[PATCH 1/2] devicetree: bindings: Add vendor prefix for Kosagi

[PATCH 1/2] devicetree: bindings: Add vendor prefix for Kosagi

[Marek Vasut]

From: Sean Cross <xobs@kosagi.com>

Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the
more common name of Kosagi.

Signed-off-by: Sean Cross <xobs@kosagi.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 55df1d4..a51e829 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -123,6 +123,7 @@ jedec	JEDEC Solid State Technology Association
 karo	Ka-Ro electronics GmbH
 keymile	Keymile GmbH
 kinetic Kinetic Technologies
+kosagi	Sutajio Ko-Usagi PTE Ltd.
 lacie	LaCie
 lantiq	Lantiq Semiconductor
 lenovo	Lenovo Group Ltd.
-- 
2.1.4

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

From: Sean Cross <xobs@kosagi.com>

Novena is an open-hardware laptop/desktop/bare board.

See http://www.kosagi.com/w/index.php?title=Novena_Main_Page

Signed-off-by: Sean Cross <xobs@kosagi.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
---
 arch/arm/boot/dts/Makefile         |   1 +
 arch/arm/boot/dts/imx6q-novena.dts | 825 +++++++++++++++++++++++++++++++++++++
 2 files changed, 826 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-novena.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 30bbc37..6f9bcac 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-hummingboard.dtb \
 	imx6q-nitrogen6x.dtb \
 	imx6q-nitrogen6_max.dtb \
+	imx6q-novena.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-rex-pro.dtb \
 	imx6q-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts
new file mode 100644
index 0000000..9544f04
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-novena.dts
@@ -0,0 +1,825 @@
+/*
+ * Copyright 2014 Sutajio Ko-Usagi PTE LTD
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Kosagi Novena Dual/Quad";
+	compatible = "kosagi,imx6q-novena", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0xefffffff>;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_2p5v: 2p5v {
+			compatible = "regulator-fixed";
+			regulator-name = "2P5V";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			regulator-always-on;
+		};
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usb_otg_vbus: usb_otg_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+		};
+
+		reg_audio_codec: es8328-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "es8328-power";
+			regulator-boot-on;
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <400000>;
+			gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_pcie: pcie-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "pcie-bus-power";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_lvds_lcd: lcd-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-lvds-power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_display: display-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-display-power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			startup-delay-us = <200000>;
+			gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_sata: sata-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "sata-power";
+			regulator-boot-on;
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			startup-delay-us = <10000>;
+			gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys_novena>;
+
+		user-button {
+			label = "User Button";
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		lid {
+			label = "Lid";
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,input-type = <5>;	/* EV_SW */
+			linux,code = <0>;	/* SW_LID */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_novena>;
+
+		heartbeat {
+			label = "novena:white:panel";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 10000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_novena>;
+		power-supply = <&reg_lvds_lcd>;
+
+		brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>;
+		default-brightness-level = <12>;
+	};
+
+	panel: panel {
+		compatible = "innolux,n133hse-ea1", "simple-panel";
+		backlight = <&backlight>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-es8328";
+		model = "imx-audio-es8328";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-amp-supply = <&reg_audio_codec>;
+		jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>;
+		audio-routing = 
+			"Speaker", "LOUT2",
+			"Speaker", "ROUT2",
+			"Speaker", "audio-amp",
+			"Headphone", "ROUT1",
+			"Headphone", "LOUT1",
+			"LINPUT1", "Mic Jack",
+			"RINPUT1", "Mic Jack",
+			"Mic Jack", "Mic Bias";
+		mux-int-port = <0x1>;
+		mux-ext-port = <0x3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_novena>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_novena>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+	mac-address = [00 00 00 00 00 00];
+	rxc-skew-ps = <3000>;
+	rxdv-skew-ps = <0>;
+	txc-skew-ps = <3000>;
+	txen-skew-ps = <0>;
+	rxd0-skew-ps = <0>;
+	rxd1-skew-ps = <0>;
+	rxd2-skew-ps = <0>;
+	rxd3-skew-ps = <0>;
+	txd0-skew-ps = <3000>;
+	txd1-skew-ps = <3000>;
+	txd2-skew-ps = <3000>;
+	txd3-skew-ps = <3000>;
+	status = "okay";
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3_novena>;
+	fsl,spi-num-chipselects = <3>;
+	status = "okay";
+
+	spidev at 0 {
+		compatible = "spidev";
+		spi-max-frequency = <30000000>;
+		reg = <0>;
+	};
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_novena>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_novena>;
+	status = "okay";
+
+	sbs_battery: bq20z75 at 0b {
+		compatible = "sbs,sbs-battery";
+		reg = <0x0b>;
+		sbs,i2c-retry-count = <50>;
+	};
+
+	stmpe811 at 44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		id = <0>;
+		blocks = <0x5>;
+		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe_novena>;
+		vio-supply = <&reg_3p3v>;
+		vcc-supply = <&reg_3p3v>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	accel: mma8452 at 1c {
+		compatible = "fsl,mma8452";
+		reg = <0x1c>;
+	};
+
+	rtc: pcf8523 at 68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2_novena>;
+	status = "okay";
+
+	pmic: pfuze100 at 08 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_novena>;
+	status = "okay";
+
+	codec: es8328 at 11 {
+		compatible = "everest,es8328";
+		reg = <0x11>;
+		DVDD-supply = <&reg_audio_codec>;
+		AVDD-supply = <&reg_audio_codec>;
+		PVDD-supply = <&reg_audio_codec>;
+		HPVDD-supply = <&reg_audio_codec>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sound_novena>;
+
+		clocks = <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>, <&clks IMX6QDL_CLK_CKO1_SEL>, <&clks IMX6QDL_CLK_PLL4_AUDIO>, <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_CKO1_PODF>;
+		assigned-clock-rates = <0 0 722534400 22579200>;
+	};
+};
+
+&iomuxc {
+	audmux {
+		pinctrl_audmux_novena: audmuxgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x80000000
+				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x80000000
+				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x80000000
+				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000
+			>;
+		};
+	};
+
+	kpp-keys {
+		pinctrl_kpp_novena: kppgrp-novena {
+			fsl,pins = <
+				/* Front panel button */
+				MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1
+
+				/* Fake column driver, not connected */
+				MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1
+			>;
+		};
+	};	
+		
+	backlight {
+		pinctrl_backlight_novena: backlightgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT8__PWM1_OUT   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x80000000
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15   0x80000000
+			>;
+		};
+	};
+
+	ecspi3 {
+		pinctrl_ecspi3_novena: ecspi3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+			>;
+		};
+	};
+
+	enet {
+		pinctrl_enet_novena: enetgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC         0x1b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0x1b020
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0x1b028
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0x1b028
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0x1b028
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0x1b028
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x1b0b0
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x1b0b0
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x1b0b0
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK      0x4001b0a8
+
+				/* Ethernet reset */
+				MX6QDL_PAD_EIM_D23__GPIO3_IO23  0x80000000
+			>;
+		};
+	};
+
+	gpio_keys {
+		pinctrl_gpio_keys_novena: gpiokeysgrp-novena {
+			fsl,pins = <
+				/* User button */
+				MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0
+
+				/* PCIe Wakeup */
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x1f0e0
+
+				/* Lid switch */
+				MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
+			>;
+		};
+	};
+
+	hdmi {
+		pinctrl_hdmi_novena: hdmigrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+				MX6QDL_PAD_EIM_A24__GPIO5_IO04        0x80000000
+			>;
+		};
+	};
+
+	i2c1 {
+		pinctrl_i2c1_novena: i2c1grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+				MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+			>;
+		};
+	};
+
+	i2c2 {
+		pinctrl_i2c2_novena: i2c2grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
+				MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
+			>;
+		};
+	};
+
+	i2c3 {
+		pinctrl_i2c3_novena: i2c3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+			>;
+		};
+	};
+
+	leds {
+		pinctrl_leds_novena: ledsgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x80000000
+			>;
+		};
+	};
+
+	fpga {
+		pinctrl_fpga_gpio: fpgagpiogrp-novena {
+			fsl,pins = <
+				/* FPGA power */
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x80000000
+
+				/* Reset */
+				MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x80000000
+
+				/* FPGA GPIOs */
+				MX6QDL_PAD_EIM_DA0__GPIO3_IO00	0x80000000
+				MX6QDL_PAD_EIM_DA1__GPIO3_IO01	0x80000000
+				MX6QDL_PAD_EIM_DA2__GPIO3_IO02	0x80000000
+				MX6QDL_PAD_EIM_DA3__GPIO3_IO03	0x80000000
+				MX6QDL_PAD_EIM_DA4__GPIO3_IO04	0x80000000
+				MX6QDL_PAD_EIM_DA5__GPIO3_IO05  0x80000000
+				MX6QDL_PAD_EIM_DA6__GPIO3_IO06  0x80000000
+				MX6QDL_PAD_EIM_DA7__GPIO3_IO07  0x80000000
+				MX6QDL_PAD_EIM_DA8__GPIO3_IO08	0x80000000
+				MX6QDL_PAD_EIM_DA9__GPIO3_IO09	0x80000000
+				MX6QDL_PAD_EIM_DA10__GPIO3_IO10	0x80000000
+				MX6QDL_PAD_EIM_DA11__GPIO3_IO11	0x80000000
+				MX6QDL_PAD_EIM_DA12__GPIO3_IO12	0x80000000
+				MX6QDL_PAD_EIM_DA13__GPIO3_IO13	0x80000000
+				MX6QDL_PAD_EIM_DA14__GPIO3_IO14	0x80000000
+				MX6QDL_PAD_EIM_DA15__GPIO3_IO15	0x80000000
+				MX6QDL_PAD_EIM_A16__GPIO2_IO22  0x80000000
+				MX6QDL_PAD_EIM_A17__GPIO2_IO21  0x80000000
+				MX6QDL_PAD_EIM_A18__GPIO2_IO20  0x80000000
+				MX6QDL_PAD_EIM_CS0__GPIO2_IO23	0x80000000
+				MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x80000000
+				MX6QDL_PAD_EIM_LBA__GPIO2_IO27  0x80000000
+				MX6QDL_PAD_EIM_OE__GPIO2_IO25   0x80000000
+				MX6QDL_PAD_EIM_RW__GPIO2_IO26   0x80000000
+				MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x80000000
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x80000000
+			>;
+		};
+
+		pinctrl_fpga_eim: fpgaeimgrp-novena {
+			fsl,pins = <
+				/* FPGA power */
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x80000000
+
+				/* Reset */
+				MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x80000000
+
+				/* FPGA GPIOs */
+				MX6QDL_PAD_EIM_DA0__EIM_AD00    0xb0f1
+				MX6QDL_PAD_EIM_DA1__EIM_AD01    0xb0f1
+				MX6QDL_PAD_EIM_DA2__EIM_AD02    0xb0f1
+				MX6QDL_PAD_EIM_DA3__EIM_AD03    0xb0f1
+				MX6QDL_PAD_EIM_DA4__EIM_AD04    0xb0f1
+				MX6QDL_PAD_EIM_DA5__EIM_AD05    0xb0f1
+				MX6QDL_PAD_EIM_DA6__EIM_AD06    0xb0f1
+				MX6QDL_PAD_EIM_DA7__EIM_AD07    0xb0f1
+				MX6QDL_PAD_EIM_DA8__EIM_AD08    0xb0f1
+				MX6QDL_PAD_EIM_DA9__EIM_AD09    0xb0f1
+				MX6QDL_PAD_EIM_DA10__EIM_AD10   0xb0f1
+				MX6QDL_PAD_EIM_DA11__EIM_AD11   0xb0f1
+				MX6QDL_PAD_EIM_DA12__EIM_AD12   0xb0f1
+				MX6QDL_PAD_EIM_DA13__EIM_AD13   0xb0f1
+				MX6QDL_PAD_EIM_DA14__EIM_AD14   0xb0f1
+				MX6QDL_PAD_EIM_DA15__EIM_AD15   0xb0f1
+				MX6QDL_PAD_EIM_A16__EIM_ADDR16  0xb0f1
+				MX6QDL_PAD_EIM_A17__EIM_ADDR17  0xb0f1
+				MX6QDL_PAD_EIM_A18__EIM_ADDR18  0xb0f1
+				MX6QDL_PAD_EIM_CS0__EIM_CS0_B   0xb0f1
+				MX6QDL_PAD_EIM_CS1__EIM_CS1_B   0xb0f1
+				MX6QDL_PAD_EIM_LBA__EIM_LBA_B   0xb0f1
+				MX6QDL_PAD_EIM_OE__EIM_OE_B     0xb0f1
+				MX6QDL_PAD_EIM_RW__EIM_RW       0xb0f1
+				MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1
+				MX6QDL_PAD_EIM_BCLK__EIM_BCLK   0xb0f1
+			>;
+		};
+	};
+
+	pcie {
+		pinctrl_pcie_novena: pciegrp-novena {
+			fsl,pins = <
+				/* Reset */
+				MX6QDL_PAD_EIM_D29__GPIO3_IO29  0x80000000
+
+				/* Power On */
+				MX6QDL_PAD_GPIO_17__GPIO7_IO12  0x80000000
+
+				/* Wifi kill */
+				MX6QDL_PAD_EIM_A22__GPIO2_IO16  0x80000000
+			>;
+		};
+	};
+
+	sata {
+		pinctrl_sata_novena: satagrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D30__GPIO3_IO30  0x80000000
+			>;
+		};
+	};
+
+	senoko {
+		pinctrl_senoko_novena: senokogrp-novena {
+			fsl,pins = <
+				/* Senoko IRQ line */
+				MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048
+
+				/* Senoko reset line */
+				MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x80000000
+			>;
+		};
+	};
+
+	sound {
+		pinctrl_sound_novena: soundgrp-novena {
+			fsl,pins = <
+				/* Audio power regulator */
+				MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x80000000
+
+				/* Headphone plug */
+				MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x80000000
+
+				MX6QDL_PAD_GPIO_0__CCM_CLKO1       0x80000000
+			>;
+		};
+	};
+
+	ts {
+		pinctrl_stmpe_novena: stmpegrp-novena {
+			fsl,pins = <
+				/* Touchscreen interrupt */
+				MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x80000000
+			>;
+		};
+	};
+
+	uart2 {
+		pinctrl_uart2_novena: uart2grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D26__UART2_TX_DATA   0x1b0b1
+				MX6QDL_PAD_EIM_D27__UART2_RX_DATA   0x1b0b1
+			>;
+		};
+	};
+
+	uart3 {
+		pinctrl_uart3_novena: uart3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+				MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+			>;
+		};
+	};
+	uart4 {
+		pinctrl_uart4_novena: uart4grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+			>;
+		};
+	};
+
+	usbotg {
+		pinctrl_usbotg_novena: usbotggrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+			>;
+		};
+	};
+
+	usdhc2 {
+		pinctrl_usdhc2_novena: usdhc2grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x170f9
+				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x100f9
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
+
+				/* Write protect */
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02   0x80000000
+
+				/* Card detect */
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04   0x80000000
+			>;
+		};
+	};
+
+	usdhc3 {
+		pinctrl_usdhc3_novena: usdhc3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170f9
+				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100f9
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+			>;
+		};
+	};
+};
+
+&kpp {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_kpp_novena>;
+	linux,keymap = <
+		MATRIX_KEY(1, 1, KEY_CONFIG)
+	>;
+	status = "okay";
+};
+
+&ldb {
+	fsl,dual-channel;
+	status = "okay";
+	lvds-channel at 0 {
+		fsl,data-mapping = "jeida";
+		fsl,data-width = <24>;
+		fsl,panel = <&panel>;
+		status = "okay";
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie_novena>;
+	reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+	bus-supply = <&reg_pcie>;
+	status = "okay";
+};
+
+&sata {
+	target-supply = <&reg_sata>;
+	fsl,transmit-level-mV = <1025>;
+	fsl,transmit-boost-mdB = <0>;
+	fsl,transmit-atten-16ths = <8>;
+	status = "okay";
+};
+
+&ssi1 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_novena>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_novena>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4_novena>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg_novena>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&swbst_reg>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_novena>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_novena>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
-- 
2.1.4

