From: antoine.tenart@free-electrons.com (Antoine Tenart)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 3/4] mtd: pxa3xx_nand: rework flash detection and timing setup
Date: Thu, 15 Oct 2015 09:17:30 +0200 [thread overview]
Message-ID: <1444893451-16610-4-git-send-email-antoine.tenart@free-electrons.com> (raw)
In-Reply-To: <1444893451-16610-1-git-send-email-antoine.tenart@free-electrons.com>
Rework the pxa3xx_nand driver to allow using functions exported by the
nand framework to detect the flash and the timings. Then setup the
timings using the helpers previously added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
---
drivers/mtd/nand/pxa3xx_nand.c | 118 +++++++++--------------------------------
1 file changed, 25 insertions(+), 93 deletions(-)
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index da52f21570cf..45e5e660d421 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -1363,45 +1363,16 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
return NAND_STATUS_READY;
}
-static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
- const struct pxa3xx_nand_flash *f)
+static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info)
{
- struct platform_device *pdev = info->pdev;
- struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct pxa3xx_nand_host *host = info->host[info->cs];
- uint32_t ndcr = 0x0; /* enable all interrupts */
-
- if (f->page_size != 2048 && f->page_size != 512) {
- dev_err(&pdev->dev, "Current only support 2048 and 512 size\n");
- return -EINVAL;
- }
-
- if (f->flash_width != 16 && f->flash_width != 8) {
- dev_err(&pdev->dev, "Only support 8bit and 16 bit!\n");
- return -EINVAL;
- }
-
- /* calculate addressing information */
- host->col_addr_cycles = (f->page_size == 2048) ? 2 : 1;
-
- if (f->num_blocks * f->page_per_block > 65536)
- host->row_addr_cycles = 3;
- else
- host->row_addr_cycles = 2;
-
- ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
- ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
- ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0;
- ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0;
- ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0;
- ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0;
-
- ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
- ndcr |= NDCR_SPARE_EN; /* enable spare by default */
+ struct mtd_info *mtd = host->mtd;
+ struct nand_chip *chip = mtd->priv;
- info->reg_ndcr = ndcr;
+ info->reg_ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
+ info->reg_ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0;
+ info->reg_ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0;
- pxa3xx_nand_set_timing(host, f->timing);
return 0;
}
@@ -1483,19 +1454,31 @@ static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info)
}
#endif
-static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info)
+static int pxa3xx_nand_sensing(struct pxa3xx_nand_host *host)
{
+ struct pxa3xx_nand_info *info = host->info_data;
+ struct platform_device *pdev = info->pdev;
+ struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
struct mtd_info *mtd;
struct nand_chip *chip;
+ const struct nand_sdr_timings *timings;
int ret;
mtd = info->host[info->cs]->mtd;
chip = mtd->priv;
+ /* configure default flash values */
+ info->reg_ndcr = 0x0; /* enable all interrupts */
+ info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
+ info->reg_ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
+ info->reg_ndcr |= NDCR_SPARE_EN; /* enable spare by default */
+
/* use the common timing to make a try */
- ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]);
- if (ret)
- return ret;
+ timings = onfi_async_timing_mode_to_sdr_timings(0);
+ if (IS_ERR(timings))
+ return PTR_ERR(timings);
+
+ pxa3xx_nand_set_sdr_timing(host, timings);
chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
