: bang-bang governor: act on lower trip boundary Sascha Hauer
2015-05-20 13:20 ` [PATCH 12/16] thermal: thermal: Add support for hardware-tracked trip points Sascha Hauer
2015-05-20 13:20 ` [PATCH 13/16] thermal: of: implement .set_trips for device tree thermal zones Sascha Hauer
2015-05-20 13:20 ` [PATCH 14/16] dt-bindings: thermal: Add binding document for Mediatek thermal controller Sascha Hauer
2015-05-20 13:20 ` [PATCH 15/16] thermal: Add Mediatek thermal controller support Sascha Hauer
2015-05-20 13:20 ` Sascha Hauer [this message]
2015-06-08 6:56 ` [PATCH v4] Thermal cleanups and hardware trip points Sascha Hauer
2015-06-22 6:38 ` Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1432128046-12921-17-git-send-email-s.hauer@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).