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Lucas Stach]

Hi Marek,

some comments below.

Am Mittwoch, den 18.11.2015, 10:48 +0100 schrieb Marek Vasut:
> From: Sean Cross <xobs@kosagi.com>
> 
> Novena is an open-hardware laptop/desktop/bare board.
> 
> See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
> 
> Signed-off-by: Sean Cross <xobs@kosagi.com>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Fabio Estevam <fabio.estevam@freescale.com>
> ---
>  arch/arm/boot/dts/Makefile         |   1 +
>  arch/arm/boot/dts/imx6q-novena.dts | 825 +++++++++++++++++++++++++++++++++++++
>  2 files changed, 826 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-novena.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 30bbc37..6f9bcac 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>  	imx6q-hummingboard.dtb \
>  	imx6q-nitrogen6x.dtb \
>  	imx6q-nitrogen6_max.dtb \
> +	imx6q-novena.dtb \
>  	imx6q-phytec-pbab01.dtb \
>  	imx6q-rex-pro.dtb \
>  	imx6q-sabreauto.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts
> new file mode 100644
> index 0000000..9544f04
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-novena.dts
> @@ -0,0 +1,825 @@
> +/*
> + * Copyright 2014 Sutajio Ko-Usagi PTE LTD
> + * Copyright 2012 Freescale Semiconductor, Inc.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Kosagi Novena Dual/Quad";
> +	compatible = "kosagi,imx6q-novena", "fsl,imx6q";
> +
> +	memory {
> +		reg = <0x10000000 0xefffffff>;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +

Remove this simple bus. It's not there in hardware, regulators are board
level components just like the nodes below.

> +		reg_2p5v: 2p5v {
> +			compatible = "regulator-fixed";
> +			regulator-name = "2P5V";
> +			regulator-min-microvolt = <2500000>;
> +			regulator-max-microvolt = <2500000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_3p3v: 3p3v {
> +			compatible = "regulator-fixed";
> +			regulator-name = "3P3V";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_usb_otg_vbus: usb_otg_vbus {
> +			compatible = "regulator-fixed";
> +			regulator-name = "usb_otg_vbus";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			enable-active-high;
> +		};
> +
> +		reg_audio_codec: es8328-regulator {
> +			compatible = "regulator-fixed";
> +			regulator-name = "es8328-power";
> +			regulator-boot-on;
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			startup-delay-us = <400000>;
> +			gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_pcie: pcie-regulator {
> +			compatible = "regulator-fixed";
> +			regulator-name = "pcie-bus-power";
> +			regulator-min-microvolt = <1500000>;
> +			regulator-max-microvolt = <1500000>;
> +			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;

Make this an always-on regulator for now. More comments about this
below.

