From: wens@csie.org (Chen-Yu Tsai)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 5/6] ARM: dts: sun8i: sinlinx-sina33: Add AXP223 PMIC device and regulator nodes
Date: Tue, 24 Nov 2015 11:48:35 +0800 [thread overview]
Message-ID: <1448336916-31212-6-git-send-email-wens@csie.org> (raw)
In-Reply-To: <1448336916-31212-1-git-send-email-wens@csie.org>
This board has a X-Powers AXP223 PMIC connected via RSB. Its regulators
provide power to various parts of the SoC and the board.
Also update the regulator supply phandles.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts | 79 +++++++++++++++++++++++++-
1 file changed, 76 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts
index 13ce68f06dd6..91a0fde47fdd 100644
--- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts
+++ b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts
@@ -68,7 +68,7 @@
};
&lradc {
- vref-supply = <®_vcc3v0>;
+ vref-supply = <®_dcdc1>;
status = "okay";
button at 200 {
@@ -96,7 +96,7 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
@@ -106,7 +106,7 @@
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
status = "okay";
@@ -132,6 +132,79 @@
&r_rsb {
status = "okay";
+
+ axp22x: pmic at 3e3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3e3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_rtc_ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-rtc";
};
&uart0 {
--
2.6.2
next prev parent reply other threads:[~2015-11-24 3:48 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-24 3:48 [PATCH v4 0/6] mfd: axp20x: Add support for RSB based AXP223 Chen-Yu Tsai
2015-11-24 3:48 ` [PATCH v4 1/6] mfd: axp20x: Add AXP223 to list of supported PMICs in DT bindings Chen-Yu Tsai
2015-11-24 16:20 ` Lee Jones
2015-11-24 3:48 ` [PATCH v4 2/6] mfd: axp20x: Split the driver into core and i2c bits Chen-Yu Tsai
2015-11-24 9:37 ` Andy Shevchenko
2015-11-24 11:28 ` Chen-Yu Tsai
2015-11-24 12:35 ` Andy Shevchenko
2015-11-24 15:09 ` Chen-Yu Tsai
2015-11-24 15:21 ` Andy Shevchenko
2015-11-24 3:48 ` [PATCH v4 3/6] mfd: axp20x: Add support for RSB based AXP223 PMIC Chen-Yu Tsai
2015-11-24 9:38 ` Andy Shevchenko
2015-11-24 3:48 ` [PATCH v4 4/6] regulator: axp20x: Support new " Chen-Yu Tsai
2015-11-24 3:48 ` Chen-Yu Tsai [this message]
2015-11-24 3:48 ` [PATCH v4 6/6] ARM: dts: sun8i: q8-common: Add AXP223 PMIC device and regulator nodes Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1448336916-31212-6-git-send-email-wens@csie.org \
--to=wens@csie.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).