[PATCH 0/3] ARM: mvebu: Add driver for the Zyxel NSA3XX hwmon MCU

[PATCH 0/3] ARM: mvebu: Add driver for the Zyxel NSA3XX hwmon MCU

[Adam Baker]

This patch series adds a driver to support the hardware monitoring MCU
that is present in some models of the Zyxel NSA3xx series of NAS units.

A patch is included to add it to the device tree for the NSA320 model,
patches to the other device trees will be included if testers come
forward (I already have a possible tester for NSA325).

There are no dependencies between the patches so I guess the first two
should go via the hardware monitoring maintainers and the third via
the ARM mvebu maintainers.

 [PATCH 1/3] Define a binding for the hardware monitoring chip present
 [PATCH 2/3] Create a driver to support the hardware monitoring chip
 [PATCH 3/3] Add an entry for the hardware monitoring MCU

 Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt |  21 ++++++++
 arch/arm/boot/dts/kirkwood-nsa320.dts                  |  13 ++++-
 drivers/hwmon/Kconfig                                  |  13 +++++
 drivers/hwmon/Makefile                                 |   1 +
 drivers/hwmon/nsa3xx-hwmon.c                           | 223 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 269 insertions(+), 2 deletions(-)

[PATCH 1/3] ARM: mvebu: Define binding for the nsa3xx-hwmon driver

[Adam Baker]

Define a binding for the hardware monitoring chip present in several
variants of the Zyxel NSA3xx NAS devices.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
---
 .../devicetree/bindings/hwmon/nsa320-mcu.txt        | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt

diff --git a/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt
new file mode 100644
index 0000000..7b346d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt
@@ -0,0 +1,21 @@
+Bindings for the fan / temperature monitor microcontroller used on
+the Zyxel NSA 320 and several subsequent models.
+
+Required properties:
+- compatible	: "zyxel,nsa320-mcu"
+- data-gpios	: The GPIO pin connected to the data line on the MCU
+- clk-gpios	: The GPIO pin connected to the clock line on the MCU
+- act-gpios	: The GPIO pin connected to the active line on the MCU
+
+Example:
+
+	hwmon {
+		compatible = "zyxel,nsa320-mcu";
+		pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act>;
+		pinctrl-names = "default";
+
+		data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+	};
+
-- 
2.1.4

[PATCH 1/3] ARM: mvebu: Define binding for the nsa3xx-hwmon driver

[Rob Herring]

On Wed, Feb 10, 2016 at 11:33:42PM +0000, Adam Baker wrote:
> Define a binding for the hardware monitoring chip present in several
> variants of the Zyxel NSA3xx NAS devices.
> 
> Signed-off-by: Adam Baker <linux@baker-net.org.uk>
> ---
>  .../devicetree/bindings/hwmon/nsa320-mcu.txt        | 21 +++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt

Acked-by: Rob Herring <robh@kernel.org>

[PATCH 2/3] ARM: mvebu: Create a NSA3xx hardware monitoring driver

[Adam Baker]

Create a driver to support the hardware monitoring chip present in
several models of Zyxel NSA3xx NAS devices.

The driver reads fan speed and temperature from a suitably programmed
MCU on the device.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
---
I've tested this on an NSA-320, I've had someone offer to test it on
NSA-325 so hopefully I will get a tested by back.
---
 drivers/hwmon/Kconfig        |  13 +++
 drivers/hwmon/Makefile       |   1 +
 drivers/hwmon/nsa3xx-hwmon.c | 223 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 237 insertions(+)
 create mode 100644 drivers/hwmon/nsa3xx-hwmon.c

diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 80a73bf..8801b78 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1757,6 +1757,19 @@ config SENSORS_ULTRA45
 	  This driver provides support for the Ultra45 workstation environmental
 	  sensors.
 
+config SENSORS_NSA3XX
+	tristate "ZyXEL NSA3xx fan speed and temperature sensors"
+	depends on GPIOLIB && OF
+	help
+	  If you say yes here you get support for hardware monitoring
+	  for the ZyXEL NSA3XX Media Servers.
+
+	  The sensor data is taken from a Holtek HT46R065 microcontroller
+	  connected to GPIO lines.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called nsa3xx-hwmon.
+
 if ACPI
 