> +		};
> +
> +		reg_lvds_lcd: lcd-regulator {
> +			compatible = "regulator-fixed";
> +			regulator-name = "lcd-lvds-power";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_display: display-regulator {
> +			compatible = "regulator-fixed";
> +			regulator-name = "lcd-display-power";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			startup-delay-us = <200000>;
> +			gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_sata: sata-regulator {
> +			compatible = "regulator-fixed";
> +			regulator-name = "sata-power";
> +			regulator-boot-on;
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			startup-delay-us = <10000>;
> +			gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_keys_novena>;
> +
> +		user-button {
> +			label = "User Button";
> +			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_POWER>;
> +		};
> +
> +		lid {
> +			label = "Lid";
> +			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
> +			linux,input-type = <5>;	/* EV_SW */
> +			linux,code = <0>;	/* SW_LID */
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_leds_novena>;
> +
> +		heartbeat {
> +			label = "novena:white:panel";
> +			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "default-on";
> +		};
> +	};
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm1 0 10000000>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_backlight_novena>;
> +		power-supply = <&reg_lvds_lcd>;
> +
> +		brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>;
> +		default-brightness-level = <12>;
> +	};
> +
> +	panel: panel {
> +		compatible = "innolux,n133hse-ea1", "simple-panel";
> +		backlight = <&backlight>;
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx-audio-es8328";
> +		model = "imx-audio-es8328";
> +		ssi-controller = <&ssi1>;
> +		audio-codec = <&codec>;
> +		audio-amp-supply = <&reg_audio_codec>;
> +		jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>;
> +		audio-routing = 
> +			"Speaker", "LOUT2",
> +			"Speaker", "ROUT2",
> +			"Speaker", "audio-amp",
> +			"Headphone", "ROUT1",
> +			"Headphone", "LOUT1",
> +			"LINPUT1", "Mic Jack",
> +			"RINPUT1", "Mic Jack",
> +			"Mic Jack", "Mic Bias";
> +		mux-int-port = <0x1>;
> +		mux-ext-port = <0x3>;
> +	};
> +};
> +
> +&audmux {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_audmux_novena>;
> +	status = "okay";
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet_novena>;
> +	phy-mode = "rgmii";
> +	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
> +	mac-address = [00 00 00 00 00 00];
> +	rxc-skew-ps = <3000>;
> +	rxdv-skew-ps = <0>;
> +	txc-skew-ps = <3000>;
> +	txen-skew-ps = <0>;
> +	rxd0-skew-ps = <0>;
> +	rxd1-skew-ps = <0>;
> +	rxd2-skew-ps = <0>;
> +	rxd3-skew-ps = <0>;
> +	txd0-skew-ps = <3000>;
> +	txd1-skew-ps = <3000>;
> +	txd2-skew-ps = <3000>;
> +	txd3-skew-ps = <3000>;
> +	status = "okay";
> +};
> +
> +&ecspi3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi3_novena>;
> +	fsl,spi-num-chipselects = <3>;
> +	status = "okay";
> +
> +	spidev at 0 {
> +		compatible = "spidev";

This will explode on a new kernel. Specifying spidev without using a
more specific compatible will trigger a WARN_ON(), as it's considered
bad style.

> +		spi-max-frequency = <30000000>;
> +		reg = <0>;
> +	};
> +};
> +
> +&hdmi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hdmi_novena>;
> +	ddc-i2c-bus = <&i2c2>;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1_novena>;
> +	status = "okay";
> +
> +	sbs_battery: bq20z75 at 0b {
> +		compatible = "sbs,sbs-battery";
> +		reg = <0x0b>;
> +		sbs,i2c-retry-count = <50>;
> +	};
> +
> +	stmpe811 at 44 {
> +		compatible = "st,stmpe811";
> +		reg = <0x44>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
> +		id = <0>;
> +		blocks = <0x5>;
> +		irq-trigger = <0x1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_stmpe_novena>;
> +		vio-supply = <&reg_3p3v>;
> +		vcc-supply = <&reg_3p3v>;
> +
> +		stmpe_touchscreen {
> +			compatible = "st,stmpe-ts";
> +			st,sample-time = <4>;
> +			st,mod-12b = <1>;
> +			st,ref-sel = <0>;
> +			st,adc-freq = <1>;
> +			st,ave-ctrl = <1>;
> +			st,touch-det-delay = <2>;
> +			st,settling = <2>;
> +			st,fraction-z = <7>;
> +			st,i-drive = <1>;
> +		};
> +	};
> +
> +	accel: mma8452 at 1c {
> +		compatible = "fsl,mma8452";
> +		reg = <0x1c>;
> +	};
> +
> +	rtc: pcf8523 at 68 {
> +		compatible = "nxp,pcf8523";
> +		reg = <0x68>;
> +	};
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2_novena>;
> +	status = "okay";
> +
> +	pmic: pfuze100 at 08 {
> +		compatible = "fsl,pfuze100";
> +		reg = <0x08>;
> +
> +		regulators {
> +			sw1a_reg: sw1ab {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw1c_reg: sw1c {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw2_reg: sw2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw3a_reg: sw3a {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw3b_reg: sw3b {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw4_reg: sw4 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			swbst_reg: swbst {
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5150000>;
> +				regulator-boot-on;
> +			};
> +
> +			snvs_reg: vsnvs {
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vref_reg: vrefddr {
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen1_reg: vgen1 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +			};
> +
> +			vgen2_reg: vgen2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +			};
> +
> +			vgen3_reg: vgen3 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			vgen4_reg: vgen4 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen5_reg: vgen5 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen6_reg: vgen6 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3_novena>;
> +	status = "okay";
> +
> +	codec: es8328 at 11 {
> +		compatible = "everest,es8328";
> +		reg = <0x11>;
> +		DVDD-supply = <&reg_audio_codec>;
> +		AVDD-supply = <&reg_audio_codec>;
> +		PVDD-supply = <&reg_audio_codec>;
> +		HPVDD-supply = <&reg_audio_codec>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_sound_novena>;
> +
> +		clocks = <&clks IMX6QDL_CLK_CKO1>;
> +		assigned-clocks = <&clks IMX6QDL_CLK_CKO>, <&clks IMX6QDL_CLK_CKO1_SEL>, <&clks IMX6QDL_CLK_PLL4_AUDIO>, <&clks IMX6QDL_CLK_CKO1>;
> +		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_CKO1_PODF>;
> +		assigned-clock-rates = <0 0 722534400 22579200>;
> +	};
> +};
> +
> +&iomuxc {
> +	audmux {
> +		pinctrl_audmux_novena: audmuxgrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x80000000
> +				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x80000000
> +				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x80000000
> +				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000
> +			>;
> +		};
> +	};
> +
> +	kpp-keys {
> +		pinctrl_kpp_novena: kppgrp-novena {
> +			fsl,pins = <
> +				/* Front panel button */
> +				MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1
> +
> +				/* Fake column driver, not connected */
> +				MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1
> +			>;
> +		};
> +	};	
> +		
> +	backlight {
> +		pinctrl_backlight_novena: backlightgrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_DISP0_DAT8__PWM1_OUT   0x1b0b0
> +				MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x80000000
> +				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15   0x80000000
> +			>;
> +		};
> +	};
> +
> +	ecspi3 {
> +		pinctrl_ecspi3_novena: ecspi3grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> +				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> +				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> +			>;
> +		};
> +	};
> +
> +	enet {
> +		pinctrl_enet_novena: enetgrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
> +				MX6QDL_PAD_ENET_MDC__ENET_MDC         0x1b0b0
> +				MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0x1b020
> +				MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0x1b028
> +				MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0x1b028
> +				MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0x1b028
> +				MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0x1b028
> +				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028
> +				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
> +				MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x1b0b0
> +				MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x1b0b0
> +				MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x1b0b0
> +				MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
> +				MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
> +				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> +				MX6QDL_PAD_GPIO_16__ENET_REF_CLK      0x4001b0a8
> +
> +				/* Ethernet reset */
> +				MX6QDL_PAD_EIM_D23__GPIO3_IO23  0x80000000
> +			>;
> +		};
> +	};
> +
> +	gpio_keys {
> +		pinctrl_gpio_keys_novena: gpiokeysgrp-novena {
> +			fsl,pins = <
> +				/* User button */
> +				MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0
> +
> +				/* PCIe Wakeup */
> +				MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x1f0e0
> +
> +				/* Lid switch */
> +				MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
> +			>;
> +		};
> +	};
> +
> +	hdmi {
> +		pinctrl_hdmi_novena: hdmigrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
> +				MX6QDL_PAD_EIM_A24__GPIO5_IO04        0x80000000
> +			>;
> +		};
> +	};
> +
> +	i2c1 {
> +		pinctrl_i2c1_novena: i2c1grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> +				MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> +			>;
> +		};
> +	};
> +
> +	i2c2 {
> +		pinctrl_i2c2_novena: i2c2grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
> +				MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
> +			>;
> +		};
> +	};
> +
> +	i2c3 {
> +		pinctrl_i2c3_novena: i2c3grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
> +				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> +			>;
> +		};
> +	};
> +
> +	leds {
> +		pinctrl_leds_novena: ledsgrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x80000000
> +			>;
> +		};
> +	};
> +
> +	fpga {
> +		pinctrl_fpga_gpio: fpgagpiogrp-novena {
> +			fsl,pins = <
> +				/* FPGA power */
> +				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x80000000
> +
> +				/* Reset */
> +				MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x80000000
> +
> +				/* FPGA GPIOs */
> +				MX6QDL_PAD_EIM_DA0__GPIO3_IO00	0x80000000
> +				MX6QDL_PAD_EIM_DA1__GPIO3_IO01	0x80000000
> +				MX6QDL_PAD_EIM_DA2__GPIO3_IO02	0x80000000
> +				MX6QDL_PAD_EIM_DA3__GPIO3_IO03	0x80000000
> +				MX6QDL_PAD_EIM_DA4__GPIO3_IO04	0x80000000
> +				MX6QDL_PAD_EIM_DA5__GPIO3_IO05  0x80000000
> +				MX6QDL_PAD_EIM_DA6__GPIO3_IO06  0x80000000
> +				MX6QDL_PAD_EIM_DA7__GPIO3_IO07  0x80000000
> +				MX6QDL_PAD_EIM_DA8__GPIO3_IO08	0x80000000
> +				MX6QDL_PAD_EIM_DA9__GPIO3_IO09	0x80000000
> +				MX6QDL_PAD_EIM_DA10__GPIO3_IO10	0x80000000
> +				MX6QDL_PAD_EIM_DA11__GPIO3_IO11	0x80000000
> +				MX6QDL_PAD_EIM_DA12__GPIO3_IO12	0x80000000
> +				MX6QDL_PAD_EIM_DA13__GPIO3_IO13	0x80000000
> +				MX6QDL_PAD_EIM_DA14__GPIO3_IO14	0x80000000
> +				MX6QDL_PAD_EIM_DA15__GPIO3_IO15	0x80000000
> +				MX6QDL_PAD_EIM_A16__GPIO2_IO22  0x80000000
> +				MX6QDL_PAD_EIM_A17__GPIO2_IO21  0x80000000
> +				MX6QDL_PAD_EIM_A18__GPIO2_IO20  0x80000000
> +				MX6QDL_PAD_EIM_CS0__GPIO2_IO23	0x80000000
> +				MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x80000000
> +				MX6QDL_PAD_EIM_LBA__GPIO2_IO27  0x80000000
> +				MX6QDL_PAD_EIM_OE__GPIO2_IO25   0x80000000
> +				MX6QDL_PAD_EIM_RW__GPIO2_IO26   0x80000000
> +				MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x80000000
> +				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x80000000
> +			>;
> +		};
> +
> +		pinctrl_fpga_eim: fpgaeimgrp-novena {
> +			fsl,pins = <
> +				/* FPGA power */
> +				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x80000000
> +
> +				/* Reset */
> +				MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x80000000
> +
> +				/* FPGA GPIOs */
> +				MX6QDL_PAD_EIM_DA0__EIM_AD00    0xb0f1
> +				MX6QDL_PAD_EIM_DA1__EIM_AD01    0xb0f1
> +				MX6QDL_PAD_EIM_DA2__EIM_AD02    0xb0f1
> +				MX6QDL_PAD_EIM_DA3__EIM_AD03    0xb0f1
> +				MX6QDL_PAD_EIM_DA4__EIM_AD04    0xb0f1
> +				MX6QDL_PAD_EIM_DA5__EIM_AD05    0xb0f1
> +				MX6QDL_PAD_EIM_DA6__EIM_AD06    0xb0f1
> +				MX6QDL_PAD_EIM_DA7__EIM_AD07    0xb0f1
> +				MX6QDL_PAD_EIM_DA8__EIM_AD08    0xb0f1
> +				MX6QDL_PAD_EIM_DA9__EIM_AD09    0xb0f1
> +				MX6QDL_PAD_EIM_DA10__EIM_AD10   0xb0f1
> +				MX6QDL_PAD_EIM_DA11__EIM_AD11   0xb0f1
> +				MX6QDL_PAD_EIM_DA12__EIM_AD12   0xb0f1
> +				MX6QDL_PAD_EIM_DA13__EIM_AD13   0xb0f1
> +				MX6QDL_PAD_EIM_DA14__EIM_AD14   0xb0f1
> +				MX6QDL_PAD_EIM_DA15__EIM_AD15   0xb0f1
> +				MX6QDL_PAD_EIM_A16__EIM_ADDR16  0xb0f1
> +				MX6QDL_PAD_EIM_A17__EIM_ADDR17  0xb0f1
> +				MX6QDL_PAD_EIM_A18__EIM_ADDR18  0xb0f1
> +				MX6QDL_PAD_EIM_CS0__EIM_CS0_B   0xb0f1
> +				MX6QDL_PAD_EIM_CS1__EIM_CS1_B   0xb0f1
> +				MX6QDL_PAD_EIM_LBA__EIM_LBA_B   0xb0f1
> +				MX6QDL_PAD_EIM_OE__EIM_OE_B     0xb0f1
> +				MX6QDL_PAD_EIM_RW__EIM_RW       0xb0f1
> +				MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1
> +				MX6QDL_PAD_EIM_BCLK__EIM_BCLK   0xb0f1
> +			>;
> +		};
> +	};
> +
> +	pcie {
> +		pinctrl_pcie_novena: pciegrp-novena {
> +			fsl,pins = <
> +				/* Reset */
> +				MX6QDL_PAD_EIM_D29__GPIO3_IO29  0x80000000
> +
> +				/* Power On */
> +				MX6QDL_PAD_GPIO_17__GPIO7_IO12  0x80000000
> +
> +				/* Wifi kill */
> +				MX6QDL_PAD_EIM_A22__GPIO2_IO16  0x80000000
> +			>;
> +		};
> +	};
> +
> +	sata {
> +		pinctrl_sata_novena: satagrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D30__GPIO3_IO30  0x80000000
> +			>;
> +		};
> +	};
> +
> +	senoko {
> +		pinctrl_senoko_novena: senokogrp-novena {
> +			fsl,pins = <
> +				/* Senoko IRQ line */
> +				MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048
> +
> +				/* Senoko reset line */
> +				MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x80000000
> +			>;
> +		};
> +	};
> +
> +	sound {
> +		pinctrl_sound_novena: soundgrp-novena {
> +			fsl,pins = <
> +				/* Audio power regulator */
> +				MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x80000000
> +
> +				/* Headphone plug */
> +				MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x80000000
> +
> +				MX6QDL_PAD_GPIO_0__CCM_CLKO1       0x80000000
> +			>;
> +		};
> +	};
> +
> +	ts {
> +		pinctrl_stmpe_novena: stmpegrp-novena {
> +			fsl,pins = <
> +				/* Touchscreen interrupt */
> +				MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x80000000
> +			>;
> +		};
> +	};
> +
> +	uart2 {
> +		pinctrl_uart2_novena: uart2grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D26__UART2_TX_DATA   0x1b0b1
> +				MX6QDL_PAD_EIM_D27__UART2_RX_DATA   0x1b0b1
> +			>;
> +		};
> +	};
> +
> +	uart3 {
> +		pinctrl_uart3_novena: uart3grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> +				MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> +			>;
> +		};
> +	};
> +	uart4 {
> +		pinctrl_uart4_novena: uart4grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
> +				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
> +			>;
> +		};
> +	};
> +
> +	usbotg {
> +		pinctrl_usbotg_novena: usbotggrp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> +			>;
> +		};
> +	};
> +
> +	usdhc2 {
> +		pinctrl_usdhc2_novena: usdhc2grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x170f9
> +				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x100f9
> +				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
> +				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
> +				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
> +				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
> +
> +				/* Write protect */
> +				MX6QDL_PAD_GPIO_2__GPIO1_IO02   0x80000000
> +
> +				/* Card detect */
> +				MX6QDL_PAD_GPIO_4__GPIO1_IO04   0x80000000
> +			>;
> +		};
> +	};
> +
> +	usdhc3 {
> +		pinctrl_usdhc3_novena: usdhc3grp-novena {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170f9
> +				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100f9
> +				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
> +				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
> +				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
> +				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
> +			>;
> +		};
> +	};
> +};
> +
> +&kpp {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_kpp_novena>;
> +	linux,keymap = <
> +		MATRIX_KEY(1, 1, KEY_CONFIG)
> +	>;
> +	status = "okay";
> +};
> +
> +&ldb {
> +	fsl,dual-channel;
> +	status = "okay";
> +	lvds-channel at 0 {
> +		fsl,data-mapping = "jeida";
> +		fsl,data-width = <24>;
> +		fsl,panel = <&panel>;
> +		status = "okay";
> +	};
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pcie_novena>;
> +	reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> +	bus-supply = <&reg_pcie>;

