* [PATCH v3 1/3] ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay
2015-09-26 22:01 [PATCH v3 0/3] Add support for the Armada-370-based Seagate NAS Simon Guinot
@ 2015-09-26 22:01 ` Simon Guinot
2015-09-26 22:01 ` [PATCH v3 2/3] ARM: mvebu: add DT support for Seagate Personal Cloud Simon Guinot
2015-09-26 22:01 ` [PATCH v3 3/3] ARM: mvebu: enable options for Seagate NAS in mvebu_v7_defconfig Simon Guinot
2 siblings, 0 replies; 4+ messages in thread
From: Simon Guinot @ 2015-09-26 22:01 UTC (permalink / raw)
To: linux-arm-kernel
From: Vincent Donnefort <vdonnefort@gmail.com>
This patch adds DT support for the Seagate NAS 2 and 4-Bay.
Here are some information allowing to identify these devices:
Product name | Seagate NAS 2-Bay | Seagate NAS 4-Bay
Code name (board/PCB) | Dart 2-Bay | Dart 4-Bay
Model name (case sticker) | SRPD20 | SRPD40
Material desc (product spec) | STCTxxxxxxx | STCUxxxxxxx
Chipset list (common):
- SoC Marvell Armada 370 88F6707, CPU @1.2GHz
- SDRAM memory: 512MB DDR3 600MHz (16-bits bandwidth)
- NAND flash 256MB, 8-bits (Micron MT29F2G08AAB or Hinyx H27U2G8F2CTR-BC)
- 2 SATA II ports (SoC)
- 1 Ethernet Gigabit ports (PHY Marvell 88E1518)
- 2 USB3 host ports (PCIe controller ASM1042)
- GPIO fan (4 speeds)
- External I2C RTC (MCP7940NT)
- 3 push buttons (power, backup and reset)
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
Only on 4-Bay models:
- 2 extra SATA III ports (PCIe AHCI controller Marvell 88SE9170)
- 1 extra Ethernet Gigabit ports (PHY Marvell 88E1518)
- I2C GPIO expander (PCA9554A)
- 2 extra SATA LEDs (bi-color, blue and red)
Note that support for the white SATA LEDs associated with HDDs 0 and 1
is missing. A dedicated LED driver is needed.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts | 36 ++++
arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts | 133 ++++++++++++
arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi | 231 +++++++++++++++++++++
4 files changed, 402 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts
create mode 100644 arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts
create mode 100644 arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
Changes for v2:
- Rename DTS files using the products names.
- Update model and compatible properties as well.
- Add some information allowing to identify the devices in the commit
message and in the DTS files headers.
- Remove duplicated rtc alias in armada-370-seagate-nas-xbay.dtsi.
Changes for v3:
- Use GPIO_ACTIVE_HIGH instead of 0 in gpios property (gpio-fan node).
- Add Andrew's Acked-by.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1c5f22525a8b..a0cc0b63db41 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -710,6 +710,8 @@ dtb-$(CONFIG_MACH_ARMADA_370) += \
armada-370-netgear-rn102.dtb \
armada-370-netgear-rn104.dtb \
armada-370-rd.dtb \
+ armada-370-seagate-nas-2bay.dtb \
+ armada-370-seagate-nas-4bay.dtb \
armada-370-synology-ds213j.dtb
dtb-$(CONFIG_MACH_ARMADA_375) += \
armada-375-db.dtb
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts b/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts
new file mode 100644
index 000000000000..43dd69a54ff1
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts
@@ -0,0 +1,36 @@
+/*
+ * Device Tree file for Seagate NAS 2-Bay (Armada 370 SoC).
+ *
+ * Copyright (C) 2015 Seagate
+ *
+ * Author: Vincent Donnefort <vdonnefort@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * Here are some information allowing to identify the device:
+ *
+ * Product name : Seagate NAS 2-Bay
+ * Code name (board/PCB) : Dart 2-Bay
+ * Model name (case sticker) : SRPD20
+ * Material desc (product spec) : STCTxxxxxxx
+ */
+
+/dts-v1/;
+#include "armada-370-seagate-nas-xbay.dtsi"
+
+/ {
+ model = "Seagate NAS 2-Bay (Dart, SRPD20)";
+ compatible = "seagate,dart-2", "marvell,armada370", "marvell,armada-370-xp";
+
+ gpio-fan {
+ gpio-fan,speed-map =
+ < 0 3
+ 950 2
+ 1400 1
+ 1800 0>;
+ };
+};
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts b/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts
new file mode 100644
index 000000000000..bc3e6a3a233b
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts
@@ -0,0 +1,133 @@
+/*
+ * Device Tree file for Seagate NAS 4-Bay (Armada 370 SoC).