 comment "ACPI drivers"
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 12a3239..e85414a 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -118,6 +118,7 @@ obj-$(CONFIG_SENSORS_MAX6650)	+= max6650.o
 obj-$(CONFIG_SENSORS_MAX6697)	+= max6697.o
 obj-$(CONFIG_SENSORS_MAX31790)	+= max31790.o
 obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o
+obj-$(CONFIG_SENSORS_NSA3XX)	+= nsa3xx-hwmon.o
 obj-$(CONFIG_SENSORS_MCP3021)	+= mcp3021.o
 obj-$(CONFIG_SENSORS_MENF21BMC_HWMON) += menf21bmc_hwmon.o
 obj-$(CONFIG_SENSORS_NCT6683)	+= nct6683.o
diff --git a/drivers/hwmon/nsa3xx-hwmon.c b/drivers/hwmon/nsa3xx-hwmon.c
new file mode 100644
index 0000000..0fbf118
--- /dev/null
+++ b/drivers/hwmon/nsa3xx-hwmon.c
@@ -0,0 +1,223 @@
+/*
+ * drivers/hwmon/nsa3xx-hwmon.c
+ *
+ * ZyXEL NSA3xx Media Servers
+ * hardware monitoring
+ *
+ * Copyright (C) 2016 Adam Baker <linux@baker-net.org.uk>
+ * based on a board file driver
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License v2 as published by the
+ * Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/jiffies.h>
+#include <linux/delay.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+
+#define MAGIC_NUMBER 0x55
+
+/*
+ * The Zyxel hwmon MCU is a Holtek HT46R065 that is factory programmed
+ * to perform temperature and fan speed monitoring. It is read by taking
+ * the active pin low. The 32 bit output word is then clocked onto the
+ * data line. The MSB of the data word is a magic nuber to indicate it
+ * has been read correctly, the next byte is the fan speed (in hundreds
+ * of RPM) and the last two bytes are the temperature (in tenths of a
+ * degree)
+ */
+
+struct nsa3xx_hwmon {
+	struct device		*classdev;
+	struct mutex		update_lock;	/* lock GPIO operations */
+	unsigned long		last_updated;	/* jiffies */
+	u32			mcu_data;
+	struct gpio_desc	*act;
+	struct gpio_desc	*clk;
+	struct gpio_desc	*data;
+};
+
+enum nsa3xx_inputs {
+	NSA3XX_FAN = 1,
+	NSA3XX_TEMP = 0,
+};
+
+static const char * const nsa3xx_input_names[] = {
+	[NSA3XX_FAN] = "Chassis Fan",
+	[NSA3XX_TEMP] = "System Temperature",
+};
+
+/* Although this protocol looks similar to SPI the long delay
+ * between the active (aka chip select) signal and the shorter
+ * delay between clock pulses are needed for reliable operation.
+ * The delays provided are taken from the manufacturer kernel,
+ * testing suggest they probably incorporate a reasonable safety
+ * margin. (The single device tested became unreliable if the
+ * delay was reduced to 1/10th of this value.)
+ */
+static unsigned long nsa3xx_hwmon_update(struct device *dev)
+{
+	u32 mcu_data;
+	u32 mask;
+	struct nsa3xx_hwmon *hwmon = dev_get_drvdata(dev);
+
+	mutex_lock(&hwmon->update_lock);
+
+	mcu_data = hwmon->mcu_data;
+
+	if (time_after(jiffies, hwmon->last_updated + HZ) ||
+							mcu_data == 0) {
+
+		gpiod_set_value(hwmon->act, 1);
+		msleep(100);
+
+		for (mask = BIT(31); mask; mask >>= 1) {
+			gpiod_set_value(hwmon->clk, 0);
+			usleep_range(100, 200);
+			gpiod_set_value(hwmon->clk, 1);
+			usleep_range(100, 200);
+			if (gpiod_get_value(hwmon->data))
+				mcu_data |= mask;
+		}
+
+		gpiod_set_value(hwmon->act, 0);
+		dev_dbg(dev, "Read raw MCU data %08x\n", mcu_data);
+
+		if ((mcu_data >> 24) != MAGIC_NUMBER) {
+			dev_err(dev, "Read invalid MCU data %08x\n", mcu_data);
+			mcu_data = 0;
+		}
+
+		hwmon->mcu_data = mcu_data;
+		hwmon->last_updated = jiffies;
+	}
+
+	mutex_unlock(&hwmon->update_lock);
+
+	return mcu_data;
+}
+
+static ssize_t show_label(struct device *dev,
+			  struct device_attribute *attr, char *buf)
+{
+	int channel = to_sensor_dev_attr(attr)->index;
+
+	return sprintf(buf, "%s\n", nsa3xx_input_names[channel]);
+}
+
+static ssize_t show_value(struct device *dev,
+			  struct device_attribute *attr, char *buf)
+{
+	int channel = to_sensor_dev_attr(attr)->index;
+	unsigned long mcu_data = nsa3xx_hwmon_update(dev);
+	unsigned long value = 0;
+
+	pr_debug("channel value 0x%02x!\n", channel);
+	switch (channel) {
+	case NSA3XX_TEMP:
+		value = (mcu_data & 0xffff) * 100;
+		break;
+	case NSA3XX_FAN:
+		value = ((mcu_data & 0xff0000) >> 16) * 100;
+		break;
+	}
+	return sprintf(buf, "%lu\n", value);
+}
+
+static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, show_label, NULL, NSA3XX_TEMP);
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_value, NULL, NSA3XX_TEMP);
+static SENSOR_DEVICE_ATTR(fan1_label, S_IRUGO, show_label, NULL, NSA3XX_FAN);
+static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_value, NULL, NSA3XX_FAN);
+
+static struct attribute *nsa3xx_attrs[] = {
+	&sensor_dev_attr_temp1_label.dev_attr.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_fan1_label.dev_attr.attr,
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	NULL
+};
+
+ATTRIBUTE_GROUPS(nsa3xx);
+
+static const struct of_device_id of_nsa3xx_hwmon_match[] = {
+	{ .compatible = "zyxel,nsa320-mcu", },
+	{ },
+};
+
+static int nsa3xx_hwmon_probe(struct platform_device *pdev)
+{
+	struct nsa3xx_hwmon *hwmon;
+
+	hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL);
+	if (!hwmon)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, hwmon);
+
+	/* Look up the GPIO pins to use */
+	hwmon->act = devm_gpiod_get(&pdev->dev, "act", GPIOD_OUT_LOW);
+	hwmon->clk = devm_gpiod_get(&pdev->dev, "clk", GPIOD_OUT_HIGH);
+	hwmon->data = devm_gpiod_get(&pdev->dev, "data", GPIOD_IN);
+
+	if (IS_ERR(hwmon->act))
+		return PTR_ERR(hwmon->act);
+	if (IS_ERR(hwmon->clk))
+		return PTR_ERR(hwmon->clk);
+	if (IS_ERR(hwmon->data))
+		return PTR_ERR(hwmon->data);
+
+	mutex_init(&hwmon->update_lock);
+
+	hwmon->classdev = devm_hwmon_device_register_with_groups(&pdev->dev,
+					"nsa3xx", hwmon, nsa3xx_groups);
+	if (IS_ERR(hwmon->classdev))
+		return PTR_ERR(hwmon->classdev);
+
+	dev_dbg(&pdev->dev, "initialized\n");
+
+	return 0;
+}
+
+static int nsa3xx_hwmon_remove(struct platform_device *pdev)
+{
+	/* All resources are allocated with devm_*() so
+	 * there is nothing to do here.
+	 */
+
+	return 0;
+}
+
+static struct platform_driver nsa3xx_hwmon_driver = {
+	.probe = nsa3xx_hwmon_probe,
+	.remove = nsa3xx_hwmon_remove,
+	.driver = {
+		.name = "nsa3xx-hwmon",
+		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(of_nsa3xx_hwmon_match),
+	},
+};
+
+module_platform_driver(nsa3xx_hwmon_driver);
+
+MODULE_DEVICE_TABLE(of, of_nsa3xx_hwmon_match);
+MODULE_AUTHOR("Peter Schildmann <linux@schildmann.info>");
+MODULE_AUTHOR("Adam Baker <linux@baker-net.org.uk>");
+MODULE_DESCRIPTION("NSA3XX Hardware Monitoring");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:nsa3xx-hwmon");
-- 
2.1.4