This isn't supported by the mainline binding. This needs more work to
properly handle PROBE_DEFER in the PCIe driver. Just remove this
property for now and make the regulator always-on, this will continue to
work when we come around to fixing this properly.

> +	status = "okay";
> +};
> +
> +&sata {
> +	target-supply = <&reg_sata>;
> +	fsl,transmit-level-mV = <1025>;
> +	fsl,transmit-boost-mdB = <0>;
> +	fsl,transmit-atten-16ths = <8>;
> +	status = "okay";
> +};
> +
> +&ssi1 {
> +	fsl,mode = "i2s-slave";
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2_novena>;
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3_novena>;
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4_novena>;
> +	status = "okay";
> +};
> +
> +&usbotg {
> +	vbus-supply = <&reg_usb_otg_vbus>;
> +	dr_mode = "otg";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg_novena>;
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	vbus-supply = <&swbst_reg>;
> +	status = "okay";
> +};
> +
> +&usdhc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2_novena>;
> +	cd-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;

I would bet this GPIO is actually ACTIVE_LOW, lots of boards got this
wrong initially.

> +	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&usdhc3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc3_novena>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +};

-- 
Pengutronix e.K.             | Lucas Stach                 |
Industrial Linux Solutions   | http://www.pengutronix.de/  |

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Wednesday, November 18, 2015 at 11:10:12 AM, Lucas Stach wrote:
> Hi Marek,

Hi!

> some comments below.

Thanks!

[...]

> > +	regulators {
> > +		compatible = "simple-bus";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> 
> Remove this simple bus. It's not there in hardware, regulators are board
> level components just like the nodes below.

This is surprising to me, since all the boards I checked use this /regulators
simple bus to contain all the regulators. Is this going to change now ?

> > +		reg_2p5v: 2p5v {
> > +			compatible = "regulator-fixed";
> > +			regulator-name = "2P5V";
> > +			regulator-min-microvolt = <2500000>;
> > +			regulator-max-microvolt = <2500000>;
> > +			regulator-always-on;
> > +		};
> > +
> > +		reg_3p3v: 3p3v {
> > +			compatible = "regulator-fixed";
> > +			regulator-name = "3P3V";
> > +			regulator-min-microvolt = <3300000>;
> > +			regulator-max-microvolt = <3300000>;
> > +			regulator-always-on;
> > +		};
> > +
> > +		reg_usb_otg_vbus: usb_otg_vbus {
> > +			compatible = "regulator-fixed";
> > +			regulator-name = "usb_otg_vbus";
> > +			regulator-min-microvolt = <5000000>;
> > +			regulator-max-microvolt = <5000000>;
> > +			enable-active-high;
> > +		};
> > +
> > +		reg_audio_codec: es8328-regulator {
> > +			compatible = "regulator-fixed";
> > +			regulator-name = "es8328-power";
> > +			regulator-boot-on;
> > +			regulator-min-microvolt = <5000000>;
> > +			regulator-max-microvolt = <5000000>;
> > +			startup-delay-us = <400000>;
> > +			gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
> > +			enable-active-high;
> > +		};
> > +
> > +		reg_pcie: pcie-regulator {
> > +			compatible = "regulator-fixed";
> > +			regulator-name = "pcie-bus-power";
> > +			regulator-min-microvolt = <1500000>;
> > +			regulator-max-microvolt = <1500000>;
> > +			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> > +			enable-active-high;
> 
> Make this an always-on regulator for now. More comments about this
> below.

