[PATCH 0/5] mt8173 spi multiple devices support

[PATCH 0/5] mt8173 spi multiple devices support

[Leilk Liu]

This series are based on 4.3-rc1 and provide 5 patches to support
mt8173 spi multiple devices.

Change in this series:
1. update document to add cs-gpio;
2. remove mtk_spi_config function;
3. move controller_data to master->setup;
4. add mt8173 spi multiple devices support;
5. update dts to add cs-gpio and modify cs pin to gpio function.

Leilk Liu (5):
  dt-binding: spi: Mediatek: Update document devicetree bindings to
    support multiple devices
  spi: mediatek: remove mtk_spi_config
  spi: mediatek: handle controller_data in mtk_spi_setup
  spi: mediatek: mt8173 spi multiple devices support
  arm64: dts: spi bus dts support multiple devices

 .../devicetree/bindings/spi/spi-mt65xx.txt         |   8 +-
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts        |   3 +-
 drivers/spi/spi-mt65xx.c                           | 129 +++++++++++++--------
 3 files changed, 91 insertions(+), 49 deletions(-)
 mode change 100755 => 100644 drivers/spi/spi-mt65xx.c

--
1.8.1.1.dirty

[PATCH 1/5] dt-binding: spi: Mediatek: Update document devicetree bindings to support multiple devices

[Leilk Liu]

This patch update document devicetree bindings to
support multiple devices.

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
---
 Documentation/devicetree/bindings/spi/spi-mt65xx.txt | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt
index dcefc43..8391193 100644
--- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt
+++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt
@@ -28,8 +28,11 @@ Required properties:
   "parent-clk" for the parent clock.
 
 Optional properties:
+-cs-gpios: see spi-bus.txt, only required for MT8173.
+
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
-  controller used, this value should be 0~3, only required for MT8173.
+  controller used. This is a array, the element value should be 0~3,
+  only required for MT8173.
     0: specify GPIO69,70,71,72 for spi pins.
     1: specify GPIO102,103,104,105 for spi pins.
     2: specify GPIO128,129,130,131 for spi pins.
@@ -46,6 +49,7 @@ spi: spi at 1100a000 {
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
 	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
 	clock-names = "spi-clk", "parent-clk";
-	mediatek,pad-select = <0>;
+	cs-gpios = <&pio 105 GPIO_ACTIVE_LOW>, <&pio 72 GPIO_ACTIVE_LOW>;
+	mediatek,pad-select = <1>, <0>;
 	status = "disabled";
 };
-- 
1.8.1.1.dirty

[PATCH 2/5] spi: mediatek: remove mtk_spi_config

[Leilk Liu]

mtk_spi_config() and mtk_spi_prepare_message() both initialize
spi register, so remove mtk_spi_config() and init all register
in mtk_spi_prepare_message().

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
---
 drivers/spi/spi-mt65xx.c | 59 +++++++++++++++++++++---------------------------
 1 file changed, 26 insertions(+), 33 deletions(-)

diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c
index ecb6c58..7bd84c8 100755
--- a/drivers/spi/spi-mt65xx.c
+++ b/drivers/spi/spi-mt65xx.c
@@ -131,10 +131,34 @@ static void mtk_spi_reset(struct mtk_spi *mdata)
 	writel(reg_val, mdata->base + SPI_CMD_REG);
 }
 
-static void mtk_spi_config(struct mtk_spi *mdata,
-			   struct mtk_chip_config *chip_config)
+static int mtk_spi_prepare_message(struct spi_master *master,
+				   struct spi_message *msg)
 {
+	u16 cpha, cpol;
 	u32 reg_val;
+	struct mtk_chip_config *chip_config;
+	struct spi_device *spi = msg->spi;
+	struct mtk_spi *mdata = spi_master_get_devdata(master);
+
+	cpha = spi->mode & SPI_CPHA ? 1 : 0;
+	cpol = spi->mode & SPI_CPOL ? 1 : 0;
+
+	chip_config = spi->controller_data;
+	if (!chip_config) {
+		chip_config = (void *)&mtk_default_chip_info;
+		spi->controller_data = chip_config;
+	}
+
+	reg_val = readl(mdata->base + SPI_CMD_REG);
+	if (cpha)
+		reg_val |= SPI_CMD_CPHA;
+	else
+		reg_val &= ~SPI_CMD_CPHA;
+	if (cpol)
+		reg_val |= SPI_CMD_CPOL;
+	else
+		reg_val &= ~SPI_CMD_CPOL;
+	writel(reg_val, mdata->base + SPI_CMD_REG);
 
 	reg_val = readl(mdata->base + SPI_CMD_REG);
 
