* [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes
@ 2016-01-26 16:30 Nicolas Ferre
2016-03-01 10:12 ` Nicolas Ferre
0 siblings, 1 reply; 3+ messages in thread
From: Nicolas Ferre @ 2016-01-26 16:30 UTC (permalink / raw)
To: linux-arm-kernel
The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 3f750f6170f2..82d0c19e9720 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -880,6 +880,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(35))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(36))>;
+ dma-names = "tx", "rx";
clocks = <&uart0_clk>;
clock-names = "usart";
status = "disabled";
@@ -889,6 +896,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(37))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(38))>;
+ dma-names = "tx", "rx";
clocks = <&uart1_clk>;
clock-names = "usart";
status = "disabled";
@@ -898,6 +912,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(39))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(40))>;
+ dma-names = "tx", "rx";
clocks = <&uart2_clk>;
clock-names = "usart";
status = "disabled";
@@ -1016,6 +1037,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xfc008000 0x100>;
interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(41))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(42))>;
+ dma-names = "tx", "rx";
clocks = <&uart3_clk>;
clock-names = "usart";
status = "disabled";
@@ -1024,6 +1052,13 @@
uart4: serial at fc00c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc00c000 0x100>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(43))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(44))>;
+ dma-names = "tx", "rx";
interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&uart4_clk>;
clock-names = "usart";
--
2.1.3
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes
2016-01-26 16:30 [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes Nicolas Ferre
@ 2016-03-01 10:12 ` Nicolas Ferre
0 siblings, 0 replies; 3+ messages in thread
From: Nicolas Ferre @ 2016-03-01 10:12 UTC (permalink / raw)
To: linux-arm-kernel
Le 26/01/2016 17:30, Nicolas Ferre a ?crit :
> The dmas/dma-names properties are added to the UART nodes. Note that additional
> properties are needed to enable them at the board level: check bindings for
> details.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Added to at91-4.6-dt.
Bye,
> ---
> arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
> index 3f750f6170f2..82d0c19e9720 100644
> --- a/arch/arm/boot/dts/sama5d2.dtsi
> +++ b/arch/arm/boot/dts/sama5d2.dtsi
> @@ -880,6 +880,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf801c000 0x100>;
> interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(35))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(36))>;
> + dma-names = "tx", "rx";
> clocks = <&uart0_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -889,6 +896,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf8020000 0x100>;
> interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(37))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(38))>;
> + dma-names = "tx", "rx";
> clocks = <&uart1_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -898,6 +912,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xf8024000 0x100>;
> interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(39))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(40))>;
> + dma-names = "tx", "rx";
> clocks = <&uart2_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -1016,6 +1037,13 @@
> compatible = "atmel,at91sam9260-usart";
> reg = <0xfc008000 0x100>;
> interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(41))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(42))>;
> + dma-names = "tx", "rx";
> clocks = <&uart3_clk>;
> clock-names = "usart";
> status = "disabled";
> @@ -1024,6 +1052,13 @@
> uart4: serial at fc00c000 {
> compatible = "atmel,at91sam9260-usart";
> reg = <0xfc00c000 0x100>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(43))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(44))>;
> + dma-names = "tx", "rx";
> interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
> clocks = <&uart4_clk>;
> clock-names = "usart";
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes
@ 2017-03-27 9:09 Alexandre Belloni
0 siblings, 0 replies; 3+ messages in thread
From: Alexandre Belloni @ 2017-03-27 9:09 UTC (permalink / raw)
To: linux-arm-kernel
From: Nicolas Ferre <nicolas.ferre@atmel.com>
commit b1708b72a0959a032cd2eebb77fa9086ea3e0c84 upstream
The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Cc: <stable@vger.kernel.org> # 4.4.x
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
Hi,
Commit 6b1d7b6f54c7deb80a00b9271dc3abb7a5674b65 triggered a bug in the atmel tty
driver when the dma channels are not specified. It is safe to backport
b1708b72a0959a032cd2eebb77fa9086ea3e0c84, defining the uart dma channels to fix
it.
arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 3f750f6170f2..82d0c19e9720 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -880,6 +880,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(35))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(36))>;
+ dma-names = "tx", "rx";
clocks = <&uart0_clk>;
clock-names = "usart";
status = "disabled";
@@ -889,6 +896,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(37))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(38))>;
+ dma-names = "tx", "rx";
clocks = <&uart1_clk>;
clock-names = "usart";
status = "disabled";
@@ -898,6 +912,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(39))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(40))>;
+ dma-names = "tx", "rx";
clocks = <&uart2_clk>;
clock-names = "usart";
status = "disabled";
@@ -1016,6 +1037,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xfc008000 0x100>;
interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(41))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(42))>;
+ dma-names = "tx", "rx";
clocks = <&uart3_clk>;
clock-names = "usart";
status = "disabled";
@@ -1024,6 +1052,13 @@
uart4: serial at fc00c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc00c000 0x100>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(43))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(44))>;
+ dma-names = "tx", "rx";
interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&uart4_clk>;
clock-names = "usart";
--
2.11.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2017-03-27 9:09 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-01-26 16:30 [PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes Nicolas Ferre
2016-03-01 10:12 ` Nicolas Ferre
-- strict thread matches above, loose matches on Subject: below --
2017-03-27 9:09 Alexandre Belloni
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).