+ *
+ * Copyright (C) 2015 Seagate
+ *
+ * Author: Vincent Donnefort <vdonnefort@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * Here are some information allowing to identify the device:
+ *
+ * Product name : Seagate NAS 4-Bay
+ * Code name (board/PCB) : Dart 4-Bay
+ * Model name (case sticker) : SRPD40
+ * Material desc (product spec) : STCUxxxxxxx
+ */
+
+/dts-v1/;
+#include "armada-370-seagate-nas-xbay.dtsi"
+#include <dt-bindings/leds/leds-ns2.h>
+
+/ {
+ model = "Seagate NAS 4-Bay (Dart, SRPD40)";
+ compatible = "seagate,dart-4", "marvell,armada370", "marvell,armada-370-xp";
+
+ soc {
+ pcie-controller {
+ /* SATA AHCI controller 88SE9170 */
+ pcie at 1,0 {
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ mdio {
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+ };
+
+ ethernet at 74000 {
+ status = "okay";
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ i2c at 11000 {
+ /* I2C GPIO expander (PCA9554A) */
+ pca9554: pca9554 at 21 {
+ compatible = "nxp,pca9554";
+ reg = <0x21>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+ };
+ };
+
+ regulators {
+ regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "SATA2 power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pca9554 6 GPIO_ACTIVE_HIGH>;
+ };
+ regulator at 4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "SATA3 power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&pca9554 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ red-sata2 {
+ label = "dart:red:sata2";
+ gpios = <&pca9554 0 GPIO_ACTIVE_LOW>;
+ };
+ red-sata3 {
+ label = "dart:red:sata3";
+ gpios = <&pca9554 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds-ns2 {
+ compatible = "lacie,ns2-leds";
+
+ white-sata2 {
+ label = "dart:white:sata2";
+ cmd-gpio = <&pca9554 1 GPIO_ACTIVE_HIGH>;
+ slow-gpio = <&pca9554 2 GPIO_ACTIVE_HIGH>;
+ num-modes = <4>;
+ modes-map = <NS_V2_LED_SATA 0 0
+ NS_V2_LED_OFF 0 1
+ NS_V2_LED_ON 1 0
+ NS_V2_LED_ON 1 1>;
+ };
+ white-sata3 {
+ label = "dart:white:sata3";
+ cmd-gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>;
+ slow-gpio = <&pca9554 5 GPIO_ACTIVE_HIGH>;
+ num-modes = <4>;
+ modes-map = <NS_V2_LED_SATA 0 0
+ NS_V2_LED_OFF 0 1
+ NS_V2_LED_ON 1 0
+ NS_V2_LED_ON 1 1>;
+ };
+ };
+
+ gpio-fan {
+ gpio-fan,speed-map =
+ < 0 3
+ 800 2
+ 1050 1
+ 1300 0>;
+ };
+};
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
new file mode 100644
index 000000000000..3036e25c5992
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
@@ -0,0 +1,231 @@
+/*
+ * Device Tree common file for the Seagate NAS 2 and 4-bay (Armada 370 SoC).
+ *
+ * Copyright (C) 2015 Seagate
+ *
+ * Author: Vincent Donnefort <vdonnefort@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * TODO: add support for the white SATA LEDs associated with HDD 0 and 1.