Roger!

> > +		};

[...]

> > +&ecspi3 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_ecspi3_novena>;
> > +	fsl,spi-num-chipselects = <3>;
> > +	status = "okay";
> > +
> > +	spidev at 0 {
> > +		compatible = "spidev";
> 
> This will explode on a new kernel. Specifying spidev without using a
> more specific compatible will trigger a WARN_ON(), as it's considered
> bad style.

Oh, looks like imx_v6_v7_defconfig didn't have SPIDEV active, which is
why I didn't catch it during my last test, dang.

This SPI interface is routed into the FPGA, so what do you suggest I put
in the compatible string? There is no other sensible driver for the peripheral,
since the peripheral can be anything.

> > +		spi-max-frequency = <30000000>;
> > +		reg = <0>;
> > +	};
> > +};

[...]

> > +&pcie {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_pcie_novena>;
> > +	reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> > +	bus-supply = <&reg_pcie>;
> 
> This isn't supported by the mainline binding. This needs more work to
> properly handle PROBE_DEFER in the PCIe driver. Just remove this
> property for now and make the regulator always-on, this will continue to
> work when we come around to fixing this properly.

OK

> > +	status = "okay";
> > +};
> > +
> > +&sata {
> > +	target-supply = <&reg_sata>;
> > +	fsl,transmit-level-mV = <1025>;
> > +	fsl,transmit-boost-mdB = <0>;
> > +	fsl,transmit-atten-16ths = <8>;
> > +	status = "okay";
> > +};
> > +
> > +&ssi1 {
> > +	fsl,mode = "i2s-slave";
> > +	status = "okay";
> > +};
> > +
> > +&uart2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_uart2_novena>;
> > +	status = "okay";
> > +};
> > +
> > +&uart3 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_uart3_novena>;
> > +	status = "okay";
> > +};
> > +
> > +&uart4 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_uart4_novena>;
> > +	status = "okay";
> > +};
> > +
> > +&usbotg {
> > +	vbus-supply = <&reg_usb_otg_vbus>;
> > +	dr_mode = "otg";
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_usbotg_novena>;
> > +	disable-over-current;
> > +	status = "okay";
> > +};
> > +
> > +&usbh1 {
> > +	vbus-supply = <&swbst_reg>;
> > +	status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_usdhc2_novena>;
> > +	cd-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
> 
> I would bet this GPIO is actually ACTIVE_LOW, lots of boards got this
> wrong initially.

Both of them in fact are LOW, thanks!

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Lucas Stach]

Am Mittwoch, den 18.11.2015, 11:35 +0100 schrieb Marek Vasut:
> On Wednesday, November 18, 2015 at 11:10:12 AM, Lucas Stach wrote:
> > Hi Marek,
> 
> Hi!
> 
> > some comments below.
> 
> Thanks!
> 
> [...]
> 
> > > +	regulators {
> > > +		compatible = "simple-bus";
> > > +		#address-cells = <1>;
> > > +		#size-cells = <0>;
> > > +
> > 
> > Remove this simple bus. It's not there in hardware, regulators are board
> > level components just like the nodes below.
> 
> This is surprising to me, since all the boards I checked use this /regulators
> simple bus to contain all the regulators. Is this going to change now ?

Yes, there are a lot of bad examples out there, mainly because people
wanted to logically group the regulators together. But as it isn't
representing any real hardware we should really try to move away from
this practice.

> [...]
> 
> > > +&ecspi3 {
> > > +	pinctrl-names = "default";
> > > +	pinctrl-0 = <&pinctrl_ecspi3_novena>;
> > > +	fsl,spi-num-chipselects = <3>;
> > > +	status = "okay";
> > > +
> > > +	spidev at 0 {
> > > +		compatible = "spidev";
> > 
> > This will explode on a new kernel. Specifying spidev without using a
> > more specific compatible will trigger a WARN_ON(), as it's considered
> > bad style.
> 
> Oh, looks like imx_v6_v7_defconfig didn't have SPIDEV active, which is
> why I didn't catch it during my last test, dang.
> 
> This SPI interface is routed into the FPGA, so what do you suggest I put
> in the compatible string? There is no other sensible driver for the peripheral,
> since the peripheral can be anything.
> 
I'm not really the right person to ask for that, but I would guess that
inventing a "novena,fpga-spi" compatible or something like that and
adding it to the spidev driver would be the right thing to do.

Regards,
Lucas

-- 
Pengutronix e.K.             | Lucas Stach                 |
Industrial Linux Solutions   | http://www.pengutronix.de/  |

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Wednesday, November 18, 2015 at 12:25:58 PM, Lucas Stach wrote:
> Am Mittwoch, den 18.11.2015, 11:35 +0100 schrieb Marek Vasut:
> > On Wednesday, November 18, 2015 at 11:10:12 AM, Lucas Stach wrote:
> > > Hi Marek,
> > 
> > Hi!
> > 
> > > some comments below.
> > 
> > Thanks!
> > 
> > [...]
> > 
> > > > +	regulators {
> > > > +		compatible = "simple-bus";
> > > > +		#address-cells = <1>;
> > > > +		#size-cells = <0>;
> > > > +
> > > 
> > > Remove this simple bus. It's not there in hardware, regulators are
> > > board level components just like the nodes below.
> > 
> > This is surprising to me, since all the boards I checked use this
> > /regulators simple bus to contain all the regulators. Is this going to
> > change now ?
> 
> Yes, there are a lot of bad examples out there, mainly because people
> wanted to logically group the regulators together.

Yeah, that's what I wanted to do as well :)

> But as it isn't
> representing any real hardware we should really try to move away from
> this practice.

Oh, thanks for this input.

> > [...]
> > 
> > > > +&ecspi3 {
> > > > +	pinctrl-names = "default";
> > > > +	pinctrl-0 = <&pinctrl_ecspi3_novena>;
> > > > +	fsl,spi-num-chipselects = <3>;
> > > > +	status = "okay";
> > > > +
> > > > +	spidev at 0 {
> > > > +		compatible = "spidev";
> > > 
> > > This will explode on a new kernel. Specifying spidev without using a
> > > more specific compatible will trigger a WARN_ON(), as it's considered
> > > bad style.
> > 
> > Oh, looks like imx_v6_v7_defconfig didn't have SPIDEV active, which is
> > why I didn't catch it during my last test, dang.
> > 
> > This SPI interface is routed into the FPGA, so what do you suggest I put
> > in the compatible string? There is no other sensible driver for the
> > peripheral, since the peripheral can be anything.
> 
> I'm not really the right person to ask for that, but I would guess that
> inventing a "novena,fpga-spi" compatible or something like that and
> adding it to the spidev driver would be the right thing to do.

So what's the rationale behind generic "spidev" being bad ? In my mind, it
is much better to use generic driver and generic compatible prop "spidev"
than to generate many one-off compatible props and have a driver with a list
of all of those.

Best regards,
Marek Vasut

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Lucas Stach]

Am Mittwoch, den 18.11.2015, 12:32 +0100 schrieb Marek Vasut:
> On Wednesday, November 18, 2015 at 12:25:58 PM, Lucas Stach wrote:
> > Am Mittwoch, den 18.11.2015, 11:35 +0100 schrieb Marek Vasut:
> > > On Wednesday, November 18, 2015 at 11:10:12 AM, Lucas Stach wrote:
> > > > Hi Marek,
[...]
> > > [...]
> > > 
> > > > > +&ecspi3 {
> > > > > +	pinctrl-names = "default";
> > > > > +	pinctrl-0 = <&pinctrl_ecspi3_novena>;
> > > > > +	fsl,spi-num-chipselects = <3>;
> > > > > +	status = "okay";
> > > > > +
> > > > > +	spidev at 0 {
> > > > > +		compatible = "spidev";
> > > > 
> > > > This will explode on a new kernel. Specifying spidev without using a
> > > > more specific compatible will trigger a WARN_ON(), as it's considered
> > > > bad style.
> > > 
> > > Oh, looks like imx_v6_v7_defconfig didn't have SPIDEV active, which is
> > > why I didn't catch it during my last test, dang.
> > > 
> > > This SPI interface is routed into the FPGA, so what do you suggest I put
> > > in the compatible string? There is no other sensible driver for the
> > > peripheral, since the peripheral can be anything.
> > 
> > I'm not really the right person to ask for that, but I would guess that
> > inventing a "novena,fpga-spi" compatible or something like that and
> > adding it to the spidev driver would be the right thing to do.
> 
> So what's the rationale behind generic "spidev" being bad ? In my mind, it
> is much better to use generic driver and generic compatible prop "spidev"
> than to generate many one-off compatible props and have a driver with a list
> of all of those.
> 
>From the commit log:

"Since spidev is a detail of how Linux controls a device rather than a
description of the hardware in the system we should never have a node
described as "spidev" in DT, any SPI device could be a spidev so this is
just not a useful description."

If you want to know about the details you would have to discuss this
with Mark Brown.

