From mboxrd@z Thu Jan  1 00:00:00 1970
From: marcel.ziswiler@toradex.com (Marcel Ziswiler)
Date: Fri, 29 Apr 2016 19:23:06 +0000
Subject: [PATCH v2 00/10] STMPE fixes/rework and add STMPE1600 support
In-Reply-To: <1461845589-4826-1-git-send-email-patrice.chotard@st.com>
References: <1461845589-4826-1-git-send-email-patrice.chotard@st.com>
Message-ID: <1461957784.3869.50.camel@toradex.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On Thu, 2016-04-28 at 14:12 +0200, patrice.chotard at st.com wrote:
> From: Patrice Chotard <patrice.chotard@st.com>
> 
> 
> This series cleans and fixes some bugs in MFD/GPIO STMPE drivers and
> prepare
> ?the ground to add new STMPE1600 support.
> 
> STMPE1600 datasheet is available here :?
> http://www2.st.com/content/st_com/en/products/interfaces-and-transcei
> vers/
> i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
> 
> Only STMPE1600 has been tested on STM32 platform. As i have no board
> with
> others STMPE
> variant(STMPE610/STMPE801/STMPE811/STMPE1601/STMPE1801/STMPE2401
> and STMPE2403), i put in CC boards's maintainers which are using
> others STMPE variant.
> 
> If they can kindly check that no regression has been introduce by
> this series
> :
> 
> For ARM/FREESCALE IMX / MXC ARM ARCHITECTURE:
> 	_ Shawn Guo <shawnguo@kernel.org>
> 	_ Sascha Hauer <kernel@pengutronix.de>
> 
> For ARM/SOCFPGA ARCHITECTURE
> 	_ Dinh Nguyen <dinguyen@opensource.altera.com>
> 
> For SPEAR PLATFORM SUPPORT
> 	_ Viresh Kumar <vireshk@kernel.org>
> 	_ Shiraz Hashim <shiraz.linux.kernel@gmail.com>
> 
> For Apalis/Colibri board SUPPORT
> 	_ marcel.ziswiler at toradex.com
> 	_ stefan at agner.ch
> 	_ dev at lynxeye.de
> 	_ Thierry Reding <thierry.reding@gmail.com>
> 	_ Alexandre Courbot <gnurou@gmail.com>
> 
> For ARM/Ux500 ARM ARCHITECTURE
> 	_ Linus Walleij <linus.walleij@linaro.org>
> 
> 
> v1 => v2:
> 	_ update Cc list
> 	_ fix kbuild test robot warnings on original patch 3
> 	_ split patch 6 to extract usage of generic bitmask name
> 	_ split patch 6 and 7 and introduce a new way to access
> registers
> 	??for both mfd/stmpe and gpio/gpio-stmpe drivers.
> 	_ remove patch 8
> 
> Patrice Chotard (10):
> ? mfd: stmpe: Add STMPE_IDX_SYS_CTRL/2 enum
> ? mfd: stmpe: Add reset support for all STMPE variant
> ? gpio: stmpe: fix edge and rising/falling edge detection
> ? gpio: stmpe: write int status register only when needed
> ? mfd: stmpe: use generic bit mask name
> ? mfd: stmpe: rework registers access
> ? gpio: stmpe: rework registers access
> ? Documentation: dt: add stmpe1600 compatible string to stmpe mfd
> ? mfd: Add STMPE1600 support
> ? gpio: stmpe: Add STMPE1600 support
> 
> ?Documentation/devicetree/bindings/mfd/stmpe.txt |???2 +-
> ?drivers/gpio/gpio-stmpe.c???????????????????????| 167
> +++++++++++++++++-------
> ?drivers/mfd/stmpe-i2c.c?????????????????????????|???2 +
> ?drivers/mfd/stmpe.c?????????????????????????????| 161
> +++++++++++++++++++----
> ?drivers/mfd/stmpe.h?????????????????????????????|??85 ++++++++++--
> ?include/linux/mfd/stmpe.h???????????????????????|??21 +++
> ?6 files changed, 352 insertions(+), 86 deletions(-)

I gave the whole series a spin both on Apalis iMX6Q 2GB IT V1.1B as
well as Apalis T30 2GB V1.1A both featuring a STMPE811 and an EDT VGA
touch panel connected to it still works perfectly running LXDE on top
of the modesetting X driver.

Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>