+ */
+
+#include "armada-370.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /* USB 3.0 bridge ASM1042A */
+ pcie at 2,0 {
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+ };
+
+ ethernet at 70000 {
+ status = "okay";
+ pinctrl-0 = <&ge0_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ i2c at 11000 {
+ status = "okay";
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ clock-frequency = <100000>;
+
+ /* RTC - NXP 8563T (second source) */
+ rtc at 51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ interrupts = <110>;
+ };
+ /* RTC - MCP7940NT */
+ rtc at 6f {
+ compatible = "microchip,mcp7941x";
+ reg = <0x6f>;
+ interrupts = <110>;
+ };
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x300000>;
+ };
+ partition at 300000 {
+ label = "device-tree";
+ reg = <0x300000 0x20000>;
+ };
+ partition at 320000 {
+ label = "linux";
+ reg = <0x320000 0x2000000>;
+ };
+ partition at 2320000 {
+ label = "rootfs";
+ reg = <0x2320000 0xdce0000>;
+ };
+ };
+ };
+
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+
+ regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA0 power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+ };
+ regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio2 0 GPIO_ACTIVE_HIGH
+ &gpio2 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button at 1 {
+ label = "Power button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ button at 2 {
+ label = "Backup button";
+ linux,code = <KEY_OPTION>;
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ button at 3 {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ white-power {
+ label = "dart:white:power";
+ gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "timer";
+
+ };
+ red-power {
+ label = "dart:red:power";
+ gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ };
+ red-sata0 {
+ label = "dart:red:sata0";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ red-sata1 {
+ label = "dart:red:sata1";
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <&hdd0_led_sata_pin>, <&hdd1_led_sata_pin>;
+ pinctrl-names = "default";
+
+ hdd0_led_sata_pin: hdd0-led-sata-pin {
+ marvell,pins = "mpp48";
+ marvell,function = "sata1";
+ };
+ hdd0_led_gpio_pin: hdd0-led-gpio-pin {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ hdd1_led_sata_pin: hdd1-led-sata-pin {
+ marvell,pins = "mpp57";
+ marvell,function = "sata0";
+ };
+ hdd1_led_gpio_pin: hdd1-led-gpio-pin {
+ marvell,pins = "mpp57";
+ marvell,function = "gpio";
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v3 2/3] ARM: mvebu: add DT support for Seagate Personal Cloud
2015-09-26 22:01 [PATCH v3 0/3] Add support for the Armada-370-based Seagate NAS Simon Guinot
2015-09-26 22:01 ` [PATCH v3 1/3] ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay Simon Guinot
@ 2015-09-26 22:01 ` Simon Guinot
2015-09-26 22:01 ` [PATCH v3 3/3] ARM: mvebu: enable options for Seagate NAS in mvebu_v7_defconfig Simon Guinot
2 siblings, 0 replies; 4+ messages in thread
From: Simon Guinot @ 2015-09-26 22:01 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds DT support for the Seagate Personal Cloud 1 and 2-Bay.
Here are some information allowing to identify these devices:
Product name | Personal Cloud | Personal Cloud 2-Bay
Code name (board/PCB) | Cumulus | Cumulus Max
Model name (case sticker) | SRN21C | SRN22C
Material desc (product spec) | STCRxxxxxxx | STCSxxxxxxx
Chipset list:
- SoC Marvell Armada 370 88F6707, CPU @1GHz
- SDRAM memory: 512MB DDR3 667MHz (16-bits bandwidth)
- SPI flash 1MB (Macronix MX25L8006E)
- 1 or 2 SATA internal ports
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- 1 USB3 host port (PCIe controller ASM1042)
- 1 USB2 host port (SoC)
- 2 push buttons (power and reset)
- 1 SATA LED (bi-color, white and red)
Note that support for the white SATA LED is missing. A dedicated LED
driver is needed.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/Makefile | 2 +
.../dts/armada-370-seagate-personal-cloud-2bay.dts | 51 ++++++
.../boot/dts/armada-370-seagate-personal-cloud.dts | 37 +++++
.../dts/armada-370-seagate-personal-cloud.dtsi | 174 +++++++++++++++++++++
4 files changed, 264 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts
create mode 100644 arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts
create mode 100644 arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
Changes for v2:
- Rename DTS files using the products names.
- Update model and compatible properties as well.
- Add some information allowing to identify the devices in the commit
message and in the DTS files headers.
Changes for v3:
- Fix spelling for Personal Cloud DTS files: 'personal' instead of
'personnal'.