Regards,
Lucas

-- 
Pengutronix e.K.             | Lucas Stach                 |
Industrial Linux Solutions   | http://www.pengutronix.de/  |

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Wednesday, November 18, 2015 at 12:36:16 PM, Lucas Stach wrote:
> Am Mittwoch, den 18.11.2015, 12:32 +0100 schrieb Marek Vasut:
> > On Wednesday, November 18, 2015 at 12:25:58 PM, Lucas Stach wrote:
> > > Am Mittwoch, den 18.11.2015, 11:35 +0100 schrieb Marek Vasut:
> > > > On Wednesday, November 18, 2015 at 11:10:12 AM, Lucas Stach wrote:
> > > > > Hi Marek,
> 
> [...]
> 
> > > > [...]
> > > > 
> > > > > > +&ecspi3 {
> > > > > > +	pinctrl-names = "default";
> > > > > > +	pinctrl-0 = <&pinctrl_ecspi3_novena>;
> > > > > > +	fsl,spi-num-chipselects = <3>;
> > > > > > +	status = "okay";
> > > > > > +
> > > > > > +	spidev at 0 {
> > > > > > +		compatible = "spidev";
> > > > > 
> > > > > This will explode on a new kernel. Specifying spidev without using
> > > > > a more specific compatible will trigger a WARN_ON(), as it's
> > > > > considered bad style.
> > > > 
> > > > Oh, looks like imx_v6_v7_defconfig didn't have SPIDEV active, which
> > > > is why I didn't catch it during my last test, dang.
> > > > 
> > > > This SPI interface is routed into the FPGA, so what do you suggest I
> > > > put in the compatible string? There is no other sensible driver for
> > > > the peripheral, since the peripheral can be anything.
> > > 
> > > I'm not really the right person to ask for that, but I would guess that
> > > inventing a "novena,fpga-spi" compatible or something like that and
> > > adding it to the spidev driver would be the right thing to do.
> > 
> > So what's the rationale behind generic "spidev" being bad ? In my mind,
> > it is much better to use generic driver and generic compatible prop
> > "spidev" than to generate many one-off compatible props and have a
> > driver with a list of all of those.
> 
> From the commit log:
> 
> "Since spidev is a detail of how Linux controls a device rather than a
> description of the hardware in the system we should never have a node
> described as "spidev" in DT, any SPI device could be a spidev so this is
> just not a useful description."
> 
> If you want to know about the details you would have to discuss this
> with Mark Brown.

I see, thanks for the clarification. I think I will drop this spidev for
now and add it once/if it's really needed. I think this might be much
better than poluting the spidev driver with yet another compat string.
What do you say ?

Best regards,
Marek Vasut

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Fabio Estevam]

On Wed, Nov 18, 2015 at 9:25 AM, Lucas Stach <l.stach@pengutronix.de> wrote:

>> This is surprising to me, since all the boards I checked use this /regulators
>> simple bus to contain all the regulators. Is this going to change now ?
>
> Yes, there are a lot of bad examples out there, mainly because people
> wanted to logically group the regulators together. But as it isn't
> representing any real hardware we should really try to move away from
> this practice.

Agreed.

I have tried to fixing this usage on sabresd board:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/231934.html

,and there was some discussions whether this was churn or not, so I
ended up not resending it.

IMHO we should make this consistent in the various dts files.

Regards,

Fabio Estevam

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Fabio Estevam]

Hi Marek,

On Wed, Nov 18, 2015 at 7:48 AM, Marek Vasut <marex@denx.de> wrote:

> +++ b/arch/arm/boot/dts/imx6q-novena.dts
> @@ -0,0 +1,825 @@
> +/*
> + * Copyright 2014 Sutajio Ko-Usagi PTE LTD
> + * Copyright 2012 Freescale Semiconductor, Inc.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html

Could you make this GPL/X11 dual-license?

Take a look at arch/arm/boot/dts/imx6qdl-cubox-i.dtsi for a reference.

> +&iomuxc {
> +       audmux {
> +               pinctrl_audmux_novena: audmuxgrp-novena {
> +                       fsl,pins = <
> +                               MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x80000000
> +                               MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x80000000
> +                               MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x80000000
> +                               MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000

Please avoid these 0x80000000 throughout this file.

We should better not rely on the IOMUX settings done in the bootloader.

Regards,

Fabio Estevam

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Wednesday, November 18, 2015 at 01:00:50 PM, Fabio Estevam wrote:
> Hi Marek,

Hi!

> On Wed, Nov 18, 2015 at 7:48 AM, Marek Vasut <marex@denx.de> wrote:
> > +++ b/arch/arm/boot/dts/imx6q-novena.dts
> > @@ -0,0 +1,825 @@
> > +/*
> > + * Copyright 2014 Sutajio Ko-Usagi PTE LTD
> > + * Copyright 2012 Freescale Semiconductor, Inc.
> > + * Copyright 2011 Linaro Ltd.
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> 
> Could you make this GPL/X11 dual-license?

I'll talk to Sean about this, but I hope this is not a problem.

> Take a look at arch/arm/boot/dts/imx6qdl-cubox-i.dtsi for a reference.
> 
> > +&iomuxc {
> > +       audmux {
> > +               pinctrl_audmux_novena: audmuxgrp-novena {
> > +                       fsl,pins = <
> > +                               MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 
> > 0x80000000 +                              
> > MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x80000000 +                            
> >   MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x80000000 +                          
> >     MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000
> 
> Please avoid these 0x80000000 throughout this file.
> 
> We should better not rely on the IOMUX settings done in the bootloader.

Fixed, thanks!

Best regards,
Marek Vasut

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Sean Cross]

On 20/11/2015 12:11 AM, Marek Vasut wrote:
> On Wednesday, November 18, 2015 at 01:00:50 PM, Fabio Estevam wrote:
>> Hi Marek,
> Hi!
>
>> On Wed, Nov 18, 2015 at 7:48 AM, Marek Vasut <marex@denx.de> wrote:
>>> +++ b/arch/arm/boot/dts/imx6q-novena.dts
>>> @@ -0,0 +1,825 @@
>>> +/*
>>> + * Copyright 2014 Sutajio Ko-Usagi PTE LTD
>>> + * Copyright 2012 Freescale Semiconductor, Inc.
>>> + * Copyright 2011 Linaro Ltd.
>>> + *
>>> + * The code contained herein is licensed under the GNU General Public
>>> + * License. You may obtain a copy of the GNU General Public License
>>> + * Version 2 or later at the following locations:
>>> + *
>>> + * http://www.opensource.org/licenses/gpl-license.html
>>> + * http://www.gnu.org/copyleft/gpl.html
>> Could you make this GPL/X11 dual-license?
> I'll talk to Sean about this, but I hope this is not a problem.
The licensing change to dual-license is fine by me.


Sean

[PATCH 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Friday, November 20, 2015 at 03:49:30 AM, Sean Cross wrote:
> On 20/11/2015 12:11 AM, Marek Vasut wrote:
> > On Wednesday, November 18, 2015 at 01:00:50 PM, Fabio Estevam wrote:
> >> Hi Marek,
> > 
> > Hi!
> > 
> >> On Wed, Nov 18, 2015 at 7:48 AM, Marek Vasut <marex@denx.de> wrote:
> >>> +++ b/arch/arm/boot/dts/imx6q-novena.dts
> >>> @@ -0,0 +1,825 @@
> >>> +/*
> >>> + * Copyright 2014 Sutajio Ko-Usagi PTE LTD
> >>> + * Copyright 2012 Freescale Semiconductor, Inc.
> >>> + * Copyright 2011 Linaro Ltd.
> >>> + *
> >>> + * The code contained herein is licensed under the GNU General Public
> >>> + * License. You may obtain a copy of the GNU General Public License
> >>> + * Version 2 or later at the following locations:
> >>> + *
> >>> + * http://www.opensource.org/licenses/gpl-license.html
> >>> + * http://www.gnu.org/copyleft/gpl.html
> >> 
> >> Could you make this GPL/X11 dual-license?
> > 
> > I'll talk to Sean about this, but I hope this is not a problem.
> 
> The licensing change to dual-license is fine by me.

Thanks!

Best regards,
Marek Vasut

[PATCH V2 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

From: Sean Cross <xobs@kosagi.com>

Novena is an open-hardware laptop/desktop/bare board.

See http://www.kosagi.com/w/index.php?title=Novena_Main_Page

Signed-off-by: Sean Cross <xobs@kosagi.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Shawn Guo <shawnguo@kernel.org>
---
 arch/arm/boot/dts/Makefile         |   1 +
 arch/arm/boot/dts/imx6q-novena.dts | 856 +++++++++++++++++++++++++++++++++++++
 2 files changed, 857 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-novena.dts

V2: Fix the PCIe regulator, make it always on
    Fix the polarity of SD2 WP and CD lines, make them active low.
    Drop the simple-bus for regulators, put them in /soc instead.
    Configure the mux of all pins instead of depending on bootloader.
    Change license to Dual X11/GPLv2+ (Acked by Sean)
    Sort the nodes alphabetically.

