From: hdegoede@redhat.com (Hans de Goede)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v5 4/7] phy-sun4i-usb: Add support for the usb-phys on the sun8i-a23 SoC
Date: Sat, 13 Jun 2015 14:37:48 +0200 [thread overview]
Message-ID: <1434199071-22127-5-git-send-email-hdegoede@redhat.com> (raw)
In-Reply-To: <1434199071-22127-1-git-send-email-hdegoede@redhat.com>
The usb-phys on the sun8i-a23 SoC have the same setup wrt clocks as on the
sun6i-a31 SoC, but there are only 2 instead of 3 like on the sun5i-a13 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt | 2 ++
drivers/phy/phy-sun4i-usb.c | 7 +++++--
2 files changed, 7 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
index 557fa99..f0c640a 100644
--- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
@@ -7,6 +7,7 @@ Required properties:
* allwinner,sun5i-a13-usb-phy
* allwinner,sun6i-a31-usb-phy
* allwinner,sun7i-a20-usb-phy
+ * allwinner,sun8i-a23-usb-phy
- reg : a list of offset + length pairs
- reg-names :
* "phy_ctrl"
@@ -17,6 +18,7 @@ Required properties:
- clock-names :
* "usb_phy" for sun4i, sun5i or sun7i
* "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i
+ * "usb0_phy", "usb1_phy" for sun8i
- resets : a list of phandle + reset specifier pairs
- reset-names :
* "usb0_reset"
diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-usb.c
index d78a071..6850fcd 100644
--- a/drivers/phy/phy-sun4i-usb.c
+++ b/drivers/phy/phy-sun4i-usb.c
@@ -442,7 +442,8 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
INIT_DELAYED_WORK(&data->detect, sun4i_usb_phy0_id_vbus_det_scan);
dev_set_drvdata(dev, data);
- if (of_device_is_compatible(np, "allwinner,sun5i-a13-usb-phy"))
+ if (of_device_is_compatible(np, "allwinner,sun5i-a13-usb-phy") ||
+ of_device_is_compatible(np, "allwinner,sun8i-a23-usb-phy"))
data->num_phys = 2;
else
data->num_phys = 3;
@@ -453,7 +454,8 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
else
data->disc_thresh = 3;
- if (of_device_is_compatible(np, "allwinner,sun6i-a31-usb-phy"))
+ if (of_device_is_compatible(np, "allwinner,sun6i-a31-usb-phy") ||
+ of_device_is_compatible(np, "allwinner,sun8i-a23-usb-phy"))
dedicated_clocks = true;
else
dedicated_clocks = false;
@@ -588,6 +590,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
{ .compatible = "allwinner,sun5i-a13-usb-phy" },
{ .compatible = "allwinner,sun6i-a31-usb-phy" },
{ .compatible = "allwinner,sun7i-a20-usb-phy" },
+ { .compatible = "allwinner,sun8i-a23-usb-phy" },
{ },
};
MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);
--
2.4.3
next prev parent reply other threads:[~2015-06-13 12:37 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-13 12:37 [PATCH v5 0/7] phy-sun4i-usb: Add OTG and newer SoC support Hans de Goede
2015-06-13 12:37 ` [PATCH v5 1/7] phy-sun4i-usb: Add id and vbus detection support for the otg phy (phy0) Hans de Goede
2015-06-13 12:37 ` [PATCH v5 2/7] phy-sun4i-usb: Add extcon " Hans de Goede
2015-06-15 0:39 ` Chanwoo Choi
2015-07-31 14:23 ` [linux-sunxi] " Jonathan Liu
2015-07-31 14:24 ` Hans de Goede
2015-06-13 12:37 ` [PATCH v5 3/7] phy-sun4i-usb: Swap check for disconnect threshold Hans de Goede
2015-06-13 12:37 ` Hans de Goede [this message]
2015-06-13 12:37 ` [PATCH v5 5/7] phy-sun4i-usb: Add support for the usb-phys on the sun8i-a33 SoC Hans de Goede
2015-06-13 12:37 ` [PATCH v5 6/7] phy-sun4i-usb: Add support for boards with broken Vusb-detection Hans de Goede
2015-06-13 12:37 ` [PATCH v5 7/7] phy-sun4i-usb: Add support for monitoring vbus via a power-supply Hans de Goede
2015-06-15 5:27 ` [PATCH v5 0/7] phy-sun4i-usb: Add OTG and newer SoC support Kishon Vijay Abraham I
2015-07-15 11:07 ` Kishon Vijay Abraham I
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1434199071-22127-5-git-send-email-hdegoede@redhat.com \
--to=hdegoede@redhat.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).