From: ivan.ivanov@linaro.org (Ivan T. Ivanov)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/7] arm64: dts: qcom: Add msm8916 BLSP device nodes
Date: Thu, 4 Jun 2015 12:19:01 +0300 [thread overview]
Message-ID: <1433409546-23995-3-git-send-email-ivan.ivanov@linaro.org> (raw)
In-Reply-To: <1433409546-23995-1-git-send-email-ivan.ivanov@linaro.org>
Add device nodes for SPI1, SPI2, SPI3, I2C4, SPI5, SPI6 and
BAM(DMA) engine connected to them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8916.dtsi | 128 ++++++++++++++++++++++++++++++++++
1 file changed, 128 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 9ab9a92..6681c65 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -108,6 +108,134 @@
status = "disabled";
};
+ blsp_dma: dma at 7884000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07884000 0x23000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi1: spi at 78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 5>, <&blsp_dma 4>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi1_default>;
+ pinctrl-1 = <&spi1_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi2: spi at 78b6000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 7>, <&blsp_dma 6>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi2_default>;
+ pinctrl-1 = <&spi2_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi3: spi at 78b7000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 9>, <&blsp_dma 8>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi3_default>;
+ pinctrl-1 = <&spi3_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi4: spi at 78b8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 11>, <&blsp_dma 10>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi4_default>;
+ pinctrl-1 = <&spi4_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi5: spi at 78b9000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 13>, <&blsp_dma 12>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi5_default>;
+ pinctrl-1 = <&spi5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi6: spi at 78ba000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078ba000 0x600>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 15>, <&blsp_dma 14>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi6_default>;
+ pinctrl-1 = <&spi6_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c4: i2c at 78b8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x78b8000 0x1000>;
+ interrupts = <GIC_SPI 98 0>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c4_default>;
+ pinctrl-1 = <&i2c4_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
intc: interrupt-controller at b000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
--
1.9.1
next prev parent reply other threads:[~2015-06-04 9:19 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-04 9:18 [PATCH 0/7] arm64: dts: qcom: msm8916 fixes and updates Ivan T. Ivanov
2015-06-04 9:19 ` [PATCH 1/7] arm64: dts: qcom: Extend msm8916 pinctrl device coverage Ivan T. Ivanov
2015-06-04 9:19 ` Ivan T. Ivanov [this message]
2015-06-04 9:19 ` [PATCH 3/7] arm64: dts: qcom: Add msm8916 sdhci configuration nodes Ivan T. Ivanov
2015-06-04 9:19 ` [PATCH 4/7] arm64: dts: qcom: Add msm8916 USB " Ivan T. Ivanov
2015-06-04 9:19 ` [PATCH 5/7] arm64: dts: qcom: apq8016-sbc: Don't hog client driver pins Ivan T. Ivanov
2015-06-04 9:19 ` [PATCH 6/7] arm64: dts: qcom: Fix apq8016-sbc board USB related pin definitions Ivan T. Ivanov
2015-06-04 9:19 ` [PATCH 7/7] arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes Ivan T. Ivanov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1433409546-23995-3-git-send-email-ivan.ivanov@linaro.org \
--to=ivan.ivanov@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).