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e5136e1..cec492d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-hummingboard.dtb \
 	imx6q-nitrogen6x.dtb \
 	imx6q-nitrogen6_max.dtb \
+	imx6q-novena.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-rex-pro.dtb \
 	imx6q-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts
new file mode 100644
index 0000000..951bfeda
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-novena.dts
@@ -0,0 +1,856 @@
+/*
+ * Copyright 2015 Sutajio Ko-Usagi PTE LTD
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Kosagi Novena Dual/Quad";
+	compatible = "kosagi,imx6q-novena", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0xefffffff>;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 10000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_novena>;
+		power-supply = <&reg_lvds_lcd>;
+
+		brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>;
+		default-brightness-level = <12>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys_novena>;
+
+		user-button {
+			label = "User Button";
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		lid {
+			label = "Lid";
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,input-type = <5>;	/* EV_SW */
+			linux,code = <0>;	/* SW_LID */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_novena>;
+
+		heartbeat {
+			label = "novena:white:panel";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	panel: panel {
+		compatible = "innolux,n133hse-ea1", "simple-panel";
+		backlight = <&backlight>;
+	};
+
+	soc {
+		reg_2p5v: 2p5v {
+			compatible = "regulator-fixed";
+			regulator-name = "2P5V";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			regulator-always-on;
+		};
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usb_otg_vbus: usb_otg_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+		};
+
+		reg_audio_codec: es8328-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "es8328-power";
+			regulator-boot-on;
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <400000>;
+			gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_pcie: pcie-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "pcie-bus-power";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			regulator-always-on;
+		};
+
+		reg_lvds_lcd: lcd-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-lvds-power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_display: display-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "lcd-display-power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			startup-delay-us = <200000>;
+			gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_sata: sata-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "sata-power";
+			regulator-boot-on;
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			startup-delay-us = <10000>;
+			gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-es8328";
+		model = "imx-audio-es8328";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-amp-supply = <&reg_audio_codec>;
+		jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>;
+		audio-routing =
+			"Speaker", "LOUT2",
+			"Speaker", "ROUT2",
+			"Speaker", "audio-amp",
+			"Headphone", "ROUT1",
+			"Headphone", "LOUT1",
+			"LINPUT1", "Mic Jack",
+			"RINPUT1", "Mic Jack",
+			"Mic Jack", "Mic Bias";
+		mux-int-port = <0x1>;
+		mux-ext-port = <0x3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_novena>;
+	status = "okay";
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3_novena>;
+	fsl,spi-num-chipselects = <3>;
+	status = "okay";
+
+	spidev at 0 {
+		compatible = "spidev";
+		spi-max-frequency = <30000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_novena>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+	mac-address = [00 00 00 00 00 00];
+	rxc-skew-ps = <3000>;
+	rxdv-skew-ps = <0>;
+	txc-skew-ps = <3000>;
+	txen-skew-ps = <0>;
+	rxd0-skew-ps = <0>;
+	rxd1-skew-ps = <0>;
+	rxd2-skew-ps = <0>;
+	rxd3-skew-ps = <0>;
+	txd0-skew-ps = <3000>;
+	txd1-skew-ps = <3000>;
+	txd2-skew-ps = <3000>;
+	txd3-skew-ps = <3000>;
+	status = "okay";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_novena>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_novena>;
+	status = "okay";
+
+	accel: mma8452 at 1c {
+		compatible = "fsl,mma8452";
+		reg = <0x1c>;
+	};
+
+	rtc: pcf8523 at 68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+
+	sbs_battery: bq20z75 at 0b {
+		compatible = "sbs,sbs-battery";
+		reg = <0x0b>;
+		sbs,i2c-retry-count = <50>;
+	};
+
+	touch: stmpe811 at 44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		id = <0>;
+		blocks = <0x5>;
+		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe_novena>;
+		vio-supply = <&reg_3p3v>;
+		vcc-supply = <&reg_3p3v>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2_novena>;
+	status = "okay";
+
+	pmic: pfuze100 at 08 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_novena>;
+	status = "okay";
+
+	codec: es8328 at 11 {
+		compatible = "everest,es8328";
+		reg = <0x11>;
+		DVDD-supply = <&reg_audio_codec>;
+		AVDD-supply = <&reg_audio_codec>;
+		PVDD-supply = <&reg_audio_codec>;
+		HPVDD-supply = <&reg_audio_codec>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sound_novena>;
+
+		clocks = <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>, <&clks IMX6QDL_CLK_CKO1_SEL>, <&clks IMX6QDL_CLK_PLL4_AUDIO>, <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_CKO1_PODF>;
+		assigned-clock-rates = <0 0 722534400 22579200>;
+	};
+};
+
+&iomuxc {
+	audmux {
+		pinctrl_audmux_novena: audmuxgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			>;
+		};
+	};
+
+	backlight {
+		pinctrl_backlight_novena: backlightgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b0
+				MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28	0x1b0b1
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b1
+			>;
+		};
+	};
+
+	ecspi3 {
+		pinctrl_ecspi3_novena: ecspi3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			>;
+		};
+	};
+
+	enet {
+		pinctrl_enet_novena: enetgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b028
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b028
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b028
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b028
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b028
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+
+				/* Ethernet reset */
+				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b1
+			>;
+		};
+	};
+
+	fpga {
+		pinctrl_fpga_gpio: fpgagpiogrp-novena {
+			fsl,pins = <
+				/* FPGA power */
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
+
+				/* Reset */
+				MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07	0x1b0b1
+
+				/* FPGA GPIOs */
+				MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0x1b0b1
+				MX6QDL_PAD_EIM_DA1__GPIO3_IO01		0x1b0b1
+				MX6QDL_PAD_EIM_DA2__GPIO3_IO02		0x1b0b1
+				MX6QDL_PAD_EIM_DA3__GPIO3_IO03		0x1b0b1
+				MX6QDL_PAD_EIM_DA4__GPIO3_IO04		0x1b0b1
+				MX6QDL_PAD_EIM_DA5__GPIO3_IO05		0x1b0b1
+				MX6QDL_PAD_EIM_DA6__GPIO3_IO06		0x1b0b1
+				MX6QDL_PAD_EIM_DA7__GPIO3_IO07		0x1b0b1
+				MX6QDL_PAD_EIM_DA8__GPIO3_IO08		0x1b0b1
+				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x1b0b1
+				MX6QDL_PAD_EIM_DA10__GPIO3_IO10		0x1b0b1
+				MX6QDL_PAD_EIM_DA11__GPIO3_IO11		0x1b0b1
+				MX6QDL_PAD_EIM_DA12__GPIO3_IO12		0x1b0b1
+				MX6QDL_PAD_EIM_DA13__GPIO3_IO13		0x1b0b1
+				MX6QDL_PAD_EIM_DA14__GPIO3_IO14		0x1b0b1
+				MX6QDL_PAD_EIM_DA15__GPIO3_IO15		0x1b0b1
+				MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x1b0b1
+				MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x1b0b1
+				MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x1b0b1
+				MX6QDL_PAD_EIM_CS0__GPIO2_IO23		0x1b0b1
+				MX6QDL_PAD_EIM_CS1__GPIO2_IO24		0x1b0b1
+				MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x1b0b1
+				MX6QDL_PAD_EIM_OE__GPIO2_IO25		0x1b0b1
+				MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x1b0b1
+				MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x1b0b1
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b1
+			>;
+		};
+
+		pinctrl_fpga_eim: fpgaeimgrp-novena {
+			fsl,pins = <
+				/* FPGA power */
+				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
+
+				/* Reset */
+				MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07	0x1b0b1
+
+				/* FPGA GPIOs */
+				MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0f1
+				MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0f1
+				MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0f1
+				MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0f1
+				MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0f1
+				MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0f1
+				MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0f1
+				MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0f1
+				MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0f1
+				MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0f1
+				MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0f1
+				MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0f1
+				MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0f1
+				MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0f1
+				MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0f1
+				MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0f1
+				MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0f1
+				MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0f1
+				MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0f1
+				MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0f1
+				MX6QDL_PAD_EIM_CS1__EIM_CS1_B		0xb0f1
+				MX6QDL_PAD_EIM_LBA__EIM_LBA_B		0xb0f1
+				MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0f1
+				MX6QDL_PAD_EIM_RW__EIM_RW		0xb0f1
+				MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B		0xb0f1
+				MX6QDL_PAD_EIM_BCLK__EIM_BCLK		0xb0f1
+			>;
+		};
+	};
+
+	gpio_keys {
+		pinctrl_gpio_keys_novena: gpiokeysgrp-novena {
+			fsl,pins = <
+				/* User button */
+				MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+
+				/* PCIe Wakeup */
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1f0e0
+
+				/* Lid switch */
+				MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0
+			>;
+		};
+	};
+
+	hdmi {
+		pinctrl_hdmi_novena: hdmigrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+				MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b0b1
+			>;
+		};
+	};
+
+	i2c1 {
+		pinctrl_i2c1_novena: i2c1grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			>;
+		};
+	};
+
+	i2c2 {
+		pinctrl_i2c2_novena: i2c2grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+				MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
+			>;
+		};
+	};
+
+	i2c3 {
+		pinctrl_i2c3_novena: i2c3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+				MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
+			>;
+		};
+	};
+
+	kpp-keys {
+		pinctrl_kpp_novena: kppgrp-novena {
+			fsl,pins = <
+				/* Front panel button */
+				MX6QDL_PAD_KEY_ROW1__KEY_ROW1		0x1b0b1
+
+				/* Fake column driver, not connected */
+				MX6QDL_PAD_KEY_COL1__KEY_COL1		0x1b0b1
+			>;
+		};
+	};
+
+	leds {
+		pinctrl_leds_novena: ledsgrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT3__GPIO1_IO21		0x1b0b1
+			>;
+		};
+	};
+
+	pcie {
+		pinctrl_pcie_novena: pciegrp-novena {
+			fsl,pins = <
+				/* Reset */
+				MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x1b0b1
+
+				/* Power On */
+				MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b1
+
+				/* Wifi kill */
+				MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x1b0b1
+			>;
+		};
+	};
+
+	sata {
+		pinctrl_sata_novena: satagrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b1
+			>;
+		};
+	};
+
+	senoko {
+		pinctrl_senoko_novena: senokogrp-novena {
+			fsl,pins = <
+				/* Senoko IRQ line */
+				MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x13048
+
+				/* Senoko reset line */
+				MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x1b0b1
+			>;
+		};
+	};
+
+	sound {
+		pinctrl_sound_novena: soundgrp-novena {
+			fsl,pins = <
+				/* Audio power regulator */
+				MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b1
+
+				/* Headphone plug */
+				MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b1
+
+				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
+			>;
+		};
+	};
+
+	ts {
+		pinctrl_stmpe_novena: stmpegrp-novena {
+			fsl,pins = <
+				/* Touchscreen interrupt */
+				MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b1
+			>;
+		};
+	};
+
+	uart2 {
+		pinctrl_uart2_novena: uart2grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+			>;
+		};
+	};
+
+	uart3 {
+		pinctrl_uart3_novena: uart3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			>;
+		};
+	};
+	uart4 {
+		pinctrl_uart4_novena: uart4grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+			>;
+		};
+	};
+
+	usbotg {
+		pinctrl_usbotg_novena: usbotggrp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+			>;
+		};
+	};
+
+	usdhc2 {
+		pinctrl_usdhc2_novena: usdhc2grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+
+				/* Write protect */
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b1
+
+				/* Card detect */
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b1
+			>;
+		};
+	};
+
+	usdhc3 {
+		pinctrl_usdhc3_novena: usdhc3grp-novena {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
+				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+			>;
+		};
+	};
+};
+
+&kpp {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_kpp_novena>;
+	linux,keymap = <
+		MATRIX_KEY(1, 1, KEY_CONFIG)
+	>;
+	status = "okay";
+};
+
+&ldb {
+	fsl,dual-channel;
+	status = "okay";
+	lvds-channel at 0 {
+		fsl,data-mapping = "jeida";
+		fsl,data-width = <24>;
+		fsl,panel = <&panel>;
+		status = "okay";
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie_novena>;
+	reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&sata {
+	target-supply = <&reg_sata>;
+	fsl,transmit-level-mV = <1025>;
+	fsl,transmit-boost-mdB = <0>;
+	fsl,transmit-atten-16ths = <8>;
+	status = "okay";
+};
+
+&ssi1 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_novena>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_novena>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4_novena>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg_novena>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&swbst_reg>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_novena>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_novena>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
-- 
2.1.4

[PATCH V2 2/2] ARM: dts: imx6q: add Novena board

[Fabio Estevam]

On Fri, Nov 20, 2015 at 6:46 PM, Marek Vasut <marex@denx.de> wrote:
> From: Sean Cross <xobs@kosagi.com>
>
> Novena is an open-hardware laptop/desktop/bare board.
>
> See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
>
> Signed-off-by: Sean Cross <xobs@kosagi.com>
> Cc: Fabio Estevam <fabio.estevam@freescale.com>
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Cc: Sean Cross <xobs@kosagi.com>
> Cc: Shawn Guo <shawnguo@kernel.org>

Looks good:
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Two minor comments:

> +&fec {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_enet_novena>;
> +       phy-mode = "rgmii";
> +       phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
> +       mac-address = [00 00 00 00 00 00];

This mac-address entry could be removed, right?