[PATCH 2/3] ARM: mvebu: Create a NSA3xx hardware monitoring driver

[Guenter Roeck]

Hi,

On Wed, Feb 10, 2016 at 11:33:43PM +0000, Adam Baker wrote:
> Create a driver to support the hardware monitoring chip present in
> several models of Zyxel NSA3xx NAS devices.
> 
> The driver reads fan speed and temperature from a suitably programmed
> MCU on the device.
> 
> Signed-off-by: Adam Baker <linux@baker-net.org.uk>

Please name the driver nsa320. It may ultimately support other devices,
but that doesn't mean it is going to support NSA-35x or other future
similar devices.

Got the headline, please use

hwmon: Add driver for Zyxel NSA-320

> ---
> I've tested this on an NSA-320, I've had someone offer to test it on
> NSA-325 so hopefully I will get a tested by back.
> ---
>  drivers/hwmon/Kconfig        |  13 +++
>  drivers/hwmon/Makefile       |   1 +
>  drivers/hwmon/nsa3xx-hwmon.c | 223 +++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 237 insertions(+)
>  create mode 100644 drivers/hwmon/nsa3xx-hwmon.c
> 
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 80a73bf..8801b78 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -1757,6 +1757,19 @@ config SENSORS_ULTRA45
>  	  This driver provides support for the Ultra45 workstation environmental
>  	  sensors.
>  
> +config SENSORS_NSA3XX

Please try to stick with alphabetic order.

> +	tristate "ZyXEL NSA3xx fan speed and temperature sensors"

... NSA-320 and compatible ...

> +	depends on GPIOLIB && OF

Can you add some additional dependencies ?

It is quite unlikely that the driver is needed on an X86.
Please use at least

	depends on ARM || COMPILE_TEST

or a more specific dependency if the SoC is known. MACH_KIRKWOOD, maybe ?

> +	help
> +	  If you say yes here you get support for hardware monitoring
> +	  for the ZyXEL NSA3XX Media Servers.

Please be specific which devices are supported. Feel free to add "and
compatibles", but please no generic and misleading statements such as 3XX.

> +
> +	  The sensor data is taken from a Holtek HT46R065 microcontroller
> +	  connected to GPIO lines.
> +
Is that relevant ?

> +	  This driver can also be built as a module. If so, the module
> +	  will be called nsa3xx-hwmon.
> +
>  if ACPI
>  
>  comment "ACPI drivers"
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index 12a3239..e85414a 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -118,6 +118,7 @@ obj-$(CONFIG_SENSORS_MAX6650)	+= max6650.o
>  obj-$(CONFIG_SENSORS_MAX6697)	+= max6697.o
>  obj-$(CONFIG_SENSORS_MAX31790)	+= max31790.o
>  obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o
> +obj-$(CONFIG_SENSORS_NSA3XX)	+= nsa3xx-hwmon.o

Please try to stick with alphabetic order.

>  obj-$(CONFIG_SENSORS_MCP3021)	+= mcp3021.o
>  obj-$(CONFIG_SENSORS_MENF21BMC_HWMON) += menf21bmc_hwmon.o
>  obj-$(CONFIG_SENSORS_NCT6683)	+= nct6683.o
> diff --git a/drivers/hwmon/nsa3xx-hwmon.c b/drivers/hwmon/nsa3xx-hwmon.c
> new file mode 100644
> index 0000000..0fbf118
> --- /dev/null
> +++ b/drivers/hwmon/nsa3xx-hwmon.c

nsa320-hwmon.c

> @@ -0,0 +1,223 @@
> +/*
> + * drivers/hwmon/nsa3xx-hwmon.c
> + *
> + * ZyXEL NSA3xx Media Servers

Please be specific.

> + * hardware monitoring
> + *
> + * Copyright (C) 2016 Adam Baker <linux@baker-net.org.uk>
> + * based on a board file driver
> + * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License v2 as published by the
> + * Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
> + * more details.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +#include <linux/err.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>
> +#include <linux/jiffies.h>
> +#include <linux/delay.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_platform.h>
> +
Please order include files alphabetically.