- Add Andrew's Acked-by.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a0cc0b63db41..8e83da127a9c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -712,6 +712,8 @@ dtb-$(CONFIG_MACH_ARMADA_370) += \
armada-370-rd.dtb \
armada-370-seagate-nas-2bay.dtb \
armada-370-seagate-nas-4bay.dtb \
+ armada-370-seagate-personal-cloud.dtb \
+ armada-370-seagate-personal-cloud-2bay.dtb \
armada-370-synology-ds213j.dtb
dtb-$(CONFIG_MACH_ARMADA_375) += \
armada-375-db.dtb
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts b/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts
new file mode 100644
index 000000000000..fe7a70ecb7bd
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts
@@ -0,0 +1,51 @@
+/*
+ * Device Tree file for Seagate Personal Cloud NAS 2-Bay (Armada 370 SoC).
+ *
+ * Copyright (C) 2015 Seagate
+ *
+ * Author: Simon Guinot <simon.guinot@sequanux.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * Here are some information allowing to identify the device:
+ *
+ * Product name : Seagate Personal Cloud 2-Bay
+ * Code name (board/PCB) : Cumulus Max
+ * Model name (case sticker) : SRN22C
+ * Material desc (product spec) : STCSxxxxxxx
+ */
+
+/dts-v1/;
+#include "armada-370-seagate-personal-cloud.dtsi"
+
+/ {
+ model = "Seagate Personal Cloud 2-Bay (Cumulus, SRN22C)";
+ compatible = "seagate,cumulus-max", "marvell,armada370", "marvell,armada-370-xp";
+
+ soc {
+ internal-regs {
+ sata at a0000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+ };
+ };
+
+ regulators {
+ regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts
new file mode 100644
index 000000000000..1bcd6ac7f051
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts
@@ -0,0 +1,37 @@
+/*
+ * Device Tree file for Seagate Personal Cloud NAS (Armada 370 SoC).
+ *
+ * Copyright (C) 2015 Seagate
+ *
+ * Author: Simon Guinot <simon.guinot@sequanux.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * Here are some information allowing to identify the device:
+ *
+ * Product name : Seagate Personal Cloud
+ * Code name (board/PCB) : Cumulus
+ * Model name (case sticker) : SRN21C
+ * Material desc (product spec) : STCRxxxxxxx
+ */
+
+/dts-v1/;
+#include "armada-370-seagate-personal-cloud.dtsi"
+
+/ {
+ model = "Seagate Personal Cloud (Cumulus, SRN21C)";
+ compatible = "seagate,cumulus", "marvell,armada370", "marvell,armada-370-xp";
+
+ soc {
+ internal-regs {
+ sata at a0000 {
+ status = "okay";
+ nr-ports = <1>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
new file mode 100644
index 000000000000..798f2be968e2
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
@@ -0,0 +1,174 @@
+/*
+ * Device Tree common file for the Seagate Personal Cloud NAS 1 and 2-Bay
+ * (Armada 370 SoC).
+ *
+ * Copyright (C) 2015 Seagate
+ *
+ * Author: Simon Guinot <simon.guinot@sequanux.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/*
+ * TODO: add support for the white SATA LED.
+ */
+
+#include "armada-370.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /* USB 3.0 Bridge ASM1042A */
+ pcie at 1,0 {
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+
+ mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+ };
+
+ ethernet at 74000 {
+ status = "okay";
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ spi at 10600 {
+ status = "okay";
+ pinctrl-0 = <&spi0_pins2>;
+ pinctrl-names = "default";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* MX25L8006E */
+ compatible = "mxicy,mx25l8005", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x100000>;
+ };
+ };
+ };
+
+ usb at 50000 {
+ status = "okay";
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ };
+ regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA0 power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button at 1 {
+ label = "Power button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <100>;
+ };
+ button at 2 {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ button at 3 {
+ label = "USB VBUS error";
+ linux,code = <KEY_UNKNOWN>;
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ debounce-interval = <100>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ red-sata0 {
+ label = "cumulus:red:sata0";
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <&sata_led_pin>;
+ pinctrl-names = "default";
+
+ sata_led_pin: sata-led-pin {
+ marvell,pins = "mpp60";
+ marvell,function = "sata0";
+ };
+ gpio_led_pin: gpio-led-pin {
+ marvell,pins = "mpp60";
+ marvell,function = "gpio";
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 4+ messages in thread