> +&ssi1 {
> +       fsl,mode = "i2s-slave";

Please remove this one. It is no longer used.

[PATCH V2 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Friday, November 20, 2015 at 09:58:39 PM, Fabio Estevam wrote:
> On Fri, Nov 20, 2015 at 6:46 PM, Marek Vasut <marex@denx.de> wrote:
> > From: Sean Cross <xobs@kosagi.com>
> > 
> > Novena is an open-hardware laptop/desktop/bare board.
> > 
> > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
> > 
> > Signed-off-by: Sean Cross <xobs@kosagi.com>
> > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> > Cc: Lucas Stach <l.stach@pengutronix.de>
> > Cc: Sean Cross <xobs@kosagi.com>
> > Cc: Shawn Guo <shawnguo@kernel.org>
> 
> Looks good:
> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
> 
> Two minor comments:
> > +&fec {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_enet_novena>;
> > +       phy-mode = "rgmii";
> > +       phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
> > +       mac-address = [00 00 00 00 00 00];
> 
> This mac-address entry could be removed, right?
> 
> > +&ssi1 {
> > +       fsl,mode = "i2s-slave";
> 
> Please remove this one. It is no longer used.

Yeah, and I should've dropped the spidev node altogether.

Best regards,
Marek Vasut

[PATCH V2 2/2] ARM: dts: imx6q: add Novena board

[Lucas Stach]

Am Freitag, den 20.11.2015, 21:46 +0100 schrieb Marek Vasut:
> From: Sean Cross <xobs@kosagi.com>
> 
> Novena is an open-hardware laptop/desktop/bare board.
> 
> See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
> 
> Signed-off-by: Sean Cross <xobs@kosagi.com>
> Cc: Fabio Estevam <fabio.estevam@freescale.com>
> Cc: Lucas Stach <l.stach@pengutronix.de>
> Cc: Sean Cross <xobs@kosagi.com>
> Cc: Shawn Guo <shawnguo@kernel.org>
> ---
>  arch/arm/boot/dts/Makefile         |   1 +
>  arch/arm/boot/dts/imx6q-novena.dts | 856 +++++++++++++++++++++++++++++++++++++
>  2 files changed, 857 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-novena.dts
> 
> V2: Fix the PCIe regulator, make it always on
>     Fix the polarity of SD2 WP and CD lines, make them active low.
>     Drop the simple-bus for regulators, put them in /soc instead.

Huh? No. The fixed and GPIO controlled regulators are certainly not part
of the SoC. They are board level components and belong into the same DT
hierarchy level as the sound codec and leds.

Otherwise looks good now.

Regards,
Lucas

-- 
Pengutronix e.K.             | Lucas Stach                 |
Industrial Linux Solutions   | http://www.pengutronix.de/  |

[PATCH V2 2/2] ARM: dts: imx6q: add Novena board

[Marek Vasut]

On Monday, November 23, 2015 at 10:15:24 AM, Lucas Stach wrote:
> Am Freitag, den 20.11.2015, 21:46 +0100 schrieb Marek Vasut:
> > From: Sean Cross <xobs@kosagi.com>
> > 
> > Novena is an open-hardware laptop/desktop/bare board.
> > 
> > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page
> > 
> > Signed-off-by: Sean Cross <xobs@kosagi.com>
> > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> > Cc: Lucas Stach <l.stach@pengutronix.de>
> > Cc: Sean Cross <xobs@kosagi.com>
> > Cc: Shawn Guo <shawnguo@kernel.org>
> > ---
> > 
> >  arch/arm/boot/dts/Makefile         |   1 +
> >  arch/arm/boot/dts/imx6q-novena.dts | 856
> >  +++++++++++++++++++++++++++++++++++++ 2 files changed, 857
> >  insertions(+)
> >  create mode 100644 arch/arm/boot/dts/imx6q-novena.dts
> > 
> > V2: Fix the PCIe regulator, make it always on
> > 
> >     Fix the polarity of SD2 WP and CD lines, make them active low.
> >     Drop the simple-bus for regulators, put them in /soc instead.
> 
> Huh? No. The fixed and GPIO controlled regulators are certainly not part
> of the SoC. They are board level components and belong into the same DT
> hierarchy level as the sound codec and leds.

Huh? When I did that with 4.4rc1, the regulators were not detected, but with
4.4rc2 they are. Must've been some instability at that point of development
cycle. I will test this some more and then send a V3.

Thanks for the help :)

> Otherwise looks good now.
> 
> Regards,
> Lucas

Best regards,
Marek Vasut

[PATCH 1/2] devicetree: bindings: Add vendor prefix for Kosagi

[Arnd Bergmann]

On Wednesday 18 November 2015 10:48:39 Marek Vasut wrote:
> From: Sean Cross <xobs@kosagi.com>
> 
> Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the
> more common name of Kosagi.
> 
> Signed-off-by: Sean Cross <xobs@kosagi.com>
> Cc: Rob Herring <robh@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Fabio Estevam <fabio.estevam@freescale.com>
> 

Hi Marek,

you forgot to add your Signed-off-by line on both of these patches.

	Arnd

[PATCH 1/2] devicetree: bindings: Add vendor prefix for Kosagi

[Marek Vasut]

On Friday, November 20, 2015 at 10:19:15 PM, Arnd Bergmann wrote:
> On Wednesday 18 November 2015 10:48:39 Marek Vasut wrote:
> > From: Sean Cross <xobs@kosagi.com>
> > 
> > Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the
> > more common name of Kosagi.
> > 
> > Signed-off-by: Sean Cross <xobs@kosagi.com>
> > Cc: Rob Herring <robh@kernel.org>
> > Cc: Shawn Guo <shawnguo@kernel.org>
> > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> 
> Hi Marek,

Hi!

> you forgot to add your Signed-off-by line on both of these patches.

I should probably re-post the 2/2 anyway, but if you want to pick this
1/2 patch right away, please just add:

Signed-off-by: Marek Vasut <marex@denx.de>

In case you want me to repost them, please let me know.

Best regards,
Marek Vasut

[PATCH 1/2] devicetree: bindings: Add vendor prefix for Kosagi

[Arnd Bergmann]

On Friday 20 November 2015 23:30:39 Marek Vasut wrote:
> On Friday, November 20, 2015 at 10:19:15 PM, Arnd Bergmann wrote:
> > On Wednesday 18 November 2015 10:48:39 Marek Vasut wrote:
> > > From: Sean Cross <xobs@kosagi.com>
> > > 
> > > Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the
> > > more common name of Kosagi.
> > > 
> > > Signed-off-by: Sean Cross <xobs@kosagi.com>
> > > Cc: Rob Herring <robh@kernel.org>
> > > Cc: Shawn Guo <shawnguo@kernel.org>
> > > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> > 
> > Hi Marek,
> 
> Hi!
> 
> > you forgot to add your Signed-off-by line on both of these patches.
> 
> I should probably re-post the 2/2 anyway, but if you want to pick this
> 1/2 patch right away, please just add:
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> 
> In case you want me to repost them, please let me know.

I wasn't planning to pick them up, I think they should go through the imx
tree, so just repost them as a series.

	Arnd

[PATCH 1/2] devicetree: bindings: Add vendor prefix for Kosagi

[Marek Vasut]

On Friday, November 20, 2015 at 11:46:02 PM, Arnd Bergmann wrote:
> On Friday 20 November 2015 23:30:39 Marek Vasut wrote:
> > On Friday, November 20, 2015 at 10:19:15 PM, Arnd Bergmann wrote:
> > > On Wednesday 18 November 2015 10:48:39 Marek Vasut wrote:
> > > > From: Sean Cross <xobs@kosagi.com>
> > > > 
> > > > Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the
> > > > more common name of Kosagi.
> > > > 
> > > > Signed-off-by: Sean Cross <xobs@kosagi.com>
> > > > Cc: Rob Herring <robh@kernel.org>
> > > > Cc: Shawn Guo <shawnguo@kernel.org>
> > > > Cc: Fabio Estevam <fabio.estevam@freescale.com>
> > > 
> > > Hi Marek,
> > 
> > Hi!
> > 
> > > you forgot to add your Signed-off-by line on both of these patches.
> > 
> > I should probably re-post the 2/2 anyway, but if you want to pick this
> > 1/2 patch right away, please just add:
> > 
> > Signed-off-by: Marek Vasut <marex@denx.de>
> > 
> > In case you want me to repost them, please let me know.
> 
> I wasn't planning to pick them up, I think they should go through the imx
> tree, so just repost them as a series.

Roger, will do.

Thanks!

Best regards,
Marek Vasut