> +#define MAGIC_NUMBER 0x55
> +
> +/*
> + * The Zyxel hwmon MCU is a Holtek HT46R065 that is factory programmed
> + * to perform temperature and fan speed monitoring. It is read by taking
> + * the active pin low. The 32 bit output word is then clocked onto the
> + * data line. The MSB of the data word is a magic nuber to indicate it
> + * has been read correctly, the next byte is the fan speed (in hundreds
> + * of RPM) and the last two bytes are the temperature (in tenths of a
> + * degree)
> + */
> +
> +struct nsa3xx_hwmon {

s/nsa3xx/nsa320/g for the entire file, please.

> +	struct device		*classdev;
> +	struct mutex		update_lock;	/* lock GPIO operations */
> +	unsigned long		last_updated;	/* jiffies */
> +	u32			mcu_data;

I would suggest to use unsigned long here. See below for reasons.

> +	struct gpio_desc	*act;
> +	struct gpio_desc	*clk;
> +	struct gpio_desc	*data;
> +};
> +
> +enum nsa3xx_inputs {
> +	NSA3XX_FAN = 1,
> +	NSA3XX_TEMP = 0,

Any special reason for the unusual order ? If yes, please explain.

> +};
> +
> +static const char * const nsa3xx_input_names[] = {
> +	[NSA3XX_FAN] = "Chassis Fan",
> +	[NSA3XX_TEMP] = "System Temperature",
> +};
> +
> +/* Although this protocol looks similar to SPI the long delay
> + * between the active (aka chip select) signal and the shorter
> + * delay between clock pulses are needed for reliable operation.
> + * The delays provided are taken from the manufacturer kernel,
> + * testing suggest they probably incorporate a reasonable safety
> + * margin. (The single device tested became unreliable if the
> + * delay was reduced to 1/10th of this value.)
> + */
> +static unsigned long nsa3xx_hwmon_update(struct device *dev)
> +{
> +	u32 mcu_data;
> +	u32 mask;
> +	struct nsa3xx_hwmon *hwmon = dev_get_drvdata(dev);
> +
> +	mutex_lock(&hwmon->update_lock);
> +
> +	mcu_data = hwmon->mcu_data;
> +
> +	if (time_after(jiffies, hwmon->last_updated + HZ) ||
> +							mcu_data == 0) {
> +

Please no blank line here. Also, please align continuation lines with '('.
However, unless I am missing something, the continuation line is not needed
in the first place. Please no unnecessary continuation lines.

> +		gpiod_set_value(hwmon->act, 1);
> +		msleep(100);
> +
> +		for (mask = BIT(31); mask; mask >>= 1) {

Since you are using BIT(), please include linux/bitops.h.

> +			gpiod_set_value(hwmon->clk, 0);
> +			usleep_range(100, 200);
> +			gpiod_set_value(hwmon->clk, 1);
> +			usleep_range(100, 200);
> +			if (gpiod_get_value(hwmon->data))
> +				mcu_data |= mask;
> +		}
> +
> +		gpiod_set_value(hwmon->act, 0);
> +		dev_dbg(dev, "Read raw MCU data %08x\n", mcu_data);
> +
> +		if ((mcu_data >> 24) != MAGIC_NUMBER) {
> +			dev_err(dev, "Read invalid MCU data %08x\n", mcu_data);
> +			mcu_data = 0;

Instead of an error message, it would be better to return an error code
(probably -EIO since we don't know better).

The calling code can then return the error to user space.

> +		}
> +
> +		hwmon->mcu_data = mcu_data;
> +		hwmon->last_updated = jiffies;
> +	}
> +
> +	mutex_unlock(&hwmon->update_lock);
> +
> +	return mcu_data;
> +}
> +
> +static ssize_t show_label(struct device *dev,
> +			  struct device_attribute *attr, char *buf)
> +{
> +	int channel = to_sensor_dev_attr(attr)->index;
> +
> +	return sprintf(buf, "%s\n", nsa3xx_input_names[channel]);
> +}
> +
> +static ssize_t show_value(struct device *dev,
> +			  struct device_attribute *attr, char *buf)
> +{
> +	int channel = to_sensor_dev_attr(attr)->index;
> +	unsigned long mcu_data = nsa3xx_hwmon_update(dev);
> +	unsigned long value = 0;
> +

If nsa3xx_hwmon_update() returns an error code, you can use

	if (IS_ERR_VALUE(mcu_data))
		return (long)mcu_data;

or even better have nsa3xx_hwmon_update() return int directly
to indicate an error.

> +	pr_debug("channel value 0x%02x!\n", channel);

Is this really useful ? I would suggest to drop debug messages
unless really needed. If you really think the message is useful,
please use dev_dbg().