@@ -171,37 +195,6 @@ static void mtk_spi_config(struct mtk_spi *mdata,
 	/* pad select */
 	if (mdata->dev_comp->need_pad_sel)
 		writel(mdata->pad_sel, mdata->base + SPI_PAD_SEL_REG);
-}
-
-static int mtk_spi_prepare_message(struct spi_master *master,
-				   struct spi_message *msg)
-{
-	u32 reg_val;
-	u8 cpha, cpol;
-	struct mtk_chip_config *chip_config;
-	struct spi_device *spi = msg->spi;
-	struct mtk_spi *mdata = spi_master_get_devdata(master);
-
-	cpha = spi->mode & SPI_CPHA ? 1 : 0;
-	cpol = spi->mode & SPI_CPOL ? 1 : 0;
-
-	reg_val = readl(mdata->base + SPI_CMD_REG);
-	if (cpha)
-		reg_val |= SPI_CMD_CPHA;
-	else
-		reg_val &= ~SPI_CMD_CPHA;
-	if (cpol)
-		reg_val |= SPI_CMD_CPOL;
-	else
-		reg_val &= ~SPI_CMD_CPOL;
-	writel(reg_val, mdata->base + SPI_CMD_REG);
-
-	chip_config = spi->controller_data;
-	if (!chip_config) {
-		chip_config = (void *)&mtk_default_chip_info;
-		spi->controller_data = chip_config;
-	}
-	mtk_spi_config(mdata, chip_config);
 
 	return 0;
 }
-- 
1.8.1.1.dirty

[PATCH 3/5] spi: mediatek: handle controller_data in mtk_spi_setup

[Leilk Liu]

controller_data is related with device, so move to master->setup
function.

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
---
 drivers/spi/spi-mt65xx.c | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c
index 7bd84c8..406695a 100755
--- a/drivers/spi/spi-mt65xx.c
+++ b/drivers/spi/spi-mt65xx.c
@@ -136,19 +136,13 @@ static int mtk_spi_prepare_message(struct spi_master *master,
 {
 	u16 cpha, cpol;
 	u32 reg_val;
-	struct mtk_chip_config *chip_config;
 	struct spi_device *spi = msg->spi;
+	struct mtk_chip_config *chip_config = spi->controller_data;
 	struct mtk_spi *mdata = spi_master_get_devdata(master);
 
 	cpha = spi->mode & SPI_CPHA ? 1 : 0;
 	cpol = spi->mode & SPI_CPOL ? 1 : 0;
 
-	chip_config = spi->controller_data;
-	if (!chip_config) {
-		chip_config = (void *)&mtk_default_chip_info;
-		spi->controller_data = chip_config;
-	}
-
 	reg_val = readl(mdata->base + SPI_CMD_REG);
 	if (cpha)
 		reg_val |= SPI_CMD_CPHA;
@@ -406,6 +400,16 @@ static bool mtk_spi_can_dma(struct spi_master *master,
 	return xfer->len > MTK_SPI_MAX_FIFO_SIZE;
 }
 
+static int mtk_spi_setup(struct spi_device *spi)
+{
+	struct mtk_spi *mdata = spi_master_get_devdata(spi->master);
+
+	if (!spi->controller_data)
+		spi->controller_data = (void *)&mtk_default_chip_info;
+
+	return 0;
+}
+
 static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id)
 {
 	u32 cmd, reg_val, cnt;
@@ -493,6 +497,7 @@ static int mtk_spi_probe(struct platform_device *pdev)
 	master->prepare_message = mtk_spi_prepare_message;
 	master->transfer_one = mtk_spi_transfer_one;
 	master->can_dma = mtk_spi_can_dma;
+	master->setup = mtk_spi_setup;
 
 	of_id = of_match_node(mtk_spi_of_match, pdev->dev.of_node);
 	if (!of_id) {
-- 
1.8.1.1.dirty

[PATCH 4/5] spi: mediatek: mt8173 spi multiple devices support

[Leilk Liu]

mt8173 IC spi HW has 4 gpio group, it's possible to support
max <= 4 slave devices, even mtk spi HW is not congruent to spi core.
1. When a device do a spi_message transfer, spi HW should know
   which pad-group this device is on, and then writes pad-select
   register.
2. Mtk pad-select register just selects which MISO pin HW will
   receive data. For example, pad-select=1(select spi1 pins), HW just
   receives data from spi1 MISO, but it still send waveform to all 4
   group cs/clk/mosi. If cs pin in other groups is still spi mode,
   after spi1 is selected(by active cs pin), devices on other group
   will also be selected.