ret = chip->waitfunc(mtd, chip);
@@ -1580,12 +1563,8 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
struct pxa3xx_nand_info *info = host->info_data;
struct platform_device *pdev = info->pdev;
struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
- struct nand_flash_dev pxa3xx_flash_ids[2], *def = NULL;
- const struct pxa3xx_nand_flash *f = NULL;
struct nand_chip *chip = mtd->priv;
- uint32_t id = -1;
- uint64_t chipsize;
- int i, ret, num;
+ int ret;
uint16_t ecc_strength, ecc_step;
if (pdata->keep_config && !pxa3xx_nand_detect_config(info))
@@ -1594,7 +1573,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
/* Set a default chunk size */
info->chunk_size = 512;
- ret = pxa3xx_nand_sensing(info);
+ ret = pxa3xx_nand_sensing(host);
if (ret) {
dev_info(&info->pdev->dev, "There is no chip on cs %d!\n",
info->cs);
@@ -1602,53 +1581,6 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
return ret;
}
- chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0);
- id = *((uint16_t *)(info->data_buff));
- if (id != 0)
- dev_info(&info->pdev->dev, "Detect a flash id %x\n", id);
- else {
- dev_warn(&info->pdev->dev,
- "Read out ID 0, potential timing set wrong!!\n");
-
- return -EINVAL;
- }
-
- num = ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1;
- for (i = 0; i < num; i++) {
- if (i < pdata->num_flash)
- f = pdata->flash + i;
- else
- f = &builtin_flash_types[i - pdata->num_flash + 1];
-
- /* find the chip in default list */
- if (f->chip_id == id)
- break;
- }
-
- if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) {
- dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n");
-
- return -EINVAL;
- }
-
- ret = pxa3xx_nand_config_flash(info, f);
- if (ret) {
- dev_err(&info->pdev->dev, "ERROR! Configure failed\n");
- return ret;
- }
-
- memset(pxa3xx_flash_ids, 0, sizeof(pxa3xx_flash_ids));
-
- pxa3xx_flash_ids[0].name = f->name;
- pxa3xx_flash_ids[0].dev_id = (f->chip_id >> 8) & 0xffff;
- pxa3xx_flash_ids[0].pagesize = f->page_size;
- chipsize = (uint64_t)f->num_blocks * f->page_per_block * f->page_size;
- pxa3xx_flash_ids[0].chipsize = chipsize >> 20;
- pxa3xx_flash_ids[0].erasesize = f->page_size * f->page_per_block;
- if (f->flash_width == 16)
- pxa3xx_flash_ids[0].options = NAND_BUSWIDTH_16;
- pxa3xx_flash_ids[1].name = NULL;
- def = pxa3xx_flash_ids;
KEEP_CONFIG:
if (info->reg_ndcr & NDCR_DWIDTH_M)
chip->options |= NAND_BUSWIDTH_16;
@@ -1657,7 +1589,7 @@ KEEP_CONFIG:
if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
nand_writel(info, NDECCCTRL, 0x0);
- if (nand_scan_ident(mtd, 1, def))
+ if (nand_scan_ident(mtd, 1, NULL))
return -ENODEV;
if (!pdata->keep_config) {
--
2.6.1
next prev parent reply other threads:[~2015-10-15 7:17 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-15 7:17 [PATCH v3 0/4] mtd: pxa3xx_nand: rework the timing setup Antoine Tenart
2015-10-15 7:17 ` [PATCH v3 1/4] mtd: nand: allow compile test of MTD_NAND_PXA3xx Antoine Tenart
2015-10-15 9:12 ` kbuild test robot
2015-10-15 11:44 ` Arnd Bergmann
2015-10-15 11:52 ` Antoine Tenart
2015-10-15 7:17 ` [PATCH v3 2/4] mtd: pxa3xx_nand: add helpers to setup the timings Antoine Tenart
2015-10-17 13:57 ` Ezequiel Garcia
2015-10-19 9:32 ` Antoine Tenart
2015-10-15 7:17 ` Antoine Tenart [this message]
2015-10-17 14:01 ` [PATCH v3 3/4] mtd: pxa3xx_nand: rework flash detection and timing setup Ezequiel Garcia
2015-10-19 9:32 ` Antoine Tenart
2015-10-15 7:17 ` [PATCH v3 4/4] mtd: pxa3xx_nand: clean up the pxa3xx timings Antoine Tenart
2015-10-15 18:30 ` [PATCH v3 0/4] mtd: pxa3xx_nand: rework the timing setup Ezequiel Garcia
2015-10-16 6:38 ` Antoine Tenart
2015-10-20 19:30 ` Robert Jarzmik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1444893451-16610-4-git-send-email-antoine.tenart@free-electrons.com \
--to=antoine.tenart@free-electrons.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).