> +	switch (channel) {
> +	case NSA3XX_TEMP:
> +		value = (mcu_data & 0xffff) * 100;
> +		break;
> +	case NSA3XX_FAN:
> +		value = ((mcu_data & 0xff0000) >> 16) * 100;
> +		break;
> +	}
> +	return sprintf(buf, "%lu\n", value);
> +}
> +
> +static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, show_label, NULL, NSA3XX_TEMP);
> +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_value, NULL, NSA3XX_TEMP);
> +static SENSOR_DEVICE_ATTR(fan1_label, S_IRUGO, show_label, NULL, NSA3XX_FAN);
> +static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_value, NULL, NSA3XX_FAN);
> +
> +static struct attribute *nsa3xx_attrs[] = {
> +	&sensor_dev_attr_temp1_label.dev_attr.attr,
> +	&sensor_dev_attr_temp1_input.dev_attr.attr,
> +	&sensor_dev_attr_fan1_label.dev_attr.attr,
> +	&sensor_dev_attr_fan1_input.dev_attr.attr,
> +	NULL
> +};
> +
> +ATTRIBUTE_GROUPS(nsa3xx);
> +
> +static const struct of_device_id of_nsa3xx_hwmon_match[] = {
> +	{ .compatible = "zyxel,nsa320-mcu", },
> +	{ },
> +};
> +
> +static int nsa3xx_hwmon_probe(struct platform_device *pdev)
> +{
> +	struct nsa3xx_hwmon *hwmon;
> +
> +	hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL);
> +	if (!hwmon)
> +		return -ENOMEM;
> +
> +	platform_set_drvdata(pdev, hwmon);

Unnecessary.

> +
> +	/* Look up the GPIO pins to use */
> +	hwmon->act = devm_gpiod_get(&pdev->dev, "act", GPIOD_OUT_LOW);
> +	hwmon->clk = devm_gpiod_get(&pdev->dev, "clk", GPIOD_OUT_HIGH);
> +	hwmon->data = devm_gpiod_get(&pdev->dev, "data", GPIOD_IN);
> +
> +	if (IS_ERR(hwmon->act))
> +		return PTR_ERR(hwmon->act);
> +	if (IS_ERR(hwmon->clk))
> +		return PTR_ERR(hwmon->clk);
> +	if (IS_ERR(hwmon->data))
> +		return PTR_ERR(hwmon->data);

Please reorder to have the error checks immediately after the calls
to devm_gpiod_get().

> +
> +	mutex_init(&hwmon->update_lock);
> +
> +	hwmon->classdev = devm_hwmon_device_register_with_groups(&pdev->dev,
> +					"nsa3xx", hwmon, nsa3xx_groups);

classdev is only used in this function and thus does not have to be kept
in struct nsa3xx_hwmon.

> +	if (IS_ERR(hwmon->classdev))
> +		return PTR_ERR(hwmon->classdev);
> +
> +	dev_dbg(&pdev->dev, "initialized\n");
> +

This message is really unnecessary. Please just use
	return PTR_ERR_OR_ZERO(classdev);

> +	return 0;
> +}
> +
> +static int nsa3xx_hwmon_remove(struct platform_device *pdev)
> +{
> +	/* All resources are allocated with devm_*() so
> +	 * there is nothing to do here.
> +	 */
> +
> +	return 0;
> +}

If the remove function is not needed, it is not needed and should not
exist in the first place. Please no dummy functions.

> +
> +static struct platform_driver nsa3xx_hwmon_driver = {
> +	.probe = nsa3xx_hwmon_probe,
> +	.remove = nsa3xx_hwmon_remove,
> +	.driver = {
> +		.name = "nsa3xx-hwmon",
> +		.owner = THIS_MODULE,
> +		.of_match_table = of_match_ptr(of_nsa3xx_hwmon_match),
> +	},
> +};
> +
> +module_platform_driver(nsa3xx_hwmon_driver);
> +
> +MODULE_DEVICE_TABLE(of, of_nsa3xx_hwmon_match);
> +MODULE_AUTHOR("Peter Schildmann <linux@schildmann.info>");
> +MODULE_AUTHOR("Adam Baker <linux@baker-net.org.uk>");
> +MODULE_DESCRIPTION("NSA3XX Hardware Monitoring");
> +MODULE_LICENSE("GPL");

GPL v2

> +MODULE_ALIAS("platform:nsa3xx-hwmon");
> -- 
> 2.1.4
> 

[PATCH 2/3] ARM: mvebu: Create a NSA3xx hardware monitoring driver

[Adam Baker]

On 13/02/16 02:35, Guenter Roeck wrote:
> Hi,
>
> On Wed, Feb 10, 2016 at 11:33:43PM +0000, Adam Baker wrote:
>> Create a driver to support the hardware monitoring chip present in
>> several models of Zyxel NSA3xx NAS devices.
>>
>> The driver reads fan speed and temperature from a suitably programmed
>> MCU on the device.
>>
>> Signed-off-by: Adam Baker <linux@baker-net.org.uk>
>
> Please name the driver nsa320. It may ultimately support other devices,
> but that doesn't mean it is going to support NSA-35x or other future
> similar devices.
>
> Got the headline, please use
>
> hwmon: Add driver for Zyxel NSA-320
>
OK

>> ---
>> I've tested this on an NSA-320, I've had someone offer to test it on
>> NSA-325 so hopefully I will get a tested by back.
>> ---
>>   drivers/hwmon/Kconfig        |  13 +++
>>   drivers/hwmon/Makefile       |   1 +
>>   drivers/hwmon/nsa3xx-hwmon.c | 223 +++++++++++++++++++++++++++++++++++++++++++
>>   3 files changed, 237 insertions(+)
>>   create mode 100644 drivers/hwmon/nsa3xx-hwmon.c
>>
>> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
>> index 80a73bf..8801b78 100644
>> --- a/drivers/hwmon/Kconfig
>> +++ b/drivers/hwmon/Kconfig
>> @@ -1757,6 +1757,19 @@ config SENSORS_ULTRA45
>>   	  This driver provides support for the Ultra45 workstation environmental
>>   	  sensors.
>>
>> +config SENSORS_NSA3XX
>
> Please try to stick with alphabetic order.
done
>
>> +	tristate "ZyXEL NSA3xx fan speed and temperature sensors"
>
> ... NSA-320 and compatible ...
done
>
>> +	depends on GPIOLIB && OF
>
> Can you add some additional dependencies ?
>
> It is quite unlikely that the driver is needed on an X86.
> Please use at least
>
> 	depends on ARM || COMPILE_TEST
>
> or a more specific dependency if the SoC is known. MACH_KIRKWOOD, maybe ?
done - depends on MACH_KIRKWOOD || COMPILE_TEST
>
>> +	help
>> +	  If you say yes here you get support for hardware monitoring
>> +	  for the ZyXEL NSA3XX Media Servers.
>
> Please be specific which devices are supported. Feel free to add "and
> compatibles", but please no generic and misleading statements such as 3XX.
>
Changed to NSA320 and compatible and noted NSA325 and some NSA310 
variants are probably compatible
>> +
>> +	  The sensor data is taken from a Holtek HT46R065 microcontroller
>> +	  connected to GPIO lines.
>> +
> Is that relevant ?
>
I'm guessing that it is if someone is trying to work out if the unit 
they've got is likely to be compatible.

