linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: tharvey@gateworks.com (Tim Harvey)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 0/2] imx6: Implement external watchdog reset
Date: Thu, 28 May 2015 15:54:35 -0700	[thread overview]
Message-ID: <1432853677-5150-1-git-send-email-tharvey@gateworks.com> (raw)

The IMX6 watchdog supports assertion of a signal (WDOG_B) which
can be pinmux'd to an external pin. This is typically used for boards that
have PMIC's in control of the IMX6 power rails. In fact, failure to use
such an external reset on boards with external PMIC's can result in various
hangs due to the IMX6 not being fully reset [1] as well as the board failing
to reset because its PMIC has not been reset to provide adequate voltate for
the CPU when comming out of reset at 800Mhz when it was at 400Mhz prior to
reset.
 
This adds a new device-tree property 'ext-reset' to fsl-imx-wdt in order to
indicate the board has such a reset and to cause the watchdog to be
configured to assert WDOG_B instead of an internal reset both on a
watchdog timeout and in system_restart.
 
The second patch adds the watchdog configuration and pinmux for Gateworks
Ventana boards.

I would expect that maintainers of other IMX6 boards that use PMIC's that
are resettable via WDOG_B to follow-up with similar device-tree patches.
I've attempted to Cc those individuals here.
 
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/333689.html

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Iain Paton <ipaton0@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>

Tim Harvey (2):
  watchdog: imx2_wdt: add external reset support via 'ext-reset' dt
    property
  ARM: dts: ventana: Add ext-reset support

 .../devicetree/bindings/watchdog/fsl-imx-wdt.txt       |  2 ++
 arch/arm/boot/dts/imx6qdl-gw51xx.dtsi                  | 13 +++++++++++++
 arch/arm/boot/dts/imx6qdl-gw52xx.dtsi                  | 13 +++++++++++++
 arch/arm/boot/dts/imx6qdl-gw53xx.dtsi                  | 13 +++++++++++++
 arch/arm/boot/dts/imx6qdl-gw54xx.dtsi                  | 18 ++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-gw551x.dtsi                  | 12 ++++++++++++
 arch/arm/boot/dts/imx6qdl-gw552x.dtsi                  | 13 +++++++++++++
 drivers/watchdog/imx2_wdt.c                            | 18 ++++++++++++++++--
 8 files changed, 100 insertions(+), 2 deletions(-)

-- 
1.9.1

             reply	other threads:[~2015-05-28 22:54 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-05-28 22:54 Tim Harvey [this message]
2015-05-28 22:54 ` [PATCH 1/2] watchdog: imx2_wdt: add external reset support via 'ext-reset' dt property Tim Harvey
2015-05-29 16:37   ` Lucas Stach
2015-05-28 22:54 ` [PATCH 2/2] ARM: dts: ventana: Add ext-reset support Tim Harvey
2015-05-29  6:17   ` Markus Pargmann
2015-05-29 14:01     ` Tim Harvey
2015-06-04 20:15 ` [PATCH v2 0/2] imx6: Implement external watchdog reset Tim Harvey
2015-06-04 20:15   ` [PATCH v2 1/2] watchdog: imx2_wdt: add external reset support via 'ext-reset-output' dt prop Tim Harvey
2015-06-05 16:38     ` Zhi Li
2015-06-25 23:22       ` Tim Harvey
2015-06-22  9:22     ` Lucas Stach
2015-06-28 15:07     ` Shawn Guo
2015-06-29  1:17     ` Shawn Guo
2015-07-02 16:49       ` Tim Harvey
2015-07-03  1:02         ` Shawn Guo
2015-07-28 15:27     ` [PATCH v3 0/2] imx6: Implement external watchdog reset Tim Harvey
2015-07-28 15:27       ` [PATCH v3 1/2] watchdog: imx2_wdt: add external reset support via 'ext-reset-output' dt prop Tim Harvey
2015-08-05 13:01         ` Shawn Guo
2015-10-13 14:11         ` Tim Harvey
2015-07-28 15:27       ` [PATCH v3 2/2] ARM: dts: ventana: Add ext-reset support Tim Harvey
2015-10-30 17:00       ` [PATCH v3 0/2] imx6: Implement external watchdog reset Akshay Bhat
2015-10-30 17:31         ` Tim Harvey
2015-06-04 20:16   ` [PATCH v2 2/2] ARM: dts: ventana: Add ext-reset support Tim Harvey

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1432853677-5150-1-git-send-email-tharvey@gateworks.com \
    --to=tharvey@gateworks.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).