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
---
 drivers/spi/spi-mt65xx.c | 65 ++++++++++++++++++++++++++++++++++++++----------
 1 file changed, 52 insertions(+), 13 deletions(-)
 mode change 100755 => 100644 drivers/spi/spi-mt65xx.c

diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c
old mode 100755
new mode 100644
index 406695a..563954a
--- a/drivers/spi/spi-mt65xx.c
+++ b/drivers/spi/spi-mt65xx.c
@@ -20,6 +20,7 @@
 #include <linux/ioport.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_gpio.h>
 #include <linux/platform_device.h>
 #include <linux/platform_data/spi-mt65xx.h>
 #include <linux/pm_runtime.h>
@@ -84,7 +85,8 @@ struct mtk_spi_compatible {
 struct mtk_spi {
 	void __iomem *base;
 	u32 state;
-	u32 pad_sel;
+	int pad_num;
+	u32 *pad_sel;
 	struct clk *parent_clk, *sel_clk, *spi_clk;
 	struct spi_transfer *cur_transfer;
 	u32 xfer_len;
@@ -188,7 +190,8 @@ static int mtk_spi_prepare_message(struct spi_master *master,
 
 	/* pad select */
 	if (mdata->dev_comp->need_pad_sel)
-		writel(mdata->pad_sel, mdata->base + SPI_PAD_SEL_REG);
+		writel(mdata->pad_sel[spi->chip_select],
+		       mdata->base + SPI_PAD_SEL_REG);
 
 	return 0;
 }
@@ -407,6 +410,9 @@ static int mtk_spi_setup(struct spi_device *spi)
 	if (!spi->controller_data)
 		spi->controller_data = (void *)&mtk_default_chip_info;
 
+	if (mdata->dev_comp->need_pad_sel)
+		gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
+
 	return 0;
 }
 
@@ -481,7 +487,7 @@ static int mtk_spi_probe(struct platform_device *pdev)
 	struct mtk_spi *mdata;
 	const struct of_device_id *of_id;
 	struct resource *res;
-	int irq, ret;
+	int i, irq, ret;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*mdata));
 	if (!master) {
@@ -512,21 +518,34 @@ static int mtk_spi_probe(struct platform_device *pdev)
 		master->flags = SPI_MASTER_MUST_TX;
 
 	if (mdata->dev_comp->need_pad_sel) {
-		ret = of_property_read_u32(pdev->dev.of_node,
-					   "mediatek,pad-select",
-					   &mdata->pad_sel);
-		if (ret) {
-			dev_err(&pdev->dev, "failed to read pad select: %d\n",
-				ret);
+		mdata->pad_num = of_property_count_u32_elems(
+			pdev->dev.of_node,
+			"mediatek,pad-select");
+		if (mdata->pad_num < 0) {
+			dev_err(&pdev->dev,
+				"No 'mediatek,pad-select' property\n");
+			ret = -EINVAL;
 			goto err_put_master;
 		}
 
-		if (mdata->pad_sel > MT8173_SPI_MAX_PAD_SEL) {
-			dev_err(&pdev->dev, "wrong pad-select: %u\n",
-				mdata->pad_sel);
-			ret = -EINVAL;
+		mdata->pad_sel = devm_kmalloc_array(&pdev->dev, mdata->pad_num,
+						    sizeof(u32), GFP_KERNEL);
+		if (!mdata->pad_sel) {
+			ret = -ENOMEM;
 			goto err_put_master;
 		}
+
+		for (i = 0; i < mdata->pad_num; i++) {
+			of_property_read_u32_index(pdev->dev.of_node,
+						   "mediatek,pad-select",
+						   i, &mdata->pad_sel[i]);
+			if (mdata->pad_sel[i] > MT8173_SPI_MAX_PAD_SEL) {
+				dev_err(&pdev->dev, "wrong pad-sel[%d]: %u\n",
+					i, mdata->pad_sel[i]);
+				ret = -EINVAL;
+				goto err_put_master;
+			}
+		}
 	}
 
 	platform_set_drvdata(pdev, master);
@@ -604,6 +623,26 @@ static int mtk_spi_probe(struct platform_device *pdev)
 		goto err_put_master;
 	}
 
+	if (mdata->dev_comp->need_pad_sel) {
+		if (mdata->pad_num != master->num_chipselect) {
+			dev_err(&pdev->dev,
+				"pad_num does not match num_chipselect(%d != %d)\n",
+				mdata->pad_num, master->num_chipselect);
+			ret = -EINVAL;
+			goto err_put_master;
+		}
+
+		for (i = 0; i < master->num_chipselect; i++) {
+			ret = devm_gpio_request(&pdev->dev, master->cs_gpios[i],
+						dev_name(&pdev->dev));
+			if (ret) {
+				dev_err(&pdev->dev,
+					"can't get CS GPIO %i\n", i);
+				goto err_put_master;
+			}
+		}
+	}
+
 	return 0;
 
 err_disable_clk:
-- 
1.8.1.1.dirty

[PATCH 5/5] arm64: dts: spi bus dts support multiple devices

[Leilk Liu]

This patch support multiple devices for MT8173.