>> +	  This driver can also be built as a module. If so, the module
>> +	  will be called nsa3xx-hwmon.
>> +
>>   if ACPI
>>
>>   comment "ACPI drivers"
>> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
>> index 12a3239..e85414a 100644
>> --- a/drivers/hwmon/Makefile
>> +++ b/drivers/hwmon/Makefile
>> @@ -118,6 +118,7 @@ obj-$(CONFIG_SENSORS_MAX6650)	+= max6650.o
>>   obj-$(CONFIG_SENSORS_MAX6697)	+= max6697.o
>>   obj-$(CONFIG_SENSORS_MAX31790)	+= max31790.o
>>   obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o
>> +obj-$(CONFIG_SENSORS_NSA3XX)	+= nsa3xx-hwmon.o
>
> Please try to stick with alphabetic order.
done
>
>>   obj-$(CONFIG_SENSORS_MCP3021)	+= mcp3021.o
>>   obj-$(CONFIG_SENSORS_MENF21BMC_HWMON) += menf21bmc_hwmon.o
>>   obj-$(CONFIG_SENSORS_NCT6683)	+= nct6683.o
>> diff --git a/drivers/hwmon/nsa3xx-hwmon.c b/drivers/hwmon/nsa3xx-hwmon.c
>> new file mode 100644
>> index 0000000..0fbf118
>> --- /dev/null
>> +++ b/drivers/hwmon/nsa3xx-hwmon.c
>
> nsa320-hwmon.c
done
>
>> @@ -0,0 +1,223 @@
>> +/*
>> + * drivers/hwmon/nsa3xx-hwmon.c
>> + *
>> + * ZyXEL NSA3xx Media Servers
>
> Please be specific.
done
>
>> + * hardware monitoring
>> + *
>> + * Copyright (C) 2016 Adam Baker <linux@baker-net.org.uk>
>> + * based on a board file driver
>> + * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
>> + *
>> + * This program is free software; you can redistribute it and/or modify it
>> + * under the terms of the GNU General Public License v2 as published by the
>> + * Free Software Foundation.
>> + *
>> + * This program is distributed in the hope that it will be useful, but WITHOUT
>> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
>> + * more details.
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/mutex.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/err.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/hwmon.h>
>> +#include <linux/hwmon-sysfs.h>
>> +#include <linux/jiffies.h>
>> +#include <linux/delay.h>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of_platform.h>
>> +
> Please order include files alphabetically.
done
>
>> +#define MAGIC_NUMBER 0x55
>> +
>> +/*
>> + * The Zyxel hwmon MCU is a Holtek HT46R065 that is factory programmed
>> + * to perform temperature and fan speed monitoring. It is read by taking
>> + * the active pin low. The 32 bit output word is then clocked onto the
>> + * data line. The MSB of the data word is a magic nuber to indicate it
>> + * has been read correctly, the next byte is the fan speed (in hundreds
>> + * of RPM) and the last two bytes are the temperature (in tenths of a
>> + * degree)
>> + */
>> +
>> +struct nsa3xx_hwmon {
>
> s/nsa3xx/nsa320/g for the entire file, please.
done
>
>> +	struct device		*classdev;
>> +	struct mutex		update_lock;	/* lock GPIO operations */
>> +	unsigned long		last_updated;	/* jiffies */
>> +	u32			mcu_data;
>
> I would suggest to use unsigned long here. See below for reasons.
>
I've changed the return value to int
>> +	struct gpio_desc	*act;
>> +	struct gpio_desc	*clk;
>> +	struct gpio_desc	*data;
>> +};
>> +
>> +enum nsa3xx_inputs {
>> +	NSA3XX_FAN = 1,
>> +	NSA3XX_TEMP = 0,
>
> Any special reason for the unusual order ? If yes, please explain.
No, changed
>
>> +};
>> +
>> +static const char * const nsa3xx_input_names[] = {
>> +	[NSA3XX_FAN] = "Chassis Fan",
>> +	[NSA3XX_TEMP] = "System Temperature",
>> +};
>> +
>> +/* Although this protocol looks similar to SPI the long delay
>> + * between the active (aka chip select) signal and the shorter
>> + * delay between clock pulses are needed for reliable operation.
>> + * The delays provided are taken from the manufacturer kernel,
>> + * testing suggest they probably incorporate a reasonable safety
>> + * margin. (The single device tested became unreliable if the
>> + * delay was reduced to 1/10th of this value.)
>> + */
>> +static unsigned long nsa3xx_hwmon_update(struct device *dev)
>> +{
>> +	u32 mcu_data;
>> +	u32 mask;
>> +	struct nsa3xx_hwmon *hwmon = dev_get_drvdata(dev);
>> +
>> +	mutex_lock(&hwmon->update_lock);
>> +
>> +	mcu_data = hwmon->mcu_data;
>> +
>> +	if (time_after(jiffies, hwmon->last_updated + HZ) ||
>> +							mcu_data == 0) {
>> +
>
> Please no blank line here. Also, please align continuation lines with '('.
> However, unless I am missing something, the continuation line is not needed
> in the first place. Please no unnecessary continuation lines.
done
>
>> +		gpiod_set_value(hwmon->act, 1);
>> +		msleep(100);
>> +
>> +		for (mask = BIT(31); mask; mask >>= 1) {
>
> Since you are using BIT(), please include linux/bitops.h.
>
done
>> +			gpiod_set_value(hwmon->clk, 0);
>> +			usleep_range(100, 200);
>> +			gpiod_set_value(hwmon->clk, 1);
>> +			usleep_range(100, 200);
>> +			if (gpiod_get_value(hwmon->data))
>> +				mcu_data |= mask;
>> +		}
>> +
>> +		gpiod_set_value(hwmon->act, 0);
>> +		dev_dbg(dev, "Read raw MCU data %08x\n", mcu_data);
>> +
>> +		if ((mcu_data >> 24) != MAGIC_NUMBER) {
>> +			dev_err(dev, "Read invalid MCU data %08x\n", mcu_data);
>> +			mcu_data = 0;
>
> Instead of an error message, it would be better to return an error code
> (probably -EIO since we don't know better).
>
> The calling code can then return the error to user space.
nsa320_hwmon_update() now returns an int, either 0 or -EIO and the 
caller can read the data from the nsa320_hwmon structure if it returns 
0. dev_err changed to dev_dbg as the raw data is helpful for debugging.
>
>> +		}
>> +
>> +		hwmon->mcu_data = mcu_data;
>> +		hwmon->last_updated = jiffies;
>> +	}
>> +
>> +	mutex_unlock(&hwmon->update_lock);
>> +
>> +	return mcu_data;
>> +}
>> +
>> +static ssize_t show_label(struct device *dev,
>> +			  struct device_attribute *attr, char *buf)
>> +{
>> +	int channel = to_sensor_dev_attr(attr)->index;
>> +
>> +	return sprintf(buf, "%s\n", nsa3xx_input_names[channel]);
>> +}
>> +
>> +static ssize_t show_value(struct device *dev,
>> +			  struct device_attribute *attr, char *buf)
>> +{
>> +	int channel = to_sensor_dev_attr(attr)->index;
>> +	unsigned long mcu_data = nsa3xx_hwmon_update(dev);
>> +	unsigned long value = 0;
>> +
>
> If nsa3xx_hwmon_update() returns an error code, you can use
>
> 	if (IS_ERR_VALUE(mcu_data))
> 		return (long)mcu_data;
>
> or even better have nsa3xx_hwmon_update() return int directly
> to indicate an error.
nsa320_hwmon_update() now returns an int error code or zero and the 
caller gets the data fro the struct if it succeeds
>
>> +	pr_debug("channel value 0x%02x!\n", channel);
>
> Is this really useful ? I would suggest to drop debug messages
> unless really needed. If you really think the message is useful,
> please use dev_dbg().
deleted
>
>> +	switch (channel) {
>> +	case NSA3XX_TEMP:
>> +		value = (mcu_data & 0xffff) * 100;
>> +		break;
>> +	case NSA3XX_FAN:
>> +		value = ((mcu_data & 0xff0000) >> 16) * 100;
>> +		break;
>> +	}
>> +	return sprintf(buf, "%lu\n", value);
>> +}
>> +
>> +static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, show_label, NULL, NSA3XX_TEMP);
>> +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_value, NULL, NSA3XX_TEMP);
>> +static SENSOR_DEVICE_ATTR(fan1_label, S_IRUGO, show_label, NULL, NSA3XX_FAN);
>> +static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_value, NULL, NSA3XX_FAN);
>> +
>> +static struct attribute *nsa3xx_attrs[] = {
>> +	&sensor_dev_attr_temp1_label.dev_attr.attr,
>> +	&sensor_dev_attr_temp1_input.dev_attr.attr,
>> +	&sensor_dev_attr_fan1_label.dev_attr.attr,
>> +	&sensor_dev_attr_fan1_input.dev_attr.attr,
>> +	NULL
>> +};
>> +
>> +ATTRIBUTE_GROUPS(nsa3xx);
>> +
>> +static const struct of_device_id of_nsa3xx_hwmon_match[] = {
>> +	{ .compatible = "zyxel,nsa320-mcu", },
>> +	{ },
>> +};
>> +
>> +static int nsa3xx_hwmon_probe(struct platform_device *pdev)
>> +{
>> +	struct nsa3xx_hwmon *hwmon;
>> +
>> +	hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL);
>> +	if (!hwmon)
>> +		return -ENOMEM;
>> +
>> +	platform_set_drvdata(pdev, hwmon);
>
> Unnecessary.
removed
>
>> +
>> +	/* Look up the GPIO pins to use */
>> +	hwmon->act = devm_gpiod_get(&pdev->dev, "act", GPIOD_OUT_LOW);
>> +	hwmon->clk = devm_gpiod_get(&pdev->dev, "clk", GPIOD_OUT_HIGH);
>> +	hwmon->data = devm_gpiod_get(&pdev->dev, "data", GPIOD_IN);
>> +
>> +	if (IS_ERR(hwmon->act))
>> +		return PTR_ERR(hwmon->act);
>> +	if (IS_ERR(hwmon->clk))
>> +		return PTR_ERR(hwmon->clk);
>> +	if (IS_ERR(hwmon->data))
>> +		return PTR_ERR(hwmon->data);
>
> Please reorder to have the error checks immediately after the calls
> to devm_gpiod_get().
done
>
>> +
>> +	mutex_init(&hwmon->update_lock);
>> +
>> +	hwmon->classdev = devm_hwmon_device_register_with_groups(&pdev->dev,
>> +					"nsa3xx", hwmon, nsa3xx_groups);
>
> classdev is only used in this function and thus does not have to be kept
> in struct nsa3xx_hwmon.
removed
>
>> +	if (IS_ERR(hwmon->classdev))
>> +		return PTR_ERR(hwmon->classdev);
>> +
>> +	dev_dbg(&pdev->dev, "initialized\n");
>> +
>
> This message is really unnecessary. Please just use
> 	return PTR_ERR_OR_ZERO(classdev);
done
>
>> +	return 0;
>> +}
>> +
>> +static int nsa3xx_hwmon_remove(struct platform_device *pdev)
>> +{
>> +	/* All resources are allocated with devm_*() so
>> +	 * there is nothing to do here.
>> +	 */
>> +
>> +	return 0;
>> +}
>
> If the remove function is not needed, it is not needed and should not
> exist in the first place. Please no dummy functions.
>
done, I've left a comment to explain why there is no remove to prompt 
anyone who changes the code to use devres or add a remove method
>> +
>> +static struct platform_driver nsa3xx_hwmon_driver = {
>> +	.probe = nsa3xx_hwmon_probe,
>> +	.remove = nsa3xx_hwmon_remove,
>> +	.driver = {
>> +		.name = "nsa3xx-hwmon",
>> +		.owner = THIS_MODULE,
>> +		.of_match_table = of_match_ptr(of_nsa3xx_hwmon_match),
>> +	},
>> +};
>> +
>> +module_platform_driver(nsa3xx_hwmon_driver);
>> +
>> +MODULE_DEVICE_TABLE(of, of_nsa3xx_hwmon_match);
>> +MODULE_AUTHOR("Peter Schildmann <linux@schildmann.info>");
>> +MODULE_AUTHOR("Adam Baker <linux@baker-net.org.uk>");
>> +MODULE_DESCRIPTION("NSA3XX Hardware Monitoring");
>> +MODULE_LICENSE("GPL");
>
> GPL v2
done
>
>> +MODULE_ALIAS("platform:nsa3xx-hwmon");
>> --
>> 2.1.4
>>