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
---
 arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
index 04b38ed..1c8c407 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
@@ -194,7 +194,7 @@
 			pinmux = <MT8173_PIN_69_SPI_CK__FUNC_SPI_CK_0_>,
 				<MT8173_PIN_70_SPI_MI__FUNC_SPI_MI_0_>,
 				<MT8173_PIN_71_SPI_MO__FUNC_SPI_MO_0_>,
-				<MT8173_PIN_72_SPI_CS__FUNC_SPI_CS_0_>;
+				<MT8173_PIN_72_SPI_CS__FUNC_GPIO72>;
 		};
 	};
 };
@@ -399,6 +399,7 @@
 &spi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi_pins_a>;
+	cs-gpios = <&pio 72 0>;
 	mediatek,pad-select = <0>;
 	status = "okay";
 };
-- 
1.8.1.1.dirty

[PATCH 5/5] arm64: dts: spi bus dts support multiple devices

[Sascha Hauer]

On Wed, Oct 14, 2015 at 11:23:35AM +0800, Leilk Liu wrote:
> This patch support multiple devices for MT8173.

The subject of this patch and also the above sentence should contain the
board name this patch is changing so that the reader knows this is about
a single board, and not arm64 in general.

Sascha

> 
> Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
> ---
>  arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> index 04b38ed..1c8c407 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> @@ -194,7 +194,7 @@
>  			pinmux = <MT8173_PIN_69_SPI_CK__FUNC_SPI_CK_0_>,
>  				<MT8173_PIN_70_SPI_MI__FUNC_SPI_MI_0_>,
>  				<MT8173_PIN_71_SPI_MO__FUNC_SPI_MO_0_>,
> -				<MT8173_PIN_72_SPI_CS__FUNC_SPI_CS_0_>;
> +				<MT8173_PIN_72_SPI_CS__FUNC_GPIO72>;
>  		};
>  	};
>  };
> @@ -399,6 +399,7 @@
>  &spi {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&spi_pins_a>;
> +	cs-gpios = <&pio 72 0>;
>  	mediatek,pad-select = <0>;
>  	status = "okay";
>  };
> -- 
> 1.8.1.1.dirty
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH 5/5] arm64: dts: spi bus dts support multiple devices

[lei liu]

Hi Sascha,

On Wed, 2015-10-14 at 07:58 +0200, Sascha Hauer wrote:
> On Wed, Oct 14, 2015 at 11:23:35AM +0800, Leilk Liu wrote:
> > This patch support multiple devices for MT8173.
> 
> The subject of this patch and also the above sentence should contain the
> board name this patch is changing so that the reader knows this is about
> a single board, and not arm64 in general.
> 
OK, I'll fix it.

> Sascha
> 
> > 
> > Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
> > ---
> >  arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 3 ++-
> >  1 file changed, 2 insertions(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> > index 04b38ed..1c8c407 100644
> > --- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> > +++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> > @@ -194,7 +194,7 @@
> >  			pinmux = <MT8173_PIN_69_SPI_CK__FUNC_SPI_CK_0_>,
> >  				<MT8173_PIN_70_SPI_MI__FUNC_SPI_MI_0_>,
> >  				<MT8173_PIN_71_SPI_MO__FUNC_SPI_MO_0_>,
> > -				<MT8173_PIN_72_SPI_CS__FUNC_SPI_CS_0_>;
> > +				<MT8173_PIN_72_SPI_CS__FUNC_GPIO72>;
> >  		};
> >  	};
> >  };
> > @@ -399,6 +399,7 @@
> >  &spi {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&spi_pins_a>;
> > +	cs-gpios = <&pio 72 0>;
> >  	mediatek,pad-select = <0>;
> >  	status = "okay";
> >  };
> > -- 
> > 1.8.1.1.dirty
> > 
> > 
> 

[PATCH 0/5] mt8173 spi multiple devices support

[Mark Brown]

On Wed, Oct 14, 2015 at 11:23:30AM +0800, Leilk Liu wrote:
> This series are based on 4.3-rc1 and provide 5 patches to support
> mt8173 spi multiple devices.

This doesn't apply against current code, please check and resend.  Also
note that it looks like you've got the execute bit set on some of the
files.  The code itself looks fine.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151019/2bcf4997/attachment.sig>

[PATCH 0/5] mt8173 spi multiple devices support

[lei liu]

Hi Mark,

On Mon, 2015-10-19 at 20:27 +0100, Mark Brown wrote:
> On Wed, Oct 14, 2015 at 11:23:30AM +0800, Leilk Liu wrote:
> > This series are based on 4.3-rc1 and provide 5 patches to support
> > mt8173 spi multiple devices.
> 
> This doesn't apply against current code, please check and resend.  Also
> note that it looks like you've got the execute bit set on some of the
> files.  The code itself looks fine.

OK, I will fix it.