[PATCH 3/3] ARM: mvebu: Add the hardware monitor to the NSA320 device tree

[Adam Baker]

Add an entry for the hardware monitoring MCU

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
---
 arch/arm/boot/dts/kirkwood-nsa320.dts | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/kirkwood-nsa320.dts b/arch/arm/boot/dts/kirkwood-nsa320.dts
index 24f686d..2a935e9 100644
--- a/arch/arm/boot/dts/kirkwood-nsa320.dts
+++ b/arch/arm/boot/dts/kirkwood-nsa320.dts
@@ -193,10 +193,19 @@
 		};
 	};
 
+	hwmon {
+		compatible = "zyxel,nsa320-mcu";
+		pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act>;
+		pinctrl-names = "default";
+
+		data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+	};
+
 	/* The following pins are currently not assigned to a driver,
 	   some of them should be configured as inputs.
-	pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act
-		     &pmx_htp &pmx_vid_b1
+	pinctrl-0 = <&pmx_htp &pmx_vid_b1
 		     &pmx_power_resume_data &pmx_power_resume_clk>; */
 };
 
-- 
2.1.4

[PATCH 0/3] ARM: mvebu: Add driver for the Zyxel NSA3XX hwmon MCU

[Gregory CLEMENT]

Hi Adam,
 
 On jeu., f?vr. 11 2016, Adam Baker <linux@baker-net.org.uk> wrote:

> This patch series adds a driver to support the hardware monitoring MCU
> that is present in some models of the Zyxel NSA3xx series of NAS units.
>
> A patch is included to add it to the device tree for the NSA320 model,
> patches to the other device trees will be included if testers come
> forward (I already have a possible tester for NSA325).
>
> There are no dependencies between the patches so I guess the first two
> should go via the hardware monitoring maintainers and the third via
> the ARM mvebu maintainers.

You are right. However the first tow patch are misnamed, they better
should be called:
hwmn: Define binding for the nsa3xx-hwmon driver
hwmn: Create a driver to support the hardware monitoring chip

The last patch seems OK for me, and the binding has been approved. So
when you will get a review from the hwmon maintainer, I will apply the
last patch in the mvebu tree.

Thanks,

Gregory

>
>  [PATCH 1/3] Define a binding for the hardware monitoring chip present
>  [PATCH 2/3] Create a driver to support the hardware monitoring chip
>  [PATCH 3/3] Add an entry for the hardware monitoring MCU
>
>  Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt |  21 ++++++++
>  arch/arm/boot/dts/kirkwood-nsa320.dts                  |  13 ++++-
>  drivers/hwmon/Kconfig                                  |  13 +++++
>  drivers/hwmon/Makefile                                 |   1 +
>  drivers/hwmon/nsa3xx-hwmon.c | 223
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>  5 files changed, 269 insertions(+), 2 